Search Documents

By Kenneth L. Cashddollar, Terry G. Montgomery, Eric S. Weiss, John E. Going

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRI, Lake Lynn Experimental Mine and after laboratory explosions in the PRL 20-L chamber and the Fike 1-m3 chamber. The dusts studied included both high and low volatile bituminous coals. Low temperature ashing for 24 hr at 515°C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as or higher than the initial incombustible content. The MSHA alcohol coking test -was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared to the initial dust loadings to determine the transport distance of dust during an explosion. All of these data will be useful in future forensic investigations of accidental dust explosions in coal mines or elsewhere.

By J. Gautam, T. Ong, W. E. Wallace, M. Keane, S. Xing, J. Harrison

"INTRODUCTIONOrganics extractable from respirable diesel exhaust soot particles by organic solvents have been known for some time to be direct acting frameshift mutagens in the Ames Salmonella typhimurium histidine reversion assay (Huisingh, et al). Upon deposition in a pulmonary alveolus or respiratory bronchiole, respirable diesel soot particles will contact first the hypophase which is coated by and laden with surfactants. To model interactions of soot and pulmonary surfactant, we dispersed soots in vitro in the primary phospholipid pulmonary surfactant dipalmitoyl glycerophosphorylcholine (lecithin) (DPL) in physiological saline. We have shown that diesel soots dispersed in lecithin surfactant can express mutagenic activity, in the Ames assay system using S. typhimurium TA98, comparable to that expressed by equal amounts of soot extracted by dichloromethane/ dimethylsulfoxide (DCM/DMSO)(Wallace, et al, 1987). Here we report additional data on the same system using additional exhaust soots and also using two other phospholipids, dipalmitoyl glycerophosphoryl ethanolamine (DPPE), and dipalmitoyl phosphatidic acid (DPPA), with different ionic character hydrophilic moieties. A preliminary study of the surfactant dispersed soot in an eucaryotic cell test system also is reported.MATERIALS AND METHODSSoots D4 and D6 were collected at two different times as scrapings from the exhaust pipe of a diesel tractor-trailer immediately after the engine was stopped. Surfactant dispersions were made by ultrasonic probe sonicating 25 mg of commercially obtained DPL, DPPE, or DPPA into 1O ml of O.85% physiological sterile saline (PSS) for 10 min at 40 watts power. For surfactant dispersions, 2.5 mg soot was mixed into 2.5 ml of the appropriate phospholipid dispersion. Mixtures were sonicated by 40 watts sonicator probe for one min, then incubated in the sonicator water bath for 30 min at room temperature; the mixture was then incubated for one hour at 37C while being rotated continuously. Dilution series were made with saline. For solvent extraction, 2.5 mg soot was mixed into 2.5 ml of DCM and incubated in a sonicator water bath for 30 min at room temperature. The sample was then mixed with 2.7 ml DMSO, placed in a dry bath at 45C, and the DCM evaporated under a stream of nitrogen gas until 2.5 ml of liquid remained. Ames salmonella/microsome assay utilizing TA98 for frameshift mutation was used for mutagenicity testing, with and without S9 activation, as described by Ames et al (1975). Unfiltered sample extractions or dispersions were preincubated with tester cells for 90 min at 37C : 0.1 ml of sample was mixed with 0.5 ml of PSS, or of S9 mixture, and 0.1 ml of an overnight TA98 culture incubated samples were then added to 2 ml of top agar supplemented with biotin and a trace amount of histidine, and overlayed onto Vogel-Bonner minimal media plates. After 48 hours incubation at 37C, revertant colonies were counted. Solvent controls were DMSO, DPL, DPPE, DPPA, and saline. Positive controls were trinitrofluorenone (1 ug/plate), for samples not treated with S9, and 2-aminoanthracene for S9 treated samples (2.5 ug/plate). All samples were assayed in duplicate. Sister chromatid exchange (SCE) assay was performed, following Lett, et al (1981), using V79 cells, of Chinese hamster pulmonary fibroblast origin. Stock diesel sample suspensions were made as 10 mg soot/ml DPL suspension, or 20 mg soot/ml in DMSO. Aliquots of these soot preparations were added to 15 ml of culture medium per sample flask to result in concentrations of 25, 50, and 75 ug soot/ml medium. After 12 hours incubation, 200 ul of 25 uM 5-bromodeoxyuridine (BrdU) was added to each flask. After another 35 hours incubation, 200 ul of 10 ug/ml colcemid were added; and the cells were harvested three hours later. Cells were swollen by hypotonic saline, and fixed twice with methanol/acetic acid, and burst on microscope slides. Cells on the slide were stained with Hoechst 33258, exp"

