Search Documents

By L. Weitkämper

The big challenge at present and in the future is the economization of resources. This is applied for the whole industry but particularly in fields of mineral processing. The most important resources are energy and water. The shortage and price advance of energy is worldwide noticeable whereas the shortage of water is regionally limited at present. However due to the increasing world population, associated with a rising standard of living, water will become more and more important. Studies of the Unesco from 2001 indicate that the total water consumption raised seven times since the last 100 years at a growth of population of just three times. (UNESCO-Currier, 10/2001). This trend is going to be increased. While today more than 90 % of the humanity has access to clean water, in 2050 just about 50 % will be in the same situation. These figures indicate the importance of a gentle handling with the resource water. Further more the disposal of fine products, containing most of the water, is an environmental concern and in the future the mining and processing of raw materials will become important and necessary in desert, arid or permafrost areas. In these areas just efficient dry cleaning technologies will allow an economical beneficiation or better enable the processing at all. Most of the separation technologies with high throughput rates in mineral processing are based on wet processes. This applies especially for the separation of fines. Though there are some dry technologies available for the separation of coarse materials, like pneumatic gravity separation [air jigs and air tables], magnetic separation and not least sensor based sorters. Dry separation of fines is bounded mostly on cost intensive and low throughput technologies. The pneumatic separation undergoes at present a renaissance, mainly due to the development of the all air jig by the German supplier Allmineral. This newly developed sorting device yields good results in the separation of coarse to medium size material. All these facts and figures show the potential and motivation for developing an efficient dry separation device for fines. The following article delineates the development, performance and chance of a new dry separation technology for fines.

Jan 1, 2014

By Hermann Wotruba, Lars Weitkämper

"Dry coal dressing was popular during the 1950.s and 60.s in many parts of the world. The devices mainly used were air jigs and air tables.The increase in ash and moisture content of run-of-mine coals due to the wide advanced mechanisation of mining mechanisation during and after this period led to that pneumatic devices being unable to treat run-of-mine coals with the desired efficiency. Since the 1960.s almost all new coal preparation plants have been based on wet processes that are highly efficient in terms of coal recovery and their ability to handle damp and sticky run-of-mine coals. (Frankland, 1995)However, water is becoming increasingly costly and the disposal of fine products, containing most of the water, is an environmental concern. There would be significant cost savings and a lower total energy consumption if coal could be cleaned dry. Efficient dry coal treatment would be an interesting solution in desert, arid or cold areas.In Germany one dry coal dressing plant is in operation. The process and the advantages and disadvantages are presented below.Further on new developments in the field of dry density separation of coal are reviewed and analysed. Test results of new dry coal separation methods e.g. new developed air jig and magnetic separator are reported."

Jan 1, 2003

By R. ?. Shishmarjov, Yu. ?. Davidenko, S. V. Bukhalov, ?. S. Baksheev, M. S. Shkirya, N. ?. Aikasheva, D. V. Bogdanovich, ?. Yu. Faustova

"The goal of prospecting operations in the Republic of Altay was to locate gold-sulfide-quartz mineralization. For this purpose we applied the technology of electromagnetic sounding and induced polarization (EMS-IP). These operations resulted in localizing promising sites with presence of sulfidization. The EMS-IP method proved to be highly efficient amongst other prospecting methods targeted at recognizing zones of sulfide mineralization making up 91%, considering that in more than half cases the ore intervals were the case. In the Yakutian diamondiferous province the EMS-IP technology was approbated during three field seasons to accomplish the assignments on searching for kimberlite bodies under conditions of various geological types. As a result, the reference objects were distinguished, and geoelectric parameters of kimberlite pipes of explosion were defined.INTRODUCTION In the time span 2015-2016 in Gorny Altay the EMS-IP technology was approbated in the Novokuznetsk area. The on-land areal geophysical survey was performed by EMS-IP method applied to identify, outline and locate promising sites with Au-Ag-bearing polymetallic mineralization within surveyed areas. Compared to the hosting rocks, the sulfides contained in polymetallic mineralization are typified by low specific electrical resistivity (SER) and high polarization. The areal survey conducted via EMS-IP method provided spatial characteristics of searched object. From July 2016 to August 2017 our expedition group carried out serial test works and laboratory investigations intending to define performance capabilities of EMS-IP technology in searching for kimberlite bodies under conditions of diverse geological types. The prerequisites for serial work were operations accomplished at the «Listvenichny» site lying 35 km away from Mirny town in the Sakha Republic (Yakutia), where the EMS-IP technology was probed for locating position and measuring geoelectric parameters of tuff pipe «Buardakhsky». After successful completion of operations it was decided to evaluate geoelectric parameters of kimberlite pipes of explosion."

Jan 1, 2018

By G. Bonifazi

Mining activities belong to human history, they are lost in the mists of time. They usually impact on large portions of the territory, both directly (exploitation areas and logistic activities directly related to exploitation) and indirectly (exploited material handling, processing and storage areas). As a result, at the end of mine life cycle, dismissed areas usually cannot be directly re-utilized without efficient and well addressed rehabilitation actions. Main goal of the proposed approach was to analyze the results obtained when a set of procedures, based on the collection and the analysis of remote sensed data, is developed to evaluate the effect of rehabilitation of land contaminated by extractive industry activities and to perform a monitoring and registration of the environmental impact of such operations by the application and the integration of modern information technologies, as Earth Observation (EO) and Geographic Information Systems (GIS). The study was developed in the framework of the EU-Asia program of the European union (EXTRACT-IT Project-Contract No: CN/ASIA IT&C/006 (89870): Application of Information Technologies for the sustainable management of Extractive industry activities) and it was addressed to three different dismissed mine areas in India, Thailand and China, respectively. The results, in terms of methodologies selected, strategies applied and results obtained, are described with particular reference to Fuxin coal mine area in China.

Jan 1, 2014

By Z. He

Based on full investigation of the characteristic of sphalerite in the residue obtained from cyanidation leaching process and the study of the mechanism of the interaction between flotation reagents and sphalerite with the aid of electrochemical analysis, the reagent named YO was developed for eliminating the depression effect of CN- on sphalerite and reducing the dosage of CuSO4. The achievements have been used in commercial production for the treatment of the cyanidation residue to recover the zinc minerals, obtaining a zinc concentrate with grade of 56.49% Zn and recovery of 86.63% Zn.

Jan 1, 2014

By Peter Ay, Vincenz Mehlstaubl, Satyanarayana Narra

"This study gives an insight into non-destructive testing methods suitable for porosity analysis at a small scale, firstly summarizing relevant state-of-the-art technology and pending patents, secondly realizing and documenting the start-up of the VHX-2000 digital microscope by the manufacturer Keyence and thirdly demonstrating practical application with the extended analysis of three fundamentally different agglomerates for which important application-related parameters are determined. Various analysis procedures on the different agglomerates the efficient and timesaving operational features of the digital microscope are outlined. Firstly an analysis of flax fibre agglomerates determines the process conditions best suited to produce agglomerates with specific properties by determining sphericity, cubicity, density and porosity as well as fibre damage and alteration. Secondly the production of iron-hydroxide - hemp-fibre agglomerates serves to obtain information on porosity values as a result of a cauterization of the fibres. The third analysis provides estimations of porosity values for acid-treated lignin agglomerates. Measurements were carried out with compact dry agglomerates and with soaked, expanded agglomerates, determining factors for total water carrying capacity. Practicability of non-destructive testing by digital microscopy is demonstrated and explained concerning the applications in this study by obtaining definite structural findings about the analysed agglomerates. Information on its operation is made available by a practice-oriented manual for the VHX-2000 digital microscope. Further suggestions for more in-detail analysis results with different instruments are given."

Jan 1, 2014

By J. H. Zhang

An atomic force microscope has been used to measure the forces acting between two silica and two rutile surfaces in the presence and absence of cationic surfactants, CnTACl (n = 12~18). The forces measured in the absence of surfactant can be fitted to the DLVO theory. At short separations, however, the silica surfaces exhibited repulsive hydration forces, while the rutile surfaces did not. On the other hand, the forces measured in the presence of the cationic surfactants show long-range attractions that are larger than the van der Waals forces. The long range attractions are the strongest at of the point of charge neutralization (p.c.n.), which decreases with increasing surfactant chain length. The possible origin of the long-range attraction has been tested in view of the charged-patch model of Miklavic et al. (1994). However, the sizes of the patches back-calculated from the model were much larger than those the patches (or hemi-micelles) determined experimentally and reported in the literature. It is, therefore, suggested that the long-range attractions observed in the present work are due to the structural response of the water molecules in the vicinity of hydrophobic surfaces.

Jan 1, 2014

By Stefaan J. R. Simons, Michael T. Spyridopoulos

In this paper the effect of humic substances (natural surfactants), electrolytes and solid particles on bubble coalescence, and as a consequence on froth stability, has been investigated. We formed two bubbles of equal size and forced them to collide using a novel experimental apparatus. The interactions were recorded by a high-speed camera, the images of which helped to determine the coalescence frequency and the coalescence time, as well as the mechanisms of the interactions. Two types of humic substances were used, along with three different electrolytes. Humic substances appeared to have a considerable effect on bubble coalescence, while the effect of electrolytes was minimal. Moderate and high hydrophobic glass spheres were used between two bubbles. Very hydrophobic spheres promoted fast bubble coalescence, while moderate hydrophobic spheres had no effect. We present data of coalescence frequency and time, as well as images of the coalescence events.

Jan 1, 2003

By B. Vasanthakumar, H. Ravishankar, S. Subramanian, J. Braun

The flotation of sphalerite and galena in the presence of intra- and extra-cellular components isolated from Bacillus circulans before and after adaptation to the chosen minerals has been studied. Based on various biochemical treatments, the key biomolecule primarily responsible for the flotation of sphalerite has been identified as DNA, which functions as a bio-collector. A noteworthy finding is the considerably higher flotation recovery of sphalerite obtained in the presence of single stranded DNA (79.8%) vis-à-vis double stranded DNA (50.2%). Selective flotation tests using the soluble fraction obtained after thermolysis treatment highlight that sphalerite-adapted cells yield a higher selectivity index (S. I.) of 31.2 compared to galena-adapted (S.I. 4.3) or unadapted (S.I. 12.2) cells. During bacterial adaptation to the above chosen minerals, the quantitative and qualitative changes in the surface potential, surface morphology and cell wall components have been monitored. The prior adaptation of the bacteria to sphalerite results in the secretion of a higher amount of proteins, eDNA and phosphate, whereas adaptation to galena leads to a higher amount of polysaccharide, uronic acid and acetylated sugar, vis-à-vis the unadapted bacteria. A significant observation is that the bacteria undergo a change in morphology from rod to sphere as a strategy to resist metal toxicity during adaptation to galena. Interestingly, this phenomenon is not observed during bacterial adaptation to sphalerite. This morphological transition has been shown to involve changes in crucial cell wall components as well as changes in the levels of expression of bacterial cytoskeleton element mreB gene involved in the maintenance of the rod shape. The sequence of B.circulans mreB gene has been identified using Polymerase Chain Reaction (PCR) followed by DNA sequencing.

Jan 1, 2014

In many base metal sulphide concentrators reagents such as collector and cyanide are often added to the grinding mill as well as to the flotation circuit. Whilst good reasons can be cited for splitting the reagent addition in this way, the benefits of such are rarely quantified and the complex reagent-mineral-media interactions occurring during milling are often poorly understood in terms of pulp chemistry. A new laboratory batch grinding mill designed by Magotteaux allows the user to measure, monitor, and control the pulp chemical conditions during grinding when testing different ores and media. Some of these parameters include pulp pH, pulp Eh, temperature, gaseous atmosphere, and dissolved oxygen concentration. In a recent development, the mill has been coupled with a simple on-line reagent monitoring system, designed by CSIRO, which allows the levels of species such as xanthate and cyanide in the grinding pulp to also be measured continuously during milling using a robust UV detection system. In this way the uptake of collector during grinding and the rate and ex-tent of cyanide interaction with the minerals and media can be determined as a function of grinding time. A series of grinding tests using an Australian nickel sulphide ore was conducted with the coupled system in which the cyanide dose, xanthate dose, and media type were systematically varied. The xanthate and cyanide levels were monitored as a function of grinding time and the data collected are discussed in terms of the pulp chemistry of the system and implications for plant reagent dosing strategies.

Jan 1, 2014

By A. Mainza, I. Govender, J. Waters

"The study of the properties of mineral processing suspensions is important in understanding how a circuit might behave. As soon as the predominantly dry ore enters a wet milling stage the ore properties undergo changes as a ‘slurry’ is created. Slurries can be classified in terms of their physical properties (particle density, solids concentration, particle size and size distribution, particle shape), and their flow properties such as rheology. Slurry flow regimes are classified into true homogeneous, pseudo homogeneous, heterogeneous and fully segregated, and only true homogeneous and pseudo homogeneous suspensions can be characterized by their flow structure. A class of the heterogeneous regime are the so-called dense phase or settling slurries - those which result in a clear water surface on standing, although they may approach a pseudo homogeneous state if suspended for a sufficient period of time. They are usually extremely difficult to characterize by their rheological properties alone and the rheological characterization of these slurries has always posed a problem, especially at higher concentrations. Previous rheological studies have focused on the individual concentrator units dealing with milling, classification, pumping, flotation, fine grinding, thickening.In this work an attempt was made to characterize two ore types (copper and a Platreef platinum ore) using a custom built Paterson and Cooke tube rheometer, at concentrations up to 43% by volume. After applying a turbulence correction, results showed Bingham plastic behavior. A conventional vane rheometer was then used to compare the rheological behavior of platinum concentrator streams. A size criteria was used to identify any rheologically dominant streams."

Jan 1, 2014

By Sumantra Bhattacharya

The per capita energy consumption in India is 510kgoe/year, the global average being nearly 1818kgoe/year. Correspondingly low is the per capita CO2 emission at 1.25t against the world average of 4.39t.65-70%, at times more, of India?s power generation from about 190,000 MW installed capacity, is however coal fired.India therefore has to secure diversified sources of energy and solar power is increasingly being looked as the real alternative to the existing over dependence on coal. To ensure sustainable solar power it is essential to secure its raw material base that is ?silica?, hitherto considered as ?minor minerals?. That calls for immediately addressing the issues of land availability, solar power cost, developing a dynamic inventory of silica containing minerals, appropriate processing technology and strong regulatory framework for sustainable mining and processing of all silica rich minerals. Keywords: silica, silicon, Thar, power generation, India, quartz, solar power

Sep 1, 2012

By G. Jenny

The particle size distribution of ground minerals is of decisive importance for downstream processes like floatation, separation, drying or others. In order to optimize the process efficiency on one hand and the final product quality on the other hand an early control of the grinding or classification stage is essential. The ultrasound based particle size analyser OPUS is capable of performing on-line particle size distribution (PSD) and solid content measurement of mineral slurries such as iron ore, copper ore, fluorspar, or quartz sand and alumina directly in heavy and rough process environment. The instrument provides a PSD of 31 size classes and can be applied for particles from nanometer range up to several millimetres. Arbitrary interpolations in between the 31 measured points are available. Typical residue values show an excellent agreement to off-line particle size analysis methods such as e.g. sieve analyses or laser diffraction. OPUS is designed as rugged in-line probe made from stainless steel. The applied technique is independent of product flow dynamics, contamination, optical properties, vibrations, pressures or changes in solid concentrations. The instrument provides all data on the system?s PC or on the process control system by a variety of interfaces.

Jan 1, 2014

By D. Endara, E. De la Torre, S. Echeverria

"The study was conducted with the sulfide mineral from the province of Zamora Chinchipe. It was characterized physical, chemical and mineralogical, obtaining between its main results a copper concentration of head ore of 0,58 %. The mineral was homogenized and taken to direct closed circuit: rollers mill - vibratory sieve (mesh # 16). Flotation was carried out in two stages: the collective and selective where in each one were performed 6 water recirculation as suggested by the technique used to relate information of a batch flotation to a continuous circuit called cyclic flotation tests (LCT). In the collective flotation (bulk) 2 Kg of mineral were grinded with 10 Kg of balls for 30 minutes and 62.5% of solids, the pulp was taken to the flotation process with solids percentages of 33.3% and pH 7, it was conditioned with 45 g / t of KAX 1%, 50 g/t of Aerofloat 208 and 20 g /t of Pine oil. The concentrate and tailings bulk obtained were filtered separately for the recovery of water and it was recirculated to the next grinding of 2kg mineral. In the selective flotation 1Kg of bulk concentrate was carried to regrind for 40 min, 62.5% percent of solids, 10 g of lime and 5 g of tannin FLOATAN T5, the pulp was taken to the roughing-collection-refining flotation circuit controlling the pH between 10.5 and 11 where conditioning (60 g/t of Aerofloat 208 and 30 g/t of Pine oil) and adding lime to the circuit and FLOATAN according to the procedure. The four fractions obtained from the circuit were filtered; the water was recirculated to the regrind process of the bulk concentrate. In the collective flotation process tends to stability in the fourth recirculating water to obtain a copper content of 4.5% and a recovery of 87%, recirculated water represents 69.8% of all water used in the 6 recycles. In the selective flotation circuit the fifth recirculating of water is the optimal where obtaining a copper content of 13% and a recovery of 72%, recirculated water in the selective flotation circuit represents 95% of the total water used in the 6 recycles."

Jan 1, 2018

By R. Kobialka

In the article results of experiments over jaws? linings in jaw crushers with different shaping of working surface were presented. Following sets of jaws were under investigation: immobile plain jaw and moving jaw with grooving surface. Grooving jaws have groves with circular, triangular and trapezoid cross section. In order to evaluate efficiency of comminution both the grain composition of product and the content of irregular grains were determined, as well as the size of crushing forces and process efficiency were measured. For the combination: plain jaw with grooved one, a good results were obtained as regards the grain composition of product and the content of irregular grains. Crushing forces were higher at crushing with mixed types of jaws (the one plain, the second grooved), in comparison to crushing with using both grooved jaws. Efficiency of the process was definitely higher for mixed jaws.

Jan 1, 2014

By M. Holuszko, I. Mikhalev

"Previous studies described by Galvin et al. (2017) have shown that for Australian bituminous coal fines, both in batch and in continuous process, the new improved oil agglomeration procedure based on the use of high-internal-phase (HIP) emulsions, as compared to the conventional “pure oil” agglomeration process, enables a significant reduction in the amount of oil while reaching a high yield of clean coal (approximately 90% of agglomerates greater than 355 µm in size) in a significantly shorter time. The HIP emulsion used in these experiments comprised up to 95% vol. aqueous solution of sodium chloride (3% wt. concentration) and for the rest, a mixture of kerosene (oil) and sorbitan monooleate (SMO emulsifier) in a 1:1 ratio as a binder. This study evaluates the applicability of the new HIP-oil agglomeration process to treat Canadian bituminous ultra-fine coal and Russian sub-bituminous coal fines and compares results from agglomeration to the flotation response of both coals. Oil agglomeration is known to be sensitive to surface properties of coal. Since surface properties of coals depend not only on the rank of coal but also on their origin (depositional environment) and mineralogical composition, both the applicability of this new improved agglomeration process to the non-Australian coals and its efficiency became the motivation for this study. To evaluate the applicability of the new process to both Canadian bituminous and Russian sub-bituminous coals, a series of bench-scale tests were carried out under conditions similar to those described by van Netten et al. (2016) for the Australian coals. Based on the results obtained in this research, new boundary conditions for the application of the HIP emulsion-based oil agglomeration process have been outlined and conclusions on the viability of the new process to treat ultra-fine coal from Western Canada and Russian sub-bituminous coal fines have been reached.INTRODUCTION In most cases, to meet the market requirements, the mined coal has to be processed to reduce the ash content by the removal of mineral matter and thus to increase the quality of the coal products (van Netten et al., 2016). Generally, flotation is used for processing fines from high rank coals; however, there are high losses of very fine coal due to the inefficiency of this process. Furthermore, difficulty in dewatering the fine coal results in excessive moisture levels causing coal handleability issues, which increases costs in the coal-cleaning industry (Capes & Darcovich, 1984). Much of the development that has occurred in fine coal cleaning has taken place with higher-value coal, often metallurgical (Klima et al., 2012). If the fine coal is deemed to be too difficult or expensive to process, it may be discarded as waste (van Netten et al, 2014). Such disposal not only creates an environmental liability but may also result in the loss of a valuable, high quality product that is better liberated than the coarser fractions of coal."

Jan 1, 2018

By Zhiyong Gao, Ruiying Fan

"Crushing and grinding are the prerequisite processes in many industries, such as minerals processing and powder technology. During crushing and grinding, minerals will cleave or fracture along the directions by broken the interlayer bonds (e.g., ionic bonds), generating some commonly exposed surfaces. The broken (or dangling) bonds at the generated surface makes the surface more active and determine the reactivity of the surface. In this work, the population of broken (or dangling) bonds on commonly exposed surfaces of fluorite mineral (a chosen model mineral) was calculated. Based on the calculated broken bonds information, the anisotropic surface reactivity of fluorite such as surface energy, surface relaxation, dissolution, wettability, surface charge and adsorbability, were discussed. The results show that the surface broken bonds density, which is positively related to the surface energy, can be used to predict the cleavage nature, surface relaxation degree and surface stability of fluorite crystal. The distribution characteristic and the number of broken (or unsaturated) bonds of surface active atoms (like Ca for fluorite crystal) can be used to predict and explain the anisotropic wettability, surface charge and adsorption mode and strength of organic molecules on different commonly exposed surfaces. It is easy to conclude that the calculation of surface broken bonds can serve as a fast and accurate way to start the mineral chemistry studies. These findings will be helpful to the mineral/material chemistry research in related interfacial science communities.INTRODUCTIONGrinding for mineral liberation is a prerequisite for a successful flotation separation. Also grinding for size reduction is a prior process for a favorable powder technology. During the grinding process, the minerals / materials will cleave and fracture along certain crystal directions with relatively weak interlayer chemical bonds1 to form a number of common exposed surfaces. Exposed surfaces are the outer boundary of a solid substance. In the mineral / material block, the bonding orbital of the atoms is filled with electrons and the atoms are in a steady state. Atoms on these exposed surfaces appear to show dangling bonds (or broken bonds) by losing chemical bonds to adjacent atoms in the previous block. Therefore, surface broken bonds serves as an initial property of a fresh surface. The lattice arrangement and crystal orientations causes differences in the number of dangling bonds on each exposed surface, i.e., anisotropic surface broken bonds2. The anisotropic dangling bonds enable the exposed surfaces to show varying degrees of surface reactivity (including surface energy, surface charge, surface relaxation, dissolution, wettability and adsorption behavior), known as anisotropic surface reactivity."

Jan 1, 2018

By W. Z. Yin

With increasing of mining depth, many iron ores in Liaoning Province contain carbonates such as siderite and ankerite. The emergence of these carbonates in ores creates a fatal impact on the running producing process of anionic reverse flotation in Dong Anshan Sintering Plant, which leads to ?concentrate and tailing no separated?. And its reason is still unknown. Moreover, siderite, despite that its ferric theoretic grade is only 48.2%, however, do not affect the blast furnace utilization factor, therefore, can be used as raw materials in ironmaking. In order to solve the separate problem of iron ore containing carbonates, five pure minerals, martite, magnetite, quartz, siderite and ankerite, were selected for a series single flotation experiment. The aim was to discover the flotation difference of these minerals, furthermore, to explore a new flow sheet for the iron ore containing carbonates. The results of single mineral flotation experiment reveal that the combination regulators, starch and CaCl2, in different pH extent, can make these minerals taking on obvious flotation difference, which make it possible to process the iron ore containing carbonates. A new flow sheet, step-flotation, to process iron ore containing carbonates is explored, that is, first step, direct-flotation processing, is to eliminate the bad effect that the carbonates bring in flotation system by collecting carbonates under neutral condition; the second step, reverse?flotation processing, is to get qualified iron concentrate by collecting quartz under alkaline condition. Manual mixed ore sample were processed successfully through this new flowsheet under proper reagent system, which has absolute advantage compared with routine flowsheet. Actual ore sample of compound magnetic separation concentrate were processed successfully both open and closed circuit experiment through this new flowsheet. SEM and EDS were used to probe the reason why carbonates affect the regular processing. It is analyzed that moderate floatability of siderite and its coating on the surface of hematite and quartz make the phenomenon ?concentrate and tailing no separated?. This research provides a reasonable processing scheme for iron ores containing carbonates and can be used for reference in processing other complicated, refractory iron ore.

Jan 1, 2014

By M. Barsky, E. Barsky

It is generally accepted that the optimal flow velocity for gravity classification is the final particle settling velocity or, which is the same, the particle spin velocity. However, we have found differences between the settling velocities and the spin velocities of the very same particles. Here we present the results of experiments in a cascading gravitational classifier comprising eleven stages. The feed material was introduced at each stage successively, from the first to the eleventh. The optimal flow velocity was determined for each case. From these experiments it follows that the value of the optimal flow velocity depends to a greater extent on the point of introduction of the feed (i.e., on the design of the device) than it does on the interaction between the solid phase and the flow.

Jan 1, 2003

By Arkady Senchenko, Yury Kulikov

"Basic theoretical grounds of the methods applied for crushing and grinding parameters determination according to international standards are given in this paper. Statistical data about crushability and grindability research are shown. The potential relationship between the values of Fred Bond Work indices and John Starkey indices (Crushing index, Ball mill index, Rod mill index and AG/SAG index) are discussed in this paper. In order to establish correlation between the crushability and grindability indices the analysis of over 2 500 tests for 165 deposits located in different parts of the world was performed. The relationships among different types of energy consumed for crushing and grinding were determined. A method for preliminary estimation of energy consumption in semiautogenous + ball mill grinding circuit is suggested for its application in preliminary technological solutions development and technical-and-economic assessment."

Jan 1, 2014