Search Documents

By H. J. Hager, B. W. Gandrud, G. D. Coe

"INTRODUCTION The reduction of washery losses of marketable coal is a phase of coal preparation important to many of the Alabama coal producers. The problem has wide scope, and this report deals with but one of its several aspects. The investigation on which this report is based was made by the Southern Experiment Station of the Bureau of Mines with the cooperation of the Alabama By-products Corporation and the University of Alabama. The Alabama Byproducts Corporation provided samples of table middlings from its Colta washery on the Mary Lee bed at Flat Creek, Ala.PRACTICE AT THE COLTA WASHYAt Colta run-of-mine coal is crushed in a hammer mill in closed circuit with 5/16-inch square-mesh vibrating screens and tabled without classification on eight rectangular-deck wet tables. The coal is more friable than the bone normally present, and hence the bone is concentrated in the coarser sizes. An unclassified feed of this character can not be tabled with high efficiency to low ash content because of the sizing action of a concentrating table, which is such that when the tables are adjusted to exclude the coarse bone from the washed coal, a large amount of fine coal is lost in the middlings. At the time this investigation was undertaken there was no market outlet for middlings, with the result that middling products had to be discarded with the refuse."

May 1, 1939

By A. C. Johnson

This report is one of a series being prepared by the Bureau of Mines on exploration, development, mining methods, and costs at various mines in the United States. It describes operations at the Black Rock mine, Wah Chang Mining Corp., Mono County, Calif. The purpose of these reports is to promote development and conservation of our mineral resources by disseminating technologic information on mining methods, practices, and costs. The Black Rock tungsten mine of the Wah Chang Mining Corp. is 33 miles north of Bishop, Calif., in the Benton Range, Mono County, Calif. The property was acquired in August 1950 and a well-planned program of exploration, development, and exploitation resulted in a good production record with low costs. Operations were halted in July 1957, about 6 months after suspension of the tungsten purchase program by the Federal Government.

Jan 1, 1960

By Thomas O. Llewellyn

This U.S. Bureau of Mines (USBM) report presents a concise review on sources, processes, supply, and historical use patterns of domestic cadmium. It also covers a preliminary estimated cadmium material flow for the year 1989. This preliminary study contains information on cadmium and cadmium-bearing products in the United States. The data in this report were obtained from both published and/or unpublished sources of information. However, in order to estimate the fate of cadmium in each operation or application stage, some assumptions, judgments, and correlations were made by the USBM in an attempt to determine the material flows losses.

Jan 1, 1994

By Stephen C. Tadolini

The Bureau of Mines conducted field investigations in two underground mines to determine the actual loads to which bearing plates were subjected when installed in conjunction with full-column resin-grouted bolts and the roof movements generated by the applied loads. Measured loads indicate that the bearing plate is an integral part of the support system. Vertical displacement gauges installed to monitor roof displacements in the test sites show that the highest degrees of loading occur in conjunction with the largest amounts of movement.

