Search Documents

"The adsorption of mixed cationic/anionic surfactants with different molar ratios onto quartz was investigated. The cationic surfactant used was dodecylamine bromide (DDA), and the anionic surfactant was sodium oleate (NaOL). The critical micelle concentration values for the individual surfactants and their corresponding mixtures were determined using a platinum plate. The adsorption mechanisms of mixed surfactants on quartz were studied using contact angle measurements, flotation tests and adsorption amount measurements. At alkaline condition, NaOL depresses DDA flotation of quartz without depressing the adsorption of DDA. The molar ratio of mixed surfactants is found to be a key factor in the orientation of alkyl chains and thereby the flotation response of quartz. A mixture of 1/2 or 1/3 DDA/NaOL forms on the surface of quartz when the concentration of NaOL is higher than that of DDA. The adsorption of the mixture decreases the wetting of quartz since the alkyl chains are in chaotically orientation with a conceivable number of head groups directing towards the solution phase. These results provide important insights into the adsorption of mixed surfactants onto quartz surface. INTRODUCTION Froth flotation is known as an effective method of separating mineral particles on the basis of their surface chemistry, specifically their hydrophobicity. [1]. The hydrophobic particles will attach to the bubbles and rise to the top of the containing vessel to form a froth that flows over the lip of the vessel. The hydrophilic particles remain in the liquid [2]. In the process, surfactant is often used as collectors for surface modification in order to change the wetting properties of mineral particles. The primary long chain alkyl ammonium salts are the most widely used as collectors for the flotation of oxide minerals, such as quartz, muscovite, hematite, phosphate and feldspar [3, 4]. Adsorption mechanism of alkyl ammonium salts on oxide minerals has been extensively analyzed [5, 6]. Generally, the ammonium salts are adsorbed through electrostatic interaction of the polar group of the molecules with the surface of these minerals [7]. Despite many obvious advantages of the ammonium salts in low temperature resistance and hard water resisting, however, their unavoidable drawbacks, such as high sensitivity and poor selectivity for slimes, relatively high cost, have limited their applications [8]. In recent years, mixed surfactants have drawn much attention due to their superior physicochemical and surface properties than single surfactants [1, 9-11]. They have been used in many industrial processes such as dispersion/flocculation, flotation, detergent, corrosion inhibition, cosmetics, foods, paints, chemical mechanical polishing, enhanced oil recovery, and nanolithography [12]. Most of the mixed surfactants have synergistic advantage in reduction of the surface tension and critical micelle concentration (CMC); therefore, they exhibit spurious properties, like excellent surface/interfacial activities, and are less expensive than single mixed surfactant systems [13, 14]."

Jan 1, 2016

By Yushuai Xian, Youjun Tao, Fangyuan Ma

This study compared particle size distribution and density distribution of crushed products for waste printed circuit boards (WPCBs) before and after heat treatment. The crushing process for heat-treated WPCBs is a selective crushing process; more metal is concentrated in the coarse particle range of 1.0–0.5 mm and high density range of 2.8–2.96 g/cm3. WPCBs were separated using the Falcon separator to recycle useful metals. The Box-Behnken module of Design-Expert was used to obtain optimal separation parameters, namely, rotational frequency of 25 Hz, recoil water pressure of 0.025 Mpa and feed speed of 34 ml/s. On this basis, the separation indexes for WPCBs with and without heat treatment were compared. Experimental results show that the recovery effect is better for heat-treatedWPCBs than for thosewithout heat treatment. Comparedwith the non-heattreatedWPCBs, the product grade of heat-treated WPCBs is 1.95% higher, and its recovery is improved by about 14%. Finally, characteristics ofWPCBs before and after heat treatment were analyzed on the basis of stress experiments and scanning electron microscopy (SEM), respectively. Results of mechanical characterization indicate that the stress experiment for non-heat-treated WPCBs has a maximumpressure load of 212 N and displacement of 20mm, but heat-treatedWPCBs only need 140 N stress and 14 mm displacement. SEM shows that copper foil and fiberglass cloth are deformed in different directions and sizes after heat treatment to form gaps, which promote liberation of copper foil and fiberglass cloth.

