Search Documents

By Bruce Cantrell, K. L. Rubow

"INTRODOCTIONMeasurement of the contribution of diesel exhaust to respirable aerosol in mine environments has become increasingly important because of current concerns over the occupational health effects resulting from exposure to diesel emissions. In response to this, the U.S. Bureau of Mines is developing and evaluating new sampling methods for measuring diesel aerosol in underground mines. Two such techniques are being studied by the Bureau, size selective sampling and Chemical Mass Balance (CMB) modeling. These techniques use measurable physical or chemical characteristics of a mine aerosol sample to infer the amount of diesel particulate material contained in the sample.Size selective sampling is being adapted for measurement of diesel aerosol by the Particle Technology Laboratory (PTL) of the University of Minnesota under sponsorship by the Bureau. 1 It is based on the premise that diesel and mineral dust aerosol can be physically separated by size and collected during sampling using inertial impaction. An independent effort by the National Institute for Occupational Safety and Health to develop a size selective sampling technique was also sponsored by the Bureau.The second technique, CMB modeling, is being developed by the Bureau as an alternative measurement technique to referee the results obtained using size selective sampling.3 It compares measured trace element ""finger prints"" of aerosol sources with similar profiles of mine aerosol samples. From these, the portions of the sample contributed by each source can be determined. Results of these investigations in underground coal mines have confirmed that diesel and coal dust aerosol are of different size and can be measured separately using size selective sampling techniques.A major difference in diesel usage among underground mines is the requirement for exhaust gas cooling systems in coal and gassy noncoal mines. Nongassy mines usually employ limited exhaust conditioning in the form of catalytic converters, which have limited effect on primary exhaust particulate. The cooling system in most general use in gassy mines is the water scrubber. This device has little effect on most of the gases but removes particulate material from the exhaust. 5 Because of this, exhaust aerosol characteristics in nongassy mines are expected to be different. To see if size selective sampling techniques can be used in such mines, the Bureau and the University of Minnesota conducted a second study in three metal and nonmetal mines, two nongassy and one rated as gassy."

Jan 1, 1990

By Richard Havens

A flotation procedure was devised by the Federal Bureau of Mines for beneficiating Mount Wheeler, Nev., beryllium ores that contain the beryllium minerals bertrandite and phenacite in a complex association with calcite, fluorspar, mica, quartz, and other accessory minerals, The method also has proven to be effective in trials on ore from the Lake George, Colo., area. Samples used in most of the research ranged from 0.49 to 0.73 percent BeO. Beryllium mineralization varied from two-thirds bertrandite to all phenacite. An unusually high grade sample containing 5 percent BeO as phenacite was floated on a batch basis to prepare concentrate for utilization studies. The beryllium minerals were floated from undeslimed pulps at natural pH using sodium fluoride and sodium hexametaphosphate (HMP), as modifiers, and a fatty acid-fuel oil combination as the collector. Key factors were the use of a minimum of about 4 pounds of sodium fluoride and between 2 and 4 pounds of HMP per ton of ore. Efficacy of the HMP was related to the grind, mineralogical composition, corollary reagents, and type and time of conditioning. Addition of the fluoride, HMP, and collector in that order, followed by appropriate conditioning after each addition, was essential for satisfactory flotation.

Jan 1, 1961

By L. C. IlsLey

A specially recommended cable is a rubber-sheathed cable that has met the minimum performance requirements for cables as set forth in Schedule 20. The first in the series of recommended cables was listed September, 1930, by an ad- vance notice published as Information Circular 6375 which described the conditions under which the cable tests were made. Since that time six additional cables have met the test re- quirements and have been specially recommended. The complete list of specially recommended. cables is as follows: Specially recommended-cables Cable Symbol No. Hazacord No. 2 BM1 Stranding 19 x 7 Hazacord No. 3 BM2 do. Hazacord No. 4 BM3 do. Super-service No. 3 BM4 7 x 19 Super-service No. 2 Super-service No.. 4 BM5 do. BM6 do. Super-service No. 4 BM7 7x 7 Manufacturer Hazard Insulated Wire Works (division of the Okonite Co.) Do. Do. Rome Wire Company (division of the General Cable Corporation) Do. Do. Do. The cables listed were all twin (parallel duplex) cables having outer belts or cov- erings of approximately -inch high-grade rubber compound, and have the same general appear- ance and relative dimensions as the types of twin cables in general use. The cables were tested under conditions designed to show their approximate perform- ance under mine conditions. Only twin-type cables have met these test conditions. Although the recommended trailing cables are much better and safer for mine use than other cables and withstand being run over by a 7-ton car, they should not be considered as 100 per cent safe. The 7-ton car test represents the minimum limit requirement effective at present under Schedule 2-C, but the test car operates on a straight and level track, and thus does not represent the more severe conditions of mine use such as might result from uneven and curved tracks.

