Search Documents

By Z. Smieszek, W. D?browicz, J. Pawlowski, G. Krawiec, J. Czernecki, J. Por?mbski, S. Gizicki

Rapid development of the automotive industry and motorization has been observed in Poland over the last decade. This phenomenon has increased the amount of used car batteries requiring recycling and has thus posed new challenges for their processing. Orzel Bialy" S.A, is the major secondary lead smelter in Poland. Ibis paper describes the program for smelting technology modernisation and productivity increase through the application of oxy-fuel burners, which has been implemented at "Orzel Bialy'' S.A. The main objective of smelter modernisation, which was to increase the furnace productivity by 20%, has been achieved. This paper outlines the previous and present state of the lead acid battery scrap smelting technology at the "Orzel Bialy" S.A. Specifications of the burners and of oxygen installation are given. Industrial tests with the modernised smelting technology and optimisation of the process parameters are described, and the results obtained are discussed.

Jan 1, 2000

By Yong Li, Tao Jiang, Xiangxin Xue, He Yang

"In this paper, we describe the current status and research progress on the utilization of typical industrial solid wastes in China. We propose a creative method called “eco-utilizing wastes” with an aim of both integration and increment but without second-time waste and pollution, in terms of the characteristics of typical industrial solid wastes, such as titanium-bearing blast furnace slag, high-silicon iron tailing and boron-enriched slag as well as oil shale.Situation of Typical Industrial Solid Wastes in ChinaThough mineral resources in China are abundant, most of these are low grade ores. Moreover, the distribution of mineral resources is asymmetric, which causes the increase of cost and decrease of the economic benefit. Over-exploitation of mineral resources results in a large number of solid wastes. The accumulation of solid wastes not only means the waste of valuable resources, but also causes environment deterioration. There exist some problems in the current practice of the disposal of industrial solid waste, such as only emphasizing the final results and causing new pollution and waste [1]. So the research and development of a high value-added method has a high practical relevance to our nation. Based on the present status and research progress of industrial solid wastes in China, a creative new idea and method for eco-utilization of solid wastes is proposed in this paper."

Jan 1, 2012

By A. Martins, L. Goulart, E. Araujo, R. Batista, A. Costa e Silva

Steel cleanness is of great importance to the performance of almost all steel products. From very clean steel for bearings to long products used in civil construction, processing variables – in special those in steelmaking operations- must be properly balanced to achieve adequate cleanness for the desired performance. With the present complexity of steels as alloy systems, it is not efficient nor appropriate to develop these processes on empirical basis alone. Computational thermodynamics can greatly improve process development to achieve the desired cleanness level at reasonable costs. In this work, examples of these calculations and their applications to real steel processing are presented and discussed. The advantages, limitations and areas in which improvement in these calculations is desired are highlighted and discussed.

Jan 1, 2015

By Shun Myung Shin, Kang Jeong, Kyoungkeun Yoo, Jin Koo, Dong Hyo Yang, Soo Sohn

"The optimum discharging condition to dismantle the batteries without explosion was investigated to recycle the lithium primary batteries, which could be exploded by heating too much or crushing. The 3 waste lithium primary battery cells were discharged with 500 cm3 of 0.5 kmol·m-3 sulfuric acid. Fe concentration and pH increased rapidly after 3 days at 35? and after 1 day at 50?. Chromium concentration increased by 4 days at 35? and 2 day at 50?and then decreased, and nickel concentration was very low. Because Li concentration increased gradually, Li became dissolved after the dissolution of cover material. When the discharged batteries were shredded, the batteries discharged at 50°C were not exploded and those discharged during 3 days at 35°C were exploded. This result shows that the waste batteries could be stabilized within 1 day at 50°C and 4 days at 35°C. Introduction Lithium has some advantages for battery e.g. it is the lightest metals and also has the highest electrochemical potential at 3.04V[1]. For over thirty years lithium primary batteries became famous for their performance in various applications such as IT, medical, and military[2,3]. They gained a reputation for their long shelf life, constant voltage, wide operating temperature range, and low self-discharge characteristics[3-5]. World primary lithium battery market was expected to grow from $820.6 million in 2003 to $1,1355.3 million in 2010 (http://www.frost.com, Frost & Sullivan)[2-4]. The lithium primary batteries have very various sizes and components. Lithium batteries are made with lithium metal as anode active material and non-aqueous solvent as electrolyte. As cathode active material, various kinds of materials were used such as manganese dioxide (nominal voltage, 3.5V), thionyl chloride (3.6V), and carbon monofluoride (3.0V). In Korea, 50 % of the spent lithium primary batteries must be recycled because spent lithium primary batteries have been listed in EPR (Extended Producer Responsibility) of the enforcement degree of the act on the promotion of saving and recycling of resources. However, the batteries have been landfilled since there is no economic method to recycle the batteries in Korea[2,3]. When the batteries were heated too much, charged, pierced, over discharged, or short-circuited, the batteries explode because lithium reacts violently with water or air and because contents such as lithium, electrolyte, and sulfur become flammable by high temperature[4]. Therefore, it is so difficult to recycle safely the spent lithium primary batteries."

