Search Documents

By M. Kosugi, M. Kawata, J. V. Satur, K. Mitsuhashi, R. Kawarabuki, W. Kracht, Y. Ebisu

Copper concentration is becoming more difficult because remaining copper ores are more complex and of finer copper mineral grain size, making copper minerals harder to float because of the fine particle size required to liberate the valuable species. The purpose of this work was to study the flotation behavior of fine copper sulfide ores at different conditions of agitation and aeration. The experimental campaign was carried out in a laboratory Denvertype flotation cell of 1 L volume modified to be operated with forced air that allows decoupling air flow rate and agitation speed. Four ore samples from Chile were used, all of them containing copper sulfides such as chalcopyrite, bornite, chalcocite, and tennantite, but with varying grain sizes and compositions. Preliminary flotation tests for establishing the flotation conditions of grinding size and collector dosage were conducted before the kinetic flotation tests that were carried out at different agitation speeds varying from 900 to 1300 rpm for gas flow rate ranging from 1.6 to 7.2 L/min. The flotation products were analyzed by ICP-MS and MLA (Mineral Liberation Analyzer). The results showed that high agitation speeds with corresponding air flow rates resulted in better recovery than moderate agitation speed and air flow rate, and an excess in gas flow rate resulted in bad performances. The flotation rates of the fine copper minerals were improved despite the different improvement rates among the fine size fractions. The impact of these operational variables, however, was different when comparing the results for the four ore samples. While it was found that the order of floatability in the four samples was the same, that is, chalcocite > tennantite > bornite > chalcopyrite, the kinetic constants of the copper minerals in the samples were different, indicating that mineral composition in the sample affects the flotation kinetics.

Jan 1, 2018

By F. S. Hoseinian, K. Filho, D. Deglon, T. Souza, M. Safari

"This paper investigates the reverse flotation of hematite in three laboratory flotation cells with very different contacting environments. The main objectives are to investigate the recovery of coarse quartz by flotation and fine hematite by entrainment. The laboratory flotation cells used were the mechanical, oscillating grid and pneumatic cells. The effect of froth height and solid concentration were investigated in the mechanical and pneumatic cells. The effect of impeller speed and energy input were investigated in the mechanical and oscillating grid cells. Froth height results show that coarse quartz particle recovery decreases almost linearly with increasing froth height due to increased detachment of coarse quartz particles in the froth. Fine hematite particle recovery also decreases almost linearly with increasing froth height due to decreased water recovery and associated entrainment. Agitation/energy input results show that coarse quartz particle recovery increases with increasing impeller speed to an optimum, after which this decreases dramatically. The increase is due to improved gas dispersion, generation of smaller bubbles and increased bubble-particle collision and attachment. The decrease is due to significantly increased bubble-particle detachment at higher impeller speeds. The recovery of coarse quartz particles in the OGC is higher than that in the mechanical cell with an optimum at a much lower energy input. Solids concentration results show that both mass recovery and water recovery increase with increasing solid concentrations. The pneumatic cell achieves higher mass recoveries and lower water recoveries than those in the mechanical cell at equivalent solids concentrations and operating conditions. INTRODUCTIONFlotation is a selective process for separating different minerals from each other. The flotation separation efficiency depends on the recoveries of the mineral species by both true flotation and entrainment (Neethling and Cilliers 2009; Wang et al. 2015). Both chemical variables and hydrodynamic conditions within the flotation cell affect the recovery and selectivity of the flotation process. Cationic reverse flotation of hematite is a common method for selective separation of quartz from iron ores to produce pellet feed. The presence of coarse quartz particles in the tailings and fine hematite particles in the concentrate are two major challenges in the reverse flotation of hematite (Vieira and Peres 2007)."

