Search Documents

By R. L. Derick

On a regular basis, mine personnel should obtain air samples directly from active underground areas as well as remotely from sealed locations. These samples provide mine officials with data relative to the makeup of the various atmospheres. Should conditions underground change, these results can provide a baseline that can assist officials in determining the extent of change. Relating the concentrations of individual gases to time, applying gases to equations, and examining their change over time are tools that have been successfully used to determine if a heating event exists and, if so, the extent of the emergency. These atmospheric status equations have either been developed for the mining industry or adapted from other industries. They serve as tools to assist personnel in determining the condition of underground mine atmospheres. As long as the problem area continues to be ventilated, certain gases, gas ratios, and equations can be used to determine if a fire exists, what type of material could be burning, and what quantity of coal is burning. Once the mine or the involved section has been temporarily sealed, gases, ratios, and gas-derived equations can assist personnel in determining how conditions within the sealed volume are changing over time. To alleviate potential explosions when fresh air is once again introduced into the sealed volume, equations and a diagram have been developed to predict the likelihood of an explosive atmosphere. Similarly, prior to commencing recovery of a mine or section, equations exist that can assist in determining if the fire will rekindle when air is reintroduced. This paper serves as an overview to remind and/or instruct readers about gas-sampling methodologies and gas analyses to assist in determining the status of underground atmospheres.

Jan 1, 2006

By Jacob Grasmick, Bill Newns

Despite ongoing digitization and “hardware” technological advances, geotechnical uncertainty remains the most significant risk in underground and tunnel construction. And, whilst they are commonly held up as an example of the sophistication of the industry, the practice of drafting and using geotechnical baseline reports is subject to a wide range of influences, not all of which support good risk management. Uncertainties in predicting ground behavior, the gap between the pre-construction assumptions, and the systemic response to construction remains a significant technical and communication challenge. Accordingly, this paper presents a framework to quantify geotechnical uncertainty using geostatistics and translate these into practical tools for ground risk management throughout planning, procurement and construction. Adopting even some of the principles of this framework should provide improvements to contract risk management and should assist to minimize the potential for commercial losses.

Dec 1, 2022

By E. Galán

The largest Spanish kaolin deposits formed on granites occur in Galicia (NW Spain) due to a widespread kaolinization of Variscan granitoids. This paper provides insight of the origin of this kaolinization process on the basis of a mineralogical and geochemical study carried out in two kaolin deposits, presently mined to be used in the paper industry. Mineral composition of the deeply kaolinized rocks is dominated by well-ordered kaolinite with minor quartz, K-feldspar, mica (illite/muscovite), locally gibbsite, and traces of resistant accessory phases (rutile, ilmenite, zircon and monazite). The content and structural order of the kaolinite decrease with depth. Kaolinite formed by extensive replacement of feldspars (plagioclase). Differential mobilization of major and trace elements during kaolinization has been inferred by using a mass-balance approach. Significant amounts of Na, Ca and minor Mn, Sr, P and U were removed from incipiently leachable minerals (plagioclase and apatite), and K, Rb, Cs and Ba were released from K-feldspar and mica. On the contrary, Ti, Zr, Th, Hf and the REE are retained in the resistant trace minerals that are concentrated in the fine fractions of the kaolins.

Jan 1, 2010

By Yi Luo

Subsidence events occurring above inactive room-and-pillar (R&P) mines, including abandoned mines or sealed portions of active mines, are classified as unplanned subsidence, because of their timing and distribution are unpredictable. When investigating such subsidence cases, many uncertainties exist and disputes often focused on whether the observed structural damages are caused by mine subsidence or other natural or artificial causes. However, solid evidence to identify the cause is often lacking. In order to conduct a complete and impartial investigation, thorough knowledge of subsidence theories and other ground control topics, as well as broad experience, are required.