Mar 1, 1931

By L. H. Adami

This paper reports the results of solution calorimetry conducted to obtain the heats of formation of crystalline FeS04?6.952H20 and FeS04?1.008H20, from. which values were derived for the stoichiometric compounds FeS04?H20 and FeS04?H20. Also included are derived values of the free energies of formation and dehydration. This work was undertaken primarily to fill a need for data for pure, easily obtainable ferrous compounds that are suitable for use as calorimetric intermediates, The ferrous sulfate hydrates meet the essential requirements for this use.

Jan 1, 1963

By Roger J. Morrell

The Bureau of Mines conducted drag cutting experiments in hard, abrasive rock in an effort to extend the capabilities of an experimental kerf-core mining machine. The basic kerf-core mining machine cannot be used in hard, abrasive rocks because of the high wear experienced by the kerf cutters. These experiments were conducted in an effort to develop a method of preweakening the rock ahead of the kerf cutters in order to reduce the high cutting loads and hence the higher wear rates experienced by the cutters. The two "preweakening" techniques studied were indenting with mechanical wedges and single and double slotting with diamond saws. The best cutter force reduction achieved with mechanical indenting as 70 pct, whereas double slotting achieved force reductions of up to 99 pct. Conceptual designs of preweakening systems that could be retrofitted onto the basic kerfing cutterhead were developed for both the indenting and the slotting techniques. A high-energy impactor with wedge bit was used for the indenting method, and high-pressure water jets were used for the slotting method. A preliminary technical and economic analysis was performed for both of these full-scale systems to illustrate the methodology and to point out the important technical and economic factors that must be considered.

Jan 1, 1987

By W. W. Adams

During the calendar year 1927 the United States Bureau f Mines conducted, for the third consecutive year, a safety contest among more than 250 mines and quarries. Aside from its underlying purpose to promote safety, the object of the contest was to learn which mine or quarry had completed the year's work with the smallest proportionate loss of time from accidents to its employees. Competing companies were grouped into five classes, namely, anthracite mines, bituminous teal mines, metal mines, nonmetallic mineral mines, and quarries and open-pit mines. To the winning company in each group was awarded the bronze trophy "Sentinels of Safety," the gift of The Explosives Engineer magazine. The winner in each group was the mine or quarry whose record showed the smallest loss of time from accidents in proportion to the total amount of time worked by 411 employees. This proportion is designated the "accident-severity"3 rate; it indicates the number of days of disability resulting from personal injuries per thousand man-hours of work performed by all employees. Each company's standing was determined by the Bureau of Mines from detailed records furnished by the contestants. Records of the leading companies were made known to a committee of seven men well known to the mining industry but not connected with the Bureau of Mines. This committee selected the winning companies in accordance with rules governing the Competition. According to the contest rules, the competition for the trophy was restricted to mines employing at least 50 men underground and to quarries and open-pit mines employing at least 25 men in the pit. As several plants fell below these figures during the year, their records could not be considered in connection with the award of the trophy. Figures covering these plants are, however, included in the attached tables.

Jan 1, 1928

By Wm. W. Odell

In distributing natural and mixed gas, the industry is each year confronted with the problem of manufacturing gas in increasing amounts as the supply of natural gas becomes more nearly exhausted. The manufactured gas is now used in mixtures with the still available natural product, and will subsequently be used straight as a substitute gas. The gases that might be considered, and are producible by tried and developed processes, include water gas, carbureted water gas, and coal gas. Singularly, these gases can be used in this manner in ordinary appliances only when proportional amounts of them in the mixtures do not vary beyond rather definite limits, unless burner adjustments are made. The limits are defined by the specific gravity, content of inerts, and burning properties of the respective gases. Anticipating a future standard for city gas lower than that of natural gas during the period when considerable natural gas is available, there is justification for considering the possibility of re-forming natural gas and making a product that has substantially the same properties as other gases which can readily be generated. This report gives the results obtained during a series of tests made under a cooperative agreement by the U. S. Bureau of Mines with the Ohio Fuel Gas Co., re-forming natural gas at Toledo, Ohio, in full-scale operation in a water-gas generator having a grate area of 25.1 square feet. ACKNOWLEDGMENTS The Ohio Fuel Gas Co. constructed a special water-gas generator for the tests and provided men and the necessary funds for its operation. Appreciation is expressed for the general spirit of helpful cooperation which was evidenced in the activities of all those who took part in the work. Particular acknowledgment is made of the assistance rendered by C. W. Wallace, manager, and by C. F. Cramer, superintendent, and A. Upp, foreman of the plant.

