Search Documents

New Continuous Personal Dust Monitors (CPDM) submitted to NIOSH for approval to sample coal mine dust must accurately measure respirable coal mine dust in mine environments. There are two steps in the process which may be done in any order. The manufacturer is required to submit the results of a comparative underground coal mine dust sampling study, where the candidate CPDM is compared to an approved coal mine dust sampling device (currently the Coal Mine Dust Personal Sampling Unit (CMDPSU)). This testing shall follow the guidelines outlined below and shall demonstrate through weighted regression analysis that the mean coefficient of variation with bias correction is equal to or less than 12.8%. The other step involves laboratory testing to determine the electronic and environmental stability. This testing must be conducted by a private, commercial, academic or other laboratory approved by NIOSH.

Jan 1, 2009

By Doris M. Hyde

Mineral industry activity in many of the smaller Caribbean Island countries has remained minimal. For this reason, specific references to Bermuda, Guadeloupe, Martinique, and the Netherlands Antilles have been removed from textual and trade table presentations. Any significant future developments will be reported as they occur. Readers are referred to earlier Minerals Yearbook editions for previous information. Table 1 production statistics have been modified in some instances. References to certain nonmetal commodities were eliminated because information has often been unreliable. Their inclusion in table 1 was not considered important to either an overview of the area or to compatibility with volume I of the Minerals Yearbook.

Jan 1, 1984

By A. B. Hooker, L. C. IlsLey

Several ignitions or mine pa, which might have led to explosions, and at least ona mine fire attributed to heated leg wires of electric detonators, have occm.rred. at rn1::.es in which outside shot firing is practiced. Photographs taken at one mine ind.la.ted. that the wires became red hot during firing. These results having been --i·-led. to the .Lttention of the electrical section of the Bureau of the Mines, ignitions the tests and to reportd aid in herein preventing were made future to trouble determine of if this possible kind, the cause of The investigation, which 1• considered preliminary, included tests to determine the conditions tha.t cause gas ignitions from heated. leg wires of electric and. of detonators, copper leg possible wires, remedies The tor samples such of heating, wire used. and in the the relative test were behavior the of reg\llar ironDa. Pont iron and copper leg wires (No, 22 A,W,G.) C\1t from Du. Pont electric detonators.

Aug 1, 1922

By C. M. McKinney

Bureau of Mines routine crude-oil analyses of 42 samples from 37 fields in the major producing areas in Mexico are presented in this report. Table 1 includes information on the source and general characteristics of each sample. Table 2 gives a summary of analytical and computed data. A map (fig. 1) shows approximately where the samples were obtained. ACKNOWLEDGMENTS Grateful acknowledgment is made to Alfonso Barnetche, manager of production, and Ing. Francisco Inguanzo, assistant manager of production, both of Petroleos Mexicanos, who supplied the crude-oil samples and furnished information concerning their sources.

Jan 1, 1960

By Richard H. Spencer

Since the passage of the Coal Mine Health and Safety Act of 1969, the Bureau of Mines has made many advances in mine communications. These efforts have resulted in the following developments and demonstrations: Surface-to-surface electromagnetic transmission of baseband voice signals through overburdens as deep as 600 feet. This transmission was achieved with equipment from the Interim Mine Rescue and Survival System Program, and demonstrated that baseband voice communications could be obtained through these overburdens in the absence of mine-generated noise; that is, when the mine power system was shut off, However, during mine operational conditions, the mine-generated noise proved to be so large that effective baseband voice communications to the desired depths could not be effected.

Jan 1, 1975

By J. L. Shultz

The investigation of organic compounds in respiratory coal dust by high-resolution mass spectrometry has shown that the organic components differ (1) with particle size, (2) with rank of coal, (3) in coals of same rank from different coal seams, and (4) in respirable mine dust and respirable coal dust (prepared) from the same mine. The eight respirable mine dusts studied are from coal seams in the Appalachian region where the incidence of coal workers' pnumoconiosis is relatively high. The molecular weights of the major organic components vary greatly among these respirable mine dusts; three show strong concentrations of polynuclear aromatic hydrocarbons.

