Search Documents

By B. J. Sauer

Variable frequency drives (VFD’s), or adjustable frequency controls (AFC’s) as they are more precisely identified, have been available to the mining industry for over 20 years. However, in recent years as the push to cut production costs has become ever so crucial, AFC usage has become more widespread. This paper seeks to provide professionals in mineral processing plant design and operation with an introduction to AFC’s, insight as to why AFC control for AC induction motors can be advantageous, and specification and design considerations.

Jan 1, 2002

By K. Heasley, A. Yassien, A. Khair, S. Peng

There are three major components of a fully grouted roof bolt which primarily determine its ability to develop and sustain load: the steel rebar, the resin annulus, and the rock/grout interface. The untensioned, fully grouted roof bolt is subjected to loading only when the surrounding rock deforms. Vertical rock deformation is generally a result of strata sagging and bedding plane separation, whereas horizontal deformation is typically a result of bedding plane sliding. These two types of deformation create different types of internal loads with-in the roof bolt, tensile stress for vertical rock deformations and shear stress for horizontal rock deformations. Also, as a result of the mutual load transfer between the rock and bolt, shear stress will be developed along the grout/rock interface. According to the exact bolt loading conditions, different failure modes may occur: bolt axial failure, bolt shear failure, and shear failure along the grout/rock interface. Understanding these possible failure modes and their root causes is the key to eliminating roof failures in underground mines employing fully grouted resin bolts. Using ABAQUS 5.8, a finite element model was developed to simulate the components of the fully grouted bolt and its interaction with the surrounding roof strata. Several models were conducted to investigate how load transfer occurs between the rock and the bolt under different geological and mining conditions. The effects of bed-ding plane location and properties, and strata sequence on bolt stability were studied. Also, the effects of hole roughness on bolt stability were discussed. Bolt axial failure was not observed within the range of the studied parameters; however, a combination of high overburden depth, a bedding plane located at 2 to 3 ft from the roofline or a low coefficient of friction along the bedding plane caused strata sliding and shears failure in the bolt. Also, in the case of a weak immediate roof, the shear stress at the grout/rock interface could exceed its ultimate capacity lead to slippage.

Jan 1, 2004

Caterpillar’s 797 327-t (360-st) mining truck is currently being tested at the company’s proving facilities. Mine evaluations began in the second quarter. The unit will be commerically available in North America in 2000 and worldwide in 2001. The new model is the largest of Caterpillar’s off high-way truck line. In addition, the company has replaced its 966F series II and 970 F wheel loaders with the966G and 972G models. 797 mining haul truck Caterpillar developed the 797 mining haul truck in response to mining companies seeking to reduce cost per ton in large-scale operations. The 797 is sized to work with loading shovels used in large mining operations. And Caterpillar will match the body design to the material being hauled, to optimize pay-loads.

Jan 1, 1999

By R. J. Roman

Several research groups have spent considerable time investigating coarse ore leaching. Coarse ore leaching includes both heap and dump leaching. The term "heap leaching" will be used in this paper to mean any type of coarse ore leaching. The results of their work are generally in agreement: the progress of leaching can be described by the shrinking core model and its associated mathematics. The shrinking core model is schematically represented in Figure 1. The particle is contacted by the leach solution on its outside surface and the solution migrates inward by filling the pores on the particle. As the solution filling the pores comes in contact with grains of ore mineral the reagent chemically reacts with the ore mineral to solubilize the contained metal. The solubilized metal diffuses outward to the particle surface and is washed away by the leach solution flowing past the particle. The leaching reagent in the particle interior is replenished by the diffusion of reagent from the surface of the particle to the interior of the particle. If the chemical reaction between the leaching reagent and the ore mineral is relatively fast compared to the diffusion rate of the reagent in the solution in the pores of the particle then leaching proceeds from the outside of the particle inward resulting in a "shrinking core" of unreacted ore surrounded by a "leached shell". The rate controlling step in the reaction can initially be a chemical reaction between the reagent and the ore mineral grain, however, once the reaction has proceeded a short period of time diffusion of the leaching reagent through the leached shell will be the slow step and hence the rate controlling step in the production of metal from an ore particle.

