Search Documents

By Thomas Marcher

Stanford Linear Accelerator Center (SLAC) is located in Menlo Park, CA. In order to allow for enhanced experiments, the current facilities required expansion. Tunnels were excavated through very weak sedimentary rock interspersed with uncemented zones (Ladera Sandstone) employing the principles of the NATM. The overburden var-ied from 10 to 80 feet. The paper addresses the characterization of Ladera Sandstone that can exhibit the properties of dense sand and weak rock. The paper focuses on the challenges that were encountered during the NATM initial support design and the construction phase including the geotechnical instrumentation, monitoring and design verification process in particular the excavation of the junction between access tunnel and the FEH cavern (49 ft wide by 32 ft high).

By Shuangchun Yang, Le Tong, Ronggui Fan, Cunlei Li

Acid mine drainage (AMD) is difficult to treat due to its physicochemical characteristics, such as high pH and high heavy metal concentrations, so it causes great harm to the environment and human health. If acid mine drainage is discharged arbitrarily without treatment, it will lead to a series of environmental problems and cause long-term environmental pollution. In this paper, the source and hazards of acid mine drainage are introduced in detail. And the principle, the mechanism, the application, and basic information of the current primary technology of the treatment for acid mine drainage are comprehensively introduced and summarized. The summarized treatment technologies for acid mine drainage mainly include neutralization, sulfidization, constructed wetland method, adsorption method, microbiological method, ion exchange method, membrane technology, and microbial fuel cell technology. Also, the primary technology of treatment for acid mine drainage is systematically compared and evaluated. Moreover, some suggestions on the development direction of water treatment technology in the future are put forward. This paper provides a scientific reference for scientific and technical works to treat acid mine drainage.

Sep 4, 2020

By J. Jonas, J. M. Harrington, K. Wangerud, S. D. Fundingsland, J. G. Harrington

EPA NRMRL Mine Waste Technology Program and Region VIII Superfund office are jointly conducting an in-situ technology demonstration at the Anchor Hill Pit Lake, Gilt Edge Mine Superfund site. The goal is to develop in-situ treatment cost/performance data for potential application in long-term water treatment/management at Gilt Edge and similar sites. The pit contained 77,000,000 gallons of pH 3water with elevated metals, sulfate, and nitrate. The Green World Science® patented process for in situ treatment was implemented to isolate and sequester metals; create stable long-term water quality and restore a sustainable ecosystem. COCs have decreased more than 99%, and dissolved discharge standards were attained.

Jan 1, 2004

By Colin Rawlings, Simon Pepper, Maria Karakitsiou, John Mathews, Peter Townsend, Russell Bowler, David Keeble, Christopher Darton, Scott Sadler

National Grid needs to maintain a connection between two existing electricity sub-stations (Beddington & Rowdown) in the Croydon (south London) area, and allow the replacement of two 275 kV cable circuits that are buried under roads. This is to be achieved using a single 400 kV cable circuit within a 10 km (6.25 mile) long, 3 m (9.8 ft) diameter high voltage cable tunnel which is being driven through water bearing Chalk, at depths ranging from 5 m (15 ft) to 80 m (262 ft), with four access shafts(12.5 m (41 ft) in diameter) ranging in depth from 10 m (31 ft) to 40 m (131 ft). The Chalk in this area acts as a source of public drinking water supply (PWS) and is protected by areas designated Groundwater Source Protection Zones. To minimise the groundwater risk the design and construction of the cable tunnel and shafts has paid particular attention to the construction materials used, including testing of these construction materials prior to use, developing construction methods (including the design of the Earth Pressure Balance TBM) and maintaining a groundwater monitoring & testing programme prior to and during construction to ensure the integrity of the Chalk aquifer is maintained as a drinking water source. This paper describes the tunnel &shaft design and construction in relation to these particular groundwater environmental issues which set new precedents for tunnel assessment, design and construction requirements in the United Kingdom.

Jan 1, 2007

By X. Shi

This paper presents design and implementation details of a fuzzy-behavior-based controller for an automated excavator. The robotic excavator is equipped with sensors, actuators and an embedded control system. The excavator controller uses neural-networks to interpret forces and torques gathered during the excavation process from bucket-mounted force sensors. Implementation details card experimental results using the fuzzy-behavior-based excavation controller are given for several excavation tasks. These excavation tasks demonstrate some of the complex skills that are essential for an autonomous mining-excavator controller.