Jan 1, 1972

By C. W. JEFFERS

During the past few years the use of mechanical equipment for the loading and transportation of coal at the working face has rapidly increased . Many mining officials are of the opinion that mechanical methods have tended to reduce the hazards of mining, and a number of statements have been made to this effect . Little actual data upon which to base conclusions in regard to the relative safety of various methods of mining have been made available . While it may be possible that these systems of mechanical mining are inherently less hazardous , obvious dangers should not be disregarded in the belief that the mere act of installing mechanical loading equipment automatically brings about better accident records . The same rules and regulations , modified to meet the new regime must be applied with the same discipline as heretofore . By diligent study and application there is reason to believe that new methods of concentrated mining can be utilized with at least a possibility of increased accident performance . With the idea of preventing accidents by taking available precautions against their occurrence , attention should be directed to the dangers that exist where room and face conveyors are in operation . Due to the cost pressure prevalent in the mining industry at the present time mechanical means are often used in an attempt to decrease cost of production. The management , after having spent considerable sums of money for new equipment , is expected by stockholders and investors to show results by increasing tonnage and reducing operating costs . Consequently the operating officials apply the same pressure to local mine officials to obtain results . The natural reaction of the superintendent and mine foreman is to secure the maximum production from the new method , and unfortunately safety is frequently , if not generally , sacrificed to this end . In many instances , operators of new types of mechanical loaders are difficult to secure and after being obtained are difficult to hold , especially if the new equipment is more or less in the experimental stage . The tendency is to handle the machine operators with " gloved hands " and to permit many unsafe practices which ordinarily would not be allowed, in order to keep from antagonizing them and losing their services . Although these unsafe practices become habitual and even uneconomical , conditions thus established are difficult , sometimes impossible , to change .

Jul 1, 1930

By L. C. IlsLey

"Nearly every piece of electrical equipment used in mines ""breathes."" In other words, motors, controllers, rheostats, switches, and other similar equipment, even though encased in seemingly tight compartments, breathe in the atmosphere that surrounds them.As the apparatus is used, the temperature of metallic parts is changed generally in positive direction through the heat by friction and the heat due to the electric current. When the apparatus is idle it gradually cools down to the temperature of the surrounding atmosphere.This increase of temperature during operation and return to normal temperature when operation stops alternately raises and lowers the temperature of the atmosphere within the compartments which, in strict accordance with Charles' law -will expand or contract in proportion to any given temperature change.As compartments are not gas-tight, such expansion and contraction will force the atmosphere out of the compartment =on expansion and suck the surround¬ing atmosphere into the compartment during contraction, hence the term ""breathing.""Investigators2 of explosion-proof equipment have recognized that such an interchange would take place and have designed their equipment to safeguard possible explosions within the compartments."

Jun 1, 1927

By H. G. Iverson

As a part of the program of investigation of domestic sources of manganese ore, mining engineers of the Bureau of Mines examined and sampled three properties in the vicinity of Winnemucca, Nev. As the ores were too low grade for direct production of ferromanganese, they were tested for their amenability to concentration by ore-dressing methods. Two samples of ore were procured by examining engineers of the Bureau of Mines from several outcrops in the Pollard Canyon area, Pershing County, about 30 miles southeast of Winnemucca. The manganese occurs in relatively small lenticular bodies as secondary replacement deposits in chert and quartzite. The first sample represented average run -of -mine ore as exposed in the Pollard Canyon deposits. Sample 2 was composed of hand-sorted, high-grade ore.

Jan 1, 1954

By Sumner M. Anderson

ATHOUGH scattered signs of increased activity in the mining industry accompanied an incipient improvement in the overall economic situation during the latter months of 1963, production levels for the year as a whole responded to the general 1962-63 business recession with a 4.2 percent decline. The petroleum industry, active since 1907, did not become a dynamic force in the economy until exploration and drilling contracts were concluded with private companies in 1958 and 1959; on November 15, 1963, having virtually achieved self-sufficiency in petroleum in the preceding year, those contracts were unilaterally annulled. In the field of metallics, the only approach to internal sufficiency-aside from the iron and steel industry that has depended heavily on the importing of basic raw materials-has been in mining, smelting, and refining lead and zinc although iron ore, silver, beryllium, tantalite, and tungsten have been mine production items of economic significance. Reserves of lead, zinc, silver, bismuth, vanadium, and low-grade and metallurgically difficult iron ore-as well as those of beryllium, tantalite, and tungsten which are produced primarily for export-appear to be fairly abundant. The exploration of deposits of copper, cobalt, tin, lithium, gold, manganese and uranium has been undertaken on a relatively small scale, and little precise information is available on the extent of reserves. Argentina is dependent on foreign sources for part of its required iron and steel and, except for lead and zinc, most of its nonferrous metals. Nonmetallies and solid fuels present an exceptionally varied array of production items among which cement had the second largest 1963 output in South America. Borates, bentonite, common clay, diatomite, fluorite, granite, lime, limestone, obsidian, onyx, rhodochrosite, salt, and spodumene ordinarily are produced for export either exclusively or in excess of domestic consumption requirements. Barite, cement, chalk, gypsum, marble, and mica are both exported and imported. Argentina depends entirely or partly on imports for coal and coke, certain special types of clay, mineral abrasives, graphite, magnesite, mineral fertilizers, sulfur, talc, and minerals for construction, the last group being chiefly attributable to convenience of river transport from Uruguay.