Jan 1, 1992

By Steven B. Van Kouteren

Value added is a loosely used qualifier in the industrial minerals industry. What exactly does it mean? What does it take to make a value-added product? More importantly, how does a company maintain the value added to its products? Most people agree that value-added means the value of a mineral minus the cost to produce it. This is misleading, though, because producing value-added products does not necessarily guarantee the profitability of the products. In some cases, firms that make value-added products are not very profitable. It is important not only to understand how to make a value-added product but also how competitive forces in the market can erode the value added. Therefore, when looking at value-added opportunities, producers must understand how to obtain the value added and how to maintain that value. Four major factors limit a company's ability to add value to its products. This paper examines these factors. It uses the ground calcium carbonate and mica industries as examples.

Jan 1, 1990

By Weijie Wei, Jinwang Zhang, Shengli Yang

Due to the unbalanced top coal drawing process, the recovery ratio is low, and the equipment stability is poor in the longwall top coal caving mining (LTCC) with an inclined seam. Aimed at these problems, this paper proposes the dynamic group caving method (DGCM). The basic procedure is that when the drawn volume of top coal from a support reaches about half, the next support begins drawing top coal, and the drawing process between the two supports is half done. Taking the panel no. 8103 in Beixinyao mine as the research object, the characteristics of drawing body shape, particle movement trace, and variation of recovery ratio are investigated by using Particle Flow Code. Furthermore, the effect of mining-caving ratio on the top coal drawing law under DGCM is revealed by the simulation results, and compared with the single-opening sequence caving method (SSCM) and the doubleopenings sequence caving method, advantages of DGCM are determined in inclined seams. The results show that the drawing body can be divided into the left and the right under DGCM. Specifically, the drawn top coal particles in the left are from the upper part of this support, that in the right are from the lower part of next support, which verifies the correctness of the theoretical analysis. The characteristics of the drawing body shape are more significant when the mining-caving ratio is relatively small. In addition, with increasing mining-caving ratio, the recovery ratio of the panel both increases gradually underDGCMand SSCM.When the miningcaving ratio is less than 1:1, the recovery ratio of DGCM is obviously higher than that of SSCM, indicating that DGCM can greatly improve the recovery ratio. While when the mining-caving ratio is larger than 1:1, the recovery ratio of two caving methods is basically equal; however, the advancing time is significantly shortened under DGCM. This study are of great significance to realize high efficiency and precise caving in LTCC with an inclined seam.

Jul 7, 2020

By Dirk van Zvl

The design of cover systems for reclamation schemes in tailings requires estimation or determination of tailings materials properties such as compressibility, shear strength and consolidation characteristics. It is very difficult and expensive to obtain truly undisturbed tailings samples for laboratory testing. In situ testing methods have been developed for economically obtaining large amounts of information. Two of these methods are described, the piezocone and the flat plate dilatometer. Both of these methods provide a rapid means of detailed material identification in a nearly continuous fashion for the entire depth investigated. The equipment is described and typical data from a uranium tailings impoundment is presented. The results are compared and the advantages and disadvantages of these methods are discussed.

Jan 1, 1984

By Lee W. Saperstein

In surface mining for coal, common practice for the disposal of preparation plant refuse is to bury it. As with surface refuse piles, these buried wastes can ignite and can also lead to ground and surface water pollution. Steps to ameliorate these problems have been devised over the years. C and K Coal Company, of Clarion, Pa., the largest Pennsylvania surface mining company, has incorporated all of these steps and added of few, of their own in their latest disposal practice. In addition to layering and compacting, C and K practices selective placement and dilution to minimize longterm problems.

Jan 1, 1977

By Nathaniel Arbiter

In contrast to pyrometallurgy's 6000year history in metals production, hydrometallurgy is of relatively recent origin. The earliest reference to it was in the 16th century, with the first applications to copper in the 17th and 18th centuries. In the 19th century, increased demands for pure metal resulted in the development of electrolytic refining, and early in this century electrowinning. The rapid growth in copper production in the 20th century, particularly in the United States and Chile, stimulated the development of new technology for leaching and for the recovery of copper from leach solutions. In the past 25 years, solvent extraction has become a major factor by permitting novel leaching technology that produces dilute or complex solutions. In addition, solvents other than sulfuric acid, and chemical methods for precipitating copper metal are now of increasing interest. These are trends that should grow in importance with the need to process lower grade and more complex materials. The evolution of copper hydrometallurgy is reviewed. Key factors in recent major developments are presented with details of specific operations and with trends for the future indicated. The relative importance of copper hydrometallurgy is compared with that of pyrometallurgy in the light of probable changes in ore supplies and character.

