Search Documents

By Steven J. Page

Overexposure to airborne respirable crystalline silica dust can cause disabling or fatal respiratory disease, and mine worker exposure to silica dust continues to be an ongoing occupational health concern. Exposures of surface coal mine rock drillers to respirable crystalline silica are of particular concern. On surface coal mine drills, bailing air flushes the cuttings out of the drill hole. Conveyor belting material is typically used to fabricate a shroud around the drill deck in an effort to contain the drill dust so that it can be captured by a collector. Dust leakage from the drill shroud is usually the worst dust source problem on most drills. The focus of this work is drill shroud dust leakage and the relationships of various drill parameters on this leakage. Experimental data were obtained and used in combination with dimensional analysis to establish these relationships. In general, it is found that airborne respirable dust (ARD) concentrations vary in a direct relationship with shroud leakage area and in an inverse relationship with drill deck cross sectional area and shroud height. This work expands the testing and dimensional analysis previously reported for collector/bailing air flow ratios ranging from 2:1 to 4:1 to include ratios approaching 1:1. A semi empirical mathematical model has been developed and expanded to describe ARD generation on surface coal mine drills. Geometric parameters included are drill deck height and cross sectional area, shroud leakage associated with the deck shroud, and the operational parameters of bailing airflow and dust collector airflow. The relationships can be described by logarithmic functions and yield predictive ARD values, which fall in the range measured on operating drills for collector/bailing air flow ratios greater than 2. However, at values of collector/bailing air flow ratios of approximately 1.1, the amount of ARD shows minimal response, if any, to drill deck shroud improvements that do not result in near perfect seals. This is a condition that can occur in actual operation and is a substantially different result than previously expected and reported. Application of these results should provide mine operators with sufficient information to determine (1) the relative magnitude of their dust emissions, (2) where they should focus their efforts to reduce ARD emissions and (3) the improvement they could reasonably expect to achieve. Given that exposures of surface coal mine rock drillers to respirable crystalline silica are of particular concern, substantial reductions of airborne silica dust during drilling may be estimated and achieved through use of the analysis presented. Keywords: drill; dust; model; dimensional analysis

Jan 1, 2008

By S. McGinn, G. Schnakenberg, D. Petrie, A. Bugarski, M. Grenier

As part of the Diesel Emissions Evaluation Program (DEEP) consortium, Noranda Inc. has undertaken a field project to evaluate the overall performance of the latest diesel particulate filter technology (DPF) at its Brunswick Mine in Bathurst, New Brunswick. Performance of the filtration systems is evaluated with respect to their ability to reduce tailpipe emissions and concentrations of diesel particulate matter (DPM) and noxious gases in mine air, efficiency of filter regeneration process, maintenance requirements, reliability, and acceptance. Four different particulate filter systems deployed on heavy production vehicles are subjected to an 18-month field evaluation. Over the evaluation period the vehicles will have accumulated approximately 4000 operating hours in production. This paper presents the results of testing conducted mid way through the 18-month field trials. The 400- meter section of the mine drift at 525-5 sub level, hereinafter referred to as the "isolated zone" was isolated between intake and exhaust fan systems and sealed with bulkheads against leakage. The isolated zone was ventilated at the rate required per CSA Standards and issued by CANMET for the engines tested. Four vehicles, two load-haul-dumps (LHDs) and two trucks, retrofitted with particulate filter systems were tested along with a new identical model LHD and truck equipped with exhaust systems consisting of a catalytic converter (DOC) and muffler. The test vehicles were operated individually inside the isolated zone for approximately 4 hours over simulated production duty cycles. Measurements of ambient concentrations of particulate matter, tailpipe emissions, and engine parameters were performed for each of the tested vehicles. The DPM samples for carbon were collected at the most up- stream end of the isolated zone, at the vehicle next to the operator, and at the most downstream or exhaust end of the isolated zone. The DPM samples were analyzed for total (organic and elemental) carbon using NIOSH Analytical Method 5040. Ambient concentrations of particulate matter at the exhaust end of the zone were also measured using Scanning Mobility Particle Sizer (SMPS), and real time PAH monitor (PAS 2000). Efficiency of the filters was also evaluated on a basis of tailpipe measurements performed using raw exhaust instruments the NanoMet and the UGAS. In addition, relevant engine parameters were obtained using Detroit Diesel Diagnostic Link (DDDL) and from exhaust backpressure and temperature measurements. Results from the tests proved conclusively that diesel particulate filters can significantly reduce the concentrations of air- borne DPM, but not without careful monitoring of both ambient and tailpipe emissions and not without careful attention with respect to maintaining the integrity of the DPF systems.