Jan 1, 1929

By A. L. Engel

As a part of the program of the Rare and. Precious Metals Experiment Station, Reno, Nev., in connection with investigations of treatment methods for precious and precious-base metal ores, to further conservation and recovery of precious and base metals, tests Were made on samples from the Buzzard Mine, located in the vicinity of Placerville, Calif. These samples represented ore exposed during previous development work, in tunnels and a shaft on the property, including highly oxidized material from the surface zone and sulfide ores from depths of 150 to 300 feet. The surface samples contained little base metal and only enough gold 80 that economic exploitation of them would depend on development of a large tonnage of ore, low-cost mining methods, and satisfactory treatment methods. The sulfide samples were valuable enough to warrant further exploration and development and, if present in suitable tonnage, the installation of a treatment plant for recovery of both precious and base metals. The oxidized surface-zone samples carried 0.11 to 0.14 ounce gold per ton. Standard amalgamation and flotation tests of these samples gave low recoveries. Standard cyanidation tests indicated high consumption of lime and cyanide and gold extraction of 79.4 and 82.7 percent. Water-leaching the ore after crushing to minus 10-mesh improved cyanidation considerably. Ex-tractions of 82.7 to 85.8 percent were obtainec1 with lime consumption of 6 to 7 pounds per ton of ore and cyanide consumptions of 1 to 4 pounds. Grinding the samples to minus 200-mesh followed by water-leaching and cyanidation gave improved extractions of 91-92 percent of the gold, but with slightly increased consumptions of lime and cyanide.

Jan 1, 1949

By A. E. Raddatz

The Federal Bureau of Mines, as part of its goal to minimize undesirable environmental impacts associated with mineral processing, has investigated a soda-smelting technique for processing ilmenite into pig iron and a titanium slag that is suitable for a feed to a sulfate-process titania pigment plant. By this procedure, the generation of ferrous sulfate waste and its associated disposal problem is obviated. Molten titania slag was quenched, water leached, and filtered to yield a sodium titanate intermediate product containing about 70 wt-pct Ti02, 1 wt-pct Fe, and 20 wt-pct Na20. This intermediate product, high-soda titanate (HST), was mixed with H2S04, calcined, quenched, and water leached to produce a low-soda titanate (LST) product that contained only 2 wt-pct Na20. Both the HST and LST were evaluated as feed materials for preparing titania by the sulfate process. About 95 pct of the Ti02 was extracted from HST and LST by digestion in concentrated or 50-wt-pct-H2S204 solutions. About 95 pct of the solubilized Ti02 was subsequently recovered from the titanyl sulfate solutions by hydrolysis. Barren solutions from hydrolysis, containing about 26-wt-pct H2S04, were upgraded by vacuum-thermal evaporation or electrodialysis. The regenerated acid solutions were used to digest additional HST and LST.

Jan 1, 1979

By X. Shi, N. S. Dala, V. Vallaythan

"Cellular damage induced by silica dust is known to be associated with increased fragility and destabilization or destruction of the cell membranes. The mechanism by which silica dust effects biological membranes is still unknown. Using the ESR spin-trap methodology, we find that hydroxyl radicals are generated in aqueous suspensions of freshly ground silica. The amount of the radicals generated depends on the extent of grinding and ""freshness"" of the dust. Using linoleic acid as a model lipid, we show that the silica dust causes lipid peroxidation via ·OH, 02-, or linoleic acid related radicals as intermediates. Catalase and superoxide dismutase inhibit the formation of these radicals. The results suggest that free radicals associated with freshly ground silica and the related lipid peroxidation of the memberanes may be the starting point of the silicotic processes.INTRODUCTIONDespite considerable-effort over the years, the mechanism by which the quartz particles exert their toxic action on cells and the process(es) by which these actions progress to fibrosis are still not fully understood (1,2). It is generally thought, nevertheless, that the interaction of the quartz particles with the cell membranes is the starting point of the silicotic process (3). We felt that the mechanism of the membrane damage by quartz might involve oxygenated free radicals because (a) a suspension of quartz particles in contact with alveolar macrophages has been reported.(4,5) to initiate an enhancement of lipid peroxidation, defined broadly as the ;oxidative deterioration of polyunsaturated components of lipids, and (b) hydroxyl (·OH) radicals are known to be capable of peroxidation by abstracting hydrogen atoms from cell-membrane lipids (6) and initiating lipid peroxidation in lysosomal membranes (7). Moreover it is known that exposure of cell membranes, fatty acids and unsaturated food oils to ionizing radiation, which generates ·OH. radicals, causes rapid peroxidation (6). Earlier studies o~ the aqueous chemistry of quartz suspensions have reported detection of HzOz (8), implicating the formation of ·OH radicals as transient species, but, we are not aware of any report of the detection of ·OH radicals in quartz suspensions and this provided the motivation for the present undertaking. Since it is known that, because of their high reactivity (hence short life time) in aqueous media, the ·OH radicals cannot be detected via electron spin resonance (ESR) directly (9,10), we have used ESR combined with the spin-trap methodology (9) for studying the •OH formation."