Jan 1, 1990

By D. S. Burgess

The characteristics of gas-phase detonations were observed in 20 instrumented firings within earthen tunnels, in 100 such detonations in a 24-in-diam by l63-ft-long steel pipe, and in about 200 smaller scale firings. Most of the fuels studied were representative hydrocarbons--acetylene, propane, gasoline, and a roughly equimolar mixture of methylacetylene, propadiene, and propane. In a pipe with two closed ends, the detonable limits were demonstrated to be very nearly the same as reported limits of flammability. The side-on impulses (pressures integrated over 200-msec intervals) were shown to be the same function of concentration regardless of whether deflagration or detonation had occurred. In a pipe with only the initiation end closed, the impulses of all fuel-air systems tended toward the same level when averaged over comparable ranges of fuel concentration; the lower pressures with saturated hydrocarbons were nearly compensated by longer durations of pressure transient. In all fuel-air systems, unexpectedly high impulses were obtained with slightly lean mixtures. In earthen confining structures, the impulse, of the explosion was efficiently converted into momentum of the failing wall. In the configurations studied, an earth velocity of about 20 fps was critical to overcome the soil's resistance to shear. The destructive effect was determined by gas pressure rather than by total energy release. The assignment of a "TNT equivalent" to an explosive gas mixture is discussed in terms of the confinement of the mixture.

Jan 1, 1968

By N. F. LeJeune, Earl C. Lane

This is the third of a series of reports on a survey of petroleum prod- ucts manufactured on the Pacific Coast from California crude oils. California crudes differ in many characteristics from the petroleum produced in the other parts of the United States, and the claim has been made that some of the present Federal Specifications for petroleum products tend to discriminate against Cali- fomia products. The purposes of the present survey are to determine what par- ticular specification requirements Califomia petroleum products characteristical ly fail to meet, how widely the products deviate from these requirements, and if possible to show whether the fault lies with the specifications or the products, or along what lines investigation to determine this question should proceed. The first report of the series gave the physical and chemical properties of the samples of gasoline and mineral spirits. A second report**, gave the physical and chemical properties of samples of lubricating oils. The present report deals entirely with burning and fuel oils. The refin ing companies have continued their very cordial and helpful cooperation. Seven samples of kerosene, four samples of Diesel fuel and eight samples of fuel oil were obtained. The methods of analysis used are those adopted by the Interdepartmental Petroleum Specifications Committee, published by the Bureau of Mines in Technical Paper No. 323. The specifications used for corparison are those officially adopted by the Federal Specifications Board for the use of the various Depart- ments and Independent Establishments of the Government, effective February 3, 1923, and published by the Bureau of Mines in Technical Paper No. 323, Part 1. Specific gravity, degrees A.P.I., viscosity and other special tests al- though not required by the specifications have been given for comparison. All temperatures are recorded in degrees Fahrenheit. Tables have been prepared giving data on physical and chemical propertios of the individual samples. Before each table the classification and specifica- tions for the particular class of oil considered in the table are given. Follow- ing each table, brief notes show wherein samples deviate from specification re- quirements.

Aug 1, 1923

By John P. Harmon

A group of organic chemicals, known as wetting agents, has been developed, primarily for use in the textile industry. These chemicals have the property of reducing the surface tension of water when mixed with it in very dilute solutions. The advantage of lowered surface tension is recognized in dust-control work, and several wetting agents, have been tried by dust-control engineers with varying degrees of success. It is well-known that certain solids, coal for instance, are extremely hard to wet with plain water because of the high surface tension of water and the water-repellent action of coal. If the surface tension of the water is reduced, it can be demonstrated that the coal can be wetted easily. This is accomplished practical and at law cost by dissolving a very small percentage of wetting agent in the water that is to be used for wetting purposes. (Care should be exercised in using a wetting agent to be sure that it will not interfere with a subsequent process.) For some time, the comparative efficiency of various wetting agents has been the subject of considerable work by dust-control men at coal mines, as well as by members of the Bureau of Mines 3/, 4/, 5/, 6/. In this connection, a number of samples of air-borne dust have been collected in the mines. With the exception of dust-control measures conditions of dust generation and dissemination were maintained as, nearly uniform as possible. Samples were collected when water alone was sprayed on the cutter bar of a mining machine; various wetting agents were then successively added to the water and more samples of air-borne dust were-collected.