Jan 1, 2008

By Donghai Li, Cheng Pan, Pan Chen, Xuewei Lv, Mei Liu

"Chromite concentrate after beneficiation can not be directly used in the electric furnace. Therefore sintering is one of the effective way to agglomeration, by which the chromite concentrate can be utilized and the power cost of ferrochrome smelting can be reduced. The properties of raw materials and the sintering process of chromite concentrate were studied in this work. The results showed that chromite concentrate used can hardly granulated alone, while chlorite addition can improve the effect of granulation. Moisture plays an important role in sintering process. The granulation effect is optimal when the amount of water addition is 12%. Strength and abrasion index are the evaluation indexes of sinter quality. It was found that the strength of sinter increased with coke dosage increasing to 12%, and then decreased when it continuously increased. Opposite regularities were found for the abrasion index of the sinter.1 IntroductionChromium is a very important metal element which is mostly used in the production of stainless steel. In the earth, it is always formed compound with iron as ferrochromium spinel (FeO.Cr203), and its mineralogical name is chromite.[1] Currently, the global production of chrome ore is about 20 million tonnage every year , in which fine ore (less than 8 mm) accounted for about 80% [2] Although the price of the fine ore is cheaper than the lump one, too much fines will lead to the poor permeability and causes increased electricity consumption while producing ferrochrome. Therefore, the agglomeration process of chrome ore is one of the effective measures to increase the usage ratio of fine ore."

Jan 1, 2013

Segregation roasting tests were carried out on Zaire cobalt oxide ores assaying about 2% Co and 3.5 to 6.5% Cu. The major parameters tested during the laboratory investigations were temperature, dosage and type of reducing agent, dosage and type of chloridizing agent, and particle size. Results showed that standard conditions suited to the segregation of copper ores, i.e. low temperature and low dosages of reducing and chloridizing agents, resulted in the segregation of copper only, while conditions suited to the segregation of lateritic nickel, i.e. higher temperature and increased dosages of reducing and chloridizing agents, led to a successful segregation of both copper and cobalt. Under the best conditions, 88% of the cobalt and 98% of the copper could be recovered in a concentrate assaying 32.5% Cu and 8.5% Co. Alternatives to process such a concentrate are briefly reviewed.

Jan 1, 1993

By N. Tsuchida

Sumitomo Metal Mining Co. Ltd. (SMMC) is currently developing the flowsheet to treat stockpiled limonite, a type of laterite ore, at Rio Tuba on southern Palawan Island, Philippines. The new plant will be commissioned at the end of 2004. Rio Tuba Nickel Mining Corporation (RTNMC) has been mining saprolite since 1977, and the limonite ore located above the saprolite ore body has been stockpiled separately according to nickel and magnesium content. Ore from these stockpiles will be blended and used for the operation. The annual production of nickel will be 10,000 metric tons for the next twenty years. The proposed process consists of ore preparation, high pressure acid leach (HPAL), counter- current decantation wash, impurity removal and sulfide precipitation. Precipitated mixed sulfide will be processed to electrolytic nickel by the Matte Chlorine Leach Electrowinning (MCLE) process at Niihama, Japan. SMMC has established new technologies during the process development, such as zinc removal and sulfide precipitation. Applying this technology, preferential removal of zinc can be achieved by hydrogen sulfide gas with negligible loss of nickel. Precipitation of nickel by hydrogen sulfide gas is carried out at low temperature. Slow kinetics is selected for control of the particle size of the precipitated mixed sulfide. Keywords: HPAL, Zinc Removal, MS Production