Jan 1, 1986

By N. S. Dalal, X. Shi

"Electron spin resonance (ESR) measurements on solutions and isolated powders provide direct evidence for the involvement of Cr(V) species in the reduction of Cr(VI) by NAD(P)H. ESR analysis of an isolated Cr(V)NAD( P)H solid yields 6 11 = 1.9831 and 6.i. = 1.9772, indicating that the unpaired electron occupies the d22 orbital of the Cr(V) ion, with square-pyramidal geometry. Addition of hydrogen peroxide (H2 0 2 ) to the N AD(P)HCr( VI) reaction mixtures suppresses the Cr(V) species and generates hydroxyl (""OH) radicals. The ""OH radicals were detected via ESR spin trapping, employing 5,5-dimethyl-1-pyrroline-N-oxide and a-(4-pyridyl-1- oxide)-N-tert-butylnitrone as spin traps. The dependence of Cr(V) and ""OH radical formation on the H20 2 and Cr(VI) concentrations indicates that the Cr(V) species react with H20 2 to generate the ""OH radicals. Similar results were obtained by using various diols (arabinose, cellobiose, FAD, fructose, glyceraldehyde, ribose, and tartaric acid), a-hydroxycarboxylic acids, and glutathione. Investigations with superoxide dismutase showed no significant participation of 02 in the generation of OH radicals. These results thus indicate that the Cr(V) complexes, produced in the reduction of Cr(VI) by cellular reductants, react with H20 2 to generate ""OH radicals, which might be the initiators of the primary events in the Cr(VI) cytotoxicity.In this paper we report an electron spin resonance (ESR)3 spectroscopic detection of Cr(V) species in the reduction of potassium dichromate, henceforth called Cr(VI), by NAD(P)H and other diols. Also reported here is the detection of the hydroxyl (""OH) radical in the reaction between hydrogen peroxide (H2O 2) and a variety of Cr(V) complexes. This work was undertaken because while the reduction of Cr(VI) to lower oxidation states has been suggested as a key step m the mechanism of Cr(VI) toxicity, mutagenicity, and DNA alteration, the details are not yet clear (1-5).Earlier studies on the mechanism of Cr(VI) reduction in cellular systems include those on the reduction of chromate by microsomes (6-8), rat liver DT-diaphorase (9), and aldehyde oxidase (10). All these studies imply that Cr(VI) can be reduced to Cr(Ill) by cellular constituents. Regarding the mechanism of Cr(Vl) carcinogenicity, Jennette postulated that Cr(V) is the ultimate carcinogenic form of chromium compounds (8). This conclusion has led to many further investigations of the formation of Cr(V) in the reduction of Cr(VI) under biologically relevant conditions (11-33). More recently, however, Kawanishi and co-workers (34) have investigated the mechanism of DNA cleavage induced by Cr(VI) in the presence of H20 2 and have argued that it is not Cr(V) itself that is carcinogenic, but it is the reactive oxygenated species (02, 10 2 , ""OH) (produced by the decomposition of the Crv(02) ¾ - ion) that cause the DNA alteration."

Jan 1, 1990

By Lewis M. McNay

Description of methods employed and cost data are given for surface-mined land reclamation in Moraine State Park, Butler County, Pa. This project was conducted under the authority of the Appalachian Regional Development Act; a total of 177 acres of land was rehabilitated for specific land use purposes. The use of large equipment expedited the project work, and similar results could be anticipated on similar reclamation programs.

Jan 1, 1970

By McHenry Mosier

This paper is one of a series recently undertaken by the Mining Branch of the Bureau of Mines to describe current practice in diamond drilling for production at various mines throughout the United States and to discuss the relative merits of this method compared with drilling by percussion rock drills . The Bureau of Mines and the mining companies that are cooperating with it in this ' investigation have the objective of developing information on diamond -drilling blast holes for the benefit of all who are interested in the possible improvement of mining operations .

May 1, 1947

Toward the goal of maximizing minerals and metals recovery from domestic resources, the Bureau of Mines, U.S. Department of the Interior, has conducted in situ corrosion studies at the Salton Sea Known Geothermal Resources Area (KGRA) in the Imperial Valley, Calif., to evaluate and characterize materials of construction for geothermal resources recovery plants. General-, pitting, and crevice-corrosion characteristics of 13 commercially available alloys were investigated for periods of 15 and 30 days in seven process environments expected to be found in typical geothermal resources plants. Stainless steel alloy 29.4, Inconel 625, and the Hastelloys G, S, and C-276 were the most resistant to general corrosion, did not pit, and exhibited little susceptibility to crevice corrosion. Stainless steel alloys 430, E-Brite 26-1, and 6X had low general corrosion rates, but pitted and were susceptible to crevice corrosion. Stainless steel alloy 316 L had a low corrosion rate, but corroded intergranularly, pitted, and was susceptible to crevice corrosion and to stress-corrosion cracking. Titanium-1.5 nickel and TiCode-12 had low corrosion rates, did not pit, and were not susceptible to crevice corrosion. Carbon and 4130 steels had high corrosion rates, pitted, and had high susceptibilities to crevice corrosion. The major scale-forming mineral on the corrosion samples in most of the process environments studied was galena mixed with lesser amounts of other minerals.