Jan 1, 1997

By J. N. Hartley

Uranium mill tailings, waste products of uranium extraction, contain hazardous constituents that if released into the atmosphere and groundwater could threaten our health and environment. To provide for safe disposal and control of these tailings, Congress enacted the Uranium Mill Tailings Radiation Control Act of 1978 (Public Law 95-604). Subsequently, the Environmental Protection Agency (EPA) established standards for tailings disposal that limit radon emission into the air to 20 pCi m-2s-1 on an annual average basis (EPA 1983). The design life of the impoundment is to be 1000 years where practicable, but 200 years at least. To facilitate the design of containment systems that will meet the EPA standards, the Nuclear Regulatory Commission (NRC) and the Department of Energy (DOE) are sponsoring research at the Pacific Northwest Laboratory (PNL)* to develop the necessary technology. Earthen and asphalt materials have been evaluated for use as radon barriers (Hartley 1983) and as liners to minimize leaching (Buelt 1983). Herbicide and rock barriers against biological intrusion have been evaluated (Cline 1982). Surface stabilization techniques have been investigated to maintain the long-term effectiveness of a containment system that must be protected from wind and water erosion, chemical and physical degradation, and biological disturbance.

Jan 1, 1984

By Jamal Rostami, Ebrahim Farrokh

Selection of tunneling method, specially the use of shielded machines for application in deep rock tunnels can be heavily impacted by presence of ground convergence and squeezing conditions. Tunnel convergence is a function of ground conditions (i.e., rock mass behavior, groundwater, in-situ stresses), size of the opening, and TBM operational parameters. The case study of Ghomroud water conveyance tunnel project in Central Iran, which is under construction using a double shield TBM, is used to examine the effect of rock parameters on tunnel convergence and hence on the need for over excavation and shield lubrication to avoid problems with the shield getting stuck. Although it is impractical to perform a continuous assessment of rock mass conditions within the shield or in the lined tunnel, results of field observations and subsequent studies show that the amount of the tunnel convergence has direct correlation with the percentage of fines and large rock fragments in the muck and TBM thrust/torque/ROP. These relationships have been examined and will be presented in this paper.

Jan 1, 2007

By A. Sobhy

Froth flotation is a widely used, cost effective coal cleaning process. However, its high process efficiency is limited to a narrow particle size range between approximately 50 to 600 µm for coal and 10 to 100 µm for minerals. Beyond this range, the efficiency of froth flotation decreases sharply, especially for difficult-to-float coal fines of weak hydrophobicity (e.g., oxidized coal). This study was aimed at enhancing recovery of an Illinois fine coal sample using a flotation column featuring a hydrodynamic cavitation nanobubble generator. Nanobubbles that are mostly smaller than 1 µm can be formed selectively on hydrophobic coal particles from dissolved air in fine coal slurry. Results indicate that combustible recovery of a -150 µm coal was increased by 5-50% for different size fractions in presence of nanobubbles, depending on process operating conditions. Other major advantages of the nanobubble flotation process include lower collector dosage and air consumption since nanobubbles are produced from air naturally dissolved in water and they act as a secondary collector on particle surfaces, thereby resulting in considerably lower operating costs. Key words: Cavitation; coal; froth flotation; nanobubble.

Feb 27, 2013

By John B. Spencer

Earlier this year, Simplot Phosphates achieved a safety milestone at its Vernal, UT phosphate operations. In March, the entire operation reached achieved seven years without a lost time accident. And the mine operations at Vernal reached the 1 million hours benchmark without a lost time accident. This million hour achievement has been 19 years in the making. This achievement reflects the mine’s strong attitude towards safety, the company said. Safety is an integral part of its culture and requires diligence and considerable work. Attention to even the smallest of details cannot be allowed to slip. This is a record Simplot Phosphates said it hopes to improve on every day.

Jan 1, 2004

By H. A. Taylor

Graphite is elemental carbon that crystallizes in the hexagonal system as six-sided platelets. It occurs naturally and is mined. And it can be made artificially from petroleum coke in the form of shapes (electrodes) and powders. The market for most kinds of graphite in most end-uses was good in 2004. The 2005 graphite market looks positive. The major graphite prices, as given in Industrial Minerals, remained unchanged throughout the year. The preliminary 2004 U.S. Geological Survey (USGS) prices for natural graphite showed almost no change for crystalline flake. They were $600/t ($544/st) in 2004 and$622/t ($564/st) in 2003. Mexican amorphous graphite was almost unchanged at $150/t ($136/st) in 2004 from$152/t ($138/st) in 2003.