Jan 1, 1988

A construction material based on plasticized sulfur and mineral aggregate, that is superior in corrosion resistance and strength to portland cement concrete. The material can be used in the chemical, metallurgical, and fertilizer industries, and will also provide an attractive market for by-product sulfur resulting from compliance with pollution regulations. How It Is Made Sulfur concrete is thermoplastic material. Plasticized sulfur is mixed with sand and gravel aggregate heated to 375-400° F. The sulfur melts and acts as the binder or cement. The sulfur concrete is poured hot and sets at a temperature of 200° F. Full strength is attained in a few hours, compared to several days for portland cement concretes. Sulfur concrete even pours and sets in freezing weather. Although unmodified sulfur with aggregate will produce a sulfur concrete with good initial properties, it undergoes crystallographic modifications, and deteriorates with time, particularly when exposed to moisture or freeze-thaw conditions. The Bureau of Mines has developed plasticizers which, when reacted with the sulfur, give sulfur concretes with excellent moisture and freeze-thaw resistance. The plasticizers are based on mixtures of dicyclopentadlene (DCPD) and ollgomers of cyclopentadiene. About 5 percent by weight of the plasticizers is reacted with molten sui fur for several hours. The sulfur cement can be used directly or allowed to solidify for easier handling and storage.

Jan 1, 1981

By A. J. Kraemer

[During the past several years a great deal of discussion has centered around the question of the permissible limit of sulphur content in fuels for automotive and aviation motors. Under certain conditions of operation, sulphur in motor fuels causes the formation of corrosive substances which attach bearings, wrist pins, and other parts of engines. On the other hand, in making gas¬oline from certain stocks, the gasoline fraction normally contains a relatively large proportion of sulphur compounds. By the generally used processes of reducing the sulphur content, a significant part of the gasoline fraction is lost as motor fuel, and added expenses are entailed for chemicals, labor, and other process costs. This condition has been an economic burden to some refiners of high-sulphur crudes. In some instances the treating losses have been rather severe and the treating costs relatively high, but the data presented in this paper indicate that the reduction of sulphur content of motor fuel is a problem to a relatively small number of refiners and of little or no concern to the remainder; in fact, more then 90 per cent of the 153 samples analyzed passed the Federal specification requirement, which limits the sulphur content to 0.10 -nor cent. 3 This report is based upon the results of an examination for sulphur content, Doctor test, copper strip corrosion, and color of the samples collected during January, 1930, for the twenty-first semiannual gasoline survey of the Bureau of Mines. The results of the gravity and distillation tests of the survey were published as Report of Investigations 2995. The numbering of the samples given in this report is the same' as in Report of Investigations 2995; for example, No. 25 of this report is the same sample as No. 25 of Report of Investigations 2995.]

