Search Documents

By Paul H. Mutschler

The Bureau of Mines sponsored a study of the impact of changing technology on the demand for metallurgical coal and coke to 1985. Individual technologies were analyzed to determine what effect each had on the demand for and the consequent consumption of metallurgical coal and coke in the steel industry. The domestic steel industry demand for metallurgical coal and coke for the production of hot metal will probably increase through 1985. Formcoke if implemented on a worldwide basis could begin to supplant the U.S. export market for metallurgical coal. The major technologies that have contributed to the decline in demand for metallurgical coke per ton of hot metal are (1) the increased usage coupled with higher iron content of agglomerates, (2) modification of blast furnace practices such as high top pressures and blast temperatures, and (3) increases in the injection of supplemental fuels. The projected demand for metallurgical coal and coke under current technology for 1985 are 109.4 and 76.0 million tons, respectively. With future technology implemented, the demand for metallurgical coal and coke will be 82.0 and 56.9 million tons, respectively. The projected domestic demand for metallurgical coke could further decrease by as much as 15 to 20 million tons by 1985 if formcoking proves technologically and economically feasible.

Jan 1, 1975

By R. A. Isberg, D. A. Parrish, H. Kramer

This report describes the design and implementation of UHF radio and closed-circuit television systems in the Black River room and pillar limestone mine near Butler, Pendleton County, Kentucky. Prior to designing the radio system, measurements of signal attenuation on 812 and 466 mHz were made in the slope tunnel and in the straight and level crosscuts in the mine. Two distributed antenna systems fed by two sets of base stations provide approximately 75% coverage of the mine. Passive reflectors are used for extending signals into intersecting crosscuts and two-way signal boosters will be used to extend signals to the perimeter and obstructed areas of the mine. Fourteen mine vehicles were equipped with mobile radios equipped with digital identification, alarm and status encoders. Fifteen portable transceivers also were used. Six closed-circuit television cameras provide surveillance of critical transfer points of the belt conveyor system, and the loading dock at the base of the slope and an ash disposal area in the mine. Two-way radio communication and closed-circuit television have saved considerable man. hours, increased production, reduced maintenance costs and enhanced safety. Innovative developments were the use of passive reflectors and two-way signal boosters for extending signals into intersecting crosscuts, development of lightweight signal margin measuring equipment, modifications of mobile digital encoders to automatically send status information from mine vehicles such as numbers of loads of ore delivered, hot engine, etc., and the use of CATV technology for multiplexing audio, digital and video signals onto coaxial cables from the surface to the mine.

Jan 3, 1981

By John Nagy

Large-scale tests in the U.S. Bureau of Mines Experimental Coal Mine show that the explosion hazard of coal dust on shuttle-car roadways can be con-trolled by proper application of water, dry rock dust, a saturated solution of ammonium phosphate, or mixtures of water or the water-phosphate solution with rock dust. The experiments were made with loadings of 1.0 and 5.0 pounds of mine size coal dust per linear foot of entry, and with a 3-or 4-inch-thick layer of coal rubble on the floor, The data from the tests with mine-size coal and rubble are comparable. The water contents of the dust loading were determined from samples collected just prior to initiation of a gas-air mixture in an ignition zone at the face Dust samples were collected 1 inch deep from the coal-rubble deposit. One experiment was made with the dust in the coal rubble bound with latex applied as a water solution by spray. The binding action was inadequate and explosion propagation was obtained.

Jan 1, 1970

To provide longwall operators with a method to predict methane emissions from panels with increased face width.

Jan 1, 1997

By E. Morrice

The Bureau of Mines investigated methods for beneficiating platinumgroup metal ores from the Stillwater Complex , Montana , as part of its program to increase the supply of critical and strategic minerals and metals from domestic resources . This report presents results of a 5- day continuous campaign employing a pilot flotation mill to recover sulfide concentrate containing platinum- palladium values from anorthositic ore . A mercaptobenzothiazole - sulfuric acid reagent suite was used . The pilot flotation mill was operated at an average feed rate of 106 lb/ hr of ore . A rougher concentrate containing 8.5 pct of the feed was prepared ; it assayed 1.1 oz /ton Pt and 3.5 oz / ton Pd . Recovery of platinum and palladium were 91 and 87 pct , respectively .