Sep 10, 2020

By Peter G. Chamberlain

Domestic mining will not produce a significant portion of the manganese consumed in the United States unless new mining and processing techniques are implemented that will enable domestic lean ores to economically compete with rich foreign ores. One mining-processing technique that appears promising for certain deposits is in situ and/or heap leaching with aqueous SO2. Since leaching offers economic advantages of low capital costs, low operating costs, and short start-up times as well as environmental and safety improvements over conventional mining-processing, the Bureau of Mines studied the leachability of manganese deposits from several districts. Manganese oxides, hydroxides, and carbonates were leached to 80 to 90 pct recovery in 7 to 40 days of leaching with a solution containing 5 pct SO2 in column leaching tests. Preliminary cost analyses of surface mining-heap leaching, block caving-in situ leaching, and shrinkage stoping-in situ leaching indicate that the products of manganese leaching may be economically produced for the chemical and electrolytic manganese industries. The easiest marketable product to obtain would be a manganese sulfate commonly used as a fertilizer amendment. Manganese carbonates and hydroxides could also be precipitated from the pregnant leach solutions.

Jan 1, 1983

By Todd Kilduff, James Grillo, Shrey Arora

In efforts to improve ingress/egress from the existing subway platforms in PATH’s Exchange Place Station, a new 18-foot horseshoe cross-passage tunnel was constructed by Walsh Construction who retained Kilduff Underground Engineering for design of the initial support system and to install and maintain geotechnical instrumentation. The project presented some unique challenges as a result of the proximity to pedestrians on the platform. PATH service remained uninterrupted, limiting the Contractor to mechanical means of excavation to advance the heading. The logistics proved very challenging for the approximate 100-foot-long tunnel excavated in soft Manhattan Schist. This paper will present the design and construction challenges for the project.

Dec 1, 2022

By D. J. Pandelis, W. J. Schlittler

Auxiliary Equipment pumping systems to support primary, secondary and regrind grinding circuits will be the primary focus of this paper. Every grinding system is unique and requires special design considerations for proper application of pumps to transport mill discharge. To satisfy the majority of applications, a new series of pumps has been developed by Svedala, known as World Class Pumps. Selection of these newly developed pumps for each type of grinding circuit will be presented. Specific components of selection are materials of construction, piping system, classification method, material characteristics and slurry characteristics. Both horizontal and vertical pump applications will be reviewed with emphasis on rules of pump piping and sump design.

Jan 1, 1999

By Edward S. Hsia

Pluor Utah has been closely associated with the engineering and construction of earth bottom thickeners for porphyry copper operations, for the counter-current decantation circuit of a gold cyanide plant and similar applications in mineral processing. During the past 13 years, some 18 of these thickeners have entered service and the bottoms have proved to be watertight structures with no particular problems encountered. In the course of this work, technological advances have been realized in the procedures for engineering and construction of these units to assure watertight basins and achieve all possible economies in construction. This paper describes the successful application of engineering and construction techniques for a number of these thickeners.

Jan 1, 1977

The Putnam Coal Mine, at design capacity, will be the third largest underground bituminous coal mine in the world and will feature the world's longest single flight belt conveyor. Construction is now in process; initial mining will commence in early 1969 and design capacity will be reached in 1971. I'm Jerry Workman, Assistant Mining Manager for the Coal Group of the Mining and Metals Division of Union Carbide Corporation, and I am acting as Project Manager for installation and start-up of the Putnam Mine. The Putnam Coal Mine reserves are located in south-central West Virginia and contain approximately 27,000 acres of prime Pittsburgh No. 8 coal; reserves are sufficient to support a 3.5 MM tons per year operation for over 30 years. The mine portal area is located some six miles inland from the Kanawha River. The river loading facility is located approximately 156 miles by way of river from the market.

Jan 1, 1968

By L. Patts, J. Rohrbaugh

The Mine Safety and Health Administration (MSHA) has received several reports of filters igniting when high-temperature disposable filters were used on non-cooled diesel exhaust systems in underground coal mines. Based on laboratory testing (to determine the ignition temperature of these filters, which were loaded in the field with diesel particulate matter, or DPM), MSHA determined a maximum safe operating temperature for high-temperature disposable filters. When the results of the laboratory filter ignition testing were reported to the Coal Diesel Partnership (comprised of members of the Coal Industry, Labor, NIOSH and MSHA) the Partnership charged NIOSH with investigating the safe use of high-temperature disposable filters. This paper reports on the design, fabrication and testing of a unique exhaust gas cooling device and the ability of this device to successfully lower filter inlet temperatures and thus reduce the potential for fires.

