Search Documents

By Noel N. Moebs

The Bureau of Mines measured surface subsidence above four small coal mine room-and-pillar sections in southwestern Pennsylvania, to obtain preliminary information on the magnitude and character of selected parameters, such as angle of draw and maximum subsidence, which are essential to the development of subsidence prediction methods. Data varied widely at the four sites; this is attributed to local geologic and mining conditions. Surface deformation at each site was of a magnitude normally associated with severe structural damage.

Jan 1, 1982

The National Institute for Occupational Safety and Health (NIOSH) recommends that occupational exposures to respirable coal mine dust and respirable crystalline silica* be controlled by complying with the provisions presented in this document. These recommendations are designed to protect the health and provide for the safety of workers exposed to respirable coal mine dust and respirable crystalline silica for up to 10 hr/day during a 40-hr workweek over a working lifetime. The information presented in this document demonstrates that underground and surface coal miners are at risk of developing simple coal workers' pneumoconiosis (CWP), progressive massive fibrosis (PMF), silicosis, and chronic obstructive pulmonary disease (COPD). Adherence to the recommendations in this document should prevent or greatly reduce the risk of adverse health effects in workers exposed to respirable coal mine dust and respirable crystalline silica. NIOSH recommends that preventive efforts be focused primarily on reducing worker exposures. Effective health and hazard surveillance and medical screening are also useful components of a comprehensive prevention effort.

Jan 1, 1997

By Charles L. Kimbell

The concept of data availability must be addressed, because there are perceptible changes from year to year, and the availability of accurately reported, precisely defined statistics and nonstatistical information provides the only sound basis for analytical studies required for government policy planning or industry market analysis. As the countries of Eastern Europe and the former U.S.S.R. undergo the transition from centrally planned economies to market economies, there has been a perceptible increase in information availability for rather obvious reasons. Any industrial operation seeking economic assistance from Government and/or private sources outside the country in which the facility is sited must provide some appraisal of its operations at the time it seeks assistance, as well as some information on previous performance to serve as tools in evaluating its potential under the proposed development scheme for which it seeks financial assistance. Additionally, there was growing governmental recognition that concealment of much of the national mineral production, trade, and consumption data for purposes of national military and/or economic security probably never was very successful, never was really necessary for most commodities, and certainly proved unnecessary with the end of the so-called cold war. Indeed, the long-term unwillingness to publish uniform statistical series of reliable,

Jan 1, 1993

Lower the respirable dust exposure of longwall shearer operators by keeping the dust cloud confined to the face. Approach Change the location of face-side machine cooling, water sprays. How It Works The dust breathed by the longwall shearer operator is usually produced by the shearer itself. The dust cloud originates at the face, and the exposure of the operator depends largely on how quickly this cloud spreads into the walkway. Water sprays on the shearer body can have a large effect on dust cloud spreading. Results to date indicate that sprays can help confine the dust cloud to the face if they are carefully placed. Otherwise they can make dust levels far worse. The worst offenders are often face-side sprays used to discharge cooling water from the cooling jackets of the shearer motors. These face-side sprays set up an air circulation pattern as illustrated in the drawing. Air induced by the sprays to flow towards the face, raises the air pressure in front of the face, which causes the air flow to turn and then move back over the shearer, bringing dust with it into the walkway.

Jan 1, 1981

By M. A. Trevits, S. W. Lambert

In this Bureau of Mines investigation, production was monitored for 1 year at over 30 coalbed gas-drainage boreholes located in Alabama, Pennsylvania, and West Virginia. Results indicate that the quality of data gathered from such wells can be improved greatly if potential problems are anticipated and prevented in the early stages of well production. Major water-monitoring problems include solids buildup, freezing, the presence of gas in surface waterlines, and improper pumping interval settings. Such problems may be avoided by incorporating in the original well design waterline filters, sand screens, separator tanks, and systems to automatically control pumping intervals. Problems related to measurement of coalbed gas flow include large quantities of water vapor contained in the gas, especially during winter months; freezing and subsequent obstruction of flow; sudden, uncontrolled release of gas pressure; and solids buildup in metering equipment. The installation of commercially available items, such as filters, separators, and insulation, and the thoughtful application of a basic knowledge of coalbed gas reservoir characteristics will prevent most production-monitoring problems.