Jan 1, 2011

By Feridon Ghadimi, Saeed Mojeddifar, Massume Khavari

Separation of geochemical anomalies from background is an important and essential issue in the exploration of mineral deposits. Statistical methods are used to separation of anomaly from background. Fractal/multifractal and singularity methods are very suitable for the separation of weak anomalies. For interpolation, various methods could be used such as most distance-weighting methods, kriging, spline interpolation, interpolating polynomials, and finite difference methods. This paper addressed application of multifractal techniques together with finite difference procedure to detect the anomalous regions. Fractal models such as concentration–area, spectrum–area, and singularity index model were selected to identify Pb–Zn anomalies. In this research, 170 samples from 33 boreholes were taken in the Haft-Savaran area and analyzed for determination of Pb–Zn anomaly. Singularity method was a suitable method for separating Pb and Zn anomalies. Also, the results showed that the geochemical anomaly has occurred along NE–SW trend and is consistent with the sulfide mineralization process and the faults of the region.

May 18, 2020

By Rodney R. Krause

In attempting to tell the general public about the coal industry's land reclamation efforts, we have often said, "We're not doing things by the book, because we're still writing it." Like any good catchphrase, the statement is not only striking but true. It is particularly true in the mountains of Appalachia, where the problems of mining; and of reclamation are made more intense by the nature of the terrain. Mining and reclaiming the land "by the book' --which is to say by the methods of contour mining traditionally used in hill country--hasn't worked too well. So a lot of conscientious coal operators and associations are trying new methods--new ways of mining, new machines for seeding and planting, and new species to seed. Not all their experience can be transplanted to other areas, and of course I don't believe that Appalachia is the only place where new methods are being developed. Nevertheless, there's enough action in Appalachia to make a detailed examination rewarding, so let's focus on the hills to see what's new.

Jan 1, 1970

By J. A. Botín

Identifying, quantifying and minimizing technical risks associated to investment decisions is a key challenge for the minerals industry decision takers and investors. However, risk analysis in most bankable mine feasibility studies are based on stochastic modelling of project NPV which, in most cases, fail to provide decision makers with a truly comprehensive analysis of risks associated to technical and management uncertainty and, as the result, are of little use for risk management and project optimization. This paper presents a value-chain risk management approach where project risk is evaluated for each step of the project lifecycle, from exploration to mine closure, and risk management is performed as part of a stepwise value added optimization process.

Jan 1, 2011

By James B. Fletcher

The Miami mine is located near the town of Miami, Gila County, Arizona. The Miami mine started mining in 1910 and finished in July, 1959. The orebody was divided and mined as follows: Tons High Grade 24,400,000 - Top slicing, sub-level caving, etc. Low Grade 105,100,000 - Block caving Mixed ore 9,800,000 - " Low Grade #2 13,100,000 - " Total Mining 152,400,000 GEOLOGY Ore minerals are largely in pre-Cambrian Pinal schist intruded by tertiary Schultz granite porphyry and covered to some extent by Quarternary Gila conglomerate. The structures are highly faulted and shattered. The Miami fault on the east cuts off the ore and the Pinto fault on the southwest caused re-oxidation of enriched sulphides producing mixed ore. MINERALOGY The chief mineral is chalcocite, with chalcopyrite, bornite, covellite, malachite, azurite, chrysocola, cuprite, native copper, and molybdenite as minor minerals. The ore minerals occur in seams, veinlets and disseminated particles. In block caving there is always some dilution, and drawing of ore stops when the grade drops past an economical point. This results in a small amount of copper left in the stopes below the capping. There is some copper in the capping, probably below 0.03% or less than 0.6 lbs. per ton. Over the low grade #2 orebody and portions of the high grade there was an oxide capping which was not mined. The crushed pilars are another source of copper. The leaching at Miami is an attempt to recover this last remaining copper of a worked-out mine. The enrichment at the Miami mine had gone more nearly to completion than most ore bodies in the southwest. There is practically no pyrite in the capping and very little in the ore.