Jan 1, 2009

A computer simulation of the automatic control of continuous mining machines has been prepared, similar to previous simulations of longwall mining systems and coal thickness sensors. The simulation allows for programmed variation of the horizon detection method, the azimuthal guidance system, the type and configuration of the miner, varying hardness in the unmined face material (leading to varying error in the machine heading), and the miner's cutting cycle. It simulates control of the miner in three axes. Use of the simulator makes it possible to anticipate problems arising from the complex character of underground mining, which include unpredictable multi-pass coupling and unpredictable variation in geological conditions.

Jan 1, 1993

By Ernest E. Thurlow

"Western Coal" in this paper is limited to those deposits of subbituminous coal and lignite in the States of Montana, Wyoming, and North Dakota. The characteristics of the coal are discussed as well as the history of mining and current mining operations for steam coal. The future of the region is tied closely to the ultimate conversion of coal to oil and gas products. Problems of industrial water supply and environmental considerations are covered together with a brief review of current legislation's actions affecting strip mining.

Jan 1, 1973

By P. Tong-jiang

We studied mineralogical characteristics of the vermiculite samples from seven mines in China. We found three types of interstratified structures in the investigated samples: 1:1 regular interstratified structure, segregated interstratified structure, and random interstratified structure. The vermiculite samples from six mines are mainly composed of phlogopite?vermiculite interstratified minerals, and the samples from the other mine are composed of chlorite?vermiculite interstratified mineral. The samples with phlogopite?vermiculite structure have high contents of K2O, TiO2 and Na2O. The samples with chlorite?vermiculite structure have the highest contents of MgO and Al2O3. The cation exchange capacity of the samples is 17.3?99.0 mmol/100g.The exchangeable cations of phlogopite?vermiculite samples from Weili Mine mainly include Na+ and Ca2+, while those of phlogopite?vermiculite samples from Tongguan Mine mainly include Mg2+ and Ca2+. The thermal expansion ratio of the samples is between 9 and 32. The exfoliated vermiculite products from Weili Mine have the best mechanical strength.

Feb 27, 2013

By Ronald L. Wiegel

In a mineral processing plant there are a number of routine decisions which are based at least in part on the plant's metallurgical performance. Among these are those related to: 1) equipment functioning properly 2) suitable operating conditions 3) reagents achieving desired results 4} determining operating response to changes in ore 5) defining circuits offering potential for improvement A step beyond the routine, are the periodic management evaluations of operating supervision and technical assistance, which are based largely on profit -a direct function of are availability, metallurgical performance and operating costs. The "yardstick", excuse me -"meterstick", by which performance is best measured is the plant metallurgical balance, which tells not only what was produced but how it was produced. Since this metallurgical balance is directly related to both plant profits and individual rewards, it is only reasonable to make that "meterstick" as precise as humanly possible.

Jan 1, 1978

By Taner Aydogmus

The A$29 billion Chevron-operated Wheatstone Project is one of Australia’s largest resource projects. Located at Ashburton North, 12 kilometers west of Onslow in Western Australia, the project will consist of two Liquefied Natural Gas (LNG) trains with a combined capacity of 8.9 million tons per annum and a domestic gas plant. The LNG Plant will serve the offshore gas fields, which are situated some 250 km off the coast of Onslow in Western Australia. Once operational and on-stream, the Wheatstone Project will contribute to Australia becoming the world’s second largest exporter of LNG. For crossing the environmentally sensitive shore area, a micro-tunnel with an internal diameter of 2 m and approx. 1,242 m in length has been constructed by means of the pipe-jacking method. The micro-tunnel will accommodate a 1.1 m diameter pipeline (trunkline) to deliver gas from the offshore fields LNG Plant. The Wheatstone shore crossing design involves a number of unique challenges owing to its coastal location, where the alignment crosses through a shore area and terminates in a marine environment. This paper provides an overview of the Wheatstone Shore Crossing Project, presents the key features, and discusses the main aspects of the micro-tunneling design.

