Search Documents

By A. W. Stradling, M. J. Fairweather

"The selective flotation of lead, zinc and iron sulphide minerals is key to the economic performance of concentrators treating zinc-lead ores. Diagnostic metallurgy is a tool to quantify mineral behaviour as a function of particle size and liberation. The result of such analysis may be used to select preferred strategies to improve metallurgical performance. The zinc flotation circuits at three Teck Cominco operations: Sullivan, Polaris and Red Dog are compared here. This paper analyses operating data from each of these circuits. The effects of mineralogy and performance by particle size are emphasized. Metallurgical performance at these three concentrators varies substantially. Liberation size is the major factor in determining metallurgical performance. Complex mineralogy requires a fine grind to achieve effective liberation. Fine grinding results in offsetting decreases in concentrate grade through entrainment. The economic treatment of complex fine-grained deposits requires optimisation of regrind size for liberation without unduly compromising concentrate grade through gangue entrainment.INTRODUCTIONUntil recently Teck Cominco Metals Ltd. operated three mines treating zinc-lead ore. In order of increasing mineralogical complexity they are: the Polaris Mine on Little Cornwallis Island in Nunavut in the eastern Arctic, the Sullivan Mine in southeastern British Columbia and the Red Dog Mine in northwestern Alaska. Both the Polaris and Sullivan Mines have recently ceased to operate due to depletion of ore reserves.The ore type and associated gangue, mineralogy and iron solid solution vary significantly between these deposits. Table 1 summarizes some of the important differences"

Jan 1, 2003

By A. Banerjee, J. P. Weiler, J. Jekl, J. T. Wood, R. Berkmortel

"The work presented here is part of an ongoing project designed to develop predictive capabilities of the local mechanical properties, and thus, structural behaviour of a thin-walled high-pressure die-cast AM60B magnesium alloy component. This work focuses on developing correlations between process parameters and local microstructure. Numerical simulations of the die filling and solidification behaviour of the AM60B component were used to estimate local process parameters such as solidification rate, temperature gradient, filling velocity, etc. These estimated parameters were used to establish semiempirical correlations with measured VALUES (of the local microstructure measured in regions throughout the component of different solidification conditions. INTRODUCTIONHigh-pressure die-cast magnesium alloys are experiencing increasing use in structural automotive components. A strength-to-weight ratio comparable to steels and its ease of castability allow for these alloys to be utilized in such capacities as instrument panel beams, seat and door frames, and engine cradles, among others (Gjestland and Westengen, 2007). However, the current use of these alloys is limited due to variations in local mechanical properties. These local property variations restrict part designers to assume lower than actual properties, resulting in larger sections, thus diminishing the light-weighting advantages of magnesium alloys. If these local property variations could be predicted, part designers would be able to optimize die-cast magnesium alloy components and fully take advantage of the light-weighting capacity of these materials.The work presented here is part of an ongoing project aimed at developing predictive capabilities of the local mechanical properties, and bulk mechanical performance, from variations in local microstructure, and ultimately from local process parameters in die-cast magnesium alloys. This project, unique in its nature, is based upon the results determined from fifty sequentially cast AM60B magnesium alloy instrument panel beams provided by Meridian Lightweight Technologies (shown in Figure 1)."

Jan 1, 2012

By Riggin P. R.

"IntroductionIndustrial Relations combines two very important relationships - employee relations and union relations.Employee relations always come into play when people are hired to perform tasks. Because mineral processing plants cannot be operated successfully without people, at least not yet, if they ever will be, employee relations must exist in an operatingplant.If the employees choose to be represented by a union, then a relationship with the union as an institution also comes into play. It is very important to note that unionization does not mean that the employee relationship is replaced by a relationship with the union. The latter is superimposed on the former, but it does not replace it. Similarities and overlaps in the two relationships will be present, some of which are of fundamental importance. Nevertheless, they are two different relationships and the reader should bear this in mind when reviewing those parts of this chapter which discuss unionization, collective bargaining, collective agreements, and work stoppages.These two important relationships, which we have chosen to combine and call industrial relations, have crucial roles to play in the social system which interrelates people performing the necessary tasks involved in the operation and maintenance of a plant. The technological organization - equipment, process layout and so forth - and this social system are interdependent and complementary. This chapter attempts to show that the potential level of effectiveness of both the technological organization and the social system depends on the recognition and nurturing of this nexus between them.Occupational health and safety and training are subjects for another chapter. But, both of these have been critical and longstanding employee relations topics . They are destined to take on added importance in the future. As issues in collective bargaining, they are also attracting increasing attention in all union relations. It is hoped that the reader will not isolate from industrial relations those topics which are being dealt with in another chapter. They are very much a part of it and we cannot refrain from making some reference to them."

Jan 1, 1989

By J. Dionne

"Next to the actual mine of Les Explorations Muscocho Ltée in Montauban, Quebéc, you could find a total of 364 000 tons of flotation tailings assaying 1.4 Au g/t et 82 g Ag/t to the south of the municipality. This tailings pile is what is left of previous operations. Preliminary leaching tests on these tailings in laboratory columns gave interesting results which led to tests in larger columns in 1984 and to a pilot test on a 750 ton heap in Montauban during the summer of 1985.This paper briefly describes the columns tests performed at the Centre de Recherches minérales and the heap leaching test designed and conducted by SOQUEM in Montauban. It also presents the results obtained.RESUMEPrès de la mine actuelle de Les Explorations Muscocho Ltée à Montauban, Quebéc, se trouvent, au pied du village, 364 000 tonnes de rejets de flottation titrant environ 1,4 g Au/t et 82 g Ag/t. Ce tonnage de rejets représente ce qui reste de l'opération des anciennes mines de Montauban.Des essais préliminaires de lixiviation en colonne sur ces rejets ont donné des résultats encourageants. Ils ont été suivis en 1984 par des essais en colonnes plus volumineuses et par un essai pilote à Montauban en 1985 sur une pile de rejets de 750 tonnes.Ce te x te donne une brève de script ion des essais en colonne effectues au Centre de Recherches minérales et de l’essai pilote planifie et exécute à Montauban par SOQUEM. Il présente les résultats obtenus."

Jan 1, 1987

By A. L. Nunes, J. R. E. Garcia, G. Silva, U. Prasad, C. Rabe

"Drilling through the Guayabal shales, a gray calcareous shale, and the C1 to C100 formations, a well-cemented calcareous-sandstone in Corralillo field, Mexico, is a challenge due to severe wellbore instability problems. Additionally, there has been a history of ineffective reservoir stimulations by hydraulic fracturing. To predict and mitigate these subsurface issues, it is essential to characterize the mechanical properties and rocks strength for a better prediction of borehole stresses and collapse pressure during drilling. Various correlations can be used to estimate and/or determine the unconfined compressive strength but most of them are based on transit time and porosity.In this study, grain size distribution was combined with acoustic travel time, porosity and static Young’s modulus to develop a rock strength prediction model for the turbiditic sandstones of the Chicontepec basin. The main reason this combination of parameters was employed was because of the wide variations in rock strength estimated using traditional porosity-based correlations such as the McNally’s (1987), GMI-Jizba-E’s and Bradford’s (Bradford et al., 1987).To develop a new correlation, a geomechanical and microstructural campaign was initiated. Mineralogy by X-ray diffraction, pore and grain sizes by petrography, clay distribution by SEM and porosity by mercury intrusion porosimetry were measured. Static and dynamic Young’s moduli and Poisson’s ratios were acquired by triaxial and ultrasonic measurements on undisturbed sandstone samples from the Chicontepec basin. More than ten offset wells with wireline data, including transit time, porosity, density, resistivity and gamma ray, were used for reservoir and geomechanical characterizations.Our analyses lead us to propose a new correlation for predicting the uniaxial compressive strength (UCS) of sandstones of the Chicontepec Basin as a function of transit time and grain diameter, both of which can be derived independently from destructive laboratory tests. Our results also highlight the importance and value adding of a combined approach incorporating grain size analysis in the rock strength prediction. The UCS predicted using the transit-time and grain-size-based model presents a median value (P50) of 76 MPa, P10 of 55 MPa and P90 of 89 MPa."

Jan 1, 2015

By Takayuki Takasugi, Naoya Masahashi, Yasuyuki Kaneno, Satoshi Semboshi, Yusuke Kadoi

Cu–Ti alloy wires doped with and without a small amount of Ni were fabricated by over-aging and using intense drawing procedures. For both the Cu–Ti alloys with and without Ni doping, the over- aged microstructure was occupied fully with a coarse lamella of Cu solid solution and β-Cu4Ti plates precipitated discontinuously by grain boundary reactions. The full-lamellar microstructure was developed much more rapidly by aging in multi steps at 873 K to 723 K rather than by isothermal aging at 723 K. Ni doping in Cu-Ti alloy was also effective to accelerate the formation of the lamellar microstructure. When drawing the over-aged alloy with inferior hardness but superior electrical conductivity, the strength increased steadily and eventually exceeded that for the wires drawn from the peak-aged alloy. In addition, the electrical conductivity of the wires drawn from the over-aged alloy was always much greater than that from the peak-aged alloy. Eventually, the procedure of over-aging, followed by intense drawing, could enhance both the strength and electrical conductivity of Cu-Ti alloys, whichever they contain a small amount of Ni or not, rather than the conventional peak-aging and drawing process. INTRODUCTION Cu-based alloy wires, which have an excellent combination of strength and electrical conductivity, have attracted extensive attention for highly mechanically stressed electrical devices, such as conductive lead wires and wires in suspension springs. Cu-Be alloys are widely used for such electrical components owing to their combination of strength and electrical conductivity among industrial Cu-based alloys. However, since beryllium is potentially toxic and also a rare element, substitute materials for Cu-Be alloys have been searched for several decades. Age-hardenable Cu–Ti based alloys have been proposed as candidates because their mechanical and physical properties are comparable to those of Cu-Be alloys; however, their electrical conductivity is inferior (Datta & Soffa, 1976; Soffa & Laughlin, 2004). In order to satisfy the requirement of downsizing and streamlining electrical devices, further improvement of the mechanical and electrical properties of Cu–Ti alloy wires is needed. Age-hardenable Cu–Ti alloys, which contain approximately 3 to 6 at.% Ti, are typically prepared using a solid solution treatment above 1100 K and then aging at a moderate temperature of 700 K to 800 K. It has been revealed that the microstructural events during aging progress as follows (Soffa & Laughlin, 2004): (1) compositional modulation of the parent supersaturated Cu solid solution in an initial aging stage (Laughlin & Cahn, 1975), (2) continuous nucleation and growth of fine needle-shaped precipitates of metastable β’-Cu4Ti with a tetragonal structure in a peak-aged stage, and (3) discontinuous precipitation of cellular components laminating the plates of a terminal Cu solid solution and stable β-Cu4Ti with an orthorhombic structure at the grain boundaries in an over-aging stage. It has been also accepted that the highest number density of dispersed fine β’-Cu4Ti needles should contribute to maximal strengthening. On the other hand, decease of the strength in the over-aging stage occurs due to the replacement of the fine β’- Cu4Ti needles with cellular components containing coarse β-Cu4Ti plates, while the electrical conductivity is significantly enhanced due to the depletion of solute Ti in the Cu matrix. This suggests that a combination of strength and electrical conductivity for age-hardenable Cu-Ti alloys is in a trade-off relationship, and that innovative improvement of both properties might be limited to tuning the aging conditions.

Jan 1, 2019

By B. McHenry, A. E. Wraith, P. J. Mackey

The Wallaroo smelter on the Yorke Peninsula, South Australia commenced smelting operations in 1861 treating ores from the nearby Moonta and Kadina mines. The plant expanded and modernized on several occasions and was a leader in the successful introduction of new technology to improve operations. It operated continuously until 1923 when local mines became exhausted; in the closing stages of the 19th century it was the largest copper smelter in the world outside of those in Swansea, Wales. In 1892 a small electrolytic refinery was established at Wallaroo, the first in Australia, based on principles developed by Elkington at Pembrey, Wales in 1869. The Wallaroo refinery was specifically built to recover gold and silver from copper produced by smelting gold-containing feed materials shipped from Western Australia. This first venture into electrolytic refining was replaced in 1903 by a somewhat larger refinery which, although modest in size for its time, with a capacity of about 1000 tonnes of cathode copper per year, was very productive in precious metals. Anode copper was produced by an updated version of the reverberatory-based Welsh process until 1910 when barrel-type pneumatic converters were introduced based on American practice; subsequently, anodes were cast by tapping the precious-metals rich "bottoms" portion of converter copper as produced at about one-fifth into the copper blow. The present paper describes the Wallaroo refinery, its anode supply and products, supported by initial observations on a sample of a Wallaroo cathode held in the collection of the South Australia Museum, Adelaide SA, Australia. INTRODUCTION Australia ranked 6th in the world for copper mine production in 2018, with an output of 918,000 tonnes of mined copper, after Chile, Peru, Congo, China and the USA; about 40% of Australian mined copper was smelted in the country. Interestingly, the world ranking of Australia in mined copper has, with a few variations, remained about the same for more than 100 years – of interest, it was also the 6th largest country for copper production at 21,089 tonnes in 1899. At that time, all or most of the copper was smelted in the country (Mackey, 2016). Copper was first discovered in Australia in 1842 in South Australia not far from Adelaide; additional copper discoveries in the region soon followed. At first, copper ore was shipped to Swansea, Wales for smelting (Bampton, 2003). However, in addition to the long, 150 day one-way sea passage, it seems Welsh smelters preferred higher grade of ores – these aspects and likely a mood in the new colony to be independent of Swansea (Evans, 2014) evidently encouraged local smelting at the mine sites using small, Welsh-type reverberatory furnaces fired with hardwood as fuel and operated by Welsh and Cornish migrants. The first large copper smelter in Australia commenced in 1848 at Bremer, near Callington some 60 km east of Adelaide. With larger discoveries on Yorke Peninsula, the Wallaroo copper smelter at Wallaroo Bay on the west coast of the peninsula commenced operations in 1861 (Bell & McCarthy, 2008). Thus began one of the most successful, and in its day, one of the most advanced and innovative plants in Australia if not the world. In the late 1860s, it was considered one of the largest copper smelters in the world (Bell & McCarthy, 2008)

Jan 1, 2019

By S. F. Featherby

"This paper traces briefly the historical development of coal handling systems to meet the needs of a rapidly developing thermal power generation technology. The wide range of operating requirements is demonstrated by comparing and contrasting the Wabamun GS of Calgary Power Ltd. and a typical modern Ontario-Hydro thermal plant. The problems of safe storage of large tonnages of coal in stockpiles are discussed, together with recommendations for stockpile management. The development of coal bunkers and their management is discussed in detail, together with future trends in the industry."

Jan 1, 1966

By M. Kuyumcu

After German reunification the mining industry in former East Germany was profoundly restructured. Beside privatization of profitable companies the public sector took over responsibility for the mining operations to be shut down. Therefore state-owned companies cope with technical, ecological, and social challenges. The rehabilitation and reclamation has to rededicate former mining areas to new use and provided new jobs as well. In the lignite mining districts there are around 100,000 ha of mining area, a mining caused disturbance to the groundwater balance and to the system of surface water bodies of approx. 390,000 ha. They are called the largest landscape construction site in Europe. In addition to the results and diverse experience achieved over the past 23 years, a description will follow of our new challenges and of an outlook on remaining tasks. This article will describe the financing, as well as aspects of the jobcreation policy arising from lignite industry remediation.

Aug 1, 2013

By M. G. Lipsett

"The Mining Information Technology User Group considers information to be a strategic enabler to improved business performance in mining. This ad hoc group has been meeting since 2000 to share knowledge and leverage their efforts in effectively using IT in mining. In this paper, core issues to mining IT are reviewed, along with initiatives to engage industry professionals and decision-makers in the potential for improved use of information in their operations. Relevance of IT to Canadian MiningMining operations always drive to improve their performance, and so far they have succeeded by using different technologies. While economies of scale have come in fragmentation and material handling, and energy usage has improved through conservation and design of integrated mineral processing plants, these systems have the net result of tightening operational constraints, through reduced excess capacity. There are higher opportunity costs of lost production when integrated, large-scale systems are operating in a sub-optimal way.The problem is that it is profoundly difficult to run a mine in an optimal way. Optimization requires a defined objective function (e.g., profit), which is hard to pose, let alone solve, because so many inter-related aspects of an operation affect the bottom line. Even for a small, well-defined process state, it is difficult to measure all the pertinent information with sufficient accuracy to ensure that the system is performing well in real time.The art of mining remains making good decisions with uncertainty: in the orebody delineation; in the allocation of resources; in the efficiency of the operation; in the reliability of components and systems; and in responding to the downstream market. As well, individual decision-makers need to know how their decisions affect other processes and systems, so that improvements in one part of an operation do not result in such degraded performance in the rest of the plant that overall profitability goes down."

Jan 1, 2003

By Dr. Ralph W. Edie

The limestone reef reservoir at Swan Hills consists essentially of a "buildup" of successively smaller atoll-like layers. Precipitation of calcium carbonate within the lagoonal area of each layer essentially kept pace with growth of the outer organic lattice. Within the reef mass, six de-positional environments characterized by specific suites of fossils (or fossil fragments) and associated limestone textures are recognized as follows: ( 1) Aerated moderately agitated water of normal marine salinity (widespread shelf or submerged reef-built platform). Thamnopora-type corals, Amphipora, "pancake" stroma-toporoids, crinoids, articulate bra-chiopods, rare rugose cup corals, and ostracods occurs in light gray-buff skeletal microgranular limestone of low permeability. (2) Semi-stagnant quiet water of normal marine salinity (leeward side of reef). Crinoids, articulate brachio-pods, rare thamnopora-type corals, Amphipora, pancake and bulbous stromatoporoids, rugose cup corals, ostracods and gastropods occur in impermeable dark brown argillaceous skeletal calcilutite with thin black bituminous shale beds and rare dark chert nodules.

Jan 1, 1961

By L. Voisin, K. Yamaguchi, D. G. Mendoza, K. Ltagaki

The behavior of arsenic and antimony in the Cu-0 system was thermodynamically investigated to understand their elimination during a blister-making stage in copper smelting. Firstly, the phase relations in a miscibility gap composed of the liquid slag and copper phases in the Cu-0-As and Cu-0-Sb systems at 1523 K were established by a quenching technique. It was found that arsenic and antimony distributed preferentially into the slag phase in the miscibility gap. Secondly, the activities of arsenic and antimony in the miscibility gap of these systems were determined at 1523 K by using a double Knudsen cell - mass spectrometer method. It was clarified that the activity of arsenic in the copper and slag phases showed the negative deviation from ideality while that of antimony in the copper phase a slightly positive deviation. These data obtained in this study suggest a possibility to eliminate arsenic and antimony by means of over-blowing in a converter after discharging the slag.

Jan 1, 2007

By A. L. Hinde, H. Dong, J. T. Kalala

"The High Pressure Grinding Roll (HPGR) is gaining acceptance in the mineral processing industry and has become a competitive technology in reducing the specific energy consumption in Mineral processing plants. The amount of samples required for HPGR amenability testwork and HPGR wear tests is usually high and often cannot be available at early stage of projects were only a few drill cores are available.Although HPGR was initiated from small scale piston die compression tests, the development of small scale piston die test to predict the performance of HPGR has been slow.The objectives of this paper was to present the designs, operating procedure of piston-die press and operating conditions which have resulted in similar particle size distribution obtained from a piston die test and HPGR Labwal unit starting from the same feed size distribution. Testwork were conducted using a 2 MN piston-die press and a Labwal HPGR unit on major South African ore types, viz, gold, platinum and iron ores. The results obtained show that piston-die test can generate data to predict energy consumption, product size distribution, and even to evaluate the edge effect."

Jan 1, 2012

By R. Esteban, D. Runnels, J. Torrealba-Vargas, G. Couture

"Data handling is an important step in the development of a simulator of a mineral processing circuit. The model requires representative data of the scenario to be modeled. The model development involves protocols that must be followed very closely to complete a successful project.Data handling of large and diverse datasets (metallurgical test results, geological data, mining models, historical data, etc.) is a key element of the model. The information needs to be processed, reconciled, interpreted, modeled and presented to support the design or the optimization of a mineral processing plant.Best practice recommends that teams from different disciplines (such as mining, metallurgy, geology and environmental) interact to define the most important variables that could influence the simulator. For example by adopting a geometallurgical approach in the earlier stages of the project, it is possible to consolidate the number of main ore rock types in a testwork program (saving money and time) by involving geologists and metallurgists in the sample selection and data interpretation.Planning the development of a model involves an understanding of the software capabilities but also the limitations and the magnitude of the data required to calibrate the model in case of changes in the project.A successful model requires a deep understanding of the circuit to be modeled and thus plant personnel should be considered as members of the team.This paper describes the use of the "state of the art" tools for data analysis, simulation and optimization; and shows three practical examples of the use those tools in the design of mineral processing plants."

Jan 1, 2015

By D. P. Tripathy

A supply chain encompasses all the activities associated with the flow and transformation of goods from the raw materials stage(extraction), through to the end user. Supply chain management (SCM) is the integration of these activities through improved supply chain relationship, to achieve a sustainable competitive advantage and it rests on its ability to provide the right goods and services when and where needed. The supply chain is the vital component of any company?s value chain which links the operating processes to its supplier and customer. The globalization of business promises to offer new and unique challenges for the supply chain competencies of most firms. Challenges will also increase in the environmental aspects of supply chain often referred to as ?Green Issues?. The supply chain of mining industry comprises of the flow of material and information from the mine site, to processing and loading for transport, to the customer. However, due to recent changing environmental requirements affecting mining and mineral processing operations, increasing attention is given to developing environmental management (EM) strategies for the mineral supply chain. This paper focuses on: ? Environmental factors leading to the development of an extended environmental supply chain, ? Additional challenges presented by the extension, ? Performance measures appropriate for the extended supply chain, ? Developing a general procedure towards achieving and maintaining the green supply chain.

May 1, 2006

By Allan P. Fawley

ONE hundred miles from Vancouver, at an elevation of 4,000 feet, is the Pioneer mine. It is situated on Cadwallader creek, a tributary of Bridge river, and is reached by travelling from Vancouver to Squamish by boat, a distance of thirty-two miles, from there by train to Bridge River (one hundred and seven miles), and finally by automobile across Mission mountain .(7,000 ft. elevation) to the mine (fifty-six miles): a total distance of one hundred and ninety-five miles. Prior to 1924, many Companies had examined the Pioneer, which had been developed by shaft to a depth of 200 feet, but, while values were good, the small size of the ore-shoot discouraged large investors. In July, of that year, opera-tions were re-commenced by the late David Sloan and, on sinking further, the ore-shoot was found to lengthen greatly as well as to ex-tend in depth, while remarkable gold values also were encountered. When, later, the price of gold rose from $20 to $35 per ounce, the mine was in an excellent position to take full advantage of the increase + and not only became an extremely profitable enterprise itself but its success greatly stimulated the search for and development of other 1-gold properties in British Columbia.

Jan 1, 1937

By Tom Gaines, G. S. Brant, J. G. Debanne

"AbstractThe Bonnie Glen oil field, one of Canada's largest, lies about fifty miles southwest of Edmonton, Alberta. One hundred and thirty-eight wells have been completed in this field since its discovery in January, 1952. Five different procedures have been used in completing the producing wells.The reservoir is an Upper Devonian biohermal reef with good porosity and uniformly high permeability. The top of the reef is quite flat but the flanks slope at angles approaching 20 degrees from the horizontal. The reservoir has a gas cap with a maximum thickness of 400 feet, an oil column of 300 feet, and a :porcus aquifer of over 300 feet. The reservoir pressure is now 2,400 pounds per square inch gauge at datum ( -4100 M.S.L.).Because of the high permeability and the high •pressure, lost circulation and resultant blowouts are a particular hazard in drilling at Bonnie :Glen field. To reduce the dangers of blowouts, it is general practice to run casing to the top of the reef. If the reef is encountered 'high' it was usual practice to run a liner and perforate for completion. Wells penetrating the •reef below the gas/oil interface were either completed in open hole or through casing perforated opposite the oil pay, with the former method more frequently used. Eight wells were completed by the Humble-Otis permanent-type completion, and recently five high wells were completed open hole with the gas •cap exposed. This latter completion, 'tubing submergence', has proved highly satisfactory thus far.The open-hole type of completion is cheaper than the liner perforation method and results in better well performance. More experimentation and data are needed before the tubing submergence method can be recommended unqualifiedly. but all evidence thus far favours its use in reef reservoirs."

Jan 1, 1955

By G M. Thorpe

This paper discusses mine research at Inco, giving specific examples of research projects which illustrate the approach to mining problems. The first example covers the development of a new mining method, "undercut and fill," which was originated for mining badly broken-up pillars, but which is now rapidly replacing the square set method of pillar recovery. In the new method, ore is extracted in a series of successive horizontal cuts, progressing downward, a cut being completely mined and filled before the cut below is started. In the second example, improvements to the "cut and fill" method of mining are discussed. These improvements are the result of improved techniques and improved equipment, etc., with, in many cases, the former being made possible by the latter. The advances made have permitted the use of the "cut and fill" method at much greater depths than before. The third example is presented to illustrate research undertaken to obtain the earliest maximum advantage of the introduction of a new piece of equipment or material. For this purpose, the development of the "Under-ground use of AN /FO Blasting Agent " has been selected. Work on this project started in May, 1960, at a time when there was very little in-formation regarding the potentialities of AN /FO for underground blasting, either primary or secondary. By the end of 1961, AN /FO made up 64 per cent of the explosives used under-ground at Inco mines.

Jan 1, 1963

By William M. Luff

This paper outlines the regional geology and history of the area, and summarizes the stratigraphy, structure and geology of the Brunswick No. 12 mine area. The Brunswick No. 12 deposit is a stratiform massive sulphide body. It occurs in rocks of the Tetagouche Group, which is believed to range in age from Lower to Middle Ordovician. The stratigraphic sequence, including the stratiform orebody, in ascending order consists of older metasedimentary rocks, augen schist, metasediments, augen. schist, footwall metasediments, the -massive sulphide body, iron formation, hanging-wall metasediments, siliceous tuff, basic volcanic rocks , basic iron formation and a porphyry dyke. This sequence is similar to that at some other deposits in the area. Four phases of structural deformation are known to be present in the Brunswick No. 12 mine area. The first deformation folds (F1 ) and associated faulting are the most important factors in determining the distribution of the massive sulphides. This deformation has resulted in the massive sulphides being separated into four zones: the Main Zone, the West Zone, the East Zone and the V-2 Zone. Brunswick Mining and Smelting Corporation Limited is actively mining, developing and exploring the deposit.

Jan 1, 1977

By Engineering Staff

In 1958, the Iron Ore Company of Canada decided to proceed with the Carol Project. The ore deposits in the area are part of the highly metamorphosed southern zone of the Labrador Trough. They lie along the shore of W a bush lake, in the western part of Newfoundland-Labrador, 190 miles north of Sept-Iles. The project is designed to mine, by open-pit methods, 17,200,000 long tons of crude ore, grading 37 per cent iron, per year. This ore will be beneficiated to produce 7,000,000 long tons of concentrate, grading 66 per cent iron, of which 5,500,000 long tons will be pelletized. Production is scheduled to commence this summer. Initially, ore will be taken from 45-foot benches in the Smallwood mine, using jet-piercing production drills and large-scale blasting with "slurry" explosives. Four 13-yard electric shovels will muck the broken ore into 100-ton trailer trucks. The trailers will be hauled to two 2,000-ton loading pockets, which feed the ore into 100-ton railcars. Four ore trains, each comprised

Jan 1, 1962