Jan 1, 1994

By Howard J. Haselhuhn

"The effectiveness of reagent adsorption onto hematite ore particle surfaces is critical during beneficiation to promote effective selective flocculation and dispersion and increase iron oxide recovery. The relationship between aqueous calcium in the process water and the effectiveness of common iron ore dispersants has never before been studied. The nature of common dispersants was studied in the presence and absence of calcium in the process water. The settling behavior of hematite-rich iron ore at pH 11 was assessed in the presence of calcium and inorganic dispersants: sodium silicate, sodium tripolyphosphate (STPP), sodium hexametaphosphate (SHMP) and organic dispersant ethylenediamenetetraacetic acid (EDTA). It was found that inorganic dispersants are ineffective at a pH of 11 without activating the surface sites of the ore particles with calcium. Organic dispersants, however, were found to be effective with and without surface site activation.IntroductionThe United States produced 54 million metric tons of concentrated iron ore in 2011 (Jorgenson, 2013). Over 8 Mt were produced using a process known as selective flocculation and dispersion (CCI, 2011). The grade of this ore is slowly depleting, making it imperative that processing efficiency improves. To increase processing efficiency, a complete understanding of the effects of chemical reagents in the process must be acquired. This process relies heavily on dispersants to disperse iron oxides from gangue minerals in settling processes. The mechanism that these dispersants use to disperse the ore and its relationship to calcium in the process water has never been studied. The following extended abstract summarizes the relationship between aqueous calcium in process water and the effectiveness of common iron ore dispersants at dispersing hydrated hematite ore. These tests were carried out at a pH of 11, as this is a typical pH used to ensure dispersion in selective flocculation and dispersion processes."

Jan 1, 2015

By Neil and Associates

Seismic tomography is one of several additions to the suite of geotechnical engineering tools for use in various underground rock and mineral geologic structures. Seismic tomography is a method for reconstructing a cross section of an object based on attributes of seismic energy that have been transmitted through the object. The in-seam seismic tomogram provides a dataset that can be graphically portrayed in a color-coded format that is then used to infer relative stress concentration (Fig. 1). During the past several years, the US Bureau of Mines (USBM) at its Denver, CO and Twin Cities Research Centers in Minnesota funded several innovative hardware and software developments. These were directed toward use of in-seam seismic tomography for underground geologic strata evaluations. These preliminary investigations have matured into well-defined and field-proven technical advances for improving ground-control decision making in the mining industry.

Jan 1, 1996

By C. C. White

Although many notable scientific investigations relating to roof control have been made, roof control still must be considered one of the more baffling problems confronting the miner. Each year contributions are made to our understanding and techniques in dealing with various single phases of the overall problem, however, an equation considering all the variables involved in roof control, if formulated, would indeed be hopelessly complex. Among the factors to be considered is first, gravity which is always acting but which is sometimes less of a problem than lateral forces. There are lateral forces due to expansion, resulting from the weight of overlying rock; to these must be added lateral stresses of orogenic or tectonic orgin, which may be enormous. Stresses due to plastic flow of beds, water pressure, gas pressure, expansion due to absorption of water, faults, joints, fractures, pot heads, and the like may complicate the solution. Therefore, we must base decisions on roof control, and roof bolting in particular, largely on experience, and far too often on few "knowns" and many "unknowns", The development of "in situ" roof trusses may prove of benefit because, they unlike roof bolting, promise positive calculable roof support. These trusses require installation of steel tensioned rods in the roof, which rods are arranged to produce a stress pattern similar to a bridge truss, the roof rock acting to transmit the compression forces. The simplest form of truss (see figure 1) consists merely of two steel rods anchored at the back of holes drilled at an angle of approximately 45° over the pillars, collared near the the middle of the room, the lower ends of the rods being connected together by tierods and turnbuckles. Used in this way, a 3/4" diameter rod can offer greater support than a 10" x 5-3/4" wide flange steel beam. By tightening the turnbuckle, uplist on the roof can be produced,, the downward reaction being transmitted to the pillars by the rods. This simplest form of truss has been used in rooms up to 24' in width. Trusses of four panels, that is, consisting of a truss within a truss, as shown in figure 2, have been used successfully in rooms 30' wide. (figs 2 & 3) It appears a 6 panel truss could be used in a 40, wide room.