Jun 13, 2021

By J. A. Marts, R. C. Gilmore, S. Saki, J. F. Brune

El modelamiento de la dinámica de fluidos computacional (CFD por sus siglas en inglés) implica la creación de un dominio de cálculo llamado malla o rejilla para resolver las ecuaciones que definen la física del flujo de fluidos. Este proceso comprende a menudo emplear la mayor parte del tiempo en esfuerzos de modelamiento. En un proyecto patrocinado por el Instituto Nacional de Seguridad y Salud Ocupacional (NIOSH), los investigadores de la Escuela de Minas de Colorado utilizaron un enfoque innovador de mallas, el cual permite una fácil adaptación del modelo CFD para adaptarse a una variedad de geometrías de minado de tajos largos ventilados por canales (bleeders) y progresivamente sellados (referidos a menudo como bleederless en los Estados Unidos), con la porosidad y la permeabilidad de la cámara escalables en un amplio intervalo. En este trabajo se presenta la metodología del enfoque de enmallado y escalado junto con las recomendaciones para el uso de modelos CFD en aplicaciones de ventilación para las cámaras en tajos largos. La nueva técnica de enmallado se utilizó para evaluar la función de un retorno hacia atrás en una cámara progresivamente sellada y otra cámara ventilada por canales.

Jan 1, 2014

By R. Dorey

The Kennecott Ridgeway Mine in South Carolina is scheduled to complete mining and ore processing in the last quarter of 1999. Tailings are disposed in a 300 acre, lined tailings impoundment. To facilitate closure and reclamation, modification of the tailings impoundment operation has been adopted. Mining involved the sequenced development of two open pits. In 1996 mining of the South Pit was completed and backfilling of the pit with waste rock from the North Pit was initiated and will continue until mining ceases. Both pits will be reclaimed as fresh water lakes. This paper presents the physical, geochemical and hydrogeochemical evaluation of the operational and post operational management of the project. Comparison of the operational monitoring data against predicted performance is reviewed.

Jan 1, 1999

By P. Semberg, B. Bjorkman, C. Andersson

"In this study, the interaction between magnetite and the additive olivine was studied after oxidation as well as after isothermal reduction at temperatures in the 500º-1,300º C range. In the olivine sample, the forsteritic olivine particles react partly during the oxidation pretreatment to form magnesioferrite and vitreous silica along the particle corona. This breakdown of the olivine particles during oxidation liberates magnesium from the particles, which do not react until temperatures of above 1,150° C in reducing atmosphere. When the hematite in the sample is reduced, and when the temperature is high enough to allow solid-state diffusion at ~800º C, the magnesium of the magnesioferrite redistributes, so that the magnesium concentration approaches the same level throughout the iron oxide structure. For magnetite, this did not occur until 800° C. At 1,000° C, this magnesium reacts further with the silica in the glassy slag phase, which crystallizes into fayalitic olivine. At this temperature, the magnesium has diffused over distances of more than 600 µm from large olivine particles after 2 hrs reduction. From this point, the primary slag phase in the pellet, until melting, is solid fayalite. Upon reduction to metal, the metallization front concentrates the MgO in the remaining wustite, which can lead to MgO levels of up to 10 mole% locally. The melting point of the fayalite is raised from 1,145º C to a melting range of 1,238-1,264º C due to the MgO increase, as estimated based on phase diagrams, which were adapted to the pellets tested. Much of the olivine that remained unaltered in the oxidation process will be encapsulated by iron before the particles begin to dissolve in reducing conditions and, therefore, plays no role in the reduction before final melting of the particles occurs.IntroductionEnvironmental concerns have placed increasing pressure on the CO2-intensive iron and steel industries to further optimize operation toward higher productivity and more efficient use of reducing agents. At the same time, high demand for iron ore has caused new iron ores with lower grades and more complex chemistries to be taken into production. In Scandinavia, the main iron-bearing material is magnetite-based pellets with olivine, which allow operation with very low slag volumes and, hence, lower fuel rate ( Slagnes and Sundqvist Ökvist, 2008; Hallin et al., 1994). Both the MgO and SiO2 of the olivine, as well as the elements of the gangue of the ore, i.e., Si, Mg, Ca, Al and alkali, interact with the iron oxides to give the finished pellet product its final properties in the blast furnace. Tailoring the additive mix to be used for a certain iron ore for optimal product properties, therefore, requires detailed knowledge of the mechanisms by which these elements dissolve and react in the pellet."