Jan 1, 2004

By David G. Dixon

A mathematical model is derived in dimensionless form which simulates the effluent concentration response of reagents from spent heaps under both fresh and recycled water rinsing. The model is based on dispersion from isochoric pathways distributed in length and cross-section, oriented normal to convection channels in ideal plug flow. The effects of heap height, rinsate flow, and initial reagent concentration are examined. It is shown that the rinsing cycle undergoes a distinct shift between fast and slow rinsing at a certain time depending on the amount of stagnant solution in the heap, and the distribution of dispersion pathways. Results of preliminary column rinsing tests on both agglomerated and unagglomerated ores are presented which partially validate the model.

Jan 1, 1994

By Yuan Zeping

This paper describes the distribution and removal of the main impurities in the pyrometallurgical process ?at the Guixi Smelter. The paper discusses in detail our converting schedule?of3S-SB and injecting deeply a mixture ofNa2CO) and CaO flux into the converters to enhance impurity removal.

Jan 1, 1998

By Christian Trassy, Pierre Proulx

"Inductive plasmas are now commonly used in material processing: spraying, powder synthesis, densification or spheroidization. An inductive discharge presents, in the coil region, recirculation eddies due to the Lorentz forces, resulting in an axial backflow. If the central jet is strong enough to ""pierce"" the recirculation this axial backflow disappears on the centerline, but the external layer of the injection flow is skimmed by the remaining eddy, and particulates are rejected to the discharge periphery. To avoid this disadvantage, it is common to introduce the injection pipe inside the discharge, so that its outlet is positioned after the recirculation eddy. The powders remain confined in the axial zone, to the expense of shortened residence time.In order to increase the efficiency of the particle trajectories, a double flow injector has been designed. It enables the particles to travel closer to the axis, while the outer schrouding gas is skimmed and passes through the electromagnetic eddies. This injector is made up of two concentric tubes. The powders are injected with the carrier gas in the inner tube. A schrouding gas is injected in the annular space between the inner and the outer tubes. The powder is confined to the vicinity of the axis, resulting in a more homogeneous thermal treatment.Tungsten powders have been spheroidized with and without this device. Using the double flow injection, the spheroidization yield has been increased from 70 % up to 95 %.The design of such an injection device has. been studied and improved using numerical modelling. Another useful tool, a visualisation technique described elsewhere, has been used for the experimental study, that drastically simplifies the comparison between experimental and theoretical results: injecting yttrium oxide into the discharge results in a colorful display of the 4000 K isothenn: the ""cold"" zone, below 4000, appearing as red, and the ""hot"" zone as blue. Furthermore, it is of great industrial interest since it is a very cheap and efficient way to obtain a picture of an important isotherm."

Jan 1, 1999

By Debbie Marshall

Nickel and cobalt in lateritic ores can be extracted by either a hydrometallurgical or a pyrometallurgical route. The high-iron limonitic fraction of a deposit is best processed' hydrometallurgically while the magnesium-rich transitional and saprolitic fractions are more suited for pyrometallurgical processing. During hydrometallurgical processing, it may be attractive, for economic reasons, to blend the limonitic component with transitional and saprolitic ores, which contain higher nickel levels. However, blending increases the concentration of magnesium in the feed, leading to increased acid demands. The decision on how much ore to process then becomes an economic one. Ore samples with different magnesium contents were prepared for the leach test program by blending limonitic and transitional ores. The ore samples were slurried in seawater and tested in the Falconbridge Hydrometallurgical Pilot Plant. As expected, acid consumption increased with increasing magnesium content of the ore. For target extractions of 95% nickel and 92% cobalt, the required residual free acid concentration increased from 30 g/L at 1.7% magnesium to 50 g/L at 2.7% magnesium. When the magnesium content was raised to 3.8% and 4.6% in subsequent pilot plant testing, the final free acid requirements did not increase beyond what was observed at 2.7% magnesium. Thus, the cut-off ore composition to maximize nickel units and minimize acid requirements is between 1.7- 2.7% magnesium. Keywords: high pressure acid leaching, laterites, magnesium