Jan 1, 1978

By William H. Schiffbauer

This paper details the computer hardware and software integrated to provide computer-assisted control and monitoring of four different coal mining machines. The backbone of each system is a U. S. Bureau of Mines integrated distributed microcomputer control network called BOM/NET. The network provides connections for intelligent sensors and systems that provide for navigation, diagnostics, and computer control. Many different computer systems using various operating systems (including RMX I, UNIX, VXWORKS, DOS and DCX51) have been connected to the network and each have had complete network functionality. A description of the network's integration to Joy' 16CM, a Joy 14CM, a Jeffrey 102, continuous mining machines, and a custom built auger machine is provided. The networks for the Joy 16CM, the Joy 14CM, and the Jeffrey 102 have been installed and extensively tested at the Bureau's surface test facility. The Jeffrey 102 system has also been tested in a highwall coal seam. The Joy 14CM will soon be tested underground.

Minimize airborne respirable quartz dust produced by continous mining machines. Approach Install a shovel-mounted underboom water spray system on the off-curtain side of the mining machine. Dusty air containing quartz is momentarily trapped under the boom, where it is captured by fine spray mist. The remaining dust cloud is directed immediately behind the curtain before it can migrate back to the machine operator's location. How It Works Previous studies have shown that most of the dust generated by continous mining machines occurs under the boon as the cutter head shears down. The primary source of respirable quartz dust on many continous mining operations is cutting or trimming roof rock immediately prior to shearing. This results in very high concentration , of

Jan 1, 1989

By M. C. Chapman, E. C. Westman, A. T. Iannacchione

Examination of seismic records during the time interval of the Sago Mine disaster in 2006 revealed a small amplitude signal possibly associated with an event in the mine. More needs to be understood about the seismicity from mine explosions in order to properly interpret critical seismic information. A seismic monitoring system located at NIOSH’s Lake Lynn Experimental Mine has monitored experimental gas and dust based explosions and impact tests. The seismic signatures from these different events were analyzed using standard waveform analysis procedures. The magnitude of seismic energy during a gas and dust explosion was found to be more dependent on mine entry geometry and seal behavior rather than on the amount of explosive fuel present. The results suggest a large explosion that’s not restricted can generate potentially the same magnitude as a small explosion that is restricted.

Measure the leakage through individual crosscut stoppings quickly and economically so that the worst ones can be identified and repaired. (Typically 60 to 80% of the air supplied to a mine short circuits before reaching a working face.) Approach Most of the leakage through a permanent stop-ping is channeled through two windows in a temporary stopping, and air velocities through the windows are measured; leakage is determined from a formula. How It Works A temporary stopping made of plastic brattice is erected in the same cross cut as the permanent stopping, either upstream or downstream. The brattice is fastened to the roof, bottom, and ribs of the entry with spads. Normal leakage of brattice was allowed for in deriving formula, and does not effect results. For best accuracy the brattice and the stopping should be separated by a distance of one hydraulic diameter.

Jan 1, 1979

By C. Q. Cupps

Rate of gas diffusion in reservoir oil has been investigated in an effort to explain the variation in oil characteristics observed in the Weber Sandstone reservoir, Rangely field, Colorado. Coefficients of gas diffusion were determined experimentally for the Rangely oil system and used in a mathematical simulation of gas diffusion during the probable life of the Rangely reservoir, estimated at 65 million years. The simulator involved solution of Fick's law for diffusion in two dimensions by the method of finite difference and successive over-relaxation. The results show that continuing gas diffusion is a logical explanation for the variation in oil characteristics at Rangely and that the pattern of gas distribution by diffusion in an asymmetrical reservoir will not conform to structural contours as originally proposed.

Jan 1, 1971

Compare the dust control efficiency and bit life of surface coal mine drills using standard water injection and water injection with water separation. Approach A research study was conducted to determine if a water separation technique affects wet suppression dust control. Dust control efficiency and bit life of surface coal mine drills were compared during tests using both standard water injection (wet drill bit cutting) and water injection with water separation (dry drill bit cutting). Background Surface coal mine blast hole drills typically generate a substantial amount of dust during the drilling cycle. One method used to control this dust is the injection of water into the bailing air. This is known as wet suppression.