Jan 1, 2015

By Horry Parker Jr, Jason Gillespie, Justin Kolster, Stephen O’Connell

Construction of the 5,932-ft Reedy River Basin Sewer Tunnel in Greenville, SC was marked by a critical transition from drill-and-blast mining in mixed-face conditions to TBM excavation with limited rock coverage. In this paper, we discuss the geological, geotechnical, and risk management considerations for transitioning to TBM operations in variably weathered gneissic bedrock. After construction of an unexpected 230-ft starter tunnel due to differing site conditions, the 11-ft diameter TBM was successfully launched in December 2019 without significant ground support issues. This project highlights the effectiveness of extensive rock probing to fully characterize bedrock topography prior to the TBM launch.

Jun 13, 2021

By Peter Shuttleworth, Chris Fesq, Eddie Woods

Precast concrete segmental linings for tunnels have traditionally been designed with conventional steel bar reinforcement. In many cases, this has been satisfactory in service, but in others, major problems have occurred with the durability of the linings. Commonly this has resulted from corrosion of the reinforcement, mainly from chloridesin ground water, causing spalling of the concrete and leading to very expensive and disruptive repair programs. This paper discusses the relative merits of designing tunnel linings with steel fiber reinforcement to provide long-term durability, improved impact resistance and toughness for greater load capacity across joints, enhanced robustness during transportation and erection, plus improved fire resistance with the addition of polypropylene fibers. Guidance is also given in the selection of the correct fiber type, mix design and testing methods to establish the optimum dosage required and production techniques to ensure even distribution and compaction.

Jan 1, 2005

By J. R. Kunkel, V. Lishnevsky

At mine sites, the operational and required storage volumes of solution and water storage ponds and reservoirs are usually calculated based upon a water-balance approach. Many climatological variables including precipitation, air temperature, solar radiation, pan evaporation and relative humidity along with operating parameters, are used in the water-balance model. The water-balance model often seeks to find a “critical period” of wet or dry climatological sequences which result in a “maximum” pond storage volume or water demand. The problem with this approach is that the designer usually does not know when the project will come on line in relation to the historical record. To avoid this pitfall, we use a more robust approach. In the more robust method, the water-balance calculations begin in each year of the historic climatological record. This method results in the same number of water-balance runs (or realizations) as the number of years of climatological record. Results of this type of analysis guarantee that the critical period or maximum required pond volume will be found if it is assumed that the historical climatological record repeats itself or if a synthetic time series is used. In addition, this method permits calculation of the likelihood (probability) that a given pond volume will be equaled or exceeded in any given month of the operational life of the facility. In this paper, the results of the sizing of a heap leach pad solution pond are presented along with the probabilities of a given solution pond size being equaled or exceeded based on the robust water-balance approach.

Jan 1, 2002

By A. Tordoir, S. S. Kanchibotla, W. Rogers, E. Engmann, B. Bisiaux, S. Ako

Blast-induced rock mass displacement can have a significant impact on ore loss and dilution. The mischaracterization of the grade boundaries both prior to, as well as a result of, blasting can lead to significant financial losses due to ore loss and dilution. Ore dilution occurs when waste material is miscategorized as ore and sent for processing or stockpiling, diluting the run-of-mine head grade and recovery. Ore loss takes place when valuable mineral is miscategorized as waste and sent to the waste dumps, thus never being processed and recovered. Extensive research has been conducted at the University of Queensland over the last fifteen years to understand the impact of blast movement on ore loss and dilution. Recent outcomes of this research have led to the development of innovative tools and techniques to measure and model blast movement. These techniques have been implemented at the Ahafo gold mine in Ghana to understand blast movement dynamics and to implement solutions to reduce blast-induced ore loss and dilution. These solutions are validated through controlled trials and have been incorporated into site standard operating procedures.

Jan 1, 2012