By Clarence Hall, Spencer P. Howell

This bulletin deals with the characteristic features of the principal explosives used in mining and engineering operations, and espe- cially with the tests that show the suitability of different classes of explosives for different kinds of work. The Bureau of Mines pub- lishes the report as one of a series dealing with tests of explosives and methods of reducing the risks involved in the use of explosives in mining operations. The application of explosives to engineering and mining opera- tions has increased rapidly in recent years. According to a pre- liminary report issued by the Bureau of the Census, 469,000,000 pounds of explosives was manufactured in this country during the year 1909, and the greater part of this production was used for industrial purposes. In large engineering projects and in mining operations requiring the use of explosives the selection of a suitable explosive from the many varieties offered for sale is of fundamental importance. Vari- ous considerations are involved in the selection of an explosive of proper class for the blasting to be done. Many explosives suitable for quarry work are unsuitable for use in deep mines or in close workings. In metal mining and in driving tunnels the character of the gases evolved by the explosive on detonation is an important consideration. An explosive for use in gaseous or dusty coal mines must be formulated and compounded so that its flame temperature and the height and duration of its flame are reduced enough to per- mit its being used with comparative safety. In wet workings or in submarine blasting explosives impervious to moisture are requisite. In extremely cold climates explosives that do not require thawing are desirable, provided they are equally good in other respects. An essential requirement of all explosives, especially of those for use in tropical countries, is that they shall remain stable without change in chemical or physical characteristics.

Jan 1, 1913

By David White

The purpose of the studies that form the basis of this report was to learn from microscopic examinations of coal how far and in what ways the grouping of coal by types depends on differences in the kinds of plant material from which it was formed and on the condi- tions of its accumulation, or how far the special characters or qualities of coal of any type were determined by the nature and the state of the plant débris from which the coal was formed. The fact is almost universally accepted that beds of coal represent accumulations of vegetal matter in varying stages of preservation, with, as a rule, very small proportions of the remains of animal life. Mingled with the organic substances are different inorganic mineral sediments, which, together with the mineral matter originally con- tained in the plants themselves, constitute the "ash" of coal. The examination of coal shows that the kinds of ingredient plants range all the way from algee and fungi to large trees of various orders, and that these in turn vary in their own groups according to the depth and the nature of the water in which they grew and according to the other conditions of growth, such as moisture, temperature, soil, light, climate, and the competition of individuals. The species or kinds of plants and the numbers of each kind also differ greatly among themselves, not only during any one geologic period because of the changes of environment, but also from one geologic period to another, and it will be remembered that well-developed coal has been found in the strata of every period since the Silurian." Most geologists now agree that coal is transformed peat. True there is wide difference of opinion as to how the transformation has been accomplished and even as to whether coal started as such peat as is now found. Some writers insist that the higher grade coal, in its processes of development, never passed through geologic stages

Jan 1, 1913

By Charles L. Parsons

The United States produces all of the fuller's earth used for re- fining petroleum within its borders. On the other hand, most of the fuller's earth used in bleaching edible oils has been imported from England. Recently a few of the refiners of cottonseed oil have begun to utilize domestic fuller's earth, whereas others have been unable to substitute it successfully for English earth in their practice. Many samples of American earth distinctly superior in bleaching power to the English earth have come to the attention of the Bureau of Mines. For these reasons an investigation of the mining, preparation, and use of fuller's earth in this country, especially in its application to edible oils, was conducted in order to ascertain why our own raw material has been deemed inapplicable to our needs. During the calendar year 1912, according to figures of the United States Geological Survey," there were imported into the United States 1,970 tons of unground fuller's earth, valued at $11,619, and 17,139 tons of ground fuller's earth, valued at $133,718, these values being based on the wholesale market price at the port of origin. The addition of transportation charges, commissions, etc., make the price to the American refiner $14.50 to $16 per ton. Accord- ing to the latest figures compiled by the United States Geological Survey, the United States in 1912 produced 32,715 tons of fuller's earth, valued at $305,522, or $9.34 per ton, at the mine. Most of this domestic production was from three plants in Florida and one in southwestern Georgia and was used almost wholly for decolorizing petroleum. A small amount from other localities was used in the refining of edible oils. No figures definitely differentiating fuller's earth from other clays are kept in regard to our exports, but it is certain that several thousand tons of domestic earth was exported to Germany, and it is also true that German refiners of edible oils have

