Search Documents

By Paul Hosford, Tim Haldane

"The paper describes the fast-track development of the project from feasibility study through to detailed design and construction, highlighting the process adaptations for handling sticky ore and water management in a tropical environment, and subsequent commissioning and operating experience of the mine. The paper discusses the geological setting, the environmental and socioeconomic considerations in developing and operating a mining operation in an underdeveloped country and the logistical challenges involved in bringing a large capital investment into Central America.INTRODUCTIONGlamis Gold Ltd. acquired the San Martin project in Honduras as a result of its merger with Mar-West Resources in late 1998. Despite the prevailing low gold price environment at the time of acquisition, Glamis anticipated rapid development of the San Martin project due to the quality of the deposit and other positive factors.Following favorable exploration and permitting activities in the first half of 1999, Glamis prepared a Feasibility study. In October 1999, Glamis decided to proceed with the development of the project and selected Hatch to provide the engineering, procurement and construction management services for the project. The San Martin project was in full-scale commercial operation approximately 14 months after the receipt of Board approval, and by July 2001 the San Martin project was operating at approximately 150% of its feasibility design capacity."

Jan 1, 2002

By A. J. Williams

"Conventional base metal milling practice normally consists of crushing, grinding and cyclone classification followed by flotation. It is the authors' belief that the commencement of flotation after cyclone classification leads to inferior metallurgical results and that implementation of flotation of grinding mill discharges can result in increased recovery due to reduced overgrinding, reduced activation of contaminating minerals and improved dewatering circuit results due to the production of coarser concentrates.The concept of recovering minerals from the discharge of grinding mills is not new! Gold concentrators have utilized jigs and flotation cells while iron ore plants have employed magnetic separators to recover gold and magnetite respectively from the discharge of grinding mills. More recently, a Reichert cone has been used to recover sulphide and oxide base metal minerals from screened rod mill discharge. 1To the authors' knowledge, the first application of flotation of base metal minerals from the discharge of a production plant grinding mill was at the Lake Dufault concentrator of Corpor'1tion Falcon bridge Copper. Located 10 miles north of Noranda, Quebec the Lake Dufault concentrator commenced operations in August, 1964.The installation of flot11tion cells in the Lake Dufault grinding circuit proved so successful that an identical system was installed in the Manibridge concentrator of Falconbridge Nickel Mines Limited. Located 90 miles southwest of Thompson, Manitoba the Mamibridge concentrator commenced operations in June, 1971 and due to exhaustion of economic ore reserves discontinued production in May 1977."

Jan 1, 1984

By D. Wolfe, R. Cleminson

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. The slurry systems at Aurora experience high rates of wear, and mission lengths on current slurry pumps are nominally 1500-2000 hours. Recent work has enabled a better understanding of the significant adverse effect of large particle impingement damage to impeller vane leading edges - which is the known life determining issue for Aurora hydrotransport pumps. A new pump design has been developed with a larger diameter impeller and increased vane lengths, and is expected to triple Aurora’s mission length for hydrotransport pumps.INTRODUCTIONSlurry Pumps are Critical Equipment at SyncrudeSlurry pumps are a critical component in Syncrude’s operations. In a typical Aurora application, each pump stage helps move over 8000 dry tonnes per hour of oil sand, plus an equal volume of process water that has been added to create the slurry. The average impeller life in oil sand hydrotransport service at Aurora has been nominally 1500-2000 hours, or 12-16 million tonnes of oil sand pumped. Generally, the slurry pump application at Aurora has proven very difficult to improve due to the unique combination of high sand abrasivity, 125 mm (5”) large particle top size (lumps), and high flow rate relative to basic pump size; a factor that results in higher than optimal impeller vane speeds for the service conditions.PROJECT BASISSlurry Pumps are the Reliability Bottleneck at AuroraSlurry pumps are currently the shortest-lived components that determine the overall system run length at Aurora, in Hydrotransport, Extraction and Tailings. Vibrating screens and piping had been previous bottlenecks, but their reliability has been improved through upgrades in equipment design and wear materials. Both vibrating screens and piping can now achieve 4000 hour mission lengths."