Jan 1, 1964

By Jalna R. Zatko

Coal-clay waste slurries were dewatered in laboratory-and small-scale continuous tests by the Bureau of Mines using polyethylene oxide (PEO) as a flocculant. Dewatering from a nominal 7-wt-pct solids to over 50-wt-pct solids was accomplished using 0.5 lb of PEO per ton of feed in small-scale continuous tests. Parameters such as pH, initial solids content, and PEO concentrations were investigated. Water recovered from dewatering was reused as dilutant for PEO solutions.

Jan 1, 1982

By T. A. Evans

The Bureau of Mines conducted a Laboratory and pilot-plant investigation of the flotation of iron sulfides from zinc-lead mill tailings near Platteville, in south-western Wisconsin, at the North Central Experiment Station, Minneapolis, Minn. The procedures used and the results obtained in this investigation are described in this report. Samples for laboratory tests were obtained from each mill in the district, namely, Calumet & Hecla, Inc., Eagle-Picher Co., Vinegar Hill Zinc Co., and Tri-State Zinc, Inc. The sample fat pilot-plant work was obtained from the Davis Mining Enterprises mill.

Jan 1, 1957

By B. W. Gandrud

In 1927 Coghill5 showed that there is considerable liberation of the iron oxide mineral from gangue when the Alabama red iron ores are ground to a size suitable for classification and tabling, but that there is not sufficient to make possible a high extraction and a high grade of concentrate. Coghill states: High extraction and high grade of concentrate cannot be obtained without grinding to a size comparable with flotation or cyanide practice. If grade of concentrate be sacrificed the grinding need not be so severe.

Jan 1, 1934

By P. L. Placek

Correlations were made on experimental data for four New Mexico ore series to determine relationships between ore grade and uranium extraction during leaching operations. Such relationships provide information needed to predict the long-range supply of minerals to meet national economic and strategic needs. Results show that other ore constituents and gangue materials in addition to uranium grade influence uranium extraction. In general, tailing grades decrease and uranium extraction increases as both H2S04 and NaCl03 concentrations increase. Terminal emf and terminal pH also were studied. Similar trends appeared for all ores; however, specific combinations of results also were observed for individual ores and ore series. Experimental results indicate that uranium extractions are higher for lower uranium feed grades than predicted by other estimates. Three factors--uranium feed grade, H2SO4 concentration, and NaC103 concentration--were used to design factorial experiments for each ore series. Four additional feed assay factors--V205, Fe, C02, and CaO--were included in regression equations to account for some of the variation in data. The three factorial factors are represented in the regression equations by linear and exponential terms of the form D i'1*G i + Di,2 *e Di, 3*Gi. The four additional assay factors are represented by linear and squared terms of the form Di,*Gi + Di,2*eDi3*Gi. where the Di, ,J are coefficients, the Gi are factors, and the symbol * represents multiplication in computer notation. The interactions of the factors are represented by products of the nonlinear terms for all pairs of the factors.

Jan 1, 1981

By Robert H. Peters

This U.S. Bureau of Mines report identifies the types of serious accidents that occur most frequently at small underground coal mines and describes the strategies that could help prevent these accidents. A wide variety of methods for improving safety are suggested, including improvements in the design of equipment, work procedures, work schedules, safety programs, and emergency response plans, as well as techniques for diagnosing the potential hazards associated with new technologies and work procedures. Some of the papers in this volume focus on preventing specific types of mining accidents--ones associated with materials handling (primarily back injuries), equipment maintenance, improper machine guarding, and ground failure during retreat mining. Although the recommendations in this volume are heavily influenced by research performed at underground coal mines in the Appalachian coalfields, most of the papers contain advice that is equally pertinent to almost any type of mine.