Jan 1, 2004

By M. Ide, K. Takemura, S. Taenaka, K. Shinzawa

"The laser characteristic is strongry dependent upon the stoichometry of forsterite (Mg2Si04) and YSO (Y2Si05) single crystals, because of change in the valency and occupied sites of doped Cr in the lattice so that mole ratios of Mg0/Si02 and Y203/Si02 in the above single crystals must be precisely analyzed. In this study ICP-AES was applied for analyzing the mole ratios. Emission intensities corresponding to Si and Mg or Si and Y were measured at the same time with internal standard method. Preparation of sample solutions, measurement conditions of ICP-AES and interferences by coexisting components were discussed, resulting in excellently precise detennination of stoichometry of the above single crystals.IntroductionIn conventional stoichiometric analysis of single crystals, the stoichiometry is detennined by analyzing each component separately with titrimetry and gravimetry techniques. On the other hand, by stoichiometric analyses using ICP-AES, emission intensities corresponding to components are measured at the same time with internal standard method. Consequently erros caused by variation of analytical condition are canceled out.Cr-doped Mg2Si04 and Y2Si05 syngle crystals are known as laser materials. The change of valency and occupied sites of doped Cr affect the characteristic of single crystal as aleser materials. The change of state of doped Cr.Stoichometric composition of Mg2Si04 is constructed by 2mole of MgO and 1mole of Si02, and Y2Si05 is constructed by 1mole of Y203 and 1mole of Si02. In this study, required analytical precision in component mole ratio is within an error of 0.0010 for Mg2Si04 (CV=0.05wt%), and within an error of 0.0030 for Y2Si05 (CV=0.05wt%) (Table I )."

Jan 1, 1998

By Nathalie Neveux

For the first time, dehydrated ferrous sulfate was successfully used for the dry synthesis of potassium ferrate. In addition, ferrate ion is stabilized as a solid solution where hexavalent iron is partially substituted by S(V1) leading to a sulfato-ferrate having the following formula K2(Fe,S)04. This substance has an efficient life time of about six months. Ferrate ion is a powerful oxidant ( EO = 2.2V ), a bactericidal agent and possesses coagulant, flocculant properties. Its reduction generates nascent oxygen, hydroxyl groups and Fe(OH)3. Alkali metal ferrate is probably the future global agent for water treatment. Applications of this material in the field of urban and industrial effluents treatment have been investigated. Heavy metals cations such as Cu, Cd, Mn, Ni, Pb, Zn, ... were successfully removed. The results of sulfato-ferrate use for cyanide destruction, decrease in COD, soil, discoloration of pulp and paper effluents will be summarized.

Jan 1, 1999

By Wiraseranee. Chompunoot, Kazuki Morita, Toru H. Okabe

"Aiming at the development of more effective recycling processes, dissolution behavior of rhodium into molten slag was investigated. Using a pure rhodium crucible and Na2O-SiO2 slag system, equilibration experiments were carried out for 18 h at 1423-1623 K under various oxygen partial pressures of 0.005-1 atm with varied slag basicity. Rhodium solubility increased with increasing oxygen potential, slag basicity, and temperature. Rhodium dissolved into slag as rhodate ion ([RhO2]-) by the endothermic reaction: Rh(s) + 3/4O2(g) + 1/2O2-(in slag) = [RhO2]-(in slag). In the dissolution reaction, the “rhodate capacity” of slag is newly-defined. The correlation between rhodate capacity and optical basicity is reported.IntroductionDue to its high chemical resistance and outstanding catalytic properties, rhodium (Rh), one of the platinum group metals (PGMs), is utilized in various applications such as catalysts, molten glass vessels and containers, and electronic devices. Owing to the rarity of Rh resources in nature, recycled Rh from scraps such as spent automobile catalytic converters is currently considered as an important source of Rh supply [1]. According to the recycling practices, Rh is currently mainly recovered from scraps along with other PGMs such as platinum (Pt) and palladium (Pd) by a dry process (e.g., smelting), a wet process (e.g., leaching and subsequent separation of PGMs from aqueous solution), or a combination of both processes [2]-[4]. Among these processes, smelting is commonly applied because PGMs can be effectively separated from a relatively large amount of various impurities coexisting in scraps. In the smelting process, Rh and other PGMs are collected in the collector metal (e.g., iron and copper), and impurities in scraps are removed into slag [4]-[6]. The process may be carried out at a temperature range of 1573-1973 K, in either an oxidizing or reducing atmosphere. Due to the high oxidation resistance at high temperatures, Rh is expected to be collected efficiently in the metal collector rather than being oxidized and forming RhOx in a molten slag. However, Rh loss into slag does occur in this process [7]."