Jan 1, 2013

By C. Pelley, S. Kelebek, G. Kunzel, S. Gregersen, M. Pollanen

A series of small-scale tests was conducted to evaluate the effect of micro-fracture development, imposed by blasting, on the material properties of the rock as well as its resistance to crushing and grinding. The uniaxial compressive strength, tensile strength, Poisson’s ratio, Pwave, S-wave velocity, point load test index, crushing, and grinding work indices were evaluated for samples without any blasting load and for samples which had received a variety of blast loads ranging from a single impact with a lowstrength detonating cord to a combination of impacts at different times and significant impacts with powder factors close to those used in practical blasts. It was shown that the rock mechanics parameters change even at low impacts, suggesting easier crushing of the rock. Damage values appear to be affected by timing as stress wave superposition affects the damage process. Fragmentation is achieved at higher impact levels while work index modification of the fragments is also observed when high powder factors are used, suggesting improvements in grinding.

Jan 1, 2006

By J. J. Montoro

The influence of blasting on the excavators’ efficiency, defined as mucking rate (amount of rock mucked per unit time) and mean bucket load (amount of rock loaded in each bucket operation), is investigated. Rock characteristics, blasting parameters (drill pattern, explosive energy, and charging), and the excavator’s performance (truck loading time and number of buckets to fill a truck) were monitored in eleven blasts in an open pit iron ore mine. ANFO, ANFO/emulsion blend, and watergel were used in the blasts and the powder factor was varied between 0.98 and 1.45 kg/m3. The mean bucket load is mainly affected by the bucket size, which is independent of the blasting parameters. Besides the relation with the mean bucket load, the mucking rate was found to be positively correlated with the explosive energy, whereas no significant correlation with the rock properties was found. The analysis of the data, together with other published works, suggests a non-monotonic relation of the mucking rate with the powder factor, with a maximum mucking rate at a certain powder factor. This is especially true when the useful work of the explosive per unit rock volume is used rather than the classical mass powder factor and when only the amount of explosive above grade is considered.

Jan 1, 2007

By G. Halverson, K. Blower

"Giant Yellowknife Mines Limited (Giant) has been producing gold since 1948. Located at Yellowknife, Northwest Territories, Canada, see Figure 1, the mine processes approximately 1,200 short tons per day of 0.23 ounce gold per ton of ore.The majority of the gold in the ore is sub-microscopic and associated within the mineral arsenopyrite. This association complicates the extraction method since straight cyanidation will only recover 30% of the gold. The operations at Giant involve four essential steps, with an overall recovery of 87%. The steps shown in Figure 2 are crushing and grinding, flotation, roasting and cyanidation. These processes result in a number of effluent waste streams characterized in Table 1. These streams are combined and sent to a tailings storage pond for subsequent treatment prior to discharge to the environment.Giant is located just north of the 62nd parallel where winter temperatures drop to -40°C for extended periods. This entails storing effluent in dams over the seven month winter period for treatment during the relatively short summer season.The treatment method currently employed at Giant is an ""alkaline chlorination-arsenic precipitation-flocculation"" process. The pond water is subjected to three phases of treatment prior to being discharged to the environment as shown in Figure 3."

Jan 1, 1987

By E. C. Morton

The Western Australian School of Mines (WASM) has developed a facility for the static testing of large scale ground support elements. The samples are loaded using a mechanical screw feed jack. Instruments measure the displacement and the load being applied. Methods have been developed for testing of mesh, shotcrete and membranes. Mesh samples are restrained on all sides and loaded centrally. A new large scale punch test method has been developed to evaluate shotcrete and membranes. These products are sprayed on to a sandstone substrate containing a centrally located isolated disc. The sprayed product is loaded by displacing the disk. The different test methods are described in detail. The test program involved two types of mesh, several shotcrete mix designs with different curing times and one membrane product. The force-displacement responses are used to directly compare the products. The implications for implementation of the different ground support products are discussed.

