Search Documents

By Leon Lorenzen, Charlene Gokhale

"In excess of 24 x 106 tons (Eskom, 1997) of coal-derived fly ash is produced annually in South Africa for the production of electric power. A large quantity of this ash is disposed of as a solid waste in landfills, thus posing a serious environmental problem. Due to the shortage of landfill sites, new ways of utilising fly ash are needed. Recently several authors have shown that various combustion fly ashes can be converted into zeolites to obtain industrial products with applicability in environmental management. Geopolymerisation has emerged during the last few years as a possible solution to some waste stabilisation and solidification problems. henolic compounds have been shown to be toxic to soil microorganisms at the parts-per-million level. Indeed several of the organic compounds classified by the U.S. Environmental Protection Agency as priority pollutants, are phenols. Immobilisation of phenols by adsorption on zeolites and encapsulation in a geopolymer appears to be a promising solution to this problem.This paper reports a technique for the production of a low-silica sodium zeolitic material from fly ash (zeolite NaP1), and its application for the stabilisation of phenols by adsorption and subsequent encapsulation in a geopolymer matrix. A commercial zeolite, clinoptilolite was also utilised as an adsorbent. Due to their uniform pore sizes and large surface areas, zeolitic materials are suitable for ion exchange and adsorption of certain organic substances. Adsorption data show that the commercial zeolite, clinoptilolite was an effective adsorbent for organics. Adsorption data showed that between 51.2 ppm and 74.3 ppm of chlorophenol or between 15.4 ppm and 32.5 ppm of phenol could be adsorbed. Physical encapsulation of the coated zeolite loaded with organic within a geopolymeric matrix increased the compressive strength of the matrix from 28.80 kN to 40.79 kN. Leaching data for the various geopolymer matrices with encapsulated and loaded zeolites show no organics being leached from the system at a detection level of 2ppm. According to the SABS these would have been acceptable organic concentrations within a waste water stream."

Jan 1, 2003

By I. S. M. K. Ilankoon

In heap leaching the transport of the acid from the drippers to the surface of the ore particles is a major factor in the overall performance of a heap. This flow behavior is complex as the flow is unsaturated and occurs along a tortuous set of inter-particle channels and connections. Previous modeling of this system has used equations from oil and ground water flow to model these systems, but the applicability of these models with the larger particles found in typical heaps is suspect as these systems are not necessarily capillary dominated. In particular, as the characteristic particle size goes from below to above a few centimeters, the flow changes from capillary to gravity dominated. This means that typical heap leaching heaps cover this interesting, but complex, transitional fluid flow regime. In this paper a set of experimental studies of this flow, including PEPT (positron emission particle tracking) based tracer experiments, highly accurate liquid holdup measurements and axial dispersion experiments using salt tracers will be presented. In this study, flow through mono-dispersed particle beds was carried out. In particular, the hysteresis in the liquid holdup as the liquid flow rate into the particle bed is varied is investigated, since this hysteresis means that the relationship between flow rate and holdup is history dependent, an effect not included in models currently used to describe fluid flow in heaps. A theoretical model that describes this hysteresis will also be presented. Keywords: heap leaching, hydrometallurgy, modeling

Sep 1, 2012

By Xie Jiyuan, Hu Yuehua, Yang Songrong, Zhu Zhansheng, Qiu Guanzhou

"By the end of 2000, the first bio-oxidation plant in China that designed by ENFI come successfully into commercial operation in Yantai Gold Smeltery. Its capacity is 50t/d of refractory gold ore concentrate. After the extension, the capacity of bio-oxidation plant reached 80t/d of refractory gold ore concentrate at end of 2001.The refractory gold ore concentrate treated is from different gold mines. After proportionate feeding, the feed typically consists of Au (52.7g/t), S (24.42%), As (3.58%).The bacterial culture used in the bio-oxidation circuit is taken from a mine in south of China, and has been grown over 20 years on a variety of sulfide concentrates in a laboratory of mineral processing, and has shown to be adaptive to growth in a high concentrations of arsenic. It is a mixture of mesophilic microorganisms. The nutrients used in the bio-oxidation process are (NH4)2SO4, KH2PO4, KOH.Before feeding to bio-oxidation circuit, the concentrate would be milled to minus 43µm. The biooxidation product is fed to solid/liquid separation system that consists of a thickener and two press filters, solid from the system is fed to CCD circuit, liquid from the system is fed to neutralization area. The neutralized product is fed to another solid/liquid separation system, and the solid from the system is disposed of on a wasted quarry pit, the liquid from the system is returned to bio-oxidation circuit for reusing."

Jan 1, 2003

By G. Onal, E. Gock, H. Dincer

"During the conventional chromite dissolution process; chromite ore concentrates were ground to at least <90 µm using the ball mill and after adding Na2CO3 and leaning material (instead of CaCO3 also residues from the leaching process) at a ratio of e.g. 1:0.75:1.2, depending on the specific formulation, follows the digestion e.g. in a rotary kiln, heated in countercurrent. The reaction time is 3 to 8 h. The calcine is comminuted and leached with water or a thin chromate solution. Depending on the type of ore used, the yield is 75-85 %. The disadvantage of the above-described process is that it is impossible, using current technology, to achieve a complete digestion of the chromite ores and that the chromium-containing residues have to be disposed of as special waste, involving a large financial effort.The subject of this study was the investigation of the effect of vibratory milling on chromite dissolution. The impact stress in the vibratory mill causes the mechanical activation of chromite, which is characterised by lattice defects. The degree of mechanical activation can be quantified by measuring the relative X-ray diffraction intensities at the parent lattice planes of chromite. Each relative X-ray diffraction ratio correlates with a certain degree of digestion. As opposed to vibratory milling, a complete digestion of chromite using a ball mill is impossible, even at extremely long grinding times.In this investigation a chromite concentrate from Pulpinar/Kayseri with content of 44 % Cr2O3 and the Eccentric Vibratory Mill was used. In order to verify the effect of the vibrating grinding on chromite dissolution, reaction kinetic investigations on digestion and leaching were carried out."

Jan 1, 2003

By Elena L. Chanturiya, Vladimir A. Bocharov, Roman A. Amosov

"In many volcanogenic base metal deposits of Russia the gold is closely associated with copper sulphides and pyrite. The recovery of gold associated with pyrite is especially difficult problem.Investigations of gold chemical state and mineral forms in copper-zinc sulphide ores of Gay and Barsuchiy Log deposits in the Urals have been made using EPMA, optic image-analysis, XRA, SEM, thermo-electrical force measurements and selective gold leaching experiments.Two gold varieties are determined: 1) free native gold particles (from 5 µm up to 0,25-1,0 mm), which can be liberated after grinding of ore up to 0,074 µm and named “free gold”; 2)”invisible” gold, including finely disseminated native gold and chemically bound gold. The second variety can’t be disclosed during grinding. Free gold can be recovered by gravitation and flotation while the processing behaviour of “invisible” gold is determined by properties of gold-bearing sulphides: pyrite and chalcopyrite. According to results of diagnostic leaching experiments in ores of deposits mentioned above the part by weight of free gold reaches 70%, the part by weight of the ”invisible” gold is up to 20%. About 10% of gold is enclosed in quartz and acid-soluble minerals.Theoretically (taking into account gold distribution data) it’s may anticipate gold recovery by gravitation up to 60%. However after grinding up to 50-60% of class –0,074 mm only about 40% of gold passes into oversize product including 30% of free gold and 8% of ”invisible” one. It can be recovered by gravitation. Remaining free gold and ”invisible” gold can be extracted by flotation – 25% in total. Inevitable gold losses in tailings may reach 8-10%."

Jan 1, 2003

By R. L. Pascual, W. J. Whiten

"The froth flotation process is not well understood. Both flotation models, and the parameters used to describe the stream flows are not well defined. They in fact vary considerably in different applications. This creates difficulties is designing a simulation program suitable for use by plant personnel, consultants, and researchers. In addition to simulation, an effective simulation program can be expected to provide a range of other services.This paper shows how a process circuit simulator can be designed with sufficient flexibility to satisfy these needs, and discusses some of the additional services.OVERVIEWThe development of a simulation program for froth flotation circuits faces several challenges as flotation models and the associated stream descriptions are not well defined. There is little agreement on the best form for a flotation model, or on how the plant streams should be defined.In addition to simulation, a flotation simulator is generally expected to provide other services such as data input, data reconciliation, model fitting, and accuracy estimation. Additional services may also be needed beyond what might initially be envisaged. A summary of some of these possibilities is included.To apply simulation to a flotation circuit it is necessary to develop a flotation cell model, for instance based on the general outline given in the appendices. Experimental data, usually from the plant, is needed to determine cell model parameters. This is generally done by first undertaking data reconciliation to determine if mass flow constraints are sufficiently closely satisfied. At the same time the data is inspected for outliers that might bias subsequent calculations. Next the data is fitted to a model to back calculate ore characteristics. If there is sufficient agreement between the fitted model and the data, the model can then used to make predictions of the effect of changes to the plant. The changes, that the simulation shows are beneficial, can be applied to improve plant performance"

Jan 1, 2003

By P. Harris

"Comparison of the two most commonly used classes of depressant in the South African platinum industry is complicated by the fact that these polymers induce different effects on the surfaces onto which they adsorb. The use of carboxymethyl cellulose (CMC), which is ionically charged in solution, can lead to increased particle dispersion in addition to the effect of reduced surface hydrophobicity (depression). Guar is typically only slightly charged in solution. Comparison of these two depressants is complicated since it is uncertain whether differences in their action is a result of either depression of dispersion effects.This work investigates the role of dispersion independently to that of depression in the batch flotation of a platinum bearing ore. An inorganic dispersant, sodium hexametaphosphate (NaHMP) was added in parallel to the uncharged guar depressant to simulate the action of depressants with varying degrees of dispersion. By distinguishing between the material recovered by entrainment and the floatable gangue and by including the effects of froth stability it was possible to decouple the effects of dispersion and depression.The results show that both dispersion and depression led to increased grade of the sulphide minerals. Depression leads to a decreased recovery of floatable gangue minerals. Dispersion leads to an increased recovery rate of these minerals and an accompanying decrease in froth stability."

Jan 1, 2003

By Paul Gottlieb

This paper reviews the status of automated applied mineralogy today and describes the history and fundamental theoretical and practical bases underpinning the development of automated systems. Details are given of the technical challenges that were faced in creating the new technology and in applying it to a range of applications. In recent years, automated mineralogy has become established as an essential enabling technology for the reliable acquisition of statistically sound comprehensive mineralogical and metallurgical data. This has had a revolutionary effect on the industrial use of such data in the study of geology, mining and mineral processing. Previously, using manual methods, it was not feasible to attempt this work because the large data sets required could not be assembled in a realistic timescale. There was a reliance on individual expert mineralogists and this was not scalable. The speed, reliability, detail and repeatability of the modern automated measurements has now made this type of analysis routine. Automated Applied Mineralogy has come of age! More than 100 systems have been installed around the World. Automated mineralogical analysers such as QEMSCAN® were originally developed as diagnostic metallurgical tools to improve mineral processing plants using samples drawn from plant surveys, bench and pilot-scale tests. They were used mainly for the assessment and auditing of size fractions of mill products, such as concentrates and tails. Subsequently, they began to be used for concentrator design and optimisation where ore characterisation was used to help understand the relationship between the feed ore and its subsequent behaviour in the plant. They are now widely used to measure exploration cores and drill chips from drilling programs to predict eventual metallurgical performance. Ore samples can be classified into metallurgical, as well as geological types, by combining mineralogical features in the ores with metallurgical properties related to grade control, separation, comminution, flotation and leaching behaviour. Three-dimensional block models of ore deposits are now being created based on processing response in addition to geological and mining properties. The development of automated systems began in Australia, the United Kingdom and Canada in the late 1970s and early 1980s. There were many technical challenges. Mathematical theories of randomness, sampling theory, image analysis and stereology were developed to ensure sample representivity so that meaningful information could be obtained. Sample preparation, presentation and measurement methods were developed to ensure that the random sampling was preserved during the measurements. Methods of automatic measurement and mineral identification evolved from the use of electron microscopes, fitted with backscattered electron brightness and energy dispersive X-ray detectors. Operational procedures were required to ensure that these instruments could accommodate a large number of samples and operate unattended for long periods of time. The new technology was progressively applied to a range of commodities and applications and new analysis methods, such as liberation measurement, were needed for metallurgical interpretation of mineralogical data.

Jan 1, 2014

By Atsushi Shibayama, Toyohisa Fujita, Luo Lin, Toshio Miyazaki

A novel process is developed in this study for separation of tungsten and vanadium from a leach solution of tungsten alloy scraps. Specifically, a magnesium salt combined ammonium solution is employed to precipitate vanadium and impurities in the purification of the leach solution. This separates vanadium from tungsten by rejecting tungsten in aqueous solution. Finally, tungsten is recovered as the form of ammonium para-tungstate (APT). Vanadium is recovered as the form of ammonium meta-vanadate(AMV).

Jan 1, 2003

By Elzbieta Mielczarski, Jerzy A. Mielczarski

"It is well documented that xanthate adsorption on sulphide minerals is electrochemically controlled process. Under well controlled potential conditions the adsorption of xanthate takes place at different potential on each mineral, hence, each mineral component can be selectively separated from ore. This was demonstrated in the past for single mineral systems. In real flotation this concept never works out for two reasons: the potential of single mineral particle results from its interaction with solution as well as from galvanic contact with other particles present in the flotation pulp. Thus, the potential of a single particle results from complex surface reactions controlled by solution chemistry and the presence of other mineral particles that also interact with the solution. In flotation it is not possible to control mineral particle potential as it was demonstrated in voltametric studies of single mineral.In this study adsorption of xanthate on pyrite, galena and chalcopyrite has been investigated in the presence of those minerals. The second mineral was in solution: (i) without any physical contact with the first one, (ii) in direct contact (non-liberated grain or connected by wire), (iii) in collision type contact similar to that observed in real flotation.The adsorption of amyl xanthate on pyrite, galena and chalcopyrite was monitored by infrared external reflection technique directly on mineral surfaces. Type of the adsorbed species and their amount were concluded from the recorded reflection spectra. The presence of second mineral in solution without any physical contact does not influence adsorption. The minerals behave as if they were separated (at least during 30 min of the experiment). However, any type of galvanic contact between grains of two different minerals has tremendous consequence on the adsorption of collector on the both minerals. The detected changes are dramatic, from no adsorption to a few monolayer coverage formation.For example, pyrite that adsorbs amyl xanthate strongly in single mineral system in its galvanic contact with galena practically shows no adsorption of the collector in the same solution conditions. On contrary adsorption of xanthate on galena is tremendously enhanced during the galvanic contact with pyrite. The observed changes in the surface reactions are discussed and mechanisms of xanthate interactions in different galvanic contact are proposed."

Jan 1, 2003

By Ralph J. Holmes, Victor Sharp, Steven J. Spencer, CSIRO Minerals, Kevin J. Davey, Jonathan J. Campbell, Peter L. Phillips

"Improved measurement tools for monitoring and control of AG/SAG mill performance have a high level of interest in industry. Historically, acoustic emission monitoring has been widely used on SAG/AG/ball mills and hydrocyclones to provide new information on the conditions inside these devices affecting their performance. The current work was focused on a new technique using surface vibration monitoring of a number of pilot-scale and production-scale AG/SAG mills to yield insights into the events occurring in the mills. The development of relationships between signal analysis outputs and mill operating conditions can be used for soft-sensor measurement of mill process variables. The technique used an array of accelerometers mounted on the mill lifter bolts linked to a fast data acquisition system which monitored the surface waves generated during operation. Details of the system are presented. Mill operating variables were adjusted systematically to provide a wide range of operating conditions for surface vibration signal collection. The experimental approach is discussed.The signals acquired during the experiments were analysed using a range of techniques. The results show that strong relationships exist between measured vibration power (both total power and within certain frequency bands) and mill load level/power and mill speed. A new method for extraction of power spectral density and band power information on features of interest in a mill rotation cycle is also presented."

Jan 1, 2003

By Kang N. Zhong, Hui H. Luo, Yunan Phosphate Chemical Co., Yi H. Wei, Yao J. Li, Yu L. Wang

"The three kinds of phosphate ores (igneous, metasedimentary and sedimentary) found in China have great differences in flotation flowsheets and reagents suite because of their crystal structure and mineral composition. The igneous and metasedimentary apatites have good floatability with fatty acid as collector and waterglass, sodium hydroxide or sodium carbonate as conditioners. The sedimentary phosphate is very difficult to beneficiate by direct flotation because of their poor floatabilities and relatively high content of MgO and SiO2, even though the dolomite depressants are used sometimes.The differences in floatability of apatites in China are closely related to their differences in specific surface area. The amount of collector to float apatite increases with the specific surface area. Apatite with lower specific surface area showed good floatability at lower collector concentration. Apatite with a higher specific surface area needed a higher concentration of collector. The content of CO3 2- will affect the specific surface area of apatite by distortion of its crystal structure and consequently affect its floatability.Dolomite can be easily rejected from apatite in a weak acidic medium (pH=5), especially in phosphoric acid medium by reverse flotation. Quartz and siliceous gangue in sedimentary apatite can be removed by direct flotation using fatty acid or by reverse flotation using amine. Amine is not practically applied because sedimentary apatite in China is usually very fine and needs fine grinding, which always results in excessive, very fine, stable and non-flowable foam.Based on the floatability of phosphate ore in China, a two-stage flotation process, direct and reverse flotation (D+R), was developed to beneficiate sedimentary ore. For the Haikou phosphate ore containing 25.11% P2O5, 3.46% MgO and 16.5% SiO2, a concentrate containing 31.84% P2O5, 0.48% MgO and 14.8% SiO2 can be obtained through a continuous D+R test at a recovery of 89%."

Jan 1, 2003

By John C. Gathje, Rick Moritz, Wilhelm de Beer, Gary L. Simmons

"Froth flotation has a long history of success for the recovery and concentration of a wide variety of minerals of commercial interest. Both the art and science of flotation have progressed greatly, and as our knowledge has increased so has our ability to improve mineral separations and recoveries.One area of interest in recent years has been the flotation of refractory gold ores to recover the goldbearing sulfides. In many instances, the use of conventional air flotation to concentrate these values has achieved only limited success. However, as a result of intensive research, Newmont Mining has expanded the boundaries of flotation, and it can now be used to successfully treat many gold-bearing sulfide ores as well as platinum and palladium ores. This has been achieved through the use of the patented N2TEC technology, which utilizes nitrogen as an inert gas in the flotation process."

Jan 1, 2003

By Patrick A. Turner, Timothy J. Olson, Abraham J. Schutte, Roman van Ommen

"The use of classifying devices in grinding circuits dates back to the early 1900’s when classifiers were installed to close ball mills. The search for ways to further improve grinding circuits led to the use of hydrocyclones in place of mechanical classifiers in South Africa in the early 1950’s. Today Hydrocyclones are considered as the best classifying devices to close grinding circuits. After 50 years of development the hydrocyclone has changed significantly when compared to the designs of the early days, but the focus to circuit optimization must be expanded to an understanding of the integral system consisting of mill, cyclone feed pump and cyclone.The key to good cyclone circuit design and operation in primary grinding circuits will be discussed including individual cyclone design features such as cone angle or materials of construction, as well as orientation and manifold configuration.Cyclone performance issues as well as maintenance considerations will be detailed in an effort to achieve consistent cyclone operation with minimal coarse solids in the overflow. “The importance of constant cyclone feed conditions is unquestioned today. The challenge of Cyclone sizing is a large number of not fully known variables prior to startup. The most significant unknown variable is slurry viscosity. Because of this, engineers often specify a conservative cyclone system that produces a finer than required separation. However, this approach often leads to higher circulating loads and a higher overflow density in order to produce the required separation. The higher cyclone overflow density results in a less efficient cyclone separation. The average concentrator can pick up 2-4% finer overall grind by having a more aggressive cyclone operation.”"

Jan 1, 2003

By P. N. Mohan Das, K. Harikrishna Bhat

"The major ilmenite reserves are located in India at Chavara (CH), Manavalakurichi ( MK) and Chatrapur, Orissa (OR). India stands first in terms of ilmenite reserves, which are estimated to be 278 million tonnes out of which, 142 million tonnes are processable. Mineralo-chemical analysis showed that Chavara ilmenite is the most weathered one with about 60% TiO2 while Chatrapur is the least weathered with about 50% TiO2. XRD and SEM studies of different magnetic fractions of these three mineral deposits established the co-existence of ilmenite with pseudorutile, rutile and haematite phases in substantially varying amounts. It is observed that the tropical weathering rather than the source rock difference has apparently played an important role in imparting major compositional and structural dissimilarities among the ilmenites in different places. Further, the chemical analysis, XRD and SEM characterisation of differently weathered samples of MK ilmenite separated by the magnetic fractionation showed that the degree of alteration was invariably associated with the decrease in magnetism, increase in the rutile phase and the change in Fe2+/Fe3+ ratio of ilmenite grains. Magnetically separated fractions when subjected to metallisation with carbonaceous reductant such as coke showed that the degree of reduction increases with the degree of alteration and with the decrease in the Fe2+/Fe3+ ratio.In the processing of ilmenite through the Becher process, aeration rusting of pre - reduced ilmenite is found to be the rate-limiting step thus, affecting the productivity and economy of the process. Investigations have proved that the addition of some organic compounds such as glyoxal, sucrose etc., to the system accelerates the reaction to such an extent that the rusting time has been reduced to less than half. The formation of acids by the these organic compounds during the rusting reaction was proved responsible for maintaining the pH of the solution in the range 3-4 at which iron hydroxide do not precipitate and block the pores in the reacting surface of the grain."

Jan 1, 2003

By Carin Laubscher, Francis W. Petersen, Jaap P. Smit

"Waste streams, such as acid mine drainage, are often characterised by low pH values and high concentrations of heavy metals, dissolved solids, calcium and sulphates. Although lime remediation effectively removes most of the heavy metals as hydroxides, it is less effective at lowering levels of sulphates. Various methods of removing sulphates from effluents exist, such as precipitation with lime, precipitation with barium salts, co-precipitation with calcium carbonate, reverse osmosis, and ion exchange. Mintek developed a chemical precipitation (SAVMIN) process to treat acid mine drainage, which entails the addition of lime to precipitate the metal hydroxides, and the subsequent formation (precipitation) of calcium sulphoaluminate or ettringite. The key to the viability of the new technology lies in the correct use, regeneration and recycling of Al(OH)3 used to precipitate the ettringite. The water produced by this process is suitable for disposal to watercourses or for agricultural, domestic or industrial consumption. No brines are produced as the salts are converted to solid hydroxides, gypsum and calcium carbonate.The SAVMIN process has been tested successfully during several laboratory scale operations, and during two pilot plant operations at Stilfontein Goldmine for Anglogold and Navigation Plant, Witbank for Anglocoal. During the pilot plant campaign at Navigation Plant, metal and mineral precipitation was achieved with lime addition. The sulphate concentration in the water was reduced from 2136 mg/L to an average value of 102 mg/L and the calcium concentration was reduced from 727 mg/L to an average value of 70mg/L.The SAVMIN process generates a number of different waste streams including metal hydroxide sludge from neutralisation, gypsum sludge from the gypsum crystallisation steps, and calcite sludge from carbonation. The metal hydroxide sludge is composed of Mg, Ca, Mn and Fe hydroxide, and could be disposed of on a slimes dam. Gypsum sludge was greater than 99% CaSO4.2H2O. This gypsum could be used for dump or road capping, underground backfilling, production of wallboard and cement. The calcite sludge is pure CaCO3, which is recycled back to the neutralisation stage."

Jan 1, 2003

By Lev Filippov, Vyacheslav Severov, Inna Filippova

"Reverse cationic flotation is a very efficient method of beneficiation of oxidized iron ores when you need to separate hematite and quartz. This method can be also applied to reduce silica content in the magnetite concentrates obtained by wet low-intensity magnetic separation. However, cationic flotation in this case is less effective due to the presence of Fe-Mg-Al-bearing silicates as amphiboles in magnetite ores. These silicates are concentrated in magnetic products and determine the difficulties of their separation from iron oxides when amines and starches are used as collectors and depressants, respectively. The recalculation of the results of the electron microprobe analysis of three calcic Fe-Mg-Al-bearing amphiboles used to characterize cation distributions in structural units and to obtain structural formulas in accord with stoichiometric limits was conducted. The Mössbauer spectroscopy was used to examine the validity of the empirical estimation of cation distributions in amphiboles. The studied samples are metamorphic pargasite and ferrotschermakite and volcanic magnesiohornblende. The crystallographic analyses of the amphibole samples exhibited their heterogeneous surfaces explaining worse floatability of amphiboles with dodecylamine at pH 10. The electrokinetic measurements showed that the position of the isoelectric point of amphiboles is related to a substitution of Al3+ for Si4+ in tetrahedral sites and to an amount of Mg2+ cations in octahedral sites. Thus, the dodecylamine adsorption onto amphiboles through electrostatic interactions is mainly affected by a distribution of these cations in tetrahedral and octahedral sites of amphiboles. In addition, the effect of starch on the depression of Fe-Mg-Al-bearing amphiboles during flotation can be attributed to the presence of metal ions on the amphibole surface, which are capable of forming strong chemical complexes with starch molecules."

Jan 1, 2014

By M. Evertsson, M. Johansson

"In minerals processing control is vital to increasing performance and output of a plant. Model predictive control (MPC) is one of the most effective control strategies used in process industry. Sbárbaro (Sbárbaro and Del Villar, 2010), Asbjörnsson (Asbjörnsson, 2015), and Légaré (Légaré et al., 2016) have for example highlighted the possibility to simulate, develop and tune control systems using plant simulators within minerals processing. In more recent years the use of model predictive controllers have increased, and many process industries now utilize more advanced control methods to regulate their processes, raising the question regarding how to, build, test and verify a proposed control solution successfully. In this research, a linear model predictive controller is formulated and applied to a simulator of an existing tertiary crushing circuit. The circuit has in previous work by Johansson (Johansson, 2017) been modeled in MATLAB Simulink and calibrated relative plant data to an average error of less than 10% over 8 hours of production. The work demonstrates how to formulate the controller model structure to describe conveyor belts, storage components, screens, crushers, and control objectives for a minerals processing circuit. The work illustrates how to apply and successfully evaluate possible upsides in a circuit. The advantage of a crushing circuit simulator is that it can be configured, tuned and modified in any possible way, which is of great benefit to developers and engineers. Additionally, examples of how to use estimated measures to improve the performance of the plant are demonstrated. The control performance is finally evaluated for three different controller configurations."

Jan 1, 2018

By Briony C. Ruse, David V. Boger, Fiona Sofra1

"The sustainability of the mining industry must be addressed through improving tailings management. The use of thickened tailings and pastes stems from a paradigm shift towards designing tailings disposal sites to suit their surrounding environment, rather than manipulating the environment to accommodate the tailings. Thickened tailings and pastes usually exhibit non-Newtonian behaviour, so a thorough understanding of the rheological characteristics of the material is required in order to determine the disposal plant operating conditions.As environmental factors translate into economic issues, minimising waste production using dry disposal methods is gaining popularity. The use of rheological information is of high importance in evaluating the spreading characteristics, the transportation and the dewatering of thickened mineral tailings. The principles outlined may be applied to many industries encompassing a wide range of waste materials. The main obstacle to the widespread implementation of dry disposal methods has been the high initial capital cost of the methods due to the dewatering step, and the high cost of pumping thick suspensions across any great distance. Proper and thorough costing of tailings disposal activities combined with an accounting approach that shows closure and post-closure care costs on a per tonne basis of tailings disposed throughout the life of the tailings facility will show that dry disposal methods are more favourable than they might seem on initial appraisal."

Jan 1, 2003

By T. V. Chnyrenkova, J. Troncoso, V. A. Luganov, G. P. Kluev

"Arsenic-gold bearing ores are used as flux in smelting or are leached out with extraction of gold. For decreasing arsenic content in processed materials and for breaking up the lattice and opening up of gold the raw materials are roasted. Some regularity was established for sulfidizing of arsenic bearing compounds in a presence of pyrite and for oxidation of ores and concentrates in the presence of soda.This article analyses the results of laboratory and pilot testing of dissociating and oxidizing roasting of gold-arsenic bearing concentrates. During the dissociation roasting under vacuum arsenic is sublimated into elemental and sulfide forms. This process allows minimizing the negative influence on the environment but requires costly engineering solutions. Roasting in a limited quantity of oxygen in the gaseous phase makes it possible to sublimate arsenic in the form of oxides and sulfides and may be carried out in fluid bed furnaces."

Jan 1, 2003