Jan 1, 1979

By Louis C. Brichta

The Capital Mine is one of, the more important zinc mines in Lawrence County, Mo. Owing to the urgent need for additional zinc during the war and the available facilities for the treatment of zinc-lead ores at the property, the Bureau of Mines examined the mine during July and August 1942 and selected it for further investigation by churn drilling, which was accomplished in the fall of 1943 and spring of 1944. At the conclusion of the drilling on the Capital holdings, the Greenland property, immediately south, was investigated by drilling two additional holes. Results of the investigation are presented in this report.

Jan 1, 1948

From time to time the Bureau of Mines has interpreted and applied certain provisions of the Federal Coal Mine Safety Act and Federal Mine Safety Codes, primarily for the guidance of Federal Coal Mine Inspectors. Although interpretations of the Act have appeared in the Federal Register, the Code interpretations and practical applications have not been published. In response to many requests from representatives of the coal-mining industry, the Bureau is publishing this information to promote better understanding of those provisions that may be misinterpreted or misapplied. INTERPRETATIONS AND APPLICATIONS Two Federal Mine Safety Codes are discussed in this report, namely the Federal Mine Safety Code for Bituminous-Coal and Lignite Mines of the United States, Part 1, and the Federal Mine Safety Code, Anthracite Mines of the United States, Part 1. In this circular the word Codes refers to both directives; Code* refers to the code for bituminous-coal and lignite mines; Code? refers to the one for anthracite mines. Act* refers only to bituminous-coal and lignite mines.

Jan 1, 1963

By A. R. Taylor Jr.

The heat capacities of a-quartz form beryllium fluoride were measured at approximately 3° intervals from 8° to 300° K., using an adiabatic calorimeter. At 298.15° K the heat capacity and entropy were 12.39 cal/deg mole and 12.75 ±0.04 eu respectively. Enthalpy measurements were made with an ice calorimeter at approximately 30° intervals on the quartz and glassy forms of beryllium fluoride between 300° and 1,200° K. A melting point of 825° K and an 0,-8 type transition at 500° K with a heat effect of 75 ca1/mole were deter-mined from the enthalpy data for the quartz-type sample. Beryllium fluoride glass crystallized spontaneously into the quartz modification at 500° K. The heat of the reaction BeF2 (a-quartz) .... BeF2 (glass) was found to be 1,125 ±16 cal/mole at 298° K by solution calorimetry. This value, when corrected to 273° K, was used to correct for the heat absorbed by the formation of glassy BeF2 when the sample was dropped into the ice calorimeter from temperatures above the melting point. Using corrected enthalpy measurements, the heat of fusion was determined to be 1.13 kcal/mole at 825° K.

Jan 1, 1965

By J. T. McCartney

The Bureau of Mines has developed an automated reflectance scanning microscope system, primarily for determination of volume proportions, size distribution, and mode of association of the physical (petrographic) components of coals. The process, which is potentially more rapid and objective and less tedious than a visual microscopic procedure, involves magnetic tape recording of several millions of reflectance readings on micro-meter sized areas of polished coal surface and computer analysis and interpretation of some characteristics of the coal components. The system was tested in a study of pyrite distribution in steam coals. The application was essentially successful, but defects in polished pyrite surface characteristics and problems in adequate sampling prevented completely satisfactory results. Pyrite con-tent and coal-pyrite particle association could be determined nearly as well as by visual microscopy, but size distribution data were less acceptable.