May 1, 2009

By Graham Davey

"Ultrafine grinding of minerals has been in wide spread use in the industrial mineral field for over 30 years. Within the last 10 years the metalliferous industry has shown interest in the ability to produce ultrafine particles, as chemical, physio-chemical and physical separation processes have advanced to be able to treat ultrafine metalliferous particles. Also as the primary mineral deposits are depleted, new more difficult deposits must be mined. Existing operations are also looking to maximize economic return from existing deposits, requiring new thinking and technologies.The recent development of industrially proven and cost efficient technologies for ultrafine grinding has opened up another processing option for the treatment of finegrained metalliferous and refractory gold ores. The current commercial designs are variations of stirred mills used in the industrial minerals sector for the past 30 years. For the purposes of this paper ultrafine grinding is considered to be P80 of less than 15 microns.Attrition milling to fine grind sizes presents some challenging issues relating to scale-up including the dearth of information on the quantitative impact of feed and operating conditions, as well as the precise and accurate measurement of particle size distributions. Two examples from recent installations will be analyzed including Thalanga Copper and Century Zinc Mines. Both have diverse grind size targets for the SMD, yet both have realized significant metallurgical gains."

Jan 1, 2002

By Rick Wilkins

The stability of steep embankments is a major safety issue in open pit mining, highway passes, and earth filled dams. A failure in any one of these situations could mean a loss of very expensive equipment, a long term inconvenience, and more importantly, a loss of life. These possible catastrophes could be avoided by installing a reliable real time monitoring system. Robotic total stations (RTSs) give one possible cost effective solution to creating a near real time monitoring system. Repeated surveys at predetermined time intervals can automatically generate warnings if slope movements exceed a preset tolerance level. The variation in atmospheric refraction, combined with possible instabilities in reference targets, can make a monitoring system based on RTSs produce false alarms. A methodology has been developed at the Canadian Centre for Geodetic Engineering (CCGE) for reducing these systematic error effects. The methodology has been realized in the creation of a software package that has been successfully implemented at large earthen dams in California and at an open pit mine operation in British Columbia.

May 1, 2002

By J. Gordon Parr, D. A. Whitaker, G. A. Yorko

High purity alloys of zinc with 25 per cent to 50 per cent aluminum, have been prepared. Mechanical properties of the as-cast and heat-treated alloys have been related to constitution, determined by x-ray diffraction and microscopic methods. Investigations include the effects of aging and of small nickel additions on the properties of the alloys.

Jan 1, 1960

By Colin Lindsay

"The Collahuasi copper mine, located at an altitude of 4300 meters above sea level in northern Chile, commenced operations late in 1998. The mine is currently the 4‘h largest copper producer in the world and comprises an open pit, a 60,000 tpd sulphide concentrator, a 15,000 tpd oxide heap leach and SWEW plant and a 200 km concentrate pipeline to a port facility.Constructing, commissioning and operating a mine at high altitude presents unique challenges in terms of the performance of both equipment and people. It is important that these be recognized and carefully considered during the feasibility study and the detailed design stages and the success of the Collahuasi project is largely due to this. The plant design incorporates a number of features aimed at mitigating the problems of altitude and the construction methodology also took into account the particular site conditions.This paper discusses the Collahuasi project team’s approach to planning for the remote location and also some of the problems experienced during construction, commissioning and operation.INTRODUCTIONThe Collahuasi mine is located in northern Chile, some 250 km to the south-east of the port of Iquique and 15 km from the Bolivian border. The mine facilities lie between 3800-4300 m above sea level on the Altiplano, the central plateau of the Andes mountains, and cover a total of approximately 95,000 hectares. Although the area is arid, it experiences an average of 150 mm of precipitation annually and weather conditions can be extreme. Temperatures during the day range between -3 to +11 º C and are generally below 0ºC at night, sometimes as low as -20°C. High energy winds are common and humidity is low. Much of the precipitation occurs during the winter as snow but there also occurs a period during the Chilean summer known as the “Invierno Boliviano’’ (or Bolivian Winter) which is characterized by severe electrical storms and rain."