Jan 1, 2011

By B. Nebreda, I. Vegas, R. Vigil, O. Rodríguez, M. I. Sánchez de Rojas, M. Frías, R. García, J. Urreta

"This paper shows the possibility of reutilize paper sludge waste as supplementary cementing material for the cement manufacture. This industrial waste consists essentially of a mixture of organic matter (30%) and inorganic compound, such as calcite and clay minerals. The raw paper sludge does not present pozzolanic properties, but once calcined at 650ºC during 2 hours, exhibits high pozzolanic activity, similar to silica fume at 28 days, as a consequence of the transformation of kaolinite into metakaolinite. Calcined paper sludge was used as partial Portland cement replacements of 0, 5, 10 and 20%. Enhancement in compressive strength was appreciably obtained for 10 and 20% substitution levels from 7 days on. Furthermore, calcined paper sludge slightly reduces the initial and final setting times of cement paste. Introduction Natural pozzolanic materials have been ordinary used in different aspects of construction, mainly for their influence on the microstructure and durability of blended cement matrixes [1, 2]. Due to the regulations of environmental protection, many researches are focusing on the possibility of obtaining pozzolanic materials from industrial wastes and not from natural materials (ceramic wastes, silica fume (SF), activated clays) [3–5]. One of the most used pozzolanic products is the metakaolin (MK) obtained from the activation of natural clay (kaolinite). The positive effect that MK has on blended cement performances [6,7] and also the influence that curing temperature and matrix nature have on the reaction kinetics and stability of hydrated phases produced during the pozzolanic reaction, according to the studies carried out by Frías et al. [8,9] are well known. However, there is a worldwide trend towards the use of recycled products in cement industry. In this line, some authors have reported an alternative way of obtaining MK from waste paper sludge [10-14]. The raw paper sludge (PS), once calcined under controlled conditions (700-800ºC), produces a MK with pozzolanic properties [15-20]. The present research is part of an experimental study about alternative source for MK from the Spanish paper recycling industry and its use as supplementary cementing material. This contribution pays special attention to the option of reducing activation temperature below 700ºC. This fact has a positive effect in reducing the energy consumption, as well as in reducing environmental impacts associated with decarbonation of calcite. The chemical and mineralogical characteristics of raw paper sludge and derived calcined product are described. In addition, the influence and behavior on blended cement properties (setting times and mechanical properties) are also discussed."

Jan 1, 2008

By Terry Mandziak

Typical leach mine operations recover gold values through the application of a dilute cyanide solution onto ore within an engineered facility. Key to the success of mining operations is the, containment and management of the cyanide solutions within the facility. Properly engineered' facilities will have containment systems that are both protective of the environment while enhancing solution recovery. This paper not only discusses general containment standards, but identifies state-of-the-art containment and monitoring practices;

Jan 1, 1998

By Meyer Steinberg

"Some early experiences of a Cooper Union Chemical Engineer on the Manhattan project and his latest studies on CO2 Greenhouse Gas Mitigation Technologies are presented. Mitigating Global Greenhouse effect while maintaining a fossil fuel economy, requires improving the efficiency of conversion and utilization of fossil fuels, use of high hydrogen content fossil fuels, decarbonization of fossil fuels and sequestration of carbon and CO2 applied to all energy consuming sectors of the economy including electric power generation, materials production, transportation and industrial domestic heating. Decarbonization means removal of carbon as C or CO2 either before or after fossil fuel utilization and sequestration means long term disposal of C or CO2. The review will cover the principles of removal and recovery from power plant, stacks, the oceanographic and geological disposal of CO2 and the conversion of CO2 to gaseous and liquid transportation fuels. The global economic aspects of CO2 mitigation technologies are touched upon.IntroductionThis is an odyssey of a chemical engineer. My career started with the production of U235 at the Gaseous Diffusion Plant in Oak Ridge, Tennessee and the production of PU-239 metal at Los Alamos on the Manhattan Project. After 40 years at Brookhaven National Laboratory, I wound up performing studies on CO2 mitigation technologies. The following is a power point presentation on the subject of global warmingThe DOE is proposing to increase its sequestration development program in order to maintain the utilization of our vast resources in coal both for power and for transportation fuel production. Congress is considering steps to promote energy efficiency in attempts to solve not only the CO2 problem, but also the prime problem of energy supply. We will be promoting increases in energy efficiency as time goes on."