Jan 1, 1968

By Ira Sohn

This article revisits global projections made in 1981of eight metallic and fertilizer minerals for the year 2000. The objectives here are to quantify the differences between the projected and observed levels of consumption for the year 2000 for eight of the 26 nonfuel minerals covered in the earlier study. An attempt is then made to attribute these (often) large differences to the major determinants of minerals demand — income, technological, regulatory and other policy changes, and changes in the recycling rates of the metallic minerals. The eight minerals covered are aluminum, copper, iron, mercury, nickel, phosphate rock, potash and tin. This summary article presents the actual population, gross domestic product (GDP) and per capita GDP changes from 1970 to 2000, compared with the projected rates for these important determinants of mineral use, along with the observed growth rates of minerals consumption for the eight nonfuel minerals included in this study. When the projections are compared with the observed global consumption levels for the year 2000, the differences range from +43 percent for nickel to +229 percent for potash.

Jan 1, 2005

By Steve Kral

The timing was right for SME to celebrate its 50th anniversary in February as a member society of AIME. The mining industry is in the midst of a commodities boom that appears to have legs. Not only is the demand for metals, construction materials and the like increasing in developing nations, but developed nations have also seen the demand for those materials increase at impressive rates. So, in addition to networking and seeing old friends, attendees at the SME Annual Meeting and Exhibit in Denver, CO. Feb. 25-28, had several reasons to enjoy the week — a healthy industry and their society’s landmark anniversary. This annual meeting was held jointly with the Colorado Mining Association’s (CMA) 109th National Western Mining Conference.

Jan 1, 2007

By Greg Partington, Darryl Thorburn, Charlene Wildman, Elisa Puccioni, Connie Payne, Campbell McKenzie

"Mineral prospectivity modelling of polymetallic nodule deposits has been completed over the Cook Islands Exclusive Economic Zone (CIEEZ) using the GIS based Weights of Evidence modelling technique. Polymetallic nodules, also known as manganese nodules, have been explored as a possible resource for a number of metals including cobalt since the early 1970s. Recent data on the nodule composition and abundance in the CIEEZ has led to a renewed interest in the prospectivity for manganese nodules in the region. The predictive modelling has used the most recently accepted mineral model for polymetallic deep-sea nodule deposition to identify factors that are most likely to map the presence of this type of mineralisation in the CIEEZ.Manganese nodules form on the deep seafloor as concretions formed by concentric layering of iron and manganese hydroxides around a core and they grow at a very slow rate, on the order of millimeters per million years. The available data for the CIEEZ indicates a greater abundance in the area of nodules formed by hydrogenetic processes, which are the result of slow precipitation of metallic components from seawater. The environment in which the nodules are most abundant is at depths between 4,000 m and 6,000 m in areas of low sedimentation rate. Hydrogenous nodules commonly grow on siliceous and pelagic clay sediment, they are less common on other types of sediment."

Sep 1, 2014

The extraction and processing of minerals from surface mines and quarries can produce significant fugitive emissions as a result of site activities such as blasting, unpaved road haulage, loading, primary crushing and stockpiling. Uncontrolled fugitive dust emissions can present serious environmental, health, safety and operational issues impacting both site personnel and the wider community. Simulation technology is finding increasing use for the purposes of advanced warning of potential problem emissions in addition to providing a basis for future planning applications where demonstrable compliance with regulatory requirements are necessary. The initial re-entrainment and subsequent dispersion of fugitive dust presents a process complicated by the combination of the in pit topography, the surrounding natural topography and the dynamic nature of emissions from these sites. These factors impact upon the accuracy and reliability of the conventional Gaussian plume based computational prediction methods employed for regulatory compliance and IPPC applications. This paper proposes that optimal modelling of open pit emissions may be more accurately achieved by the use of a multi-scale predictive modelling approach utilizing computational fluid dynamics (CFD) methods for high resolution near source dispersion and conventional Gaussian based methods for far field dispersion modeling. This paper presents a numerical based flow and dispersion analysis of a typical UK based open pit utilizing CFD in conjunction with a conventional Gaussian plume based methods. Typical operating emissions and meteorological conditions are obtained from long term data records collected at a large operating quarry extraction operation in the UK. Emissions are modelled using a Lagrangian framework within conventional atmospheric boundary layer (ABL) profiles expressed as functions of turbulence and velocity parameters under assumed neutral conditions. Results are presented in terms of the impact of site topography on in pit retention as compared to the Gaussian based method.