Jan 1, 2001

By Patrick Pelletier, Pierre-Alexandre Bossé, Julie Fournier, Gianni Bartolacci, Jayson Tessier, Ahmed Bouajila, Carl Duchesne

"This paper summarizes research into the study of the control of flotation processes based on froth images. The use of numerical image analysis techniques for the extraction of significant patterns (froth structure and colour) from industrial flotation froths is discussed.First, the froth was analysed by the use of the Multivariate Image Analysis (MIA) method to extract the spectral variation contained in a RBG image. The Partial Least Squares (PLS) was applied to develop the empirical model for the prediction of froth grade. The results of this application are illustrated using one industrial case study.Second, the froth was also analysed by Gray Level Co-occurrence Matrix (GLCM) and Wavelet Transform Analysis (WTA) to extract features related more to morphological aspects. Since there is useful information hidden in froth texture, these methods are used as texture descriptor to classify different types of froths.Third, a control strategy based on a froth structure indicator was developed and implemented on an industrial zinc flotation circuit. The feedback controller uses a reagent flow-rate in order to maintain the froth structure at its set point. Process improvements obtained with the implemented control strategy are highlighted.Finally, the feasibility to implement a hybrid control strategy consisting in a froth structure supervision controller based on the froth concentrate grade estimated by MIA and recovery inferred by image analysis is discussed.INTRODUCTIONThe development of control strategies to achieve satisfactory control performance has always been a great challenge for engineers and the need for improved process diagnosis, control and optimization has become more and more evident for the mineral processing industry in the last decades. That is why new process variables need to be measured particularly in highly multivariable processes such as flotation. This industrial process is subject to a wide variety of disturbances mainly generated by frequent and sometimes abrupt changes in physical and/or chemical ore characteristics and also, due to some irregularities in manual process operating procedures. A flotation circuit scheme is always a complex network of more than two dozens slurry streams. Information about those streams (% solid, metal content analysis and flow rates) is important for process diagnosis performance evaluation and control. Also, because of the grade decrease and increasing complexity of the new processed ores, more instrumentation outputs and more powerful and significant pr"

Jan 1, 2005

By Brian Danyliw

"Dust control is an increasingly important consideration for all mining operations from a health, safety, environmental and maintenance perspective. Modern mining operations incorporate a variety of mechanical dust control techniques into design however in many cases these engineered systems are unable to meet desired fugitive dust level targets. In these cases a variety of chemical dust suppression options are available to operators to assist in meeting their targets. This paper provides an overview of available chemistries, discussion of application techniques and equipment requirements and available performance monitoring technologies. This paper will also include a number of case histories discussing the treatment approach chosen, challenges encountered, chemical feed, storage and application equipment, monitoring techniques employed and results achieved.INTRODUCTIONDust FundamentalsFugitive dust by definition is an aerosol consisting of particulate matter suspended in a gaseous medium. Aerosols can include suspensions of particulate (solids) or sprays (liquids) or a mixture of both. Of particular concern from an occupational health and safety perspective are aerosols of particulate matter due to their involvement in classical occupations lung diseases such as silicosis, poisoning through chronic exposure to compounds such as lead and beryllium and expected involvement in more modern identified conditions such as cancer, asthma, and a host of other respiratory and non-respiratory conditions which may be caused or influenced through exposure to dust.According to the ""Glossary of Atmospheric Chemistry Terms"" (IUPAC, 1990), ""Dust: Small, dry, solid particles projected into the air by natural forces, such as wind, volcanic eruption, and by mechanical or man-made processes such as crushing, grinding, milling, drilling, demolition, shoveling, conveying, screening, bagging, and sweeping. Dust particles are usually in the size range from about 1 to 100 µm in diameter, and they settle slowly under the influence of gravity."" It should be noted that the behavior of particulates with respect to settling rate in air is a function of particle mass and shape and therefore the geometric size of the particle can be misleading. Occupational hygienists utilize the concept of particle aerodynamic diameter as a more representative reflection of particle size. Particle aerodynamic diameter, is defined as ""the diameter of a hypothetical sphere of density 1 g/cm3 having the same terminal settling velocity in calm air as the particle in question, regardless of its geometric size, shape and true density."" The expression of particle size as aerodynamic diameter allows for a more consistent understanding of particle behavior both from a settling perspective as well as from the perspective of how dust particles will behave in the respiratory tract. Figure 1 illustrates settling rates for particles of various aerodynamic diameters. The relationship between particle size and settling rate is important for understanding what size of particles must be addressed by dust control strategies as well as what particle sizes represent the most danger from an exposure and occupational health perspective."