Jan 1, 2008

By G. G. Richards

"The slag fuming process has operated for close to 70 years to recover zinc from lead blast furnace slag. The process is normally carried out through the batch treatment of slag by submerged injection of coal and air. Within the bath the coal acts as both a reductant, to reduce Zno to zinc vapour, and a fuel, to maintain bath temperature during the endothermic reduction process. The partition of coal between the slag, combustion and bypass is dependent on factors such as bath depth and injection pressure. The option of continuous fuming has been pursued at the D. Blagoev smelter in Bulgaria using heavy fuel oil as reductant/fuel. There has, however, been little attempt at commercial continuous fuming with coal. This paper presents an analysis of a coal-based continuous slag fuming furnace. The data on the Plovdiv fumer is used as a reference point. Critical design criteria for continuous fuming include the slag feed rate, degree of coal combustion and furnace size. Mathematical modelling analysis suggests that continuous fuming with coal can achieve respectable zinc/coal ratios.IntroductionThe slag fuming process was developed in the early part of this century to recover zinc from non-ferrous smelting slags [1-3]. The majority of installed furnaces were put in place to fume zinc from lead blast furnace slag on a batch basis. In most cases coal is used to effect reduction of zinc oxide, but one furnace uses natural gas [4] and, in a curious twist, a continuous fumer was developed based on fuel oil [5].Given the general nature of blast furnace lead smelting, it is not surprising that slag fuming has remained a batch process, in spite of the advantages that could be gained by moving to continuous fuming. Blast furnaces are usually operated as relatively independent units, and tapping has traditionally been done into ladles. The presence of a crane aisle makes direct coupling of the blast furnace to a slag fumer difficult, especially in a retrofit situation. Furthermore, steady-state blast furnace operation is not easy to achieve. The size of these furnaces and the nature of their feed make it difficult to guarantee constant operation."

Jan 1, 1996

By Staia. Mariana H.

Thermochemical equilibria of the heterogeneous system Ti-N-H-CI-Fe-Cr-Mo-Ni-Mn-C were calculated by using a commercial software based on the minimization of the free energy. Equilibrium calculations were done for temperatures varying between 800" and l 100°C and an initial molar relationship between reactants, a=NJTiCI,, of 0.1 to 2. The deposition process was considered to occur at atmospheric pressure. The activities of the alloying elements of the stainless steel were considered equal to their molar fractions. It was shown that for the conditions studied the substrate is no inert with respect to the gaseous phase. The existence of liquid chlorides was predicted for temperatures between 800" and 850°C and a ratio between 0.3 and 0.9. The most important metallic chlorides which appears to be present from the calculations in appreciable quantities in the gaseous phase are iron dichloride and manganese dichloride. In the low-temperatures zone and for low initial nitrogen contents, it result that the appearance of the liquid chlorides seems that partially inhibits the production of gaseous HCI. The highest deposition process efficiency calculated is obtained at a temperature 2 900°C and a N2/TiCI, ratios 2 0.7.

Jan 1, 1995

By V. I. Lakshmanan, R. Roy

Base metals and PGMs are currently recovered from sulfide concentrates using pyrometallurgical processes. These processes suffer from several limitations such as being capital intensive, scaling problems, S02 emissions and long delay in value recognition. Alternative hydrometallurgical technologies have so far not been successful and currently total pressure oxidation and partial pressure oxidation hydrometallurgical technologies are being evaluated. Process Research ORTECH has developed a unique hydrometallurgical process to recover base metals and precious metals using mixed chloride technology. In a first stage leach, base metals are recovered and elemental sulfur is liberated from hydrogen sulfide formed during this leaching stage. During second stage leach, precious metals are recovered using proven separation technologies. Some of the advantages of the process are the recovery of elemental sulfur from sulfide sulfur, recycle of the chloride lixiviant thereby eliminating effluent treatment steps and use of excess energy from the Claus reactor for the pyrohydrolysis step.

Jan 1, 2011