Jan 1, 2018

The flotation of nickel sulphide minerals is normally difficult in the presence of serpentine minerals due to the coating of serpentine particles on the nickel mineral surface. To improve the flotation, dispersants such as polyphosphate and carboxy methyl cellulose are normally used to remove the slime coating. However, in the flotation using high ionic strength process water, these dispersants are invalid due to their ionic nature. In this study, a new type of non-ionic dispersants, Pluronic triblock copolymers were examined with an objective of improving the flotation of ultrafine pentlandite (a nickel sulphide mineral) in the presence of lizardite (a serpentine mineral) in saline water. Three Pluronic triblock copolymers varying in solubility and hydrophile-lipophile balance (HLB) values were studied by flotation tests, settling tests and froth measurement. It was found that two of the copolymers improved pentlandite flotation against lizardite, and one copolymer deteriorated the flotation. The effect of Pluronic triblock copolymers on the flotation was actually linked to their dispersibility and foamability, which were governed by their physical properties. The two copolymers with a higher solubility or HLB value produced more stable mineral suspensions and more stable froth in the flotation resulting in better nickel grade and recovery in both rougher and cleaner flotation. Keywords: ultrafine particle, flotation, slime coating, dispersion, saline water, triblock copolymers

Sep 1, 2012

By Kaiwen Liu

Activated carbon is widely used in the removal of organic and/or inorganic contaminants from waste water due to its high surface area, porous structure, and specific surface reactivity. However, in practical applications, it is difficult to recover the activated carbon completely by screening or classification. In this project,we prepared a magnetic form of activated carbon (magnetic activated carbon or M-AC) by precipitation of iron oxides on the surface of activated carbon. The M-AC can be easily separated from effluents by applying an external magnetic field, thus it can be recycled and regenerated for reuse. M-AC was characterized by X-ray diffraction (XRD), specific surface area measurement, and scanning electron microscope (SEM).XRD results show that the major phase of coated iron oxides on activated carbon is magnetite (Fe3O4). The specific surface area of activated carbon was found to be reduced after the impregnation of magnetite particles on the surface. The SEM micrograph shows the aggregation of the iron oxides on the surface of activated carbon. M-ACwas found effective in removing DETA (diethylenetriamine) species and metal ions from solutions. Cu (II) with initial concentrations from 5 ppm to25 ppm in solution is removed by more than 99% with the addition of 0.1 wt.%ofM-AC. For the removal of 25 ppm DETA species from solution, an addition of 0.5 wt.% of M-AC is required due to the larger size of the DETA molecule. Moreover, M-AC showed a good loadingproperty for nickel and gold ions from solutions. M-ACshows a better adsorption capacityover activated carbon and its potential applications in carbon-in-pulp for gold leaching and waste water treatment. Keywords: magnetic activated carbon (M-AC),diethylenetriamine (DETA),metal ion,adsorption

Sep 1, 2012

By Hongchun Lou, Yan Zhang, Xianjun Lu

"The potential of Fe(NO3)3 modified attapulgite was assessed for the adsorption of phosphorous removal from aqueous solutions. Natural attapulgite was modified by Fe(NO3)3, and thus the composite adsorption materials could be obtained. Also phosphorous adsorption characterization on the iron-coated attapulgite was investigated in this research. Taken overall the results suggested that phosphorous adsorption capacity could be improved markedly by adopting ferric modified-attapulgite. The optimum phosphorous adsorption were developed in the experimental conditions of the solid-to-liquid Ratio 1g/L, the initial phosphorous concentration 5 mol•L-1, reaction time 120 min, temperature 25 ? and pH=4.0, the removal efficiency is 92.28% for the modified attapulgite. In comparison of batch experimental results of phosphorous adsorption onto natural and iron-coated attapulgite, it has provided much more likely the same change trend. On the other hand, the outcomes of this analysis indicated that ferric modified adsorbent was notably influenced by adsorption element over natural attapulgite. The Freundlich isotherm adequately described the adsorption course of phosphorous onto ferric modified-attapulgite with the correlation coefficient R2 goodness of fit of 0.9690."