Jan 1, 1969

By Francis Church Linxoln

"This property was explored as part of a general investigation of zinc-prodccing areas of southwestern Wisconsin at a time when an effort was being made to increase the production metals important to the Nation's war program. This report describes the work that was done and presents the data obtained.ACKNOWLEDGEMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the and that they make the greatest possible contribution to national security and economy. It is the policy of the bureau to publish the facts developed by each exploratory protect as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, P., G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director. Special acknowledgment is due Professor G. H. Pett, of the Wisconsin Institute of Technology at Platteville, Wis., Jack Tracy, manager of the Mifflin Mining Co., and J. M VanMatre, representative of the Defense Property, for their assistance in the work. Acknowledgment is also due to A. F. Agnew and A. V. Heyl, geologists of the Federal Geological Survey, for furnishing geologic interpretations and lithologic studies of the drill-hole sections. All drilling was done under the immediate supervision of Francis C. Lincoln and M. Howard Berliner, project engineers, Edward P. Barrett, district engineer, Minneapolis, and E. D. Gardner, regional engineer, of the Bureau of Mines."

Sep 1, 1946

By David K. Ingram

Research performed by the U.S. insurance industry has determined that mine subsidence is uninsurable. Consequently, the insurance industry has decided not to voluntarily offer mine subsidence insurance. The U.S. Department of the Interior has long been investigating the effects of mine subsidence. These investigations have resulted in Federal regulations and controls of mine subsidence. This U.S. Bureau of Mines report generally describes mine subsidence, the development of mine subsidence insurance programs, and the eight current mine subsidence insurance programs in the United States. The States that have these subsidence programs include Colorado, Illinois, Indiana, Kentucky, Ohio, Pennsylvania, West Virginia, and Wyoming. Major aspects of the programs include history, administrative and operational procedures, insurable structures, recognition of mine subsidence, major exclusions, claims, insurance premiums, and the economic health of each program. Addresses of agencies involved with mine subsidence insurance are also given. Information within this report can be useful for residential and commercial property owners and mine operators. States that are considering starting or have an existing mine subsidence insurance program can also use this report as a model for initiating or modifying their programs.

Jan 1, 1993

By R. R. Hornor, Geo. M. Hunt

The purpose of this paper is to point out some of the benefits and economies to be derived by the better selection , preparation, storage , preservation and utilization of mine timber , and to give some specific information on certain wood preservatives and processes suitable for mine timber preservation . The paper is based largely upon data obtained by actual experimentation and service tests conducted by the U. S. Forest Products Laboratory , Madison, Wisconsin, on wood preservation , covering a period of many years , and upon a field survey during the past summer by one of the mining engineers of the U. S. Bureau of Mines of some of the principal mining districts of Michigan , South Dakota , Montana , and Idaho , in which he made a general ' study of mine timber in metal mines , particular attention "being given to timber decay ; the conditions under which it takes place most actively ; the measures , if any , that are being used to combat it; and, finally, the advantages that might be anticipated in the use of chemically treated timber to prevent decay and thus prolong its life .

Feb 1, 1922

Control shearer-generated airborne respirable dust on longwall mining sections. Approach Previous Bureau studies have shown that using high-pressure water can have a significant impact on the amount of airborne dust released into the face airflow while cleaning and controlling the airflow in the immediate cutting zone. The basic concept to improve the drum water spray system was to utilize high-pressure (1,200 psi) inward-facing drum sprays to improve the dust knockdown efficiency of the spray system and confine the dust to the face area. This system would minimize the exposure of the shearer operator through dust avoidance and decrease face dust levels by suppressing the amount of respirable dust that becomes airborne. System Design In-mine tests were designed to provide information that would permit evaluation of the operation with different spray orientations and water spray pressures. This was achieved by comparison with a conventional baseline wet-cutting system consisting of 26 low-pressure bit sprays, located on the hit blocks to provide pick-point flushing. Total drum water flow was 60 gpm and was maintained continuously throughout all tests. The high-pressure inward-facing drum water spray system consisted of sprays located in each bit block, oriented 15° and 30° toward the face. The inward-facing water spray system was operated at either 800 or 1,200 psi.