Jan 1, 1913

By A. S. Watts

Throughout the Appalachian Mountains there are dikes of coarse granite or pegmatite, which were intruded into other rocks. These pegmatite dikes contain feldspar, quartz, white mica (muscovite), black mica (biotite), and other minerals, such as beryl, garnet, and tourmaline. The investigation here reported has to do only with the dikes of the southern Appalachian region, in which the abundance of each mineral is as in the order given above. The pegmatites of this region are in every stage of alteration from those in which the feldspar is fresh to those in which the feldspar has decomposed to kaolin. The muscovite (white mica) shows no evidence of alteration, although most of the other associated minerals show traces of disintegration where the feldspar is completely kao- linized. At many places mining for mica has been done in dikes in which the feldspar is completely kaolinized, though the only evi- dences of disintegration in the mica are clay stains which are some- times noted between the outside lamina. Mining in these pegmatite dikes antedates history, traces of prehis- toric workings and some crude mining implements of stone having been unearthed by recent operations. The prehistoric mining is generally supposed to have been for mica, although investigations fail to show that the aborigines put the mica obtained to any par- ticular use except for ornaments, a few mica ornaments having been found in mounds in this region. The search for kaolin or semikaolinized feldspar is a plausible ex- planation of these prehistoric workings; all of them were in pegmatite that is more or less altered, and seemingly stopped only when the pegmatite became too hard to permit working with crude stone im- plements. The dumps do not represent the amount of material that one would expect, from their extent, the workings to have produced. The kaolin obtained was doubtless conveyed to the coast and sold to English traders for use in the manufacture of some of the early

Jan 1, 1913

The Mine Safety and Health Administration (MSHA) defines an independent contractor as "any person, partnership, corporation, subsidiary of a corporation, firm, association or other organization that contracts to perform services or construction at a mine." Contractors that perform specific types of work are required to report the number of employees who perform work at coal mines and at noncoal mines.

Jan 1, 2004

By Maria I. De Rosa

For all coal mining categories, data on coal mine fires during 1990-1999 have been reported as actual numbers and calculated values. 1. For each mining category, actual numbers include the total number of fires, fire injuries, employees' working hours, lost workdays, and coal production (for underground and surface mines only) for a 1 0-year period (1 990- 1999) and for five successive 2-year periods with the 10-year period. These numbers have also been reported by state ( 10-year period). The actual number of fire fatalities has been reported by time period. Furthermore, actual numbers of fires for the five 2-year periods have been reported by ignition source, method of detection and suppression, equipment involved, location, and burning material. Actual numbers of fire injuries per number of fires causing injuries and total fires have been reported by year, ignition source, equipment involved, and location. 2. For each mining category, the calculated values include the fire and injury risk rates during the 10-year period and the five 2-year periods. The fire risk rate (Frr) values were calculated according to the USBM formula [Pornroy and Carigiet 19951. The injury risk rate (Irr) values were calculated according to the MSHA formula [MSHA 1991a, 1992, 1993, 1994a, 1995a, 1996, 1997, 1998b, 1999c, 20001. Also, risk rate values for individual states (10-year period) were calculated according to the above-mentioned formulas. Of note is that only the risk rate values for the 10-year and five 2-year periods and risk rate values for individual states with the highest number of fires and fue injuries were considered for comparison purposes. The fatality risk rate values were not calculated because of the extremely small number of fire fatalities during the 1 0-year period. 3. Calculations of risk rate values are as follows: a. Fire risk rate (Frr) value: Number of fires per million tons of coal produced [Pornroy and Carigiet 19951. b. Injury risk rate (Irr) value: Number of fire injuries multiplied by 200,000 working hours per total employees' working hours [MSHA 1991a, l992,1993,1994a, 1995a, 1996, 1997, 1998b, 1999c, 20001. The Irr value is the average risk rate value for the number of fire injuries per 200,000 working hours for a given time period.