Jan 1, 2014

By Scott C. Brown, Brij M. Moudgil, Ivan U. Vakarelski

The manipulation of the apparent hydrophobicity of particlute surfaces is necessary to achieve optimal selectivity in flotation processes. Previously a number of works have investigated the role of microscale surface and particulate morphologies on chemically modified substrates. These works have suggested that microscale surface asperities lead to an increase in flotation efficiency by assisting in the rupture of wetting films. Yet, in mineral processing the presence of surface asperities may lead to a reduction in flotation. The reason for this may-in part-be due to the presence of nanoscale irregularities at the interface. In this work, it is proposed that the presence of roughness at the nanoscale may have a dominant impact on the apparent hydrophobicity of mineral surfaces during flotation. It is suggested that as inter-asperity seperation distances are reduced capillary effects are enhanced for high energy mineral surfaces leading to the formation of liquid domains, which adversely impact hydrophobicity. In addition, as these distances approach the surfactant headgroup size obstruction of surfactant self-assembly process may occur, thereby further limiting flotation.

Jan 1, 2003

By Yi-jun Cao, Jin-cai Ran, Guo-sheng Li, Jiong-tian Liu, Li-jun Deng, Shu-lei Li

A fly ash sample from a power station in Guangdong province has been characterized by size separation, X-ray diffraction, contact angle measurements and X-ray Fluorescence. The ash sample had a loss-on-ignition (LOI) (%) of 15.54% and a large proportion of the unburned carbon was distributed in the +74 µm and -20 µm fractions. Contact angle measurements suggested that the removal of unburned carbon from the fly ash using flotation would present some challenges. The effects of various operating variables on the removal rate of unburned carbon (RUC) (%) and (LOI) (%) were determined using a cyclonic-static micro bubble flotation column (FCSMC). Within the range studied, the optimum diesel oil dosage was 1200 g/t, abies oil (frother) dosage was 600 g/t, pulp density was 20%, superficial gas velocity was 1.4 cm/s and circulating pressure was 0.20Mpa. Column flotation tests indicated that the FCSMC method a viable and effective separation process for removing the unburned carbon from the fly ash. Under the optimized conditions, a clean ash with 2.13% LOI and 94.21% RUC was obtained.

Jan 1, 2014

By J. Vilcáez

The copper extraction yield from thermophilic bioleaching of chalcopyrite depends on temperature, pH, and the oxidation-reduction potential (ORP), as well as the activity of the microbe used. We studied copper extraction yields obtained from chalcopyrite with three thermophiles, Acidianus brierleyi, Sulfolobus metallicus, and Metallosphaera sedula, under various pH and temperature conditions and with different initial amounts of ferric iron. The results indicated that the capacity of each thermophile strain to leach iron as Fe3+ differed, which affected the influence of pH, temperature, ORP, and microbial activity level on the yield of copper. Microbial activity can cause ORP to be close to the critical value (450 mV) at which copper extraction at 65 °C can be higher than that at 80°C. An initial pH of 1.5 retards the precipitation of jarosite, allowing temperatures as high as 80°C to result in copper extraction yields close to 100%. However, if a thermophile with a poor capacity to form Fe3+ is employed, 100% copper extractions can also be obtained at pH 2.5, because ORP is low as result of low amounts of Fe3+ in solution. Optimum temperatures for the growth of thermophiles did not always mean high copper extraction yields. Conversely, high biomass concentrations depending on the capacity of the thermophile strain to leach iron as Fe3+, can result in excess Fe3+ in solution, leading to the precipitation of large amounts of Fe3+ as jarosite. The bioleaching capacity of A. brierleyi was reduced or suppressed when insufficient initial Fe3+ was pro-vided to trigger the leaching reaction, whereas S. metallicus and M. sedula were less sensitive to the initial availability of Fe3+. This result confirmed that a direct enzymatic attack on the mineral surface could initiate the leaching reaction, but later ORP governed the leaching rate of chalcopyrite.

Jan 1, 2014

By E. V. Manlapig

"Some researchers postulate that the floatability of a particle in the streams of an industrial flotation circuit is a function of only its size and liberation properties. They do not discount the importance of reagent or surface contamination on particle floatability but assume that the reagent coverage or surface contamination of the particle surfaces is essentially uniform for particles of similar size and mineralogical properties when subjected to a particular chemical regime.In this paper, samples collected from laboratory batch flotation tests performed on different streams of Cominco Teck’s Red Dog lead cleaning circuit have been characterised with respect to their size, mineral association and mineral surface exposure. An analysis of this data set indicates that the flotation rate of a particle in an industrial flotation environment is a strong function of its size and also of the mineral composition of its surface (Figure 1). It is a function not only of the proportion of the most floatable mineral on its surface but of the floatability of the other minerals on its surface as well.Nodal analysis is a technique developed by the authors that can be used to determine if the ore floatability of a particle class is changing within an industrial flotation circuit. This technique is used within the paper to show that the floatability of all the different types of particle classes studied within the Red Dog circuit did not change significantly during the lead cleaning stage. However, it was also concluded that particles with the same size and mineral composition did not all float with the same rate in the individual streams of the flotation circuit, but with a distribution of rates. It is suspected that the particles within a size mineralogical class in this study have varying degrees of surface oxidation and that this results in varying particle flotation rates. Thus basing particle floatability on size and mineralogical effects, alone, in a flotation model is not always valid."

Jan 1, 2003

By Roberto C. G. Oliveira, Scott C. Brown, Brij M. Moudgil

The wettability or surface energy of particle surfaces dictates a number of multiphase ensemble interactions that have a significant impact in mineral processing. Dispersion, bulk powder handling and flotation behavior are just a few of the parameters that are largely due to the degree of hydrophillicity or hydrophobicity on particulate surfaces. Because of the inherent impact of surface wettability in nearly all industries, fields, and multi-phase interactions, a number of simple, precise and accurate techniques for accessing surface wettability or contact angle on macroscopic flat surfaces have been developed. However, these techniques cannot be directly applied to the particulate surfaces that are often in query. Though a number of techniques are available for accessing the wettability of particulate surfaces, these methods are either relative, application specific or prohibitively tedious. In this study, key features of existing techniques are combined to formulate an improved method to delineate particle wettability that is simple, versatile and capable of providing reproducible measurements in an industrial environment.

Jan 1, 2003

"The thiosulfate leaching process developed by Barrick to treat sulfidic high preg-robbing gold ores uses calcium thiosulfate as the leaching reagent for ores pre-treated by pressure oxidation, resin for gold recovery with sulfite/trithionate elution and reverse osmosis as a means of reagent recovery. A large portion of the research that led to the development of the technology was based on previous studies completed by different groups over the years, mainly focused on the ammonium thiosulfate system. Operational limitations in the use of the ammonia-containing recycled water in the pressure oxidation circuit were some of the main drivers for the change from ammonium to calcium thiosulfate for the development of the industrial scale process. One of the main aspects for successful gold extraction and recovery in the thiosulfate system is the pseudo-equilibrium reactions that drive distribution of the different gold species (in solids, solution and on resin) in the system. Previous studies have been focused on the thiosulfate reactions and equilibrium constants for the oxysulfur ions (thiosulfate, trithionate, tetrathionate). However, the literature around the effects of the different metal-oxysulfur complexes (Cu and Hg complexes) that form when the ore is in contact with the leaching reagents, and the related effects on stability of the gold complex is limited. The main changes in the gold complex chemistry and stability in the calcium thiosulfate system as compared to the ammonium and sodium equivalents, as well as related effects on gold recoveries, were investigated in the presence of different types of double refractory ores. INTRODUCTION Barrick has developed a thiosulfate leaching process to treat double refractory gold ores, by combining the use of acidic and alkaline autoclave pre-treatment with thiosulfate resin-in-leach (RIL). The process currently in operation at the Goldstrike mine (the TCM process), uses calcium thiosulfate as the leaching reagent, resin for gold recovery with sulfite/trithionate elution and reverse osmosis as a mean of reagent recycle. The main feed to the process plant is highly preg-robbing sulfidic ore from Goldstrike’s open pit. Prior to feeding the pressure oxidation circuit, the ore is processed through the crushing and grinding circuits and treated in preparation for acid or alkaline autoclave processing (POX)."

Jan 1, 2018

In this study, the effect of different regrinding conditions on the depression of fine pyrite at the cleaner stage was investigated. The regrinding condition was manipulated by different grinding media (stainless steel and mild steel). It was found that, after regrinding with mild steel grinding media, the flotation recovery of pyrite is much lower than with stainless steel grinding media, and it is more difficult to restore by adding more collector. This means, regrinding with mild steel grinding media may depress the pyrite flotation more strongly. The copper activation of pyrite during regrinding was also studied. It was found, that the mild steel grinding media is more beneficial to copper activation than stainless steel media. Additionally, the analysis of pyrite recovery based on the particle size indicated, that the fine particles are more susceptible to different grinding environments than intermediate and coarse particles and therefore are more easily depressed with a much lower flotation recovery.

Sep 1, 2012

By Tim Suljada, Mary Stewart, Jim G. Petrie, Damien Giurco

"The minerals industry is being challenged to reduce the amount of virgin ore that is mined, and to replace this material through the recycling of used commodity items and scrap, or by the reprocessing of waste materials. It is argued here that the existing technology base of minerals processing and refining offers real potential for handling these secondary resources. The challenge is to develop tools by which the most preferable recycling routes (both economically and environmentally) can be identified from a list of feasible alternatives, taking into account any operational constraints of these technologies.This paper describes an heuristic approach to developing the family of all technically feasible flowsheets to address this challenge, from which a preferred option may be selected according to a set of decision criteria (economic and environmental). Our approach uses conventional flowsheeting techniques of selecting flow variables and splitter functions, supported by design performance information for each unit operation. This set of design decision variables is augmented by knowledge of the suitability of a particular waste or scrap stream for a given unit operation within a flowsheet. We achieve this by comparing the composition of the scrap stream with the range of mineral streams for which the unit operation was designed initially. This is inspired by the “overlap” approach proposed by Legarth, where an “overlap” of 1 would suggest that there is high degree of compatibility between a given secondary resource stream and a primary mineral stream as inputs to a specific technology. The “overlap” concept has been extended to include information about the physical characteristics of secondary resource streams, as well as information relating to synergistic / antagonistic influences of minor elements present in the waste stream. A flowsheet which delivers a product of acceptable quality from a given secondary resource material is built up from a progression of unit technologies. The exercise is repeated to generate the family of all feasible flowsheets from combinations of acceptable unit technologies."

Jan 1, 2003

By Vladimir S. Zharov, Vyacheslav A. Tsukerman

"Conceptual imitative dynamic model of developing enterprises for medium and long-term period permitting to ensure coordination of interests of the enterprise and territorial environmental authorities has been developed to enable the process of the prognostication and management of a concentrating mill development, in which a symbol language and terminology familiar to the manager of the company are applied. An algorithm of practical application of this model of company development was elaborated as well as a general methodological approach to the prognostication of the development and procedures of its implementation. The general methodological approach to the implementation of the model has been defined. Within the framework of system approach, a concentrating mill is considered as a subsystem of an ore mining and processing company or a mining and smelting one. A concentrating technology is considered in dynamics, its change is determined by the task of making the company operation profitable. Technological indicators are secondary relative to financial and economical indexes. At the same time, technological and economical indexes are determined in their interrelation with ecological parameters. The elaborated model allows us to estimate all necessary economic, financial and technological indexes in their interrelation both for the company as a whole and as separately redistributed estimating the basic prognostication documents - accounting balance-sheet, profit and loss report, as well as the funds flow statement. When varying the managing parameters, all necessary result-producing financial and economical indexes are estimated and a need in and a possibility of an external funding by various sources are considered.The implementation of the model enables one to determine the required scale of production capacity, as well as the amount of raw-material resources needed. In case of shortages of the latter, there should be considered various scenarios of the production capacity enhancement or the possibility of commissioning of new sites or deposits and introduction of improved technologies."

Jan 1, 2003

By Jaime Sepúlveda

"A broad diversity of critical operating conditions may influence, in very convoluted ways, the actual performance of any given mineral processing system, to the extent that it becomes nearly impossible to empirically determine the independent, decoupled impact of each condition. An effective approach to better understand the behaviour of such complex systems is via the extensive use of sufficiently detailed and reliable mathematical models, allowing the process analyst to explore and learn about the independent effect of all relevant operational conditions. Certainly, these tasks are greatly facilitated if the appropriate software tools - such as the Moly-Cop Tools software package - are readily available. Moly-Cop Tools 3.0 is a set of 63 easy-to-use EXCEL spreadsheets designed to help process engineers characterize and evaluate the operating efficiency of any given grinding circuit, following standardized methodologies and widely accepted evaluation criteria. Moly-Cop Tools 3.0 covers conventional and semiautogenous mills, crushers, HPGR’s, rod mills and vertimills, with the corresponding mass balance and parameter estimation routines; plus complementary spreadsheets regarding Bond’s Law calculations, grinding media selection and performance evaluations and other useful utility functions. As a relevant example of application, specifically focusing on semiautogenous grinding operations, the current publication describes how the models can help us learn and rationalise critical empirical observations such as the relationship between feed particle size and optimal ball filling, the role of the rocks as autogenous grinding media as well as the impact of feed size and discharge grate opening on the mill grinding capacity. Over the last 20 years, Moly-Cop Tools has gained wide acceptance around the mineral processing community in recognition to the quality of the mathematical models contained, their simplicity of application and ease of sharing of the calculations amongst all interested parties, since it is available free-of-charge with no restrictions to make as many copies as needed."

Jan 1, 2014

By Y. H. Tang, H. Y. Zhang

"Tailings from lead-zinc mine contain plenty of dolomite and low-grade fine-grained barite, which is difficult to enrich by mineral processing. Since the density of barite and dolomite has some differences due to the fine dissemination size in a complex sedimentary, the gravity separation tests were conducted with no results obtained. The magnetic separation was conducted to remove the magnetic gangues, and the results were not satisfactory because of the gangue minerals such as limonite and others were low in content. The results of floatation tests showed that the mineral separation of barite and dolomite is quite difficult because that they have similar mineral floatability. Experimental research shows that the good results can be obtained by “desulfurizationbarite floatation” processing with the new depressant TS. The barite concentrate containing BaSO4 91.27%, BaSO4recovery is 70.25% when sodium dodecyl sulfonate serves as a collector and TS as the depressant.INTRODUCTIONBarite is an important mineral material. Often associated with other minerals, it usually needs to be separated by mineral processing in order to meet the application requirements. The main barite beneficiation methods include hand sorting, gravity separation, floatation, magnetic separation, acid leaching, etc. Usually barite associated with oxide ore such as fluorite dolomite, quartz ore etc. are also associated with sulfide ore such as pyrite, sphalerite and galena. The separation between barite and sulfide ore (such as pyrite) is easy. On the other hand, the separation between barite and oxide ore (such as dolomite and fluorite) is very difficult. There are quite a lot of reports on the separation between barite with fluorite dolomite however the separation between barite and dolomite is seldom discussed.The ore properties are quite complex attributable to mineral assemblage containing a large amounts of dolomite. As the density of barite and dolomite has some differences, gravity separation between them is usually easy. The gravity separation tests were conducted with no results obtained due to the fine dissemination size in a complex sedimentary. The magnetic separation was conducted to remove the magnetic gangues, and the results are not satisfactory as the gangue minerals such as limonite and others were low in content. Due to the fine dissemination and intimate association of minerals, and barite and dolomite contain the same group ions of Ba2+, Ca2+ and Mg2+, the results of flotation tests showed that the mineral separation between barite and dolomite by flotation means problematic. Previous studies have been conducted by several institutions but none to date has come up with a satisfactory process in dealing with the deposit. This may be attributable to: high cost of reagents; unsatisfactory performance. Therefore, the key to the flotation separation of barite and dolomite is the application of selective inhibitors. Based on previous test observations and years of extensive research experience in barite processing technology, with the new depressant TS has selectivity inhibition on dolomite developed and used, good results can be obtained by “desulfurization-barite flotation”, which allows barite in the lead-zinc tailings to a comprehensive recovery."

Jan 1, 2018

By Marina Nicolova, Irena Spasova, Plamen Georgiev, Stoyan Groudev

Different strains of "silicate" bacteria were used to improve the quality of kaolin by different ways of treatment. All strains formed large slimy capsules consisting of exopolysaccharides and were related to different species of the genus Bacillus, mainly to B. circulans and B. mucilaginosus. It was found that even a short contact of some hours of well developed cultures of these bacteria resulted in improvement of the bending strength and the other ceramic properties of the kaolin. The improvement was connected with the action of some secreted microbial metabolites such as soluble heteropolysccharides, monosugars and organic acids. The best results were achieved by continuous cultivation of bacteria in the presence of kaolin with a high relative humidity and subjected to periodic stirring.

Jan 1, 2014

By Stephen Gay, Dewetia Latti

"When improving a plant a mineral processing engineer would like to know the mineral composition distribution. In order to assess this distribution in particles, as compared to the corresponding distribution in particle sections, a procedure needs to be applied to the observed particle sections. Such a procedure is called a stereological correction. There exists many stereological correction procedures, but one group of such procedures is based on using those stereological equations that do not require making assumptions regarding particle shape or texture.In particular Davy derived an equation to estimate the covariance of mineral composition distributions for particles from both particle sections and linear intercepts. Furthermore, this covariance can also be used to measure the variance of the composition distribution of each mineral.This paper shall present results verifying this equation. The experimental method was based on obtaining particle information from serially-sectioned particles. Particle samples selected for serial sectioning displayed a range of natural textures including liberated, binary and composite particles. The exposed surface of the polished sections were analysed using QEM*SEM. This procedure was repeated until all of the grains have been polished away. The covariance of mineral distributions were calculated from the serial sections and compared with that calculated using Davy’s equation."

Jan 1, 2003

By F. Xie

Low gold and silver leaching kinetics has been commonly observed in traditional gold-silver cyanidation process, especially in those heap-leaching operations. The reactivity and availability of oxidant was believed to be the critical limitation for gold and silver dissolution. The occurrence of silver sulfide such as acanthite (Ag2S) in the ore may also result in low overall silver extraction. Leaching of gold and silver sulfide in the ferricyanide-cyanide solution has been investigated through rotating disc tests and the assistant effect of ferricyanide on increasing the dissolution rate of gold and silver was noticed. The potential use of ferricyanide as an auxiliary oxidant in gold/silver cyanidation process was proposed based on the results of leaching of gold-silver ores.

Jan 1, 2014

By A. J. Lynch, L. Ergun, M. Oner

"A research program on modelling cement grinding circuits has been in operation at Hacettepe University, Ankara, for four years. It has concentrated so far on tube mill and air separator grinding circuits for cement clinker, with emphasis on plant sampling surveys, including axial sampling inside the tube mills. The data used for model development have come from 33 surveys in 9 plants.The operating conditions have been:- mill sizes - 3.2 to 4.8 metres diameter and 8.5 to 15 metres long,- mill feed rates - 46 to 158 tonnes per hour,- air flow through mills - 25000 to 125000 cubic metres per hour,- cement clinker work indexes - 10.3 to 18,- separator sizes - 2. to 3.1 metres diameter,- separator feed rates - 132 to 689 tonnes per hour,- separator speeds - 12.3 to 21 metres per second.The ball mill model is Whiten’s perfect mixing model and the separator model is the Tromp curve with a fish-hook. This paper emphasises the importance of calculating the breakage rates and the discharge functions with three case studies at five different circuits which were selected for discussion because they show how particular features of circuit operation can be included in the general models. Size distribution graphs are used to illustrate every aspect of the discussion"

Jan 1, 2003