Jan 1, 1946

By M. R. Geer

All the coal lands in Alaska are publicly owned, and the Federal Government is the principal consumer of coal. Therefore the Government has long been concerned with the wise utilization of the coal reserves of Alaska as well as with the availability of coals meeting the specifications for use in various Government installations. Coal preparation plays a key role in both of these areas of interest. The proper choice and operation of coal-washing equipment permits the mining of inferior deposits, minimizes waste of coal in preparation, and assures a prepared product of the best quality obtainable from the raw coal. Thus, from time to time, the Bureau of Mines has made washability examinations on most of the coals mined in Alaska. Generally, these examinations were made when new mines or new beds were opened, when construction of new preparation plants was being considered, or when the operation of existing plants could be improved by better knowledge of the raw coal. The purpose of this report is to bring together all the washability data available on the coals of the Matanuska Valley and Beluga River fields. The pattern of energy development for the rapidly growing Anchorage area is not clear at this time. Formerly coal was the only fuel available for large-scale space heating and power generation. More recently both oil and natural gas have entered the market, and several hydroelectric projects have been completed. Additional major hydroelectric projects are being considered. The role that will be played by coal in this competitive energy market is uncertain. However I if coal is the fuel used in future power plants or industrial installations, the information contained in this report will be useful in indicating the quality of the coals that can be supplied and in selecting proper preparation techniques.

Jan 1, 1962

By J. E. Tiffany

"The new permissible blasting device, Cardox, utilizes as a blasting agent liquid carbon dioxide which is discharged.as a gas from a steel container or shell. The loaded shell is placed in a borehole, stemmed, and tamped in a manner similar to that employed with explosives, and is fired by electricity.The Bureau of Mines' approval for use of the device in coal mines was granted as Approval No. 1 under date of October 3, 1928; as the result of tests made under the conditions and requirements of Schedule 20. There have been three subsequent extensions whereby minor modifications in the original design were granted.The permissibility of the device is subject to the following conditions; (1) It shall be in all respects similar to the sample submitted for tests; (2) certain thicknesses of disc and. weights of heater ingredient and of carbon dioxide, all of which are set forth in Table 2 under the provisions governing permissibility, must be used: (3) the rear cap must always be in place after the shell has been charged, to prevent accidental firing; and (4) firing must be done by means of a permissible-type blasting unit.The permissibility of Cardox was established by gallery tests similar to those used in testing explosives for permissibility. In these tests the shell was discharged into gallery 1 without causing any ignition of gas and air or of gas, dust, and air mixtures there. The conditions of charging the shell, such as weight of the ingredients of the heater element, the carbon dioxide charge, and thicknesses of the disc, were varied according to the conditions under which it would be likely to be used in blasting. The tests made in gallery 1 are here described in detail, as are also the tests which have been made for determining the propulsive strength of the device and the quantities of poisonous gases given off when a shell is discharged."

Mar 1, 1929

By Edward F. Divers

A new nonclogging water spray system for continuous-mining machines has been developed under contract with the Bureau of Mines. This paper presents installation and operating guidelines for the system, which consists of improved and easily maintained machine-mounted hardware, including an inline Y-strainer, a hydrocyclone, a backup filter, and two quick-opening valves for flushing particulates from the strainer and hydrocyclone. Underground tests with continuous-mining machines have shown that when properly installed and maintained, the new sys tern virtually eliminates nozzle clogging and thus greatly reduces spray maintenance. The sys tern is relatively inexpensive and has been installed on typical continuous-mining machines for a total cost under $1,000.

Jan 1, 1976

By F. W. Brown, F. C. Gibson

"INTRODUCTION There is urgent need for a satisfactory permissible multiple-shot blasting unit capable of firing 10 detonators in series and safe for use in underground mining where a. gas-ignition hazard may exist.. As there is at present no entirely satisfactory permissible unit of either the battery or generator type, tile described capacitor-battery type has been developed. Consideration of the Bureau of Nines approval schedule pertaining to the generator and magne to-type units and of the electrical characteristics of the unit described in this report indicate that this unit should meet Bureau of Mines permissible requirements.This report gives a detailed description of the design and operation and results of tests to determine safety of operation in gassy atmospheres.DESIGN AND OPERATION OF UNITOperation of the vibrator-type multiple-shot blasting unit is based upon utilization of the discharge energy from a capacitor charged to a given. voltage and having capacitance adequate to store enough energy to initiate 10 detonators in series. The primary source of energy is a 4-volt cap lamp battery such as is carried for illumination on the person of underground workers in nearly all mines. As this battery is already available and is recharged daily it is considered to be a reliable and convenient source of energy for a blasting unit. Figure 1 is a schematic diagram of the circuit for an improved unit, and figures 2 and 3 are views of the experimental unit. The battery potential is applied through a radio-type synchronous vibrator (8) to an 8-volt center-tapped primary of a small transformer (9) having a high-voltage center-tapped secondary. The vibrator introduces an alternating low-voltage potential into the primary and mechanically produces full-wave, rectified, pulsating, direct current from the secondary. A buffing condenser (11) across the secondary gives the proper wave form for long vibrator life: a resistor (12) its in series with this condenser across the total secondary to protect the transformer in case of• failure .of this capacitor. A voltage divider (10) with an adjustable slider permits accurate adjustment of the potential applied to the high-capacity firing condenser (5)."

Oct 1, 1947

By V. R. Miller

The Bureau of Mines has developed a technique to separate and recover the three major components, Pb, Zn, and Cd, from lead smelter flue dust. This research was conducted as part of the Bureau's effort to reduce environmental conflicts and occupational hazards associated with mineral-processing operations and to recover valuable constituents in emissions and effluents. The laboratory process utilizes sulfation roasting of the flue dust followed by water leaching to extract over 95 pct of the cadmium and zinc. Ninety-nine percent of the cadmium was recovered from solution by cementing with zinc dust, and zinc was electrowon from the resulting solution after purification. Zinc electrolysis was carried out in a 1-liter cell at 35° C with a cathode-current density of 8 A/dm2 in a solution containing 65 g/l Zn++ and 180 g/l H2S04, Current efficiencies of 80 pct were obtained. The leached residue consisted largely of PbS04, which was converted to PbC03 and leached with H2SiF6 to produce PbSiF6 electrolyte. Ninety-five percent of the lead contained in the residue was converted to electrolyte. Lead was electrowon from solutions containing 70 gil Pb++ and 90 g/l H2SiF6 using a lead cathode, Pb02-coated titanium anodes at 28° C, and a current density of 1.6 A/dm2. Current efficiencies approaching 92 pct were obtained. Accessory minerals such as cobalt and nickel were separated into purification residues and liquor.

Jan 1, 1982

By Eugene V. Cilento, R. Clark Lantz, K. A. DiGregorio

"This laboratory bas developed a sensitive electro-optical method to quantify the initial rate (R) and total amount (MAX) of superoxide (02) produced by single pulmonary alveolar macrophages (PAM). The method uses a microscope-based TV system to visualize PAM in culture, and to video record the images during the time the cells produce 02. MAX and R are calculated from measurement of temporal changes in optical density in the images due to precipitated diformazan formed by the reaction of O2-, produced by each PAM, with nitroblue tetrazolium present in the culture medium. To date, values of Rand MAX, measured due to adherence of PAM to the dish, have been compared to values obtained when quartz, coal mine dust (CMD), and kaolin . were added to the medium (in vitro). Rand MAX have also been calculated for PAM lavaged from animals exposed to quartz and CMD in the WVU Inhalation Facility. Presently, experiments are being done using which will permit PAM to be restirnulated by different dusts to help establish a dose response relation~ p and a means to study the role of lung surfactant on modifying the acute toxicity of inbaled dusts. Ultimately, this methodology should provide useful insight into establishing the role of 02 in PAM dysfunction due to inhalation of dusts, and in lung diseases such as pneumoconioses. INTRODOCTIONPAM are free cells found in the lungs which protect the lungs by removing foreign debris and bacteria. This is accomplished, in part, by the process of phagocytosis, whereby foreign matter is internalized into vesicles known as primary phagosomes. Phagocytosis also involves the chemical breakdown of inhaled dusts and the killing of microbes. Detoxification is aided by the respiratory burst, which is a metabolic response of the cell to foreign substances, that results in the production of highly reactive oxidizing agents from the partial reduction of extracellular oxygen to superoxide (02) at the surface of the plasma membrane. Superoxide undergoes either spontaneous or enzyme catalyzed dismutation reactions to form hydrogen peroxide (H202) and subsequently hydroxyl radical (OH•) and singlet oxygen (02 t ). However, while these oxygen metabolites aid in the killing of microbes they also may destroy endogenous tissue. For example, 02 has been linked to the aging process and to many diseases including emphysema, diabetes, and cancer.'' Therefore, a better understanding of the production of 02 is extremely important since an abnonnally low production could result in damage by inhaled dusts and bacteria while an abnormally high production could result in direct damage to the lung tissue by the phagocytes. Inhalation of respirable sized mineral dusts, such as quartz (silica), coal mine dusts (CMD), and asbestos, results in various pulmonary disorders. PAM are thought to play an important role since evidence suggests that the first step in fibrogenesis is an interaction of dust particles with PAM. Generally, in vivo exposure of animals to mineral dusts results in increased respiratory burst activity, migratory patterns, phagocytic behavior, and secretory potential of PAM, and for this reason these have been implicated to be pivotal events in the pathogenesis of pulmonary diseases.1 In addition to stimulation of resident PAM, an influx of monocytes into the lung and/or production of new macrophages generally occurs in response to fibrogenic dust inhalation. Further, PAM may attract and stimulate fibroblasts, which normally synthesize proteins and collagen during rep~ of tissue, by secreting chemoattractants and enzymes. Thus, PAM may be involved in pulmonary disorders through failure or partial loss of their defensive capability, or indirectly, through release of other mediators."

Jan 1, 1990

By Helen E. Edwards

The Bureau of Mines is engaged in a systematic evaluation of the thermodynamic properties of combustion gases. These studies are designed to provide basic thermodynamic information of high accuracy facilitating the theoretical study of flame and combustion phenomena. This report is the third of a series3/ presenting results of the study for particular fuel-oxidant systems. The equilibrium composition of the products of combustion and the adiabatic flame temperatures of specified oxyacetylene systems have been computed.

Jan 1, 1953

By I. F. Avery

The productive capacity of natural gasoline and cycling plants in the United States on January 1, 1956, was 46.4 million gallons per day, according to the Bureau of Mines r biennial survey. This represented an increase of 7.5 million gallons per day during the 2-year period since the last survey. In the previous 2-year period, capacity had increased 4.8 million gallons per day. The total number of plants increased from 535 on January 1, 1954, to 600 on January 1, 1956. The number of operating plants increased from 521 to 571. The major increases in capacity took place in Texas, Louisiana, New Mexico, and Oklahoma, with the absorption-type plants continuing to account for most of the new construction. All types of plants showed construction gains with the exception of charcoal which showed no change.

Jan 1, 1957

By J. A. Sutton

In connection with, a stream-pollution-research project, a colorimetric method was developed for concentrations of 1 to 30 p.p.m, of pine oil in water. The method depends on the stable bluish-green color produced when pine oil is reacted with vanillin-hydrochloric acid reagent at 60° C. for 25 minutes. The colorimetric reaction actually determines alphaterpineol, the principal component in pine oil. Some waters may require a special preparation in which ion-exchange resins are used to remove interference. ACKNOWLEDGEMENTS The author wishes to express his appreciation to A. A. Berk, chief of the Industrial Water Branch, Bureau of Mines, for helpful advice and encouragement during the progress of this work and to B. P. Martinez, chief of the Stream Pollution Research Section, for assistance with the manuscript. Thanks are also due to W. D. Bishop of the Hercules Powder Co., Wilmington, Del., for supplying the principal components of pine oil.

Jan 1, 1953

By Donald A. Voigt

This publication is intended as a guide for persons responsible for obtaining classifications and approvals Tor explosive compounds, mixtures, or devices from the U.S. Department of Transportation (DOT). It deals with the procedures for obtaining a recommendation for classification of an explosive compound, mixture, or device through the Bureau of Mines. Completion of the procedures detailed in this guide is necessary to obtain a final classification of an explosive compound, mixture, or device and assignment of an "EX" number by DOT, which will allow the producer to offer the explosive for shipment within the United States. This guide also gives procedures for obtaining United Nations (U.N.) classification for shipping outside the United States.

Jan 1, 1990

By John H. Hild

The topography of the Jamestown fluorspar area is rough and ranges from 6,400 to 8,000 feet in altitude. Some fluorspar was mined as early as 1870, but mining really did not begin in earnest until 1940, and up to July 1947 it is estimated that 272,500 tons of fluorite was mined and milled. In 1947 the General Chemical Co. was mining fluorite and milling it in a 200-ton-a-day mill at Valmont, 7 miles east of Boulder, and the Ozark-Mahoning Co. was milling ore in a 100-ton-a-day mill at Jamestown, using ore mined, by H. M. Williamson & Son. These fluorite deposits comprise veins in a granite country rock. The Bureau of Mines drilled eight holes, aggregating 2,579.1 feet, on the Blue Jay vein; four holes, aggregating 1,434 feet, on the Chancellor; and one 350-foot hole on the Nations Treasure. Fluorite of a minable grade and width was found in 10 of the holes drilled. In this report the location and accessibility, physical, features and climate are described and a brief history of the district is given. The deposits and character of the ore and sampling and analyses are described, mine workings are outlined, and work performed by the Bureau of Mines is summarized. Diamond drill logs are shown in appendix I, and 'Sample analyses are tabulated in appendix II.

Jan 1, 1949

Lower the respirable dust exposure of longwall shearer operators by isolating and con-fining the dust cloud near the face. Approach Install conveyor belt screens at various locations on the body of the shearer to contain and hold the dust cloud toward the face side of the machine. This approach provides a cleaner air split in the walkway, over the shearer operators. How It Works On most longwall shearer sections, the dust exposure of the shearer operators is primarily attributable to the machine it-self. The dust cloud originates at the face, and the exposure of the operators depends largely on how quickly this dust spreads into the walkway. Conveyor belt screens placed on the gob side of the body of the machine can reduce the amount of dust which spreads out into the walk-way. In addition, belting may be installed over any open spaces between the shearer under-frame and the panline to prevent conveyor dust from boiling out into the operator's walkway.

Jan 1, 1981

By Phillip R. Moyle

In 1985 the U.S. Bureau of Mines evaluated the mineral resources of the Sheep Creek West Wilderness Study Area (ID-111-36A), Owyhee County, ID, for the U.S. Bureau of Land Management. The Wilderness Study Area consists of 11,680 acres centered approximately 20 miles south of Grasmere, 10. It contains no mines, claims, or prospects. No mineral resources were identified; however, a geode occurrence within and adjacent to the Wilderness Study Area, and minor amounts of placer gold along Sheep Creek, may be of interest to rorkhounds and recreational gold panners.

Jan 1, 1986

By Albert A. Munsch

The Munsch National First-Aid Instructors Association had its inception during the teaching of a Federal Bureau of Mines first-aid instructors' class at McPherson, Kans., under a cooperative plan of first-aid training. Upon completion of- the course on July 1, 1938 members of the class organized the charter chapter of the association under the name of McPherson (Kans.) District Charter Chapter No. 1. On July 1, 1941, 3 years after the founding of the association, there were 15 chapters in the national council -7 in Kansas, 3 in Oklahoma, 2 in Texas, 2 in New Mexico, and 1 in Arkansas. Although the pioneer work of the association was done in the petroleum industry, the plan will be of even greater benefit to a district in which there are various types of plants, mince, and operations of the mineral and allied industries. ACKNOWLEDGMENTS The writer appreciates the cooperation and assistance of the following persons: S. P. Redfearn, safety engineer, Globe Oil & Refining Co. and affiliated companies, Wichita, Kans., and H. (Chief) Moore supervisor of safety meetings, Shell Oil Co., Inc., McPherson, Kans., for their untiring efforts and enthusiasm in organizing an- attending the first class, organizing three other classes, and helping to plan the work of the association

Jan 1, 1942

By Frank D. Lamb, D. A. Woodard

"INTRODUCTION The iron-ore deposits near Cranberry, N. C., were worked as early as 1820, and records show that to date at least 1,500,000 tons of ore has been mined.. The early operators depended on selective mining and hand cobbing to yield a product containing 40 to 50 percent iron. Later, a magnetic concentrator was erected by the Cranberry Furnace Co. and was operated periodically until 1930. The magnetic cobbing method employed yielded satisfactory concentrates, but the plant was shut down because costs were too high. 4/Early in 1944, in connection with the sponge-iron program of the Bureau of Mines, North Carolina and Tennessee were surveyed for the purpose of finding a readily available source of high-grade iron ore for use in the experimental production of sponge iron at Salisbury, N. C., and samples from various sources were tested in the laboratory. The Cranberry ore proved to be best with respect to grade of magnetite concentrates produced, and it was decided that a pilot mill should be built on the Cranberry mine property and that the concentrate made there should be shipped to Salisbury for direct-reduction tests in a commercial brick kiln."

Dec 1, 1946