Jan 1, 1971

By S. G. Hardcastle, C. K. Kocsis

Ventilation is an expensive prerequisite for underground mining. Current mining trends, including increasing depth and mechanization and more stringent health regulations would generally dictate that more air volume is required in order to provide good working conditions underground. However, any increase in the mine’s intake airflow can produce a disproportionate increase in power consumption and hence operating costs due to the cubic relationship between the sup-plied air power and the airflow (Power a Flow3). Furthermore, forecasts of significant increase in energy prices and new commitments with regard to reductions of greenhouse gas(GHG) emissions, determined the mining industry to look into developing new concepts, design tools and incorporate the latest mining technologies in order to lower capital and operating costs while meeting commitments regarding GHG emissions. The advances in computing power and modelling software now make it possible to design, model and schedule a mine from opening to closure. A developing trend is to design and plan the mine by means of orebody modelling software, followed by using discrete-event simulation techniques to predict production rates and evaluate various operating scenarios throughout the life of the mine. The authors are currently evaluating how such process simulators could be adapted in order to forecast the need for materials or a specific resource, and one of these would be the mine’s “life-cycle” airflow demand as a function of scheduled production rates and mine operating characteristics. Further to this, based upon the mine’s life-cycle airflow demand schedule, the ventilation system could then be designed using a mine ventilation simulator. This new design approach would integrate in parallel the development of the ventilation system with the current mining conditions, therefore, heading towards “develop-as-you-go” as opposed to developing the system for final requirements with high upfront costs. This new ventilation system design criteria would also incorporate the use of the “ventilation-on-demand” technology, which will further lower development and production costs and implicitly, the mines’ GHG emissions.

Jan 1, 2004

By M. A. Rabah

This paper focuses on the separation and extraction of lead and zinc from Egyptian ore at the Eastern Desert close to Red Sea. The ore sample contains cerussite, galena, hemimorphite and other impurities. Experimental program includes flotationof galena using xanthate collector and cerussite using oleic acid as collector and sodium silicate to depress hemimorphite tailing. Galena, and hemi-morphite are converted to carbonate with sodium carbonate prior to metal extraction. Lead and zinc are extracted pyrometallurgically at 1050°C and750°C or electrochemically respectively. The overall performance of the applied method amounts to 99.2%. Extraction efficiency of lead and zinc amounts to 98% and 94.5 % respectively. A model assumed that galena and cerussite in the ore are partially oxidized and can be liberated by grinding. Oleic acid selectively reacts with cerussite in a multistep sequence. Preliminary cost estimate shows that the price of the products is competitive to their local market prices.

Jan 1, 2000

By P. Amelunxen

This paper presents the authors? personal experiences in the design and operation of moly separation circuits in copper-moly concentrators. Topics discussed include column cells versus mechanical cells; use of nitrogen; use of CO2 and sulfuric acid for pH modification; and general equipment selection and sizing. A benchmarking of main operating parameters for industrial plants is presented. Upgrading curves for commercial column and mechanical cleaning circuits are also presented, showing that with average flotation kinetics and rougher concentrate grades, technical grade concentrates can be easily achieved with five column cells operating in counter-current configuration.

Jan 1, 2009

By M. Trim, Y. Sun, D. Tepavac, A. Kumar

Configuration of Rozelle Interchange Project’s ventilation system required design and construction of some of the largest and tallest underground civil caverns attempted in Australia. The paper focuses on the technical challenges of designing these caverns within a heterogeneous, generally weak sandstone under highstress conditions while providing a construction sequence that would align with the contractor’s preferred techniques and schedule. Various construction techniques were investigated, but ultimately an observational approach relying on a construction sequence and specialized instrumentation met both the designer’s and contractor’s requirements. Relevant data obtained from excavations and the construction monitoring program are presented within.