Jan 1, 1988

Coal miners, especially roof bolter and continuous miner operators, work in a hazardous underground environment where they are often exposed to poor roof conditions. Nearly 500 rock fall injuries are reported each year, and 99% of them are caused by rocks falling from between the roof bolts. These loose rocks that injure miners are usually just a few inches thick, but on average weigh 280 pounds. NIOSH has found that most rock fall injuries can be prevented by installing roof screen during the bolting cycle. Roof screen is a sheet made of steel wires in a grid pattern. When screen is bolted up against the mine roof, it provides far more coverage than any common surface control used in the mines today. Because more mine roof is covered, there is less chance that a rock will fall and injure a miner. The facts about roof screen are shown in the new NIOSH video entitled “Make It Safer With Roof Screen.” Using extensive underground footage, the 7-minute video shows how well screen keeps loose rock from falling in difficult roof conditions. Techniques for installing screen from both outside-controlled and walk-thru roof bolting machines are shown. The video also provides safe handling tips, best practices, and information about machine technology that can greatly improve material handling. Throughout the video, a coal mine safety manager and a shift foreman talk about the tremendous difference that roof screen has made at their mines. An instructional booklet supplements the video with additional information. It presents compelling data from mines that have practically eliminated rock fall injuries with a roof screening program. Other sections of the booklet discuss in greater detail roof screen installation, tips for manual screen handling, a material handling system for roof screen, and use of the personal bolter screen, which can be easily handled by one person. Screen specification and custom ordering are described, including the sizes of screen, grid sizes, reinforcing (indicator) wires, edge cut options, and screen strength. A list of additional sources of information is also provided. Nearly every mine eventually encounters poor roof. Screen is one of the most powerful control techniques available. This new video will help make mine managers aware of screen, and it can help them in developing a roof screen installation program. It also serves as an information source and teaching tool for safety managers and trainers. The video can easily be integrated into new miner training programs or annual refresher training.

Mar 1, 2005

By A. V. Petty

In accordance with its objective to maximize minerals recovery from secondary domestic resources, Bureau of Mines conducted research on recycling chrome refractory wastes. Since 20 pct of the U.S. demand for imported chromite is used in the production of refractories, primarily for the steel, copper, and glass industries, samples of used chrome-containing refractories from copper converter and reverberatory furnaces were investigated to determine their potential for recycling. The samples were beneficiated using a combination of wet magnetic separation, flotation, and leaching techniques, and the concentrates were reformed into briquets for refractory evaluation. Small refractory test specimens produced from the beneficiated concentrates gave modulus of rupture values at 1,350° C comparable to those of commercial mag-chrome brick of similar composition; however, grinding the waste refractories to at least minus 65-mesh was required in order to liberate the metallic copper. Most of the copper was easily recovered using conventional beneficiation techniques, but the finely ground chrome concentrate would require briquetting, calcining, and crushing to produce a coarse grain suitable for recycling into secondary mag-chrome refractories.

Jan 1, 1981

Develop methods to detect and repair poorly functioning dust collectors on roof bolters. Approach In conjunction with a research project to reduce silica dust in coal mines, a variety of roof bolting machines operating under different conditions were examined to find out how much these machines were contributing to the silica dust problem. Results The investigation concluded that if the bolting machines' dust collector is properly maintained, very little dust can be measured in the air, even with minimal airflow over the bolter. Poor maintenance, however, frequently results in high dust levels. Three major problem areas were found. These were: (1) filter leaks, which allowed dust to escape, (2) accumulations of dust in the collection system, and (3) low airflow at the bit due to hose, fitting, and relief valve leaks.