Jan 1, 2009

Coal has been mined in the central Appalachian coalfields of southern West Virginia, western Virginia, and eastern Kentucky for more than a century. The dwindling reserve base consists in large part of coal that would have been considered unmineable by earlier generations. Nearly every current operation is working on a property where coal has been extracted in the past, from seams either above, below, or both. NIOSH is conducting research aimed at helping mine planners prevent hazardous conditions due to multiple seam interactions. To-date, more than 300 case histories have been collected from underground mines, mainly from central Appalachia. This paper focuses on several of the more challenging situations that have been encountered, including: • Room-and-pillar development 20 ft (6 m) beneath full extraction workings at a depth of 1,000 ft (300m) of cover (Virginia) • Pillar recovery 45 ft above full extraction workings at 900 ft (270 m) of cover (Virginia) • Near-simultaneous room-and-pillar mining with pillar recovery with 40 ft (12 m) of interburden and 1,500-2,000 ft (450-600 m) of cover (Kentucky) • Longwall mining directly beneath main entries in overlying seams (West Virginia) • Some of these operations have been highly successful in overcoming the challenges, others less so. The lessons learned from their experience will help ensure that these and similar difficult reserves can be mined safely.

Jan 1, 2006

By A. Robison, V. T. McLemore

"The San Juan Basin, New Mexico contains many heavy mineral beach-placer sandstone deposits of Cretaceous age. Beach-placer sandstone deposits are concentrations of heavy minerals that formed by mechanical concentrations (i.e. settling) of heavy minerals on beaches or in longshore bars in a marginal-marine environment. They have high concentrations of several elements, such as Ti, Zr, rare earth elements (REE), Sc, Y, U, Th, Nb, Ta and Fe. These elements are becoming increasingly more important to industry, because they are used in the manufacture of devices our society uses every day, i.e. cell phones, computers, and alternative energy devices, like solar panels. It is unlikely that any of the beach-placer sandstone deposits in the San Juan Basin will be mined in the near future because of small tonnage, low grades, high iron content, and distance to processing plants and markets. However, as the demand for some of these elements increases because of increased demand and short supplies, the dollar value per ton of ore rises, enhancing deposit economics. Current studies at the New Mexico Bureau of Geology and Mineral Resources are focused on the Apache Mesa (formerly Stinking Lake) deposit near Dulce, New Mexico. INTRODUCTION Beach-placer sandstone deposits are accumulations of heavy, resistant minerals (i.e. high specific gravity) that form on upper regions of beaches or in long-shore bars in a marginal-marine environment. They form by mechanical concentration (i.e. settling) of heavy minerals by the action of waves, currents, and winds (Fig. 1; Bryan et al., 2007). Modern examples are found along the Atlantic Coast, USA (Koch, 1986; Carpenter and Carpenter, 1991), southeastern Australia (Roy, 1999), and Andhra Pradesh, India (Rao et al., 2008), where they are mined for titanium, zircon, and monazite (a Ce-bearing rare earth, REE, mineral). Detrital heavy minerals comprise approximately 50-60% of these sandstones and typically consist of titanite, zircon, magnetite, ilmenite, monazite, apatite, rutile, xenotime, garnet, and allanite, among other minerals. Most of these minerals have a high specific gravity exceeding 4 and are dark colored, giving the sandstones a dark color, resulting in them being called black sandstones. Although beach-placer sandstone deposits are found in strata of all ages; the deposits in the San Juan Basin in New Mexico are restricted to Late Cretaceous rocks belonging to the Gallup, Dalton, Point Lookout, and Pictured Cliffs Sandstones (Fig. 2; Table 1; Chenoweth, 1957; Houston and Murphy, 1970, 1977). The beach-placer sandstones are black, dark gray, to olive-brown, resistant to erosion, and radioactive due to radioactive zircon, monazite, apatite, and thorium minerals. Anomalously high concentrations of Ti, Fe, Nb, Th, U, Zr, Sc, Y, and REE are characteristic of these deposits. Similar Upper Cretaceous heavy mineral, beach-placer sandstone deposits are found throughout Montana, Wyoming, Utah, Arizona, and Colorado (Dow and Batty, 1961; Houston and Murphy, 1970, 1977; Zech et al., 1994)."