Jan 1, 2004

By Martin Harper

This paper concludes a five year program on research into the use of a portable X ray fluorescence (XRF) analyzer for analyzing lead in air sampling filters from different industrial environments, including mining, manufacturing and recycling. The results from four of these environments have already been reported. The results from two additional metal processes are presented here. At both of these sites, lead was a minor component of the total airborne metals and interferences from other elements were minimal. Nevertheless, only results from the three sites where lead was the most abundant metal were used in the overall calculation of method accuracy. The XRF analyzer was used to interrogate the filters, which were then subjected to acid digestion and analysis by inductively coupled plasma optical emission spectroscopy (ICP OES). The filter samples were collected using different filter holders or "samplers" where the size (diameter), depth and homogeneity of aerosol deposit varied from sampler to sampler. The aerosol collection efficiencies of the samplers were expected to differ, especially for larger particles. The distribution of particles once having entered the sampler was also expected to differ between samplers. Samplers were paired to allow the between sampler variability to be addressed, and, in some cases, internal sampler wall deposits were evaluated and compared to the filter catch. It was found, rather surprisingly, that analysis of the filter deposits (by ICP OES) of all the samplers gave equivalent results. It was also found that deposits on some of the sampler walls, which in some protocols are considered part of the sample, could be significant in comparison to the filter deposit. If it is concluded that wall deposits should be analyzed, then XRF analysis of the filter can only give a minimum estimate of the concentration. Techniques for the statistical analysis of field data were also developed as part of this program and have been reported elsewhere. The results, based on data from the three workplaces where lead was the major element present in the samples, are summarized here. A limit of detection and a limit of quantitation are provided. Analysis of some samples using a second analyzer with a different X ray source technology indicated reasonable agreement for some metals (but this was not evaluated for lead). Provided it is only necessary to analyze the filters, most personal samplers will provide acceptable results when used with portable XRF analysis for lead around applicable limit values.

Jan 1, 2007

By C. R. Hopkins

"The petroleum refiners of the United States made rapid strides in fuel economy in 1928, when the calculated number of B. t. u. required to refine a barrel of crude petroleum was 637,000 as compared with 698,000 in 1927, a decline of 9 per cent. The major portion of this indicated increase in fuel efficiency was undoubtedly due to the gain in use of the pipe-still and the continuous process of refining as contrasted with the old batch method of distillation.,Almost without exception the new refineries are equipped with one or more pipe-stills, and many of the older plants are changing over to this type of equipment. The refineries of the Appalachian area are among the oldest and most conservative of the country, yet a number of them dismantled their old shell and cheese-box stills and installed pipe-stills in 1928.The more extensive use of the pipe-still was not the only way in which the refiners lowered their fuel requirements in 1928. The use of heat-exchangers, in which the heat from hot vapors to be condensed is used to heat the incoming cold oil, also increased in 1928, and in addition the refiners have kept abreast of the times in saving fuel through better insulation and improved burners.For the year 1928 the refiners burned as fuel the following: 46,400,000 barrels of-fuel oil; 3.362,000 short tons of coal; 114,950,000,000 cubic feet of natural gas; 77,313, 000,000 cubic feet of refinery or still gases; and 470,000 short tons of coke, in addition to a little electricity. This fuel was calculated to have produced a grand total of 582,156 billions of B. t. u., as compared with 578,784 billions B. t. u. in 1927.The total of 46,400,000 barrels of fuel oil burned represents an increase over 1927 of about 5,000,000 barrels, which made it about equal to the 1926 figure. Practically all of the refinery districts used more oil as fuel in 1928. The most important increase - over 2,000,000 barrels - occurred in the East Coast district, where greatly expanded throughput of foreign crude was instrumental in increasing fuel-oil production.The use of coal for fuel at refineries again registered a material decline, the total for 1928 of 3,362,000 short tons being 33 per cent below that of the previous year. The outstanding decrease in the use of coal in 1928 occurred in the East Coast district, where coal was probably replaced by oil. The use of coal for fuel at refineries in the States of Ohio, Pennsylvania, and West Virginia declined materially in 1928; the substitute used in the majority of cases was oil burned in pipe-stills."

