Search Documents

By G. M. Dunn

Pressure leach autoclave circuits are employed in the leaching of ores, concentrates, mattes, alloys and intermediates for the recovery of metals into solution. Once the metals are extracted into solution the value metals can be recovered by hydrometallurgical means such as by purification followed by electrowinning, hydrogen reduction, pyrohydrolysis, crystallisation and other unit operations. In many of these integrated flowsheets the pressure leach step is pivotal to the recovery of the value metals from the host material. In an expansion or a new project, a large component of the capital cost can be associated with the pressure leach step and process engineers frequently look for opportunities to mitigate costs. This paper examines a new route for increasing the capacity of an exothermic pressure oxidation leach for sulphide concentrates, sulphide and phosphide mattes and alloys.

Jan 1, 2004

By George Delorme

"AbstractThe basic intention of this paper is to present, from a practical viewpoint, a thorough outline of all the sound and accepted principles connected with attaining satisfactory rope performance from multi-rope friction winders.In order to emphasize the importance of some aspects of rope maintenance, a limited amount of hoist rope theory has been included, a s it is felt that without this, some of the more critical, but nevertheless practical, aspects would perhaps pass without full appreciation of their individual merit.It is very much appreciated that many of the maintenance topics and practices discussed herein are already being observed with a high degree of skill among those already involved in modern friction winding. The hope is expressed, however, that the paper will be of additional assistance, and of particular help in introducing sound maintenance principles to those who are moving into this field of operation for the first time.Hoist RopesWITH a multi-rope friction winder system, structural upset within the hoist rope's cross section can occur if the ropes slip in the drum treads. This upset will usually appear at either end of the rope at the tangent point of the drum or deflection sheave with the respective conveyance in the normal uppermost position. This slipping action on the drum causes the outer cover of a Full Locked Coil or the strands of a stranded rope to shift, leading to structural upset. The result very often means that the ropes have to be withdrawn from service before completing their maximum service potential.The cause of any rope slipping in its tread can be associated with a discrepancy in tension of that rope between one side of the drum and the other."

Jan 1, 1977

By H. Marquis

The present paper consists of a survey of the literature on the problems of abrasion and wear of metals and materials by suspended matter. This problem is a very general one in industry, and is especially notice-able in the operation of cyclones and other types of dust collectors. The problem of abrasive dust in corrosive gas environments, such as commonly encountered in metallurgical industries, is particularly severe. Very little work has been done in the study of this type of abrasive wear, especially at high temperatures. However, a general review is presented here of all the work published on related subjects, such as that involving sand erosion in turbines and water wheels and the effect of temperature on friction wear. Topics in this paper include: blasting wear by sand, quartz, limestone, silicon carbide and other refractory particles; methods of investigation; effects of velocity, temperature and *Canadian Armament Research and Development Establishment, Valcarter, P.Q. angle of attack; correlation between indentation hardness, scratch hard-ness and resistance to abrasion; the effect of protective coatings; resistance of various metals; etc.

Jan 1, 1962

By Charles Amoah

Abosso Goldfields Limited has been optimizing the comminution circuit at the Damang Mine Operation for the treatment of 100% primary ore. The optimization process started at a base rate of 343 tph when treating primary crushed primary ore, and was increased to above 600 tph with partially crushed primary ore. Abosso Goldfields engaged Orway Mineral Consultants (OMC) to assist with the optimization process in 2009 and the two companies have been working together since, to further refine the process. Continuous improvement was achieved through crushing circuit modifications, changes in operating processes and grinding control system utilization. This paper discusses the improvements developed for the increase in milling capacity and improvements in final product size.

Jan 1, 2012

By G. M. Mason

History Due to its strong affinity for oxygen, aluminium as an element was isolated only after many other rarer metals had been prepared and studied. It was just over one hundred years ago that two scientists, Hans Christian Oersted and Friedrich Wohler, produced the first few pellets of aluminium and determined its physical properties. These early investigators used metallic potassium as a reducing agent. Later, St. Claire Deville, by using sodium instead of potassium, improved the yield in the reduction and produced some pounds of aluminium. From a figure of about $110 per pound in 1855, the price had fallen to about $4 per pound by 1886. In that year, a very important discovery was made independently by Charles Martin Hall in Oberlin , Ohio, and Paul . Heroult in France. Stated in its simplest terms, the discovery of Hall and Heroult was that aluminium could be produced by electrolyzing a solution of the oxide in molten cryolite. The application of the Hall-Heroult process made the metal immediately available in commercial quantities and, by 1900, the price had fallen to 23 cents per pound. The growth of the industry in the past fifty years is well known, and is outside the scope of this paper. It is, perhaps, not generally known that aluminium was first produced in Canada at Shawinigan Falls in 1901. Since that time, production has been continuous at one or more smelters in the Province of Quebec. The largest of these smelters, which is also the largest aluminium smelter in the world, is at Arvida, Quebec, on the Saguenay river. A large power potential and access to ocean shipping were the two principal reasons for the establishment of aluminium production facilities in the Saguenay district. It is interesting to note that the aluminium industry, as a large user of power, took an active part in the early industrial development at Niagara Falls and Shawinigan Falls, and is now repeating the process in the Saguenay valley.

Jan 1, 1949

By A. Brown

THIS P APER has been pre-pared as a progress report on Mines Branch investigations into problems of ground stress in certain co al mines of Western Canada. As such, it should be considered as a companion report to the one ( 1) presented to the Mining Society of Nova Scotia in 1956 and which dealt with similar investigations in the coal mines of Eastern Canada. For the past 50 years, dynamic incidents in the form of 'bumps' and 'outbursts' have been occurring in the coal mines of the Inner Foot-hills belt of tl1e Canadian Cordillera. As these phenomena generally become more frequent with in-creased thickness of overburden, a limiting depth of mining of 2,500 feet has been set (2) for estimating recoverable reserves of coal. If such a view were accepted, from a long-term viewpoint very large resources of coking-grade ?coal -in a part of the continent deficient in such coals -would not be available to the nation. The terrain in which these in-6dents take place may be described in geological terms as being dominated by pronounced structure in strata ?consisting of a large proportion of highly indurated rocks. The Geological Survey of Canada has co-operated by carrying out structural studies (3) at the mines, supplemented lithological by stratigraphic observations.

Jan 1, 1958

By K. Heid

"Although concentrated efforts have been made to deplete PCB transformers from the Canadian environment, numerous transformers (as well as ballasts, capacitors and magnets) continue to exist throughout the Canadian mining industry. The existing installed base is slowly being phased out as environmental issues come under increasingly high profile. The following article identifies the potential problems of owning PCB transformers and offers some solutions for their removal, disposal and replacement. IntroductionPolychlorinated Biphenyls (PCB) are synthetic chemical compounds consisting of chlorine, carbon and hydrogen. PCB was widely used in transformers due to its physical properties, including stability, low flammability and non-conductivity. Use of PCB in electrical equipment has been banned since 1977 when the extent of environmental contamination was discovered.Although PCB’s have been outlawed for use in electrical equipment since the late 1970s, safe storage regulations were not addressed until 1988 when a major spill prompted the federal government eventually to issue the storage of PCB Material Regulations in 1992. These regulations replaced the Interim order of 1988 under the Canadian Environmental Protection Act.PCB transformers are usually referred to as askarel filled transformers or as PCB contaminated mineral oil transformers. Askeral transformers were designed to contain high concentration PCB fluids, referred to as askarel. Mineral oil transformers were not designed to have PCB concentrations but were inadvertently contaminated during manufacture or maintenance activities."

Jan 1, 1998

By L. F. Haven

"The desirable shovel speed-torque curves are described, along with the characteristics of the more important electrical components used to approximate these curves. A particular shovel regulator system combining these components is discussed in detail and some of the advantages and disadvantages of the system are given.INTRODUCTIONIN 1959, STATIC CONTROL was for the first time successfully applied, installed and operated on a mining machine in North America. Since that time, a great deal has been learned about this control by the people maintaining these machines as well as by the de-signers.In 1961, the first SCR (Silicon Controlled Rectifier) or thyristor control system was installed on an excavator. This control differed from the earlier static control in that thyristor excitors supplied the generator fields directly. The development of thyristors of a sufficient rating to supply amounts of phase-controlled power to the generator fields eliminated the bulky Mag. Amp. -Rectifier combination previously used."

Jan 1, 1969

By N. W. Xu, M. D. Wei, F. Dai, B. Li

"Chevron notched samples achieve general acceptance for measuring the Mode-I (opening mode) fracture toughness of rocks. The cracked chevron notched semi-circular bending (CCNSCB) sample, which is developed from the International Society of Rock Mechanics suggested the cracked chevron notched Brazilian disc method, has recently received much attention. However, these chevron notched methods have not been fully mastered, some ideal assumptions based by their theories and formulas, such as the straight-through crack assumption (STCA), have not been verified detailedly. Fractures of CCNSCB specimens were numerically simulated considering different heterogeneities, geometrical and mechanical parameters. The results show that, the real fractures of CCNSCB specimens are never satisfied with the STCA. In fact, micro fractures not only occur in the notch tip but also the two chevron edges. Consequently, the crack front features prominently in a shape of parabolic curve, far from being straightthrough. Moreover, curvature of the crack front is only affected by shape of the chevron ligament. Cracks usually start from two sides of the notch tips rather than center of the notch width, and propagate deviating from the postulated fracture routes. These fracture mechanisms induce errors with the measurements, and thus more attentions should be paid to the real fractures of the chevron notched samples for measuring fracture toughness more accurately. INTRODUCTIONWith the increasing requirement of people for resources and energies, frequent rock engineering activities have been conducting, such as underground excavation, oil exploration and deep burial of nuclear waste. Many problems appear in rock fracture. Consequently, there are more and more attentions paid in rock fracture mechanics due to its broad application prospects for solving these engineering problems. Since Mode-I (opening mode) fracture is the most common failure mode in rocks, Mode-I fracture toughness is a primary parameter to predict rock mechanical properties in actual engineering, and thus its accurate values are necessary to the researches of rockburst, rock mass slope stability, rock cutting, hydraulic fracturing, tunneling, et al. Therefore, it is thus significant to evaluate and study relevant methods to obtain the reliable value."

Jan 1, 2015

By Fabio Terzi

In this investigation some preliminary results are reported about the electrochemical oxidation of CO using goldbased encapsulated nanoparticles grafted on conducting substrate. The investigation has been planned in four steps: 1. production of Au(111) substrate and modification with self assembled monolayers; 2. synthesis and embedding of nanoparticles; 3. grafting of encapsulated nanoparticles on electrode substrates; 4. investigation of CO electroxidation on the modified electrode. The systems were characterized by means of various techniques (spectroscopic, microscopic, and electrochemical methods), obtaining information about SAM's structure and morphology, size and composition of nanoparticles and electrochemical behavior of modified electrodes.

Oct 1, 2003

By J. D. Wilkins

"Ore outcrops were first discovered in the area in 1911. Following various periods of exploration by private interests and Cominco Limited, the Coast Copper Company, Limited property was brought into production in August 1962. Subsequently, Cominco explored the adjacent Quatsino Gold Mines property and is currently developing, and producing from, what is now known as the Benson Lake Mine.The Benson Lake Mine was developed using a conveyor-equipped decline and trackless LHD equipment. The operation produces 800 tons per day of copper-iron ore, copper being the main product. Copper and iron concentrates are trucked 25 miles to storage and shiploading facilities near Port McNeill to await shipment to Japan."

Jan 1, 1971

By R. J. Mitchell

"A lest apparatus has been developed for obtaining the relations among confining stress, porosity and percolation rate for hydraulic sand backfills. The apparatus can also be used to evaluate internal drainage characteristics and the effects of partial saturation on percolation rates. The test apparatus, test procedures and typical test data are presented in this paper.IntroductionAlthough the standard percolation test has become an accepted method of evaluating the drainage characteristics of hydraulically placed tailings backfill, it is recognized that the test results require considerable interpretation due to the following factors: (I) The results can be markedly influenced by varying sample preparation procedures, which vary the amount of material segregation in the sample . In particular, a thin layer of slimes on the top of a sample can control the flow of water into the sample. Wall edge effects can also affect the test results. (2) The in-place porosity of the backfill is not duplicated in the test sample and empirical formulae must be used to estimate the variation of percolation rate with porosity. (3) Internal drainage characteristics and the percolation rate of partly saturated fill cannot be evaluated in the standard percolation test.In addition to eliminating these problems, the compression percolation test apparatus also provides additional data on the mechanical properties of the backfill. Compressibility (or bulk modulus) is measured at different stress levels during the course of a test and this information can be used in evaluating the usefulness of the fill in providing ground control and in limiting ground subsidence. The engineering design of mine backfill is becoming an important part of the over all design of underground mine operations. The design problems are sufficently different from conventional civil engineering soil mechanics problems that new test methods and design procedures are required."

Jan 1, 1981

By Eric Poulin, Anthony Clapperton, Jocelyn Bouchard, Jaime Cristobal Rojas-Montes, Benjamin Legare

"Several grinding mill dynamic simulators have been developed in the last half-century. However, complete circuit simulations are mainly limited to academic investigations, and on-site applications for advanced control or real-time optimization are scarce. One particular issue that has certainly curbed a more widespread use is the time and efforts required for model calibration. This paper illustrates this challenge and presents a calibration method based on dynamic simulation using industrial data and laboratory testwork. The simulator models discussed originate from the work of Austin and Luckie (1972) for grinding mills, and Plitt (1976) for hydrocyclones. A two-stage approach based on a least squares minimization allows determining calibration parameters values. Firstly, laboratory testwork are required for characterizing breakage coefficients of the ore. Secondly, step change responses and their simulation— effect of ore and water feed rates on output flow rates and size distributions—allows identifying transport/mixing conditions. Simulation results are in agreement with actual process responses to variations of feed conditions obtained from a plant survey.INTRODUCTIONDynamic models for grinding circuits has been intensively studied since the 1970's notably by Austin and Luckie (1972b), Klimpel and Austin (1984), Rogovin and Hogg (1988), Napier-Munn et al. (1996), Liu and Spencer (2004), and King (2012) among others. The resulting models primarily serve in simulation applications for process equipment sizing, which incidentally also helps developing a better understanding of comminution operations. An obstacle curbing a more widespread and targeted use of grinding simulation for process control and optimization purposes is the time and efforts required for dynamic model calibration. It remains a cumbersome task that is typically not well detailed in technical papers. This could explain why dynamic process simulators are mainly confined to academic applications."

Jan 1, 2016

By S. H. Ash

Introduction Probably the newest thing in mining safety is the apparent dissatisfaction on the part of the mineral industry, as represented by both management and labour, and the general public of many nations in which mining is conducted, with the safety record of the mining industry. This is reflected by published comments in the technical press;' in labour periodicals, in popular Journals and periodicals, and in the daily press (5, 11). Despite what may be said to the contrary, mining in the United States is becoming safer, and this trend has been evident for several years (see Figures 1 to 4). Because the author's experience has been mostly in the United States this paper will discuss briefly some recent observations in the United States that have a bearing on mining safety. Because coal mining is of primary interest to the Mining Society of Nova Scotia, the paper treats mostly of coal-mining safety; however, many hazards in mining .are common to all mines, regardless of the minerals mined.

Jan 1, 1950

By Dave M. Jakelski, Gerhard W. Heinrich, Peter F. Wells, Daniel F. Suarez, Jamie B. Beauchamp

"A need for increased copper concentrate production and for less nickel contamination in that concentrate at Falconbridge's Strathcona Concentrator during 1993 required the installation of a third flotation column and improvements in the operation of the existing circuit. Innovations in wash water distributor and launder design were fundamental in achieving objectives on a new 3 meter diameter column. Minnovex plug-type spargers were tested on a 2.1 meter diameter column in order to reduce maintenance requirements. The paper details the measures taken to enhance column flotation circuit performance and the results obtained.IntroductionFalconbridge's Strathcona Mill receives 10% of the ore feed from a rich copper zone in the Strathcona mine. This ore typically grades 7% copper and 1 % nickel and, because of its high copper content, it is processed in a separate circuit ('C' circuit) which consists of conventional grinding, rougher flotation with the concentrate being treated with lime to pH 12.3 and cyanide followed by column flotation. The columns are operated with mechanical flotation scavengers and the scavenger concentrate is returned to the column feed. Testwork conducted in 1991 showed that the original flotation column (Column 2) could only produce 5.5 mtph of concentrate with less than 0.5% nickel (Figure 1).Between 1991 and spring of 1993, production was increased at times by open circuiting the scavengers. Metallurgical improvements were obtained by improving the wash water distributor of Column 2 and by wash water sprays in conventional cells (1 ). However, the scavenger concentrate assayed 0. 7 -0.8% nickel and was not acceptable for long term operation. When Copper ore production targets were significantly increased for 1993, it became clear that an additional flotation column was required. The new flowsheet employs mechanical scavenger cells on the column tails as in Column 2 circuit (Figure 2). A -parallel configuration was chosen as pulp solids fraction has been shown to be a critical variable and the second column in series would receive a lower density feed."

Jan 1, 1994

The dynamic breakage process of rocks by the impact of a hydraulic hammer is more complex than one normally assumes. It is even more difficult when one has to conduct the breakage under water. In such cases one does not know exactly what the surface topography and composition are at the bottom of the sea or river and, hence, it is more difficult to select the best position of the hammer before starting the hammering. Typically, an industrial hammer has a diameter of about 250 mm, a length of about 1.25 to 1.75 m and a mass of several tons. The hammer frequency can be up to 50 impacts per minute. The general principles of rock hammering can be easily summarized, but this knowledge is not sufficient to adapt adequately the method for less common rock conditions (e.g. less brittle rock, presence of vertical and subvertical fractures, etc.). That is the reason why we initiated a research project, whereby a scale model has been developed to conduct experiments in the laboratory and whereby discrete element simulations are being conducted. Both aim at a better understanding of the basic mechanisms of rock hammering. The scaled experimental model allows varying the impact energy and the static weight independently. Within the experiment, the hammer is in contact with the rock specimen under a certain confining pressure and with a certain contact pressure due to the static weight. A weight falls on the hammer, creating the dynamic action or impact; the height over which the weight falls can be varied. The penetration is recorded after each impact. After a certain penetration the test is stopped and the internal crack patterns are described. Some simulations have been conducted, allowing the modeling of individual fracture initiation and growth during the penetration of the hammer by either a constant displacement rate (using the UDEC-code) or by introducing the dynamic process (using the PFC-code). Some of the observed features in the laboratory experiments can be visualized in the simulations. However, further research is needed to allow the simulations being an adequate tool to well understand the dynamic process in laboratory experiments, as well as the in-situ behavior.

Aug 1, 2013

By Kathy S. Kalenchuk

Damages have been observed in shafts, backfill infrastructure and the slick line at the Leeville Mine. Shaft damage (shearing and spalling of the concrete liner) is attributed to mine-induced rock mass deformations concentrated where regional faults intersect the shafts. Aggregate bin, mixer station and conveyor drive damage (shotcrete shearing, heave of concrete floor slabs and bending of a vertical steel beams) is attributed to rock mass squeezing induced by elevated magnitudes of the vertically orientated major principal stresses. Separation of the slick line has occurred do to extension of the stressshadowed rock mass immediately above the mined out areas. Three-dimensional numerical models have been developed and calibrated to simulated rock mass deformations with magnitudes similar to those believed to have produced the observed damages. By stepping through the mine sequence, models reproduce deformations at the same mining stage as when damage has occurred. Calibrated models have been used to forward project further damage over the remaining mine life.

Jun 1, 2012

By A. P. Paiva

The solvent extraction properties exhibited by some /V,N'-tetrasubstituted malonamides to efficiently and selectively recover iron(III) from concentrated chloride leaching solutions can be found in the recent literature. The iron(III) extractive chemistry exhibited by some of these derivatives is revisited, in order to compare their chemistry with that shown by a few of the new malonamide compounds. The generally good extraction efficiency towards Fe(III), from >4 M hydrochloric acid solutions, and the relative ease of Fe(III) stripping by distilled water are remarkable findings that are confirmed for the malonamide derivatives described in this work. Furthermore, additional data regarding their selectivity towards Fe(III) extraction over several base metal ions and their behavior when subjected to successive Fe(III) extraction-stripping tests are also presented and discussed.

Jan 1, 2006

By Stanley W. Holmes

"The discovery of extensive uranium mineralization on the Pronto property in April 1953 initiated a program of staking, exploration, and development unparalleled in Canadian mining history. Within twelve months of the discovery hole, sufficient ore had been blocked out to merit a 55-million-dollar contract with Eldorado Mining & Refining Co. On October 15, 1955, two years and four months after discovery, Pronto went into production with a mill rated at 1,000 to 1,500 tons per day. The property is on the southern edge of the Algoma uranium district, 10 miles east of the town of Blind River and close to the Canadian Pacific Railway and Highway 17. Docking facilities for Great Lakes steamers are avail-able at Spragge, 4 miles to the east.The data and conclusions presented in this paper are based on field studies, drill hole information, and underground development. The ideas of ore genesis are those of the writer, and will undoubtedly be modified as more detailed studies and research are carried out. Because of security regulations, information pertaining to grade and tonnage will not be discussed.GeologyThe general geology of the Algoma basin has been outlined in a pre-ceding paper (Joubin and James). The description below is concerned essentially with the rocks most closely associated with the Pronto deposit. They may be grouped in three structural and lithological units: (1) the pre-Huronian basement, (2) the Mississagi formation, the lowest member of the Huronian sediments lying unconformably on the basement, and (3) a series of basic intrusives cutting (I) and (2). Most of the uranium mineralization occurs in a quartz-pebble conglomerate forming the basal member of the Mississagi quartzite."

Jan 1, 1949

By H. J. McQueen

Aluminum was hot worked at 400 - 500°C and strain rates (e ) of 0.004 -0.1s-1, under reversing strains (c) of 0.5 to 0.2 or 0.5 to 0 and also advancing from 0.5 to 1 or 0.5 to 5. Under similar test conditions for different parts of the strain paths, the average measured flow stresses are found to agree with each other. In the forward and backward strain path tests, the almost identical steady state plateaus affirm the occurrence of dynamic recovery (DRV). On reversal of strain direction at constant e , there was generally negligible Bauschinger effect. In specimens annealed at 400°C, static recrystallisation (SRX) was followed microstructurally. mainly by disappearance of elongated grains with serrated boundaries because the new grains were only little a finer than the old due to low strain energy. The only influence of reversing strain path observed was the effect of change of grain boundary area as grains elongated or returned towards equiaxed. In optical microscopy, elongated grains with serrations and deformation bands confirmed DRV in forward path specimens. In reverse path specimens, equiaxed grains were gradually restored with retention of serrations and bands. In low magnification polarized optical microscopy, grain alignment increased with strain for forward path specimens; whereas it decreased in reverse path ones, supporting DRV. Orientation imaging microscopy (OIM/SEM) revealed that elongated grains are broken up as deformation bands rotate during the forward path and that grains return to equiaxed appearance on backward straining. Comparative studies using optical microscopy in polarized light (POM), OIM/SEM and transmission electron microscopy (TEM) revealed that while subgrains remain equiaxed and constant in size and character during the forward and backward paths, the fraction of low angle facets decreased while that of high angle grain facets increased with increasing strain; these are coupled with a fairly low fraction of medium angle boundaries. The results contribute to the understanding that dynamic recovery in aluminum maintains sub-boundaries with low misorientation but as grains elongate and more subgrain become adjacent to grain boundaries the fraction of high angle boundaries rises (with backward straining it was vice versa).

Jan 1, 2007