Jan 1, 2016

By Angela Binder, Mareike Schubert, Yichen Jiang, Sandra Nowosad, Oliver Langefeld

GermanyINTRODUCTIONThe mining industry is currently characterized by various factors such as environmental impact, resource scarcity, social responsibility and geopolitical uncertainty. The production of minerals required to meet the demand for renewable energy is expected to increase by 500 % by 2050, particularly for critical minerals such as graphite, lithium and cobalt 1. Easily accessible deposits are often depleted, meaning that deeper and more complex deposits need to be developed. Furthermore, investors’ value systems have shifted towards more sustainable practices. Alternative approaches to solving this problem are therefore currently being developed, such as the Modular Mining Systems concept for scalable and adaptable mining projects 2. Many mining companies have also taken important steps to become more sustainable, implementing measures such as proactive closure strategies, restoration programs and the development of renewable energy projects. In the European Union, laws such as the Critical Raw Materials Act and the Net Zero Industry Act support the mining industry 3,4. They see it as important for the energy transition and promote more sustainable ways of working in the industry Particularly negative environmental impacts such as land degradation, scarcity of local water resources, water pollution and greenhouse gas emissions are ingrained in society’s memory. Despite these efforts, the public image has not yet changed. To change this perception, the industry must strive to better communicate its sustainable practices and the steps it is taking towards a more responsible and sustainable future, promote transparency and build trust.Digitalization, automation and electrification are driving the digital transformation in mining. However, their implementation can lead to higher capital expenditure, limiting their adoption across the industry. Furthermore, implementing new technologies can be a daunting task for any organization. Change management comes into play when introducing such disruptive technologies. It involves preparing an organization for change, potential resistance and establishing effective communication. This helps to ensure that the implementation is successful and the benefits of the new technology are maximized. Digital transformation requires well-trained, young mining, electrical, mechatronic and software engineers with a deep understanding of information systems. Unfortunately, the industry faces the enormous challenge of attracting this younger generation, who have little interest in the extraction of raw materials. The need for action is compounded by an aging active workforce heading into retirement and the forecast of increasing demand for critical minerals.In this challenging environment, the concept of Blue Mining with its constant further developments represents a promising approach. This implies a shift from a linear to a sustainably oriented circular economy. For the mining industry, this specifically means the introduction of innovative technologies, the increased recovery of materials from waste and the consistent questioning and application of circular principles along the entire life cycle of a mine. Such a change can not only reduce the environmental impact, but also contribute to economic resilience and increased social acceptance of mining.

Feb 1, 2025

By Karoly (Charles) Kocsis, Kyle A. Scalise

Understanding the climatic conditions in underground mines is necessary for efficient ventilation design, cost savings, and to ensure the health and safety of mine workers. Large volumes of ventilation and climatic data including air volume, barometric pressure, dry bulb temperature, and relative humidity were collected at active underground precious metal mines in Nevada, which allows for the determination of wet bulb temperature and other key parameters. Through the utilization of neural networks, the wet bulb temperature at the bottom of the intake shafts is predicted, while taking into account the “thermal flywheel effect” (TFE). Wet bulb temperature is one of the most important climatic parameters to model and understand because it significantly affects the work conditions and the cooling capacity of the ventilating air. The accurate prediction of the dry bulb and the wet bulb temperatures at the bottom of intake shafts is critical when assessing the climatic conditions in future underground mines and deciding onwhether a cooling system is needed to assure adequate working conditions throughout themine. By utilizing accurate predictions of wet bulb temperatures and other climatic parameters, mine personnel will be safer as reported by Bluhm et al. (2003), and a more accurate ventilation design can be achieved resulting in major cost savings for underground mines.

Mar 3, 2021