Jan 1, 2015

By Andre Vien, Jean-François Dupont

"Over the past several years, Svedala has developed a continuous charge monitor (CCM) for tumbling mills. It consists of a strain gauge embedded into a rubber lifter and associated electronics. This paper describes the installation and use of such a device on a SAG mill at the Holt-McDermott Mine. Comparison to measured static volumetric load and bearing pressure and inclusion of the measurement into a control strategy and its potential for condition monitoring is discussed. INTRODUCTIONWhile the measurement of load is very important in all kinds of grinding applications, the biggest benefits are expected from AG and SAG milling. This is what motivated Holt-McDermott to take a closer look at this problem, with a view to optimizing SAG mill performance.In many cases, the SAG mill control problem can be stated as maximizing throughput while avoiding a volumetric overload, with the other constraints (e.g. power, grind size, upstream/downstream equipment constraints, etc.) playing a less important role. This is certainly true at Holt-McDermott where the SAG mill is the production bottleneck about 90% of the time, and anything that can be done to increase SAG mill throughput will have a significant impact on operating profit.Although the goal of maximizing throughput while avoiding volumetric overload is simple to state, it has proven to be much more difficult to achieve. The mineral processing industry has expended a great deal of time and effort to devise control strategies in the pursuit of this objective. While much progress has been made, there is still room for considerable improvement. Across the industry it is probably fair to say that overloads occur relatively infrequently, but the real losses accrue as a result of the tendency to run rather conservatively."

Jan 1, 2001

By M. Ramström

"In 2002, Atlas Copco Rock Drills AB released the new rig control system (RCS) technology for all of its drill rig types. RCS opened the way for a new generation of computerized drill rigs based on modern, standard PC-computer technology. Drilling accuracy, information logging, reduction in manpower in some types, and serviceability have all taken a quantum leap forward when compared with previous generations of drill rigs. RCS is modularized and distributed by means of CAN-bus technology. This technology, which is well proven in automobile applications, forms the communication backbone of the rig. The modularity facilitates almost unlimited possibilities for the expansion and adaptation of drill rig functions."

Jan 1, 2005

By Phillip Cancilla, Daniel Roy, Frank Rosenblum

"The manual moisture determination methods employed today by mineral processing plants falls short in providing timely information required for automation control. The costs associated with transporting and handling concentrates still represent a major portion of the overall treatment price. When considering the cash flow of a mining operation, that is governed by both the smelter contract, with moisture penalties and the quantity and quality of the concentrates shipped, an efficient method of on-line moisture content would be a welcome tool.A novel on-line determination system for ore concentrate moisture content would replace the normally tedious classic manual procedure. Since the introduction of microelectronic-based control systems, operators have strived to reduce the treatment costs to the minimum therefore a representative and timely determination of on-line moisture content becomes vital for control set points and timely feedback. Reliable sensors have long been on the “wish list” of mineral processors since the problem has always been that you can only control what you can measure. Today, the task of moisture determination is still done in the classical technique of loss in weight by uncontrolled procedures. These same methods were introduced in the earliest base metal concentrators. Generally, it is acceptable to have ore concentrate moisture content vary within a range of 7 to 9%. Many times, delays in manually achieving reliable feedback on the moisture content results in the moisture varying from 5 to 12% before corrective actions can be made.This paper first reviews the traditional and widely available methods for determining moisture content in granular materials by applying physical principals and properties to measure moisture content. All methods are in some form affected when employed on mineral ore concentrates. This paper describes a unique and promising on-line moisture sensor in two mineral processing applications, which not only automates the tedious tasks but also results in reliable moisture feedback that can be used in the optimization of the de-watering process equipment such as pressure or vacuum filters and fuel-fired driers. Finally, two measurement applications will be presented to indicate the usefulness and to summarize the measurement requirements for the proposed method of employing drag force and mechanical properties of the material itself to determine the moisture content."