Jan 1, 1984

Determine the site specific flow behavior of leachants and groundwater during development, production, and restoration phases of an in situ leaching operation. Approach A computer program has been developed which simulates the hydrologic activity associated with in situ mining. Various user options enable modeling of many of the site specific geologic conditions and well field specifications that affect the hydrology of solution mining. How It Works In situ hydrology is modeled, using a closed-form solution to the three-dimensional, partial differential equation that describes changes in hydraulic head as a result of pumping from leachant Injection and recovery wells. Model capabilities include arbitrary well patterns and pumping schedules, partially penetrating well screens, directionally anisotropic permeability and natural groundwater flow, in either

Jan 1, 1981

To develop a simple device for rapidly determining the shearing strength and angle of Internal friction of coal and rock in situ. Approach Use a portable, permissible, hydraulically operated device in boreholes as deep as 100 feet into the rib, floor, or roof of the mine. How it Works The device, called a Borehole Shear Strength Tester (BST), is inserted Into a 3-inch-diameter borehole to the desired depth, locked Into position, and activated to shear the rock or coal in the borehole walls. The normal and shear pressures exerted by the BST, which are recorded during the test, are used to calculate the shearing strength and the angle of internal friction. The BST consists of 3 main components and several minor components. Main components are: ? A shear head with 2 shear plates that bite into the rock when normal pressure is applied. ? A hollow hydraulic jack with RW drill rods that pull the shear head when shear pressure is applied. ? A console with a hand pump and two hydraulic gages to activate the device and to indicate the pressures that apply the normal and shear faces to the shearing plates.

Jan 1, 1981

Eliminate the occurrence of false fire detection alarms caused by the operation of diesel-powered vehicles in underground coal mines. Approach Fire detection systems used in underground mines are based on measurements of airborne combustion products such as carbon monoxide or smoke particles. The effectiveness and credibility of these systems can be reduced by the occurrence of false alarms that result from the operation of diesel-powered equipment, which produces the same combustion products. False alarms end up being very costly to the mine operation in terms of downtime and labor needed for verification. To improve upon current fire detection systems used in the presence of internal combustion engine products, the U.S. Bureau of Mines developed a fire detector that can discriminate between the occurrence of real mine fires and the presence of engine smoke.

Jan 1, 1989

By Steve Iverson, Jeffrey C. Johnson, Henry Rodriguez, Rene Rodriguez, Michael Lhamond

To reduce fatalities resulting from personnel falling into voids formed above feeders in coal piles, the National Institute for Occupational Safety and Health at the Spokane Research Laboratory established a project to monitor coal surge piles to detect the formation of voids. A resistivity imaging method has been developed by GECOH Exploration, of Lexington, KY, in which a geophysical technique known as vertical electrical sounding (VES) is used to scan for these voids. VES operates by measuring the electrical field produced by a current in the ground at the bottom of the coal pile. This paper summarizes the results obtained from a field-scale test and shows that mapping voids within a coal pile is possible.

By J. Torma-Krajewski, M. Lehman

In 2005, NIOSH and Badger Mining Corporation entered a partnership to implement ergonomic interventions, including a systematic process, to address exposures to risk factors that may result in musculoskeletal disorders or other types of injuries/illnesses. As a result of this partnership, an ergonomics process was integrated with the existing safety and health program to promote an on-going application of ergonomic principles, and over 40 task-specific interventions were implemented during the first year of the process. This paper presents details of the process integration, and several examples of task-specific interventions that reduced exposures to risk factors.

To more rapidly and economically prepare solutions for chemical analysis, of a wide range of ores, slags, minerals, and metals. Approach A Simple pressure-dissolution system was devised using an inexpensive, heavy wall plastic bottle containing a sample in an acid medium. Using the technique, a complex silicate sample can be dissolved in less than 1 hour. How It Works A weighed portion of a sample, ground to minus 100-mesh, is placed into a polycarbonate or polysulfone plastic bottle. A mixture of hydrochloric acid, nitric acid, and hydrofluoric acid then is added. The bottle threads are wrapped with a layer of Teflon tape to prevent leakage, and the bottle cap is screwed on tightly. The sealed bottle is placed in a balling water bath. In the hot water, the plastic bottle acts as a pressure vessel to contain the pressure generated inside it. This technique should only be used by trained experienced people who are familiar with the hazards of hot acids under pressure. After being cooled in cold water, the resulting solution is brought to the final volume by adding 1.5 weight-percent boric acid solution to the bottle. The cap is replaced, and the bottle and solution is reheated. Precipitated fluorides, as well as any residue, are dissolved by the fluoride-boric acid reaction. The resulting clear solution then is suitable for spectro-photometric examination or other analysis.

Jan 1, 1980