Jan 1, 1989

By Robert J. Timkp, James D. Noll, Peter Hall, Robert Haney, Linda McWilliams

Diesel particulate matter (D PM) samples from underground metal/nonmetal mines are collected on quartz fiber filters and measured for carbon content using National Institute for Occupational Safety and Health Method 5040. If size-selective samplers are not used to collect D PM in the presence of car-bonaceous ore dust, both the ore dust and D PM will collect on the quartz filters, causing the carbon attributed to D PM to be artificially high. Because the D PM particle size is much smaller than that of mechanically generated mine dust aerosols, it can be separated from the larger mine dust aerosol by a single-stageimpacto1: The SKC D PM cassette is a single-stage impactor designed to collect only D PM aerosols in the presence of carbonaceous mine ore aerosols, which are commonly found in underground nonmetal mines. Howeve1: there is limited data on how efficiently the SKC D PM cassette can collect D PM in the presence of ore dust. In this study we investigated the ability of the SKC D PM cassette to collect D PM while segregating ore dust from the sample. We found that the SKC D PM cassette accurately collected D PM. In the presence of carbon-based ore aerosols having an average concentration of 8 mg/m3, no ore dust was detected on SKC D PM cassette filters. We did discover a problem: the surface areas of the D PM deposition SKC D PM cassettes, manufactured prior to August 2002were inconsistent. To correct this problem, SKC modified the cassette. The new cassette produced, with 99% confidence, a range of D PM deposit areas between 8.05 and 8.28 cm2, a difference of less than 3%.

By Frank E. Cash

The data in this circular were compiled so that individual phosphate companies might have the benefit of the experience of other phosphate companies, and that industries in general might compare experiences (taking into consideration relative hazards), thereby promoting accident preven¬tion. ACKNOWLEDGMENTS The descriptive matter is taken in part from a. paper by Cash and von Bernewitz.4/ Production figures ore from Mineral Resources of the United States;5/ accident data were furnished by each of the operating companies in the pebble-phosphate district, and their assistance in making this report possible is gratefully acknowledged.

Jan 1, 1936

By D. A. Reynolds, C. R. Holmes

The Bureau of Mines - American Gas Association ( EM - AGA) carbonization test has been used to determine the carbonizing properties of 66 American coals and a larger number of coal blends . A summary of the results obtained for the first 30 coals , including 6 blends , has been published ,4/ and results for individual coals have been reported as the investigations were completed . A bibliography of all publications pertaining to this work has been issued recently . Many of the coals were carbonized at 800 ° and 900° C. in two sizes of retorts ( 13- and 18 - inch diameters ) ; and , because the quality of coke is affected by changing the size of the retort , this report has been prepared to show the average physical properties of coke from the two sizes . This report also purposes to extend the correlation of the physical properties of coke with the rank of coal made by Fieldner and Davis in their summary of the EM-AGA tests on the first 30 coals .

Jun 1, 1942

By M. R. Geer

American and European practices in cleaning fine coal are strikingly different. The tables, launders, classifiers, and pneumatic devices used in America are seldom employed in Continental Europe, where much of the fine coal is cleaned in feldspar jigs, often supplemented by froth flotation of the extreme fines. This difference in choice of cleaning equipment may be fortuitous, but in large measure can be attributed to a difference in economic factors. Coal being more costly in Europe, there is greater emphasis on efficient cleaning of all sizes, including the extreme fines, and it is common to produce a high-ash middling for "on-site" consumption to avoid any waste of fuel value. The feldspar jig has been found advantageous under these conditions. In the United States fuel coal must be prepared as cheaply as possible, and metallurgical coal must be prepared as efficiently as possible; thus in both branches of preparation practice, any cleaning device that promises greater economy or higher efficiency warrants consideration. The feldspar jig, as employed in Europe, has a much higher unit capacity than the wet table used so extensively here and therefore offers economy in the capital costs of a washery through saving in space. As pointed out by Vissac,4/ the jig operates under automatic control, and therefore can cope with fluctuations in quality of feed. Maintenance costs for a single, large-capacity unit, such as the feldspar jig, would be expected to be lower than those for a battery of low-capacity cleaners. These considerations led the Bureau of Mines to undertake an investigation of the feldspar jig to determine its possible usefulness in this country.

Jan 1, 1958