Dec 1, 2022

By J. A. Rusnak, K. M. Mohamed, M. A. Van Dyke, M. M. Sears, G. Rashed

"Researchers from the National Institute for Occupational Safety and Health (NIOSH) recently developed a coal-mass model to realistically simulate the deformation and loading behaviors of the ribs of coal pillars in underground coal mines. The scale-dependent properties (stiffness and strength) of coal material were considered in the coal-mass model. In this paper the orientation of face cleat with respect to driving direction was integrated in the coal-mass model. The controlling parameters (dimensionless coal-mass scale and fracture strains) of the modified coal-mass model were calibrated using a published case study of coal pillar strength. Numerical models with wide ranges of controlling parameters were conducted to simulate the test pillar. The best match between the numerical modeling results and the measured stresses and deformations was achieved by using a coal-mass scale of 30 and fracture plastic shear and tensile strains of 3.25% and 0.325 %, respectively. INTRODUCTION The failure of coal pillar ribs by itself are a major hazard in underground coal mines. Furthermore, failing ribs can indirectly contribute to roof and floor instability by increasing opening widths across intersections and entryways. Over the past decade, rib failures have resulted in 12 fatalities, representing 28% of the ground-fall fatalities in U.S. underground coal mines. Mining depth has always played a very important role in assessing rib stability. Gauna and Mark (2010) completed an analysis of rib fatalities that occurred between 1996 and 2010. One of their most prominent and influential findings was the identification of a relationship among fatalities, depth, and mining height. Therefore, Coal rib stability will continue to be a challenge for future deeper mines in U.S. coal basins. In the past several decades, research efforts have focused on roof support. The current rib control practice in U.S. coal mines is to select rib bolts through a trial-and-error approach (Mohamed et al., 2015a). Rib failure incidents can be can be substantially reduced or even eliminated by adopting an engineering-based coal rib design approach. The factors affecting rib stability in coal mines are numerous and mutually dependent. These factors include but not limited to mining height and overburden depth, interburden thickness for multiple-seam mining, coal strength, cleat density, entry direction with respect to cleat orientation, existence or absence of partings in the coal, percentage of extracted roof and/or floor rock, density of rib bolt support (Mohamed et al., 2015a). Moreover, it is difficult to isolate the particular effect of a specific factor on the overall rib stability. Therefore, a reliable empirical rib design approach is not achievable because it requires a significant number of case histories to be collected in order to have a reasonable range of all of the critical parameters. However, numerical modeling can be a practical tool to assist with rib support design if the modeling is realistic, which can only be achieved through calibration and validation of the numerical model against field data."

Jan 1, 2018

By Ralph W. Barbaro

In the mineral industry, the objective of a mining venture is to extract, process, and market a mineral commodity in such a manner that the profit of the venture is maximized. In a mining venture, a company normally has control over mine production scheduling, the selection and location of processing facilities (mineral beneficiation plants, smelting plants, refineries, or blending facilities), processed ore blending, and the selection of markets. The flexibility of the above factors provides many alternatives to satisfy the needs of each market with regard to quantity and quality of ore. The purpose of this paper is to present a mathematical model for determining the alternative that yields the maximum profit. Production planning is generally concerned with the best utilization of fixed resources, more specifically, with the determination of production and inventory levels to meet fluctuating demand requirements. A mine can be any source of ore such as an entire mine, a production unit within a mine, or an independent supplier. The objective of production scheduling is to determine the times at which each mine will be used and to allocate a required level of production. Production planning and scheduling problems are intimately associated with the location of new and existing mines and processing facilities. Although the location of the mines is usually fixed, there can be considerable flexibility in locating new processing facilities, in the selection of the processing plant, and in blending the ore before and after processing.