Jan 1, 2005

By R. P. Proulx

The Meikle Mine is a high grade, underground goldmine utilizing primary-secondary longhole open stoping with delayed backfill to produce 2700 tpd(3000 stpd) of ore. Hot and reactive ground conditions were encountered early on in the mine life. Ground temperatures up to 166°C (330°F) were measured. In the early stages of mining, the mine experienced premature detonations using different explosive products. The learning curve to safely mine this high-grade gold deposit in hot and severely reactive ground was indeed very steep. Currently, the Meikle Mine uses a special buffered bulk emulsion in all blasts to address hot and reactive ground concerns. In addition, exacting procedures are also followed to ensure safe work with explosives. The combination of new explosives technology and strict loading procedures permits high mine productivity with the highest degree of safety.

Jan 1, 2000

By L. Alan Weakly

The U.S. Department of Energy (DOE) has entered into a $l.5 million Cooperative Agreement with Alpine Equipment Corporation/Astro International Corporation ("Alpine") of State College, Pennsylvania, for the evaluation of water-jet-assisted (WJA) mechanical cutting of oil shale under actual mining conditions. A commercial-sized, heavy WJA mechanical miner is being assembled based upon the successful "factory testing" of a smaller prototype miner utilizing standard tungsten-carbide and Polycrystalline Diamond Composite (POC) bits in large oil shale boulders. Actual field testing of the machine will be conducted in an oil shale mine located in the Piceance Basin of Western Colorado. In-mine logistical support is being provided by several oil shale companies through the Colorado Mining Association (CMA) and the U.S. Bureau of Mines (USBM).

Jan 1, 1990

By Stephen Hodgson, Ken Brouwer

September 2005, Northern Dynasty Mines announced the discovery of a new, high-grade deposit at its Pebble project in southwest Alaska. The product of insightful geological investigation, Pebble East, as it is now known, is quickly growing into one of the most significant copper deposits in the world. Preliminary analysis shows it could reduce the U.S. copper supply deficit by a third. The new deposit has also altered Northern Dynasty’s view of how Pebble should be developed. This article describes the Pebble project as it is currently understood and outlines the work planned for the next several years.

Jan 1, 2007

By Eric M. Hill, Daniel E. Walsh, Hsing K. Lin, John T. Hollow

The Fort Knox Mine is located in Alaska’s interior where the average ambient air temperatures range from -24°C in January to 16°C in July. The mill processes a free milling gold ore utilizing both a gravity recovery circuit and conventional cyanide leach/carbon-in-pulp circuits. Plant slurry temperature cycles seasonally and allows for a unique opportunity to measure the impact temperature has on gold leach kinetics, carbon adsorption efficiency and cyanide destruction reactions. Mathematical models have been developed to accurately predict actual mill performance. This paper describes the development of the models and presents data that allow for a better understanding of the impact of circuit operating temperature on process efficiencies.

Jan 1, 2005

By K. Shoji

Residence time distributions (RTDs) were estimated by water tracing in a number of wet overflow ball mills (diameters 0.38 to 4.65 m) producing dense, coal-water slurries. In open-circuit mills of 0.38 m diameter and various length-diameter (L/D) ratios, the mean residence times of solid were also determined from measured mill holdups. Holdup increased with increased mill feed rate, but the mean residence times of coal and water were still equal to each other. The experimental residence time distributions were fitted to the Mori-Jimbo-Yamazaki semi-infinite, axial mixing model, and the dimensionless mixing coefficient was determined for each of 25 tests in single- and two-compartment mills. This coefficient was found to be independent of the feed rate but linearly proportional to the D/L ratio. The mixing coefficient was smaller for two-compartment mills than for single-compartment mills, showing that there was reduced mixing introduced by the diaphragm separating the compartments. Equations are given to scale residence time distributions for changes in mill diameter and length.