Jan 1, 1930

"There is considerable evidence that all mine dusts do not present the same health hazard. Rank of coal and composition, especially silica content of the mine dust, shape, and surface charge are risk factors that affect the incidence and severity of CWP. Current efforts of Center researchers involve characterization of:•,size/shape/composition•,surface and functional groups•,particle interactions.Work is underway to prepare and characterize respirable coal dust samples, and to develop and evaluate techniques and procedures for the characterization of respirable dust. A suite of standard samples including anthracite, medium volatile and high volatile bituminous coals, quartz, clay, and rock dust have been prepared and thoroughly characterized with respect to the distributions of particle size and compositions. A comparison of the morphology of the standard dust particles with similar particles collected in an underground coal mine is given in Figure 43. Samples of these characterized (Standard) dusts have been distributed among various research groups associated with the Center.The aerodynamic diameter of a particle is a particularly important characteristic since this parameter determines the point of deposition in the human respiratory tract. A 3-dimensional numerical model for theoretically determining the equivalent aerodynamic diameter of irregular shaped particles has been developed and used to analyze coal dust particles and a particle shadowing technique has been developed for .experimental 3-dimensional shape analysis (Figure 44). In the theoretical technique, the equivalent aerodynamic diameter of the particle is numerically determined from computation of the fluid drag on the particle. This allows the aerodynamic diameter of any regular or irregular shaped particle to be determined as a function of the particle's orientation or as an average over all particle orientations. The technique is quite accurate in that the aerodynamic diameter of several coal dust particles have been numerically determined to be within 5% of experimentally measured values."

Nov 1, 1988

After more than 20 years dependence on bituminous coal as a primary fuel for generating electricity, the Pennsylvania Power and Light Company initiated a one-year study on the economics of building an electric generating station using anthracite as a fuel. The study will be completed in December 1976. If the feasibility study so indicates, PP&L will consider installing four 400,000 kilowatt generating units for scheduled commercial operation in 1985. Each unit would consume up to one million tons of anthracite annually. Anthracite generally is more difficult and expensive to extract than bituminous coal, but it has a significantly lower sulfur content than the bituminous coal currently being used by PP&L, thereby eliminating the costs of installing sulfur emission controls at generating stations. Moreover, significant reductions in transportation costs may be realized because the utility's operating territory is situated in the center of the anthracite region in northeastern Pennsylvania. These advantages may indicate that the use of anthracite is more economical than bituminous coal to PP&L. ASBESTOS -Asbestos production in the U.S. dropped again in 1975 until it was just two-thirds of that in 1973. This was in spite of the very strong demand caused by the Quebec strike. The 7-month strike of the asbestos miners in Thetford Mines, Quebec cut off 55 percent of the normal supply of U.S. consumers. Apparent domestic consumption was less than 75 percent of that in 1974. The wage settlement will probably result in a 20 percent increase in asbestos prices.

Jan 1, 1975

By Leonard F. Heising

Domestic production of Metallurgical-grade manganese has contributed such a small percentage of the United States industrial demands that areas known to contain large tonnages of low-grade manganese ore have been investigated by the Bureau of Mines to reduce this country's dependence on foreign ores. A major source of low-grade manganese is the Cuyuna iron range in Minnesota. The entire Cuyuna iron range is covered by an overburden of glacial drift that, in some places, reaches depths of 200 feet or more. Prospecting and exploration must be guided by geophysical methods, drilling results, or projections of exposures found in operating mines because there are no outcrops near the productive parts of the range. Past drilling for the purpose of outlining iron ore generally was confined to the highly oxidized zones. Much of the manganese with which the Bureau of Mines is concerned occurs in thin-bedded unoxidized iron formations, too low in iron content to have been of interest to those seeking commercial iron ore. The primary objective of the core-drilling reported here was to obtain cores of different classes of manganiferous rocks and to determine whether or not the samples were amenable to beneficiation.

Jan 1, 1959

By T. M. Garland

This report presents a Bureau of Mines assessment of crude oil and associated gas production and reserves that would result from different drilling efforts in the lower or contiguous 48 States during the 1972-85 period. The drilling effort was based upon five growth rate assumptions from the 1971 level. Additions to crude oil reserves were computed for nine cases resulting from the use of three equations for findings per foot drilled and three constant revision factors. The results indicate that the United States will not become self-sufficient in crude oil production by 1985 and also illustrate the lead time required to reverse the decline in oil production. Discussion is limited to three of the nine cases to provide high, intermediate, and low results. More emphasis is on the intermediate case because it is indicative of the most probable trends. The methodology and statistical data are included in the appendices.

Jan 1, 1974

By Michael J. Brnich

On November 20, 1968, a massive explosion rocked the underground workings of Mountaineer Coal Co.?s Farmington No. 9 Mine in West Virginia. Of the 99 miners who were working in the mine at the time of the explosion, only 21 survived and escaped the mine. This group included eight who were rescued from the Mahan?s Run air shaft. Nearly 40 years after the event, researchers from the NIOSH Pittsburgh Research Laboratory conducted oral history interviews with two of the eight survivors rescued from the shaft. The Farmington No. 9 Mine disaster ultimately led to passage of the Federal Coal Mine Health and Safety Act of 1969 (amended in 1977).