Jan 1, 1983

By F. Calizaya

This study summarizes the results of various numerical and laboratory experiments per-formed to study the effect of airflow recirculation on gas concentration. The numerical exercises were carried out on a simulated mine ventilation net-work. The laboratory experiments were conducted at the Mackay School of Mines' airflow monitoring system in Reno, Nevada. In both cases, the airflow was recirculated through the system by means of a main fan and a set of booster fans. The booster fans were positioned to produce two types of recirculation: In line and Cross-cut. For each type, various recirculation conditions were generated by changing the booster fan pressure. During each test, the gas emission rate at the simulated working face was kept constant. The study illustrates the conditions under which controlled airflow recirculation may be used to solve a district ventilation problem.

Jan 1, 1991

By C. F. Barter, H. G. Kreis, D. S. Weber

Before and during in situ mining at the Santa Cruz In Situ Copper Mining Research Project test site, hydraulic testing was conducted at injection and recovery test wells to characterize patterns of fluid movement in the 5-spot well field. Testing included borehole spinner flow meter surveys, single-well and multiple-well injection and recovery tests, straddle packer injection tests, and bromide pulse tracer tests. Results of hydraulic testing for determination of fluid flow regimes were used to modify well and mining zone hydraulics for the purpose of increasing fluid migration in flow pathways of the mining zone with higher copper grade.

Jan 1, 2000

By C. W. Fitzgerald

INTRODUCTION Continuous mining machines are used in regular flat ore beds having uniform thickness. Since coal is the most common type of material occurring in such beds, most continuous miners are used for the extraction of coal from underground mines. The first continuous mining machine for under¬ground coal mining was introduced in 1948. In one machine, the continuous miner combines the functions performed by a conventional face drill, a cutting ma¬chine, and a loading machine. It breaks or digs the material out of the surrounding solid and transfers the material back through the machine chassis by means of a chain conveyor. The conveyor carries the material to a haulage system, usually a rubber-tired vehicle known as a shuttle car. Generally, continuous miners are used in seam heights from 890 to 3660 mm (35 to 144 in.). For seam heights of 1070 mm (42 in.) or less, the haulage system may be a multiple-bridge conveyor or battery-powered tractors that haul low-bed trailers. Proj¬ects are being undertaken by private industry and through government contracts to develop a continuous haulage system for all seam heights. As of 1976, the majority of continuous miners were of two types. The first type is the drum miner, which mounts the cutting elements on a series of drums across the cutting head of the machine, sometimes using a cutting chain to cut clearance for the gear drive. In the drum-type machines, the cutting head rotates parallel to the material face. The second type is the auger miner, which utilizes cutting elements mounted on two auger-type cutting heads. One head is located on each side of the machine, with the heads mounted per¬pendicular to the material face. Chain-head ripper-type miners/miners having rotary cutting elements with oscillating motion and twin-head boring-type miners have all been popular within the last 15 years. Although these are considered obsolete, some machines are still being supplied for specialized applications. GENERAL DESCRIPTION This chapter describes only continuous mining ma¬chines available as manufacturers' production models as of September 1976. Figs. 1 through 11 illustrate some typical machines currently in use. Cutting Elements The cutting elements are the interface between the machine and the material being mined. In describing the cutting elements, consideration must be given to the differences between the drum- and auger-type machines, the bit-tip speeds, and the bit types. Drum-Type Continuous Mining Machines: Three of the four principal manufacturers of drum-type miners use multi-motor designs that provide separate a-c motors for driving the cutting elements. Gear trains are used to reduce the speeds of the motors to the rotational speeds of the cutting elements. One of the three suppliers drives the cutting elements of its low-seam models with a heavy-duty drive chain that is equipped with cutting bits; all other functions of this machine have separate motor drives that are either electrical or hydraulic. The fourth principal manufacturer generally provides two a-c electric motors, utilizing gear reducers, drive shafts, and hydraulically operated engaging clutches to power all of the operating functions, including the cut¬ting elements. Some drum-type miners use trim chains, equipped with cutting bits, to cut clearance for the gear drives. These trim chains vary from two 305-mm (12-in.) chains to one 760-mm (30-in.) chain per machine, de¬pending upon the manufacturer's design concept. In all machines other than the low-seam models that use chains to drive the heads, the trim chains are driven by sprockets on the drive shaft of the final cutterhead drum; therefore, the trim chains are not used for power trans¬mission to the cutting elements. In addition to cutting clearance for the gear drives, the trim chains provide uniform bit spacing all the way across the head and assist in moving the cut material to an area where it is either loaded directly into the miner's conveyor or is easier to load into the conveyor. On a drum-type mining machine, the cutting ele¬ments all rotate from the top to the bottom. Therefore, the recommended procedure is to raise the cutterhead to the maximum seam height, sump the entire machine forward to maximum depth by means of a crawler drive, and then shear downward until the cutter elements reach the floor level. The maximum sump depth varies ac¬cording to the drum diameter, the type of material, the floor conditions, and the operator's abilities. It normally varies an average of 460 to 760 mm (18 to 30 in.). Cutter drums are supplied with two types of cutting bit holders. Weld-on holders are attached permanently. Pin-on holders are replaceable at the face. Cutter-drum diameters over the bit tips vary from 660 to 965 mm (26 to 38 in.), depending upon the chassis height of the machine and the range of cutting heights. Auger-Type Continuous Mining Machines: As cut-