Jan 1, 2001

By Frank B. Amon

Highland Valley Copper had to make some significant changes in the way it was working in order to counter the effects of ever-increasing costs and decreasing metal prices. A mine/mill optimization plan started in 1997 introduced new technologies and management approaches that resulted in a dramatic drop in cash breakeven costs. The changes involved employee training, added authority and responsibility for staff, better communications, and a consistent approach to setting and achieving property-wide goals. The net effect was to change the culture of the organization from one that was fragmented and focussed on local objectives to one that is cohesive and has common goals. These changes have allowed the mine to remain in business during a protracted period of low metal prices, and have positioned the mine favourably to benefit even more from any future increase in prices.

May 1, 2004

"The link between ore texture and mineral liberation has previously been established at a microscopic scale. To construct ore texture models that can be used in mining applications requires this relationship to be retained at a significantly larger scale. This is initially dealt with by finding a basic set of microtextures that form the elements of the ore textures at the next larger mesoscopic scale, simulating these mesotextures at a fine scale, then changing the support of the mesotexture simulations to generate the expected mining block/stope mesotexture distributions. Thus, a mutually exclusive and exhaustive set of spatially locatable mesotextures can be used to fully characterize the metallurgical properties of in situ material.A method that generates expected distributions of mesotextures for any mining block size or shape is proposed, and includes: (1) characterizing the spatial correlation of the set of mesotextures with a single covariance function; (2) generating multiple simulations of mesotextures at a fine scale; and (3) using the simulations at a fine scale to generate the expected mining block/stope mesotexture distributions. A case study, using the George Fisher sediment-hosted base metal deposit in Queensland Queensland, Australia, is developed to demonstrate the proposed methodology as well as show the inadequacy of off-the-shelf approaches.Mining-scale texture models can be used to improve the in situ discrimination of ore from waste by exploiting the joint spatial variability of grades and textures to quantify the expected metal recovery of in situ material, then calculate local marginal cut-off grades. An artificial case study is presented to demonstrate the changes in ore/waste selection when considering ore texture models compared to constant metal recoveries."

Jan 1, 2005

By Dayle Denton, Lloyd Buckingham, Kenneth G. Thomas, Jacques McMullen

"The dry grinding and leaching circuits of Barrick Gold’s new Roasting Facility at Goldstrike Mine in Nevada, USA incorporate well proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available technologies from the perspective of capital, environment and operating costs.Crushing is a two stage process using gyratory and cone crusher. Ore is stockpiled and then reclaimed to two parallel dry grinding mills. The double rotator dry grinding mills include a drying chamber, coarse and fine compartments and utilize a gearless motor drive (GMD) or “wrap-around”. In-circuit product transfer is accomplished with air slides and bucket elevators. Finished product separation is performed by both static and dynamic classifiers with the final product captured in baghouses. Recycle of unfinished product utilizes cascade chutes.The final ground product reports to two 2000 ton roaster feed silos. The two-stage oxygen flu-solids roasters with their associated gas train are the subject of a separate paper.The cyanide leach circuit is a standard carbon in leach system with circular swept screens for interstage carbon retention. The loaded carbon is sent to the existing Goldstrike autoclave plant for stripping and regeneration. Tails, after cyanide destruction, are deposited in the existing tailings dam with tails from the autoclave facility.Throughout the circuit, Clean Plant Design criteria were used to assure environmental compliance, ambiental acceptability and ensure worker health and safety. The commissioning and operation of the double rotator grinding technology has been very successful at Barrick Goldstrike."

Jan 1, 2001

By Stratton-Crawley R., G. E. Agar

"A study has been done of the scale-up of laboratory bench-scale flotation to continuous plant circuit performance. It was found that the impellor speed and the air flow rate influenced the results and in this case extreme values of these operating variables were required in order to reproduce the plant rougher results in the laboratory. Despite the experimental uncertainty introduced by these extreme values, it was demonstrated that the plant performance could be predicted and experimentally reproduced with bench-scale tests.IntroductionThe mineral processing industry relies heavily on batch flotation testwork to design flowsheets, evaluate reagent s and compare various types of ore. The batch tests are generally regarded as being directly comparable within themselves, but quite often they relate poorly or not at all to continuous circuits. Obviously this dilemma generates considerable uncertainty with wide-ranging ramifications. One of the manifestations of this unfortunate situation is the commonly expