Search Documents

By G. P. Wong

"The Inco Matte Separation process was the first commercial application using mineral processing techniques to separate nickel from copper from a slow-cooled matte in Sudbury since 1945. In Inco Sudbury operations, bulk sulphide concentrate containing chalcopyrite, pentlandite, pyrrhotite and some gangue minerals is flash smelted and converted to Bessemer matte. During the controlled slow-cooling of the Bessemer matte, discrete mineral grains of new mineral phases are formed: copper sulfide precipitates as chalcocite (Cu2S), nickel sulfide as heazlewoodite (Ni3S2) and a Cu-Ni-Fe alloy is also formed. Flotation is employed to separate Cc from Hz under high lime conditions (pH>12) with diphenyl guanidine (DPG) as both collector and frother.A simplified matte separation flowsheet is as follows. After grinding, the Cu-Ni-Fe alloy is removed by magnetic separation. All precious metals are recovered in the metallic alloy. Following the rougher flotation, a Cu concentrate is produced after cleaner and re-cleaner flotation in mechanical and column cells. Two Ni concentrates are produced: a high-grade Ni product containing less than 0.8% Cu from the scavenger column tails and a low-grade Ni product containing 5% Cu from the middlings circuit tails. A stream containing the inseparable Cc and Hz from the middlings circuit is generated and recycled back to the smelter. The quantity of this stream is typically about 3% of total feed and can be as high as 5%, greatly decreasing the overall matte separation efficiency. The large mass of the recycle stream is a direct result of poor Cc/Hz separation selectivity in the middlings circuit. The middlings circuit, consisting of a thickener, a regrind mill and two columns, processes two streams: cleaner tailings and scavenger concentrates. The thickener contributes significantly to oxidation due to the long residence time of the pulp in this unit."

Jan 1, 2003

By Victor V. Karmazin

"The appearance of the precise equipment for analysis of results of the laboratory tests with using of the computer processing allows raising accuracy of the estimation of the expected indexes of the mineral processing. Certainly, laboratory tests will not be able to substitute completely industrial ones, but allow reducing the amounts of the industrial tests, that vastly reduces the cost of technological forecast and preparation of data for projection.Calculation of the potential indexes of mineral technology (mass yields and the metal content in products) is fulfilled on the base of results of measurements of the mineralogical liberation parameters using special formulas.The quality of the concentrate ßc = a + ?l • ?s • ?i (ßt - a) can be achieved on a level of the theoretical metal content of a mineral - ßt only if coefficients of mineral processing, of liberation ?l and selectivity ?s of grinding, effectiveness of separation, will reach 1 (a - metal content of the row ore).Increase ?l by overgrinding automatically decrease ?s, and only by destroying of particles of ore along surfaces of accreting of minerals (?i = 1) and when values of all three coefficients will aim to 1, then ßc ? ßt.The degree of liberation of the useful mineral is the ratio of mass of free grains of the useful mineral in the product to general mass of the same mineral in this product. The factor of the liberation, which is defined by curves of dressability by angle of slop of the curve of the elementary faction - ?, is Kr=1 – tga. Kr changes from 0 to 1 when a changes from 45o to 0o. The liberation is reached by grinding of the material, although degree of the liberation, as a rule, is lower than the degree of the grinding."

Jan 1, 2003

By Verónica Fernández, Jaime Solari

"The Chilean Environmental Impact Assessment System (EIAS) of investment projects was created in 1994, date in which the General Environmental Law was enacted. The compulsory environmental approval of projects began in 1997 when the Regulation (S.D. 30/97) was officially issued. By beginning late to regulate the environmental effect of investment projects, Chile could take advantage of the international experience in the matter and therefore, the EIAS has many of the attributes of successful environmental assessment systems elsewhere. Thus, the main characteristics of the Chilean EIAS are: preventive, single-window, specific to certain projects, multi-agency assessment at the regional scale, 3 kind of applications, deadlines, citizen and native communities participation, link to relevant permits, definite conditions of approval/rejection, review of applications by an ad hoc institution. The Chilean EIAS has allowed during the period 1997-2013, the review of 21,110 projects for a total investment value of US$ 408 billion, of which a 76% have been approved. In the case of the mining projects, the corresponding figures for the similar period are 1,257 projects for a total investment value of US$ 119 billion, of which 78% projects were approved. The experience derived from the environmental impact assessment of mining projects indicates that Chile has been successful in linking together mining development with environmental protection. There is still little prejudice against mining and this is a still a largely welcome economic activity at all levels in the relevant regions of the country. The challenge that mining companies face today in Chile is to improve the sustainability of projects and operations, by learning to share scarce and valuable resources (water, glaciers, renewable energy) with the local and native communities, through a process of dialogue whereby mining development also generates benefits for these communities."

Jan 1, 2014

By Claudia Ríos Figueroa, Gonzalo Montes-Atenas

"Among the many variables mentioned in the literature that may influence the froth flotation performance, particle size is perhaps one of the most renowned. Empirical knowledge has indicated that recovery of fine particles will inevitably drop below certain particle size threshold. Several processing alternatives have been suggested to improve the recovery of fine particles. Some of these initiatives have been reached the status of patents and other intellectual property related documents; however, there is still a disconnection between the scientific knowledge available and the industrial operations practicalities implemented to address this matter. In fact, in general terms, none of these ideas or processes concepts have become a final solution to this problem. At first glance, economical reasons may be argued as the main cause hindering the development of these and other ideas, but it would be an oversimplification as technical issues behind them are still themes to be discussed and sorted out. This study aims to review technical aspects behind scientific ideas and processes concepts suggested to solve the problem of low beneficiation of fine particles in froth flotation. The analysis was performed using the theory of inventive problem solving (TRIZ) which allows identifying technical gaps these initiatives have not considered or overlooked. Statistically the scientific databases indicates that reports on fine particles froth flotation only represented less than 50% of all reports involving fine particles processing. Most of the solutions derived from classic contradictions derived from bubbles and particles hydrodynamics only (reducing the bubble size or increasing the turbulence would increase the rate of bubble-particle aggregates formation but may reduce the recovery). This contradiction encompasses a small range of contradictions possible to be accounted and to be resolved. The method is expected to provide insights towards designing definitive solutions for the industry in this field."

Jan 1, 2014

By Han Long, He Fayu, Sun Chuanyao

In global mining sector, when people mention "China Factor", usually they refer to China’s huge demands for mineral commodities, which had been driving the world mining industry into late "Super Circle". Few people pay attention to Chinese research capabilities and resources, which actually grows with Chinese economics in last three decades in such a soaring speed that you can simply feel it by the number of papers and attendees in recent IMPCs. In China, currently there are 33 universities and colleges where mineral processing discipline is established, and more than 20 research institutes dedicated in mineral processing area, with the largest number of students, teachers and researchers in the world. Due to the characteristics of Chinese mineral resources, Chinese researchers have made tremendous efforts on R&D of the process and reagents for those low grade, fine dissemination, and complex minerals resources, such as low grade hematite, diaspore, complex poly-metallic sulphides, as well as those minerals rich in China, including scheelite, cassiterite, and rare earth etc. with a special emphasis on the comprehensive utilization. Those research achievements not only successfully commercialized in China, but also have great potential for international cooperation. With continuation of globalization , Chinese government has been encouraging the international R&D cooperation in various areas at all levels, and the funding mechanism is well established with more 400 projects were sponsored in last year,in which,however, the mineral processing related projects are very few. Considering the fact that a large number of Chinese companies or Chinese capitals investing in the mining sector worldwide, more opportunities for international cooperation in this filed wouldbe emerging and increasing, while the factors like complementary, IP, government policy, system and culture difference still need to be addressed properly.

Jan 1, 2014

By Gustav Hawlitschek, Henrique Kahn, Carina Ulsen, Renato Contessotto

"The problems related to waste dumping increased with the growth and development of large cities. In the U.K., more than 50% of landfill waste comes from construction use and the U.S. alone produces around 200 to 300 million tons of CDW annually. The exhaustion of natural sand deposits close to large urban centres stimulates the recycling of construction and demolition waste for the production of recycled aggregates as a construction material. This paper presents a flowchart for the production of recycled sand with low porosity and regular shape by the selective removal of the cement paste attached to recycled aggregates. The products characterization was carried out by the determination of the particle size and shape distribution, chemical and mineralogical composition, heavy liquid mineral separation and quantification of all present phases using a scanning electron microscopy with automated image analysis (SEM-MLA). The comminution of CDW by vertical shaft impact crusher made possible the production of a lower porosity recycled sand. The heavy liquid mineral separation showed that the proportion of low porous phases (d>2.5 g/cm3) is very high, exceeding 70% of the weight, encouraging further mineral processing separation to obtain a fine recycled aggregate with less cement paste content. The mineralogical characterization by XRD and SEM indicates that the main phases are tectosilicates, phyllosilicates and calcite which one can be attributed to both calcareous aggregate and cement paste. The precise quantification of cement paste and calcite/dolomite alone is just possible by automated image analysis. The characterization results demonstrated that proportion of phases with no cement paste attached increases progressively in denser products. The results of heavy liquid separations and image analysis are comparable and automated image analysis can be used for the characterization of phase content and their main associations."

Jan 1, 2014

By A. V. Bauman

"Important for thickening processes is the ability of slurries to form under certain conditions aggregation and sedimentation stable systems. Substantial part of difficult to sediment solid particles in such systems may be in colloidal state. The technique to study the sedimentation and aggregative stability of the slurry developed by the author with co-authors makes possible to define kinetics of changes in the aggregative stability of the system with solid phase varying concentration in it and produce data on sedimentation stability of the system in preliminary investigation of the thickening process. Research of aggregative and sedimentation stability of the slurry complement standard methods of laboratory studies to prevent errors in development of water-slime thickening balance and water circulation to design new and upgrade existing processing plants. Statistical analysis of process audits of more than one hundred upgraded and newly commissioned processing plants carried out in recent fifteen years showed that more than two-thirds of problems arising in commissioning the processing plants are associated with misdesign and errors in thickening and water circulation system. Among the main reasons of process design failures are: non-conformity of actual characteristics of the raw material to design characteristics, low quality of preliminary studies at the stage of sedimentation process simulation, design failures, wrongly selected equipment for the thickening and water circulations systems. As of today a number of problems associated with laboratory studies of sedimentation process, first of all, with interpretation of precipitation curves produced at the stage of laboratory refinement of the thickening process have been pinpointed. (Bauman A.V. Outstanding issues in design of thickening and water circulation diagrams in processing plants // Ore processing. 2016. ?3 P. 58-62) ?????? ?.?. ?????????? ??????? ?????????????? ???? ???????? ? ??????????? ?????????????? ??????. // ?????????? ???. 2016. ?3. ?. 58-62))"

Jan 1, 2018

By A. J. Lynch, L. Ergun, M. Oner

"A research program on modelling cement grinding circuits has been in operation at Hacettepe University, Ankara, for four years. It has concentrated so far on tube mill and air separator grinding circuits for cement clinker, with emphasis on plant sampling surveys, including axial sampling inside the tube mills. The methodology is to use plant data to build the models and to supplement this by laboratory data where necessary, for example the determination of breakage functions. The plant data come from comprehensive sampling surveys and so far 33 surveys of clinker grinding circuits have been carried out in 9 plants. The operating conditions have been• mill sizes – 3.2 to 4.8 metres diameter and 8.5 to 15 metres long,• mill feed rates – 46 to 158 tonnes per hour,• air flow through mills – 25000 to 125000 cubic metres per hour,• cement clinker work indexes – 10.3 to 18,• separator sizes – 2. to 3.1 metres diameter,• separator feed rates – 132 to 689 tonnes per hour,• separator speeds – 12.3 to 21 metres per second.The ball mill model is Whiten’s perfect mixing model and the separator model is the Tromp curve with a fish-hook. This paper emphasises on the importance of calculating the breakage rates and the discharge functions with three case studies at five different circuits which were selected for discussion because they show how particular features of circuit operation can be included in the general models. Size distributiongraphs are used to illustrate every aspect of the discussion.In case I the special emphasis on calculating the breakage rates and discharge rates separately is given in a high pressure grinding roll-ball mill-separator circuit. The tonnes of each size fraction in the mill and the calculated values of R/D, D and R are determined. The values of R per mw are also given to allow comparison with mills of other sizes. The circuit allows the comparison of the static type (V Sep) and dynamic type separators (SKS). Comparing the reduced efficiencies shows that the dynamic separator is slightly more efficient than the static one.In case 2 data are given from two compartment tube mills having the same diameter and the motor power but different ball size gradation. The breakage rate particle size variation of the second chamber of two mills indicate that having finer ball size distribution causes higher breakage rate values."

Jan 1, 2003

By Ashok M. Raichur, S. P. Vijayalakshmi

"Recent advances in technology and the growing environmental concern have laid emphasis on the usage of fine clean coal. Coal fines are also generated in large amounts during various coal processing operations and are difficult to be treated, handled and disposed. Since most of the operations use water as the carrying medium, the fines so generated contain lot of moisture. Conventional technique for processing coal fines includes flocculation by a polymeric reagent followed by moisture removal using a rotary drum or a pressure plate filter, which produce a product with more than 30% moisture. Polymeric flocculants though required in small amounts, need high shear mixing for good performance and operate only in a narrow pH range. Moreover they increase the viscosity of the solution by many folds. Hence it becomes imperative to emulate newer methods for efficient fine coal processing. One such method is the novel use of microorganisms in coal processing.The present investigation deals with the utilization of two gram-positive microorganisms, Mycobacterium phlei and Bacillus subtilis, as bio flocculants and dewatering aids in fine coal processing. Preliminary characterization done on J-coal and M.phlei showed that they are negatively charged over most of the pH range. B.subtilis was found to possess positive charge below pH 4.7. The adhesion studies proved the high potential of microorganisms for adsorption to surfaces. Adhesion tests were conducted at various experimental conditions by varying parameters like pH and ionic strength of the suspension. Results obtained showed that adhesion is always higher in the presence of an electrolyte like KNO3 and most of the adhesion takes place in 15 minutes. With change in pH the amount of B.subtilis adhering on to J-coal remained almost constant and for M.phlei it decreased at higher pH values. Increase in ionic strength did not increase the adhesion of bacteria. Flocculation experiments confirmed the ability of the bacteria to act as bio flocculants. It was seen that about 98% of the coal settled in about 2 minutes on the addition of bacteria along with the addition of the electrolyte. The electrolyte was found to be indispensable for efficient flocculation of the coal suspension and for the attainment of a clear supernatant after flocculation. Also the optical micrographs revealed the formation of large, tight flocs when the electrolyte is present along with the bacteria. Further, flocculation tests were done in the pH range of 2-10 and the flocculation efficiency was found to be independent of pH."

Jan 1, 2003

By Olgac Kangal, Ali Guney, Gulay Bulut, Guven Onal, Ayhan A. Sirkeci

"This paper presents the results of pilot scale column flotation applications in the two different copper concentrators in Turkey. The Kure Copper Plant is located in the Black Sea Region of Turkey. There are four types of copper ore formations in the Küre region. The so called disseminated ore contains 60-70% siliceous minerals of which Cu content is around 0.5%. The remaining three ore types in the region are generally named “massive ores”. The massive ores may assay up to 15% Cu and the major gangue mineral is pyrite associated with relatively little amount of silica. The main copper mineral in all formations is chalcopyrite that is generally finely disseminated in pyrite therefore satisfactory liberation requires ultrafine grinding especially in the case of the massive ores.A blend of these ores, containing 1.7% Cu on average, is fed to the Küre Copper Concentrator whose capacity is 1.2 million tons of ore annually. Unfortunately, today the plant operates below its designed capacity treating around 550,000 tons of ore per year. The design of Küre Copper Plant was undertaken by the Outokumpu Company of Finland. The operation of the plant is almost automatically controlled and the feed, the concentrate and the tailings are assayed for copper by on-line XRF analysers. The particle size analysers are also connected to the grinding circuit. The feed material is ground almost below 50 µm and the flotation is conducted around pH 11.2 using Hostaflot X-231 (a trade mark of Hoechst) as the collector. Apart from the rougher cells, there are four cleaning stages after which the final concentrate is produced. A very fine grinding requirement for an adequate level of liberation makes successful flotation difficult and consequently the final concentrate can hardly assay above 16% Cu leading to copper losses around 20% in the tailings that contains 0.3% copper."

Jan 1, 2003

By P. Gao, J. W. Yu

"Magnetizing roasting-magnetic separation is an important route for the beneficiation of refractory iron ores. In this investigation, a pilot-scale fluidized magnetizing roasting reactor was introduced and used to study the effects of roasting temperature and the flow rates of reducing gas CO and fluidizing gas N2, on the magnetizing roasting performance of an Anshan-type carbonate-bearing fine iron ore. The results showed that the hematite was almost reduced to magnetite by a gas mixture of 4 m3/h CO and 1 m3/h N2 at a roasting temperature of 540 °C. Under the optimized conditions, a high-grade magnetic concentrate assaying 66.1 wt.% Fe with a recovery rate of 91.2% was achieved from an Anshan-type carbonate-bearing fine iron ore assaying 42.0 wt.% Fe. The XRD, VSM, and optical microscopy analyses revealed that the siderite was successfully converted to magnetite by roasting. Some coarse hematite particles were difficult to reduce to magnetite completely; however, these generated magnetite particles with a fine hematite core could also be effectively recovered by magnetic separation after liberation from gangue minerals due to their strong magnetism. INTRODUCTION Magnetizing roasting followed by low-intensity magnetic separation has been considered as an effective solution, both technologically and economically, when upgrading refractory iron ores (Zhang et al., 2012; Peng et al., 2012; Li and Zhu, 2012). According to the type of roasting reactor, the magnetization roasting can be divided into shaft furnace roasting, rotary kiln roasting, and fluidized bed roasting (Zhu and Li, 2014).Shaft furnace magnetization roasting system is mainly composed of heating and reduction processes. The hematite ore is first heated to 700~800 °C in the heating zone, then falls into reduction zone where the weakly magnetic hematite is reduced to magnetite by coke oven gas at 550~600 °C (Yan et al., 2012). However, several years of engineering practices indicate that the shaft furnace can only process the hematite ores with a granularity of 15 ~75 mm, and the shaft furnace roasting is also characterized by heterogeneity of roasted product. Hence, the shaft furnace magnetization roasting technology is gradually replaced by high-gradient magnetic separation with the development of high-gradient magnetic separator. The rotary kiln generally handles the hematite ores with a grain size of less than 30 mm (Zhu and Li, 2014), however the formation of clinker ring in the rotary kiln will affect the yield of iron resource. In the fluidized bed furnace, the hematite ore is shaken up by an upward current of gas which maintains the individual particles in suspension (Yu et al., 2018). The precise adjustment of the gas velocity to the particle size and the specific weight of the hematite ore, make it possible to generate a floating mixture of gas and solids which behaves almost like a liquid (Yu et al., 2017a). The process is reported to have the following advantages over the other roasting techniques: ease of control due to absence of moving parts within the reactor, homogeneity of roasted products, ability to handle fine particles, and high efficiency of heat transfer and mass transfer (Li et al., 2015; Yu et al., 2017b). However, the simultaneous heating and reductive magnetization of hematite ore occur at the same place in the conventional fluidized bed reactor. Therefore, the reductive atmosphere, as well as the safety and stability of anti-explosion are hard to be controlled. Besides, the roasting temperature for conventional fluidized bed furnace is usually up to 950~1150 °C (Liu et al., 2017). Thus, the formation of clinker ring caused by high temperature will affect the operating efficiency."

Jan 1, 2018

By Hajime Miki, Mutia Dewi Yuniati, Tsuyoshi Hirajima, Keiko Sasaki

Acid mine drainage is mainly due to pyrite/arsenopyrite oxidation processes, and suppressing such processes is important issue. As a promising process it is reported that silicate ion can complex with catechol (1,2-dihydroxybenzene) and this complex is oxidized to a solid silica layer on the surface of those sulphide minerals. Detailed behavior was investigated from the result of electrochemical experiments. Results of polarization potential showed that oxidation peak can be seen only in the presence of both silicate ion and catechol addition at this peak potential and this peak can be identified as silicate-catechol complex oxidation to silica. Potentiostatic experiments indicated the dissolution kinetics of pyrite. Untreated pyrite dissolution rates were higher than pyrite treated with catechol and silica solution. To enhance the silica layer reaction on pyrite, the pyrite potential was held at 550 mV vs. SHE in catechol silica solution. This pyrite dissolution kinetics was almost the same as untreated pyrite. Potential hold followed by drying for 30 min process resulted in much lower pyrite dissolution rates. Drying is important for development of the silica layer. Analysis of this potentiostatic curve provided a way to estimate the thickness of the produced silica layer and kinetic information of treated/untreated pyrite. Untreated pyrite showed thinner initial layer thickness on the surface of pyrite (oxidized passive layer, not silica) and higher oxidative kinetics of pyrite compared with silica-coated pyrite.

Jan 1, 2014

By R. Shiva Kumar, G. Sreedhar, S. Sharma

Some of the Indian origin iron ore deposits located in Bellary, Karnataka province are having peculiar characteristics of Iron ore deposits (Hematite) having Iron above 64% and 30-40% lump (-30+6mm) recovery which are not suitable to use in blast furnace due to not meeting the specification of Tumbler Index and Abrasion Index. In general for high grade Iron ores, process flow sheet involves crushing and screening (dry/wet). In the contest of high grade Iron ores located at Bellary sector of Karnataka state in India, lump generated from this process could not attain the required physical properties (Tumbler Index, Abrasion Index) and metallurgical properties , even though the grade of the lump ore is above 64% Fe. Washing techniques like Drum scrubber and Log washer play major role in improving the metallurgical properties of Iron ore lumps by removing the light and hard layers of clay, silica coated over the lumps. In this study the effects were compared of drum scrubbing and log washing on iron ore lumps. It is found that by incorporating simple washing technique i.e. drum scrubbing or log washing, Tumbler Index of Iron ore Lumps could be increased from 74% to 78% which is acceptable for use in Blast furnace. From the Drum scrubber and Log washer tests, it is clear that Log washers have an edge over Drum scrubber in removing hard coated clay on surface of Lumps. This simple washing technique facilitate us to utilize the lumps directly in blast furnace and eliminate the unnecessary crushing and grinding of the ore so as to meet the specifications of Sinter fines and pellet feed.

Jan 1, 2014

By D. B. Sundar Ramam

In the recent past, a paradigm shift in terms of resource utilization and beneficiation practices is experienced by the Indian mining and mineral sector. Depleting iron ore reserves coupled with increasing demand for low-alumina iron ore fines to improve blast furnace performance in terms of productivity and reduced slag rate necessitate intensive beneficiation of iron ore. The task is even difficult for Indian iron ores, which are generally high in iron content and at the same time characterized by aluminous gangue. In 2006, M/s Tata Steel commissioned a state-of-the-art Jigging Plant (Batac Jig) at Noamundi Iron Mine (NIM), mainly to reduce alumina in iron ore fines. The jigging plant is incorporated in the existing beneficiation circuit to treat ?10+0.5mm size fraction of classifier fines. Over the course of plant stabilization while the plant could deliver desired ore upgradation and average product alumina, variability in terms of alumina content has been a concern. This paper discusses a case study of process parameters optimization in jigging operation to achieve consistent product quality while improving the effectiveness of gravity concentration for the beneficiation of Noamundi iron ore also to take care of inferior plant feed (input) grade year on year. The operating variables used to optimize jigging operations include bed height, pulsion and suction time, particle size, strokes, and plant throughput rate.

Sep 1, 2012

By Rodney J. Hundermark, Sharif Jahanshahi, Shouyi Sun

"The major platinum producers in South Africa make use of electric furnaces for the melting of platinum group metal (PGM) bearing nickel – copper concentrates. To gain better understanding of the furnace operation, research was conducted at CSIRO Minerals in Melbourne, Australia. One aspect of the research project was the investigation of the factors affecting the electrical conductivity of melter type slags.Electrical conduction in slags can occur through two mechanisms: ionic and electronic. There is good understanding of the ionic mechanism. In slags containing high levels of iron, the dominant mechanism is electronic as a result of charge hopping (electrons or holes) between ferric and ferrous ions. There is limited understanding of the electronic mechanism and one of the aims of the research was to investigate this mechanism further.Experimental work was carried out at 1450 °C on Al2O3–CaO–FeOx–MgO–SiO2 slags similar in composition to the melter slags (typical composition range (wt%): Al2O3: 5, CaO: 5-15, FeOx: 10-30, MgO: 15-25, SiO2: 40-60). The approach was to vary the oxidation state of three different basicity slags and measure the conductivity response. The slags had molar (CaO+MgO)/(Al2O3+SiO2) ratios of 0.43, 0.64 and 0.94 and FeOx contents of up to 40wt%. A twoelectrode technique was employed with a shallow layer of slag contained in a magnesia crucible. The small amount of slag facilitated relatively quick equilibration (up to one hour) with the gas atmosphere. Experiments were typically started in air and sequentially reduced using different ratios of CO and CO2 gases.Conductivity increased with increasing basicity and increased significantly with iron oxide content. Above 20wt% FeOx, electronic conduction was significant and the conductivity varied with the oxidation state of the slag. The typical response of the conductivity to the change in oxidation state was the following: starting in air, as the slags became more reduced, the electrical conductivity increased to a maximum at around pO2 = 10-7 to 10-4 atm and then decreased with further reduction. The value of the pO2 at which the maximum occurred was dependent on the total iron oxide content and basicity of the slag. The magnitude of the conductivity of the slags increased with increasing FeOx content in a range of 20 to 170 S/m for 20 to 40wt% FeOx. For a given FeOx content in the slags, the oxidation state dependence of the conductivity varied with slag basicity. The trend observed was that the maximum in the conductivity occurred at higher oxygen partial pressures for the lower basicity slags."

Jan 1, 2003

By A. Gueciouer, A. Akkouche, K. Chalah, A. Benmounah

"Drilling solid waste is a typical industrial solid waste, and it is a major pollutant source to ecological environment. Generally, waste management dewatering systems separate solids and fine particles from the liquid phase of drilling fluid, thereby leaving a clarified aqueous solution and allow the cleaning of waste fluids. Typically, dewatering waste management systems clean drilling fluid through coagulation, flocculation and/or mechanical separation. Chemicals used in dewatering are based on the coagulation-flocculation process, which it facilitate the removal of suspended solids and colloidal particles. The factors which can promote the coagulation-flocculation are velocity gradient, contact time, and PH. The objective of this work is to optimize a formulation adequate for dewatering based on the coagulation-flocculation process used coagulant (Aluminum sulphate), anionic flocculants (Partially Hydrolyzed Polyacrylamide) and anionic polyelectrolytes (in solid form with linear chain with very high molecular weight). The results obtained show the good efficiency of the coagulant and flocculants. INTRODUCTION Rig site dewatering of drilling fluids with recycling of processed water can help an operator to comply with environmental rules by reducing volumes of waste and reducing long term liabilities. It can also reduce disposal costs and provide a cleaner drill site overall. Most of the environmental concerns during the 1980s involved hazardous materials and toxic wastes. Drilling fluids, many of which are chemically benign, have escaped many of the difficult-to-comply-with rules and regulations. During the 1990s, however, operators may be required to submit a written plan for liquid waste reduction for even nonhazardous materials. Many states and local agencies may institute total bans on oil field wastes. Drilling rigs typically produce about 1 bbl of liquid waste for every 1 ft of hole drilled. Thus, a typical drilling operation can produce a large quantity of waste [1]. To improve the dewaterability of sludge, different pretreatment processes have been widely studied and developed including thermal, chemical, magnetic, mechanical, acoustic, electric, electro-acoustic and their hybrid treatment processes [2]. Rig site dewatering (figure 1) is the process of injecting coagulants or flocculating chemicals into the mud entering a large clarifying centrifuge. Coagulation occurs when the solid and allowing it to be attracted to other solids by van der waals forces. Flocculation is the binding of individual solid particles into aggregates of multiple particles. It is physical, rather than electrical, and occurs when one segment of a flocculating polymer chain absorbs simultaneously onto more than one particle [3]."

Jan 1, 2018

By Xiao Jian Li, Dai Xiong Chen, Jian Wen Yang

In one kind of lead and zinc bearing polymetallic ore containing secondary copper, the characteristic of low sulfur, high zinc, and particularly the existing of secondary copper minerals can lead to lead concentrate with high content of zinc because the dissociation of Cu2+ in the grinding process may have an activation influence on sphalerite. Considering its process mineralogy analysis, a new process of seperation of lead and zinc has been put forward. The experiments focused on the analysis of the advantages and disadvantages of the inhibition effect of traditional adjustment reagent + zinc sulfate on activated sphalerite compared with new organic inhibitor, polysaccharide xanthate. According to the numerical calculation and test results, a reagent system of polysaccharide xanthates is developed, which has a good inhibition effect on Cu2+ activated zinc minerals, achieving high-efficiency separation of lead and zinc. A new reagent system and flotation process was developed under optimal conditions. Under the condition of the run-of-mine ore containing 2.37% Pb and 12.48% Zn, lead of 67.69% grade and lead concentrate with the recovery rate of 86.06%, zinc of 60.32% grade and zinc concentrate with the recovery rate of 96.15% were achieved.

Jan 1, 2014

By D. Saramak

Investigations over the application of hybrid comminution circuits with the High-Pressure Grinding Rolls (HPGR), on the main comminution stage on the basis of the lime and cement industry, were presented in the paper. Two crushing circuits were investigated, the first HPGR-based and the other one, with conventional jaw crusher. The results presented in the article confirm that hybrid comminution circuits with the application of HPGR are innovative ones, and they assure achieving the technological and economic competitiveness in the mineral raw materials processing industry. They are much more favorable in terms of the final product fineness and capacity but insignificantly less effective about the unit energy consumption. Technological performance of conventional crushing circuit and HPGR-based one were also compared in lab scale. The circuit with HPGR application gives finer products both on crushing and grinding stages. The average particle size reduction obtained in HPGR-based circuit is as much as twice greater, comparing to the conventional crushing devices. Keywords: comminution, HPGR technology

Sep 1, 2012

By Yuri L. Nikolaev

The treatment of placer gold with fine gold, associated with gold-bearing sulfide minerals, heavy minerals and oxidized minerals such as manganowolframite (gubnerite) is not an easy task. In this case, this complex material cannot be treated using physical separation methods such as deep concentration and finishing, magnetic separation and solvent extraction. This technology is usually employed in gold washings finishing plant. The easiest way to recover precious metals in the form of an easy-to-sample saleable product is metallurgical treatment. This paper describes the application of pyrometallurgical processes with oxidative roasting, re-cleaning of cinders (if required) and ore-thermal smelting for producing gold bullion. Hydrometallurgical treatment of slags as an additional operation is recommended in order to maximize recovery of valuable metals. After this treatment, a barren leaching cake rich in PGM can be sold in the market. PGM can be collected as gold-silver alloy during smelting which allows the phase formation of polymetallic matte due to specific composition of fluxes. The PGM are then in the form of saleable gold bullions in the refinery.

Sep 1, 2012

By R. Chowdhury

Axis House manufactures and supplies alkylhydroxamate reagent of various carbon chain lengths for application in flotation of oxide copper and other minerals. As part of reagent performance improvement the structural factors of hydroxamate are examined by various analytical tools in particular with X-ray diffraction of single crystals. In a recent publication, the structure of n-octylhydroxamic acid and its corresponding potassium salt are presented with findings of hydroxamic functional group geometric preference, H-bonding, keto-enol tautomerisation, acid-salt aggregation and alignment of carbon chain. In this paper an example of branched alkylhydroxamate 3, 5, 5-trimethylhexylhydroxamate will be presented and compared with the result of linear alkylhydroxamate.

Sep 1, 2012