Jan 1, 1982

By S. Mishra, C. Shon, D. Saylak

Only 40% of fly ash generated by the power plants in US are recycled and used for commercial applications. Of these, the high lime, Class C ash had been preferred. Systematic laboratory and field-scale studies have shown that, by including calcium chloride in the mix design of stabilization of roadbed materials, both Class C and Class F fly ashes can be effectively utilized. Test data reveal that the addition of calcium chloride to the system accelerates its curing rate, thereby increasing early strength and long term durability of the constructed road. For road construction, a preblended Class F fly ash–CaCl2 system tends to be more forgiving than the Class C fly ash–CaCl2 system. The former system produces more durable roads. The role of calcium chloride as an accelerator in these systems is discussed along with a mathematical model developed for fly ash- CaCl2 stabilized roadbed systems.

Jan 1, 2007

By Otto E. Zwanzig

You may think long before this talk has been completed that the speaker is belaboring the obvious. Please let me put to rest here and now any doubt which you may have in this regard by assuring you that is precisely my intent, and for a very specific reason. We all profess to know and recognize the obvious, but I am impressed increasingly how often we forget or fail to act upon the obvious. Shortly after starting my first job upon graduation from college, I was asked by my boss to participate in a course on practical communications, particularly as applied to conveying proposals effectively to the client -- be he customer or company president. The concept or philosophy underlying this program was so simple and obvious that in my youthful brashness I saw only a gross waste by the company of e good, solid $1930 in compelling me to take the course. The sequel to this experience occurred about five yews ago when I was directing a 300-man marketing group. At that time I enrolled a dozen of my department heads, and subsequently about a hundred other personnel, in the contemporary version of that sane program. Why? -- because they all knew the obvious, but I could see how imperfectly they were implementing it. Truly, a wide chasm exists all too often in our beliefs on the one hand and our practices on the other.

Jan 1, 1962

By Jose M. S. Ramos

This paper describes the slope stabilization procedure at Cauê Mine, Companhia Vale do Rio Doce - CVRD, Itabira, State of Minas Gerais, Brazil. Cauê Mine, is a large open pit, to produce about 41 million tons of iron ore during 1974, and an intensive program of investiga Lion was carried out to provide the basic data for stabilizing its slopes, The ultimate rock slope in the W area will be about 400 m high with dipping angles decreasing gradually from top to bottom of the pit. The investigations started in 1969 and since then many geologists and engineers, from both CVRD and Geotécnica S/A., assisted by international consultants, have given their contribution to the achievement of solutions. It is hoped that this paper may contribute to the slope stability of other mines in tropical climate.

Jan 1, 1974