Nov 1, 1929

By Stephen L. Tillim

Tubular Handles can negatively affect the contents of the carpal tunnel. Years of injuries from grasping handles for tools and machines can cause carpal tunnel syndrome, tendonitis and wrist joint injuries. The can cause inability to use a hand and resulted in the longer absences from work than injuries from falls, accidents or fires.1 Cylindrical, tubular and rectangular handles are rolled flat structures. They place the hand on a rolled flat surface where the ends of the middle and ring fingers overlap the index and small fingers. They are pulled along a series of lines that contact the end joint of the index finger, the middle bones of the middle and ring fingers and the end bone of the small finger. Cylinders are pulled diagonally in the hand toward the carpal tunnel (CT) area. Gripping in this manner tenses asymmetric muscle groups in the forearm. Handles could work better if they do not place pressure on the CT and conform to the natural function or neutral hand position where the hand rests or dangles at the side of the body, the finger tips form a diagonal, the palm and fingers form a cup, the thumb rests between the index and middle fingers and the wrist is mildly extended. However, handles designed for the neutral position are pulled by diagonally oriented fingers into the valley between the thenar and hypothenar muscles where they can compress the median nerve and tendons exiting the CT. Seven principles for handles that do not place pressure on the carpal tunnel and employ optimal hand position are presented. First, handles should align the ends of the fingers parallel to the horizontal crease and not diagonally. Second, handles should extend from the cupped fingers to meet the muscles at the base of the thumb on the radial side of the hand and extend further on the other or ulnar side to meet a portion of the small muscles. Third, handles should have a recess on the proximal side to prevent contacting or placing pressure on the carpal tunnel. Fourth, handle design should be based on hand measurements in a position of function. Fifth, handles should come in sizes. Sixth, handles should be placed on tools to maintain the wrist and elbow in neutral position. The seventh is handles should support the maximum area of the hand and absorb, but not direct, vibration to the carpal tunnel. These principles led to prototypes and patents for handles for gripping, pinching and squeezing2,3,4 . The poster will illustrate and explain the principles Bonsil handles. Research, with existing tools, is needed to substantiate claims made for the Bonsil handle.

Jan 6, 2006

By John W. Frey

This paper presents one of a series of digests of foreign mining legisla- tion and court decisions which is being prepared in advance of a general report relative to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Trinidad has been prepared from the best information available in ashington but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State.

Sep 1, 1930

By Gary P. Sames

This report discusses some practical applications of a geotechnical investigation conducted by the U.S. Bureau of Mines that can help mine operators meet revised Federal regulations in their roof control plans. The investigation, designed to characterize roof conditions near the coalbed outcrop in drift coal mines in eastern Kentucky, revealed that weathered stress-relief joints near outcrop are crucial ground control factors in the region. The joints' origin and character were determined through underground mapping of many joints in coal mine roof and detailed observations and measurement of joint trends and physical characteristics in widely separated strip mine highwalls and roadcuts. This resulted in an understanding of stress-relief-joint patterns and the effect of various rock types on the intensity of weathering in the joints. That information is used in this report to show how stress-relief joints contribute to roof failure and how, through improved roof support and mine planning, safer roof support plans can be developed.

Jan 1, 1992

By Charles L. Parsons

During the past year, in producing 500,000,000 tons of coal we wasted or left underground, in such condition that it probably will not be recovered in the future, 250,000,000 tons of coal; we turned loose into the atmosphere a quantity of natural gas larger than the total output of artificial gas during the same period in all the towns and cities of the United States; we also wasted or lost in the mining, preparation, and treatment of other important metalliferous and non- metalliferous minerals from 10 to 50 per cent of the year's produc- tion of such minerals. These losses serve to indicate the importance of inquiries and investigations by the Federal Government for the purpose of lessening the waste of essential resources-investigations on the same general lines as those looking to a reduction in the loss of life in the mining operations of the country and the far more exten- sive investigations looking to the more efficient production and use of agricultural products, both of which are being conducted by the Federal Government. In a consideration of the possible activities of the individual, the State, and the Federal Government in behalf of a less wasteful use of our mineral resources certain facts and principles should be kept clearly in mind, namely: That the present generation has the power, and it will exercise the right, to use as much of the country's resources as it actually needs; there can and there will be no such thing as stinting the present gen- eration by bottling up resources for the use of the future. That the Nation's needs are not likely to be curtailed; these needs will increase with the extent and diversity of the Nation's industries, and they will increase more rapidly than population increases, for the reason that the per capita consumption of mineral products is rapidly increasing; and That the men of this generation will not mine, extract, or use these resources at continuous financial loss to themselves in order that some- thing may be left for the use of future generations; there can be no such thing as a mineral industry without profits.