May 1, 2009

By S. R. Wilson

[The Anniversary-Bucky pegmatite is one of the largest, dikes in the Quartz Creek district, 21 miles east of Gunnison, Colo. The major dike consists of quartz-albite pear pagmatite and graphic granite with many quartz masses as individual cores occurring within the dike. A mining operation on one of the largest core areas has exposed several mineralogic cones directly associate with the core. These zones, including the large- units of the dike, are quartz pegmatitc, quartz-perthite pegmatite, perthite pegmatite, muscovite-feldspar -quartz pegmatite, quartz-albite pegmatite, and perthite-quartz (graphic granite) pegmatite. Muscovite and beryl are found in the muscovite-feldspar-quartz zone and are the only two products that have been marketed. Other potential products are perthite, graphic granite, and possibly small quantities of columbite-tantalite, monazite, and related radioactive minerals. The Bureau of Mines drilled two diamond-drill holes during April 1950 to investigate the largest and cost promising core area. This, report describes the results of this drilling.]

Jan 1, 1953

By Jr. Allan

"Although the advantages of large-capacity air receivers for underground mines are plainly evident from published information about various installations in the United States and abroad, details of their construction are not generally known in this country., Ordinary present-day air-compressor installations servicing mining machines are designed to supply air at a specified pressure in sufficient quantity to meet the peak demand of the mine,2/ although this demand may exist for only a few minutes out of 24 hours and, as usually happens, eventually exceeds the capacity of the compressor. Most of the receivers provided with these compressors (to a certain degree of standardi¬zation) are capable of storing a volume of air approximately equal to that compressed in 1 minute by the machine.3, 4/ As a result, during peak-load periods the compressor operates at full load capacity without maintaining kick-off pressure. At other periods of the work cycle, production of compressed air is intermittent.At least one large mine5/ has adopted large-capacity receivers to reduce wear on its air-compressing system caused by the sudden demand of peak loads. Under the old system, the compressors jumped suddenly from half speed to full speed; boilers furnishing steam to the compressors were taxed heavily to provide the increased requirements of power; and machines using the air, among which were four large hoists, were required to operate at 65 pounds per square inch rather than at the 90 pounds per square inch for which the compressors were regulated. Operation of air machines, especially drills, at pressures lower than those for which they were designed decreases their efficiency and increases maintenance costs. In addition, air that comes directly from the compressors has had little opportunity to cool and dry enroute.6./ As a result, quantities of compressor lubricant and water are carried into the machines that use the air. When expansion occurs in the cylinder or turbine of such engines, the temperature of the air drops, and this oil and water is precipitated. The water washes away lubricating oils in the machine, causing poor performance and high cost of maintenance; the compressor oil, in addition to being a poor lubricant for compresed-air engines, exerts a corrosive action on gaskets and rubber hoses.7/Reduction of peak demands on air compressors by large receivers lowers power costs by establishing more nearly constant load factors,8/ and in some cases by permitting the use of smaller compressor capacity.8,9/Load factor is the ratio of average demand to maximum demand; a low load factor costs money.10/Elimination of high-peak demands raises the load factor by making the average and the maximum demand more nearly equal. Further savings may be made possible by large receivers where their use permits charging to be done at night in regions having lower power rates during that period.11/Where ordinary receivers are used, compressor breakdowns cause immediate work stoppages in the mine owing to lack of air. Similarly, the capacity of a large receiver has been known to permit uninterrupted work in the mine until the compressors have been returned to service.9/Large-capacity receivers, either steel-tank or underground rock-chamber, offer a practical solution of many existing problems by providing a sufficient reserve of compressed air within the pressure range required for efficient operation of machines to level off peak demands on the compressor. The com¬pressors operate when the demand has reduced the pressure in the receiver below the regulating pressure and until all air used from the receiver has been replaced. It has been found possible in at least two mines,8.9/ one of which the author has visited, to entirely eliminate one compressor and to obtain more efficient performance from the remaining one by the construction of an underground coal-chamber receiver.8/"

Jan 1, 1950

By Howard E. Parkinson

In 1969, new coal mine health and safety legislation was enacted in the United States. As a result of this legislation, the Department of Interior, Bureau of Mines has carried out communications research aimed at developing whole mine communications for increased safety and efficient operation. The research has advanced and many promising results are now being demonstrated to the mining industry. However, there remains a challenge to further improve wireless communications within the mine workings, and through the overburden above the workings. The objectives for future research and development will be discussed, together with the physical and operational constraints that new mine communication systems must face.

Jan 1, 1973