Jan 1, 2008

By Chris Bennett, Drupad Desai, Kirit Mevawala

INTRODUCTION The design/build (D/B) philosophy of contract delivery is neither new nor unusual when it comes to at-grade, elevated or high-rise structures. But when it comes to constructing underground facilities, there were no examples to be followed in early 90sin the continental United States or its territories. When DMJM+HARRIS was selected as general architectural and engineering consultant for the Tren Urbano (TU) project in Puerto Rico, one of the requirements of the Federal Transit Administration (FTA) for funding commitment was to use TU as a demonstration project utilizing design/build contract delivery method. Now fifteen years later, New York City Transit (NYCT) has instituted a similar requirement for their first Tunnel Boring Machine (TBM) contract for the Second Avenue Subway. As with most construction mega-projects, lots of things have happened and there were several lessons learned from the TU experience that are now being applied to Second Avenue. Both of these projects require building tunnels and underground transit facilities in heavily traveled corridors of an urban city, in the vicinity of active business and commercial enterprises. To enhance the challenge, there are noise and vibration sensitive and historic urban receptors either over or along both the transit corridors. Column free Tren Urbano station caverns over18 m (60 ft.) wide were built in soft ground conditions within 3.6 m (12 ft.) of the surface under an aging heavy utility corridor, while NYCT tunnels with station structures stretching the limits of rock caverns to 34.8 m (100 ft.), were planned in rocky geology with the presence of shear and fault zones and some mixed face conditions. BACKGROUND During the early period of design/build experimentation, the speed with which the contract procurement packages could be put together enabled the owners to take advantage of the major efforts underway to rebuild the infrastructure that was suffering from post-World War II neglect. Use of design/build for new starts was unheard of and most of the projects were smaller in nature in order to allow the methodology to be tested. Development of functional design packages with the understanding that the D/B

Jan 1, 2005

By Shawn Collins

BACKGROUND The history of the Pine Point Mine is a rich one. This property once boasted one of the largest and most profitable lead-zinc mines in Canada's long and storied mining history. The Pine Point mine used open pit technology to extract the ore, but they faced several challenges. In addition to logistics problems with haul distances and metal prices, the mine faced the challenge of a large in flow of water from the Great Slave Lake. Eventually, the Pine Point Mine was closed leaving behind a large deposit of lead-zinc ore. Following the closing of the Pint Point Mine, Tamerlane Ventures Inc. acquired this property which includes approximately 70 million tonnes of lead-zinc reserves. The initial phase of this project will concentrate on the R-190 deposit as a test site to prove their new approach for extracting the ore. The R-190 reserve is believed to have approximately 1,014,000 million tonnes of high grade ore varying from 5% to 52% combined lead-zinc. Once the pilot project proves the approach is valid, the process will be repeated in approximately 33 other ore bodies on the property. This paper is written to discuss the design process to determine the most effective means of placing production and service equipment in the same shaft. Currently the design work and the mining scheme is complete, but lead-zinc pricing has prevented Tamerlane Ventures Inc. from moving forward with the project.

By H. Takamoto, M. Ichinose

"The basic objectives of mine roadways are to provide sufficient cross sections in order to meet the needs of accommodation of equipment, transport, personnel travel and ventilation. However, many roadways become damaged to the extent of needing maintenance, generally dinting, and in some cases requiring re-ripping. The damaging of a roadway is a result of several factors including geological properties of surrounding strata, method of roadway formation, support systems and so on. Among these factors, strata conditions play important effects on the stability of roadways and other mining activities. Weak rocks cause excessive roadway closures, and water softens some rocks and worsens the closure problem. In Indonesia, over 250 Mt of coal is now produced from almost surface mines. In the near future, some coal must be mined from underground. Unfortunately, the mechanical properties of coal measures rocks are not so good to open underground mines. In this paper, a scientific discussion on the effect of water on the stability of roadways is given on the basis of results obtained by means of in-situ investigation and laboratory tests both in Japan and Indonesia."

Jan 1, 2011

By S. C. Tadolini

Roof support systems have evolved from standing posts and timbers to a generation termed ?big nails? where steel bars are inserted into boreholes and anchored with expansion shells and/or resin cartridges. These systems have been effective but are limited to mining height. Additionally, the properties of steel do not resists shear forces or have the flexibility being required in difficult ground conditions. The next generation of roof support systems is coupling the best parts of the ?big nail? and resin grouted cable bolt systems. This paper will present the advanced technical solutions of the next generation of cable systems that includes an indented high-capacity PC-strand used with a variety of fixtures. Case histories of support applications will be presented.

Jan 1, 2012

By John H. Raymer

Groundwater inflow into hard rock tunnels is strongly affected by recharge and drawdown of the water table. Previous analytical and empirical methods for estimating inflow have generally not accounted for these factors in an accurate or systematic way, resulting is wrong conclusions about inflow and the effects of the tunnel on the surrounding environment. This paper discusses these issues and provides some simple analytical equations to estimate inflow and water table drawdown around the tunnel. Examples from tunnels in the Atlanta area are provided.

Jan 1, 2005