Jan 1, 1912

By John N. Murphy

INTRODUCTION It's a pleasure to be with you and to share in this opening session for the 27th Annual Institute on Mining Health, Safety, and Research. As we come together today, I would like to reflect for just a moment on the past Institutes. Much of the progress in Mine Health and Safety has been the subject of presentations and discussions at the previous Institutes, either by identifying the issues, proposing techniques to overcome the problems, or presenting new findings to address important issues for the mining industry. May I extend our thanks and congratulations to VPI and to the planners and organizers of all of these Institutes for their important contributions to our mutual goals of improving mine health and safety. In the time available today, I would like to accomplish two objectives: 1. Provide my assessment of the current status of the Mining Health and Safety Research Program; and 2. Share with you the continuing need and direction for the Mining Health and Safety Research. MINE HEALTH AND SAFETY RESEARCH TODAY Mine Health and Safety Research was conducted formerly at four geographical locations within the USBM, specifically: Pittsburgh, Spokane, Twin Cities, and Denver. Although the Twin Cities and Denver Centers were closed, we have been successful in relocatingfmaintaining much of the core competencies to conduct a responsive, multidisciplinary Mine Health and Safety Research Program. The current staff at Pittsburgh and Spokane directed toward Health and Safety Research totals 397. This includes Lake Lynn Laboratory, about 60 miles southeast of Pittsburgh, where large-scale mine fire and explosion research is conducted. With the closures and transition we have worked to maintain the core competencies necessary to address Health and Safety issues. In some cases we have made arrangements to provide the requisite core competencies through external organizations. An example is the reassignment of the diesel particulate instrumentation capability from Twin Cities to Pittsburgh. In the case of diesel emission control, due to the cost of relocating laboratories and the lack of the appropriate skills at Pittsburgh or Spokane, the emission control laboratory is now being operated in Minneapolis through a contractual arrangement with the University of Minnesota.

By Oliver Bowles

"The introduction into mines, quarries and manufacturing plants of machines and tools operated by compressed air has revolutionized methods of operation to an extent comparable only with that occasioned by the invention of explosives and the utilization of electricity. The use of compressed air in pneumatic tools, in rock drills, and for the operation of pumps and other machinery is well known to most miners and quarrymen, but its application as a substitute for explosives for breaking rock in a few granite quarries has received little publicity.In the region of Lithonia, a few miles from Atlanta, Georgia, is a dome of massive granite used widely for building stone and for paving blocks. The most remarkable structural feature of the granite is the absence of joints and sheeting planes. The term ""joints"" is applied to open fractures that commonly occur in rocks, usually vertical in direction or nearly so, and spaced from a few inches to several feet apart. On the Lithonia granite outcrop, however, one may walk over the bare rock surface for hundreds of feet without finding any indications of a joint, ""Sheeting planes"" are open fractures at various levels, approximately parallel with the rock surface. The presence of such planes when spaced several feet apart greatly facilitates quarrying, and where absent, as at Lithonia, the necessary fractures must be made artificially.The forcing of artificial sheeting planes is accomplished as follows: Two holes of about 3-inch diameter arc drilled close together and to a depth of about 8 feet. Two men work at these holes all summer, and sometimes part of a second summer. A very small charge of black blasting powder, not more than a spoonful, is placed in each hole, tamped with clay, and the charges are fired simultaneously with an electric battery. This starts a small fracture running outward from the bottoms of the holes. There is in most granites one direction of easy splitting known among quarrymen as the ""rift"", and as the rift direction in the Lithonia granite is horizontal the fracture follows a horizontal plane,"

Aug 1, 1920

By E. P. Youngman

The mining law of the Belgian Congo does not cover the Province of Katanga nor the District of Kivu (in Eastern Province). Regulations of the Comité Spécial du K tanga are in force in Katanga and those of the Comité National du Kivu in Kivu. The three laws differ only in detail, and grants made by the Comité Spécial du Katanga or by the Comité National du Kivu must be approved by the Ministry of Colonies. The following résumé is designed to coordinate the three sets of regulations.

May 1, 1930

By Lisa Steiner

Almost every process has a predecessor, and studying the predecessor helps to define needs and shortcomings to be addressed in the new design. It also suggests what information is needed by the users in order for them to be able to operate safely and effectively. The end users of a system can provide important feedback to better evaluate the current and proposed designs. When new technology is introduced into a system, mishaps may occur before it is realized that human-system interactions were not considered adequately in the design process. A systematic methodology to evaluate the causes of these injuries and to develop remedial recommendations can enhance safety. This paper illustrates how such an approach was used to assess remote machine operation in underground coal mines. The dynamic work environment of underground mining with its unpredictable geologic anomalies can result in numerous hazards. Many of these hazards, including mine roof collapse, occur near the working face where coal is being extracted. The face area is also where the most intricate interactions of people and equipment occur. For these reasons, a high priority has been placed upon minimizing hazards to the workers at the face. A remote control operation was introduced to provide a safer working distance from these hazards. As the remote control technology began to be widely used for extended cut mining operations, new issues became evident. It was essential to develop mechanisms for mines to evaluate these issues in order to predict and reduce injuries. Mining methods and equipment changes must allow for the ability of workers to adapt to changes in their dynamic mining environment. Consideration should be given to how the worker will use familiar information to make decisions in now unfamiliar situations. There will be both intended and unintended consequences [Merton, 1949]. Designers try to anticipate and eliminate surprises, but it is impossible to eliminate them all. How, then, will the new system affect the tasks to workers which are currently accustomed? As suggested below, this question may be addressed and more of the unintended outcomes predicted with a planned design process which includes strong human factors input to determine interactions and behaviors of participants.

Jan 1, 2005

By D. B. Taliaferro, David M. Logan

which an operator may obtain detailed information regarding all projects in the State. It is the purpose of this report to present data such as volume of oil produced monthly, volume of water injected monthly, spacing of wells, number of injection wells and oil wells, and other such pertinent information regarding every project in the State whether active or abandoned and whether a success or a failure. It is believed that with these data it is possible to analyze water-flooding operations in this area more completely than has been possible in the past. As the title indicates, the report is essentially a history, and ordinarily no opinion is given as to the cause for the success or failure of individual projects. Increasing the production of oil is exceedingly important at this time, and one method by which it may be done most readily is by providing additional energy for the movement of oil in many of the older fields. In many oil fields the predominant force that drives oil through the porus reservoir rocks to wells is the gas dissolved in or otherwise associated with the oil under pressure. As the pressure in the reservoir declines in consequence of the removal of fluid, gas comes out of solution in the form of minute bubbles; as the pressure is reduced further, the expansion of these bubbles forces part of the oil toward the areas of lowest pressure and into the producing wells. The physical properties of the oil and the gas governing their flow through reservoir rocks to wells differ, and much of the gas slips past the oil leaving large quantities of oil in the reservoir when the pressure has been exhausted. Often the natural productive life of fields is prolonged by reducing the pressure in oil wells below atmospheric with vacuum pumps; but the ad- ditional energy made available in this manner is limited to less than 1 atmos- phere of pressure, and even after the extended application of "vacuum" to a petroleum reservoir large quantities of oil are left unrecovered in the porous rocks and sands.

Nov 1, 1943

By Henry Kreisinger, F. K. Ovrız

Some of the investigations conducted by the Bureau of Mines have for their object the collecting and disseminating of information regard- ing methods by which the fuels of the country may be most effi- ciently used. As the analysis of flue gases tends to develop better methods of firing, which in turn reduces waste of fuel, the Bureau of Mines in this bulletin presents for the benefit of those in charge of boiler plants and all other persons interested detailed information on methods of sampling and analyzing flue gases, and on the utilization of the analyses in promoting boiler-room economy. This bulletin is intended to be a companion to Technical Paper 80," and is written in plain and nontechnical language, as far as pos- sible, so that it may be readily understood by persons who have not had the advantage of a technical education. Whenever possible, illustrations of apparatus and methods of handling have been used rather than elaborate descriptions. The material presented in this report is arranged in two parts. The first part contains the description of the apparatus and the methods used in sampling and analyzing flue gases. The second part gives experimental results obtained with the different methods of sampling and collecting flue gas that are recommended in the first part of the report. Only simple apparatus and methods are considered, as they are accurate enough to show the large heat losses due to the use of too much air, and are also accurate enough to indicate any incomplete combustion losses of economic importance. Without doubt the loss due to large excess of air is the greatest one in the boiler room, and can usually be greatly reduced by making proper use of gas analysis. Before engineers in the isolated industrial plants can be induced to analyze for small traces of combustible gases, they must be first taught how to analyze for carbon dioxide (CO), and they must learn to appre- ciate the great possibilities of reducing loss from large excess of air. Furthermore, in the face of the great difficulty of obtaining a fair

Jan 1, 1915