Jan 1, 1965

By William A. Beck

Since bauxite mining began in the Irwinton District, Wilkinson County, Ga., in 1912, it has been on a small scale, as most of the deposits of high-grade ore are small. The bauxite has a high silica content, and its use has been largely limited to the chemical industry. Drilling under this project did not disclose any bauxite deposits of commercial value: However, numerous holes penetrated high-alumina clay deposits, but no attempt was made to delimit them, as the project was solely an exploration for bauxite. Bauxite was first discovered near Irwinton in 1907. The district covers virtually all of Wilkinson County and extends into the adjoining counties of Washington, Baldwin, and Twiggs. Mining was begun in 1912 by the Republic Mining & Manufacturing Co. on the Honeycutt, Parker, and Daniel properties, which are 1.5 miles from Wriley on the old Irwinton to Milledgeville Road.

Jan 1, 1949

By Jr. Watts, B. K. Cantrell, D. H. Carlson, K. L. Rubow

"Abstract — The use of diesel equipment in underground coal mines is controversial because the National Institute for Occupational Safety and Health (NIOSH ) regards ""wholediesel exhaust"" as ""a potential occupational carcinogen."" Threshold limit values (TLVs ) are recommended for the gaseous pollutants CO, CO2, NO, NO2, SO2 and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sample these aerosols.The University of Minnesota and the USBM have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) that utilizes size selective, partial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines that used diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine a quality.Air quality data were collected in four underground coal mines. The mines used continuous miners and diesel haulage equipment. Daily samples were collected at the section intake, haulage way and on haulage vehicles. Both full- and partial-shift samples were collected using a variety of aerosol instruments. These included the PDEAS and the micro-orifice uniform deposit impactor (MOUDI) that sample the mine aerosol diesel exhaust fraction. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust CO,CO2, NO, NC, and SO2. These measurements were made by either collecting bag samples for subsequent gas analysis or by Palmes dosimeters.Concentrations of CO, CO2, NO, NO2 and SO2 were well below regulated levels. The mine average DEA concentration determined by the PDEAS in the haulageway for the three mines surveyed was 0.79 mg/m4, with a standard deviation of 0.19 mg/m3 DEA contributed 65% of the respirable aerosol, at this location. These results were the same as the mean DEA concentrations calculated from size distribution measurements obtained using the MOUDI. This was 0.78 mg/m3, with a standard deviation of 022 mg/m3."

Mar 1, 1992

By James W. Miller

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and from the data developed, to determine: (a) Which coals either as mined or after beneficiation by conventional preparation are chemically suitable under present standards for producing metallurgical coke; (b) Which coals require special and more intensive treatment in preparation than is now practiced; and (c) Which coals cannot be considered potential sources of metallurgical coke, regardless of preparation. This report is one in this county series that describes the preparation characteristics of the coals of Perry County, Ky.

Jan 1, 1956

By O. C. Blade

This report on the properties of aviation gasolines and aviation jet fuels produced in the United States during 1954 was made under a co-operative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. Analytical data are presented for 101 samples of aviation gasoline. Data also are given for 30 samples of aviation jet fuel. The analyses were made on samples typical of the manufacturers I 1954 production in their laboratories and the results submitted to the Bureau of Mines for compilation. The products of 19 manufacturers of aviation gasolines and of 15 producers of aviation jet fuels are represented.

Jan 1, 1955

By Richard J. Bielicki

The possibility of replacing the brattice cloth closest to the coal mine working face with an air curtain mounted on top of a continuous-mining machine or with a diffuser fan was explored by the Bureau of Mines. Preliminary tests conducted at a full-scale model working face with the brattice end set at 18 feet showed that the air curtain improved face ventilation only slightly and was not nearly as effective as placing the brattice at 10 feet. A 2,000-ft3/min diffuser was more effective than the air curtain. It is concluded that the air curtain probably could not function as a line brattice extension, although the diffuser fan may have some potential.

Jan 1, 1975

By D. T. Hahn

Adequate and cost effective erosion control is an important component in most plans for reclamation of surface mined land. Despite the fact that much is known about erosion of agricultural lands, insufficient conclusive knowledge is available about erosion of reclaimed surface mined land. Our study was conducted to characterize the erodibility of reclaimed surface mine land relative to unmined cropped land, and to evaluate the accuracy of the universal soil loss equation (USLE) in estimating erosion from reclaimed soils. A rainfall simulator was used to measure runoff and erosion rates from plots at three Indiana surface mines. The relation of erosion of the reclaimed soils was not completely constant with that from the cropped soils. Significant differences in erodibility were observed between reclaimed and nonreclaimed top soils, as well as reclaimed topsoils and reclaimed subsoils.

Jan 1, 2011

By E. L. Garton

The Bureau of Mines for a number of years bas been conducting an investigation of crude petroleum from producing fields in the United States and the Western Hemisphere and has published a series of reports on these fields. Analyses of crude-oil samples from many oil fields of Oklahoma are given in Bulletin 2915. Analyses of 21 representative crude oils from various producing zones of the Oklahoma City field are given in this report. A close study of the analyses reveals very few differences in the general characteristics and chemical properties of these oils.

Jan 1, 1932

By J. M. Stuve

The present Bureau of Mines investigation measured low-temperature heat capacities of NiBr2 (8 to 302 K) and NiS04 (9 to 70 K) by adiabatic calorimetry. The standard entropies (S°, 298.15 K) of NiBr2 and NiS04 were calculated as 29.26 ± 0.06 cal/deg mole and 24.21 0.04 cal/deg mole, respectively. (1 cal = 4.1840 joules.) Heat-of-solution measurements of anhydrous NiBr2 were used to determine its enthalpy of formation (?Hf°, 298.15 K) as -50.64 ± 0.31 kcal/mole. High-temperature enthalpies of NiBr2 and NiS04 were measured by drop calorimetry to 1,150 K and 1,002 K, respectively. Enthalpies, heat capacities, and related formation functions are tabulated to 1,200 K.

Jan 1, 1978

By Ralph L. Windrow

This paper is one of a series being prepared for and published by the United States Bureau of Mines describing methods and costs of mining and preparing sand and gravel for market at various plants throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. The Clowdy plant, with which this paper deals, is located 7 miles west of Dallas, Tex., and has a rail connection with the Texas and Pacific Railway. In addition to the rail outlet there is a paved road over which materials produced at this plant can be moved into Dallas by truck.

Jan 1, 1932

By S. P. Kinney

Economy in blast-furnace practice depends largely upon efficient gas-solid contact in the shaft of the furnace. If efficient work is not done in the shaft the hearth and bosh will not function properly. A condition may be readily imagined where the particles of ore in the shaft are so large that the time entailed in the descent of these materials into the bosh is not sufficient to permit proper reduction and preparation prior to the time the ore enters the bosh of the furnace. Another condition may be pictured where the density of the stock column and the flow of stock is such that the ore will take one course and the gas another. Both of these examples will result in insufficient contact between the gas and the ore. Unreduced ore will reach the hearth, and gas which has not been efficiently oxidized will reach the stock line. The result is the use of an excess of carbon in the smelting process. An example of the result of inefficient gas-solid contact in the shaft of a blast furnace is shown by the curves in Figure 1.

Jan 1, 1930

By E. D. Calvert

As part of its goal to minimize the requirements for critical and strategic minerals, the Bureau of Mines is conducting research to foster the use of domestically abundant materials such as molybdenum. This report describes the development of an investment shell molding technique that can be used to make castings of molybdenum and its alloys. The mold material is cubic Zr02 with a monoclinic Zr02 binder. The shell, formed by standard investment molding techniques described in the text, is prepared for molybdenum casting by firing for 6 hours at 1,550° C (2,822° F) or for 4 hours at 1,650° C (3,002° F). The resulting castings have predictable and reproducible dimensions with good detail. As-cast strength is poorer than the strength of wrought materials below 1,600° F. At and above this temperature, tensile strengths of cast and wrought materials are nearly equal. Aqueous corrosion of the castings in most media is insignificant.

Jan 1, 1982

By H. B. Brunot

On April 26, 1949, the Bureau first approved a machine designed to replace the cycle of cutting, blasting, and loading coal by a single operation. This machine took the coal directly from the solid face and delivered it to transportation equipment. By January 1, 1955, 30 approvals for designs of machines of this type had been granted by the Bureau. In the main, this paper describes briefly the action of the various designs approved as permissible. In addition, the approval number, the date of approval, the voltage of the power supply, the number and character of the explosion-proof accessory parts, the size of the trailing cable, and the overcurrent protection at the outby end of the trailing cable are given for each design. Since no similar information has been published by the Bureau, it is hoped the material in this paper will be valuable in giving the mining public an organized look at the various machines of this nature that have been approved as permissible by the Bureau.

Jan 1, 1956

By Errol D. Sehnke

This U.S. Bureau of Mines report provides detailed information on worldwide bauxite production capacity by mine and country, including bauxite substitute materials in countries of the former Soviet Union, The information was compiled from a variety of domestic and international sources and was based on information available to the Bureau through December 31, 1994. Capacity data represent announced installed and planned capacities and do not necessarily reflect a U.S. Bureau of Mines judgment of actual mine operating levels or timing of planned expansions. The year-end capacity is the ?in place? capacity or estimated production capacity, whichever is larger.

Jan 1, 1994

By L. B. Berger

Each winter brings its toll of deaths and serious accidents from the deadly gas, carbon monoxide. Newspapers carry warnings to the public of the dangers of this gas, and frequent now items retort the finding of persons dead or unconscious from the effects of carbon monoxide, yet these accidents continue. Either those warnings are not read, or they are unheeded by people who feel that "It can't happen to me." It can happen to you - carbon monoxide is no respecter of persons, as evidenced by items appearing daily in newspapers all over the country. Carbon monoxide has been a threat to human safety as long as man has used fire to keep himself warm and to cook his food. The burning of any fuel that contains carbon may produce carbon monoxide. This is true of solid fuels such as coal, coke, and wood; of liquid fuels such as oil, gasoline, and kerosene, and of gaseous fuels such as natural or manufactured gas. In the process of combustion the carbon in the fuel unites the chemically with tat oxygen of the air to form carbon dioxide (CO2), however, if the supply of air is not adequate, combustion is incomplete and carbon monoxide (CO) will be formed.

Jan 1, 1943

By A. W. Fahrenwald

As an aid to studies of grinding, a batch laboratory classifier and elutriator has been developed at the U. S. Bureau of Mines Metallurgical Field Office at Moscow, Idaho, in cooperation with the University of Idaho. It is designed for use in conjunction with other batch laboratory apparatus, such as ball mills and flotation machines. It is shown in Figure 1. Description and Operation of Batch Laboratory Classifier The classifying column is a cylinder 4 feet 2 inches long, of 5 3/4-inch inside diameter, and terminates at its top in a cone or funnel 18 inches in diameter at the overflow elevation. The pressure chamber is of the same diameter as the classifying column, and has a conical bottom; it is provided with two openings, one in the cylindrical portion through which water is admitted, and the other, a small drain hole, in the apex of the conical bottom. The two compartments are bolted together and communicate with each other through the medium of a constriction plate provided with 3/16-inch holes spaced 1/2 inch apart. Constriction plates having any other percentage of opening may be substituted as the needs demand water is admitted to the compartment below the constriction plate at constant pressure. The volume of eater admitted is controlled with a valve. It should be mentioned that the classifying column at the bottom, just above the constriction plate, is glass.

Jan 1, 1929