Jan 1, 1994

By Barbara Fotta, Lynn Rethi

Within the Mine Safety and Health Administration's (MSHA's) classification of metallnonmetal (MAM) mining, the number of independent contractor' employees has increased significantly in recent years. In 1985 independent contractor employee hours reported to MSHA accounted for 4.5% of all M/NM mining employee hours (excluding office workers); by 1994 that proportion had doubled to 9.0%. As a result, these workers now account for an increasingly significant proportion of fatal and nonfatal mining accidents. According to MSHA's statistics, annually computed fatality incidence rates (the number of fatalities per 200,000 employee hours) for independent contractors working in M/NM mining are consistently higher than those for operator employees. Over the five-year period from 1990 through 1994, 53 independent contractor employees were fatally injured while working on M/NM mine property (See Table 1). More than one third of these fatalities (36%) were due to accidents involving powered haulage; 21% were machinery accidents; and 11% percent were falling material accidents. Combined, these three accident classifications accounted for 68% of all independent contractor fatalities occurring on M/NM mine property during these years. Clearly, current efforts to increase the safety of the mining workforce must also address the safety of the independent contractor employee. This report is a preliminary attempt to identify trends in the employment and safety of independent contractor workers by identifying which segments of M/NM mining are experiencing the greatest increases in the number of independent contractor employees and by examining changes in the rates and types of accidents in which these employees are involved. The employment and accident data used in this report were obtained from the MSHA database. [ ]

By Sidney Katell

This report is an economic evaluation of the production of hydrogen in a continuous system by the steam oxidation of partially reduced iron oxide in a fluidized bed at 7 atmospheres using producer gas to reduce the iron oxide. The oxidation-reduction step is based on experimental data obtained by the Bureau of Mines at the Pittsburgh Coal Research Center. The estimated capital requirement for a plant producing 30 million std. c.f.d.3 of 99.8 percent purity hydrogen at a discharge pressure of 450 p.s.i.g. is $13,100,000, using January 1961 equipment cost data. Based on a 330-day operating year, the operating cost before profit and taxes with coal price as a variable is estimated to be:

Jan 1, 1962

By C. M. Frost

Crude shale oil produced by gas combustion retorting of Green River oil shale was hydrocracked over a cobalt molybdate catalyst at operating pressures of 500, 1,000, 1,500, and 3,000 psig, an operating temperature of 8900 F, and a liquid hourly space velocity of 1.0. Hydrogen feed rate was maintained at 6,000 scf/bbl. The volume-percent yields of total liquid product were directly proportional to the operating pressure. Weight-percent conversion and volume-percent yields of gasoline were directly proportional to the log of the operating pressure. Catalyst deposit percentages were inversely proportional to the log of the operating pressure. Nitrogen and sulfur removal rates as well as saturation of the liquid products increased as the operating pressure was increased.

Jan 1, 1973

By J. D. Davis

From the chemist's point of view it would be ideal if specifications for coke for any stated purpose could be written on the basis of chemical composition and burning characteristics. Unfortunately this is not possible. In fact, the physical properties of a coke are often of such major importance as to render any specified chemical requirements totally inadequate to show the quality of coke desired. For example, a furnace coke may admirably fill all chemical requirements, such as for low phosphorus, sulphur, moisture, and high fixed carbon, and still be too soft to support the burden of the furnace without excessive crushing. Again, a domestic coke though a good fuel as judged from Chemical analysis, may be of unmarketable size. Thus one can not define the quality of a coke for a specified purpose without taking into account both its chemical and physical characteristics even when this has been done the specification may fail because neither coke user nor producer can accurately define by quantitative tests the qualities most desired. In other words, there is need of accurate test methods for measuring the properties of coke and, what is equally important, for correlating the results with the behavior of the coke in use. Coke quality is determined by the kind of coal used, the coking process, and the type of equipment used in the coking process. Chemical analysis of the coals, together with small-scale coking tests, will give a good indication of their suitability; but, in general, coke must be produced on an industrial scale and tested in the equipment for which it is intended before conclusive information as to its quality is obtained.

Jan 1, 1928

By W. H. Young

THE BITUMINOUS coal and lignite industry increased substantially in 1962, compared with the 1961 figures. The major items of production, consumption, exports, and productivity increased. However, certain key items declined. The steady upward trend in mechanization failed to materialize for the third year; the percentage of total tonnage mechanically loaded remained the same as in the 2 previous years; and the tonnage mechanically cleaned was smaller than in the previous year. The percentage of total production mined by stripping and by augers increased slightly. Most significant was the continued decline in average value and employment. Production.-The output of bituminous coal and lignite in the United States in 1962-422 million tons-was 5 percent greater than the 403 million tons produced in 1961. Production was greater in 1962, owing largely to expanded consumption by the electric utilities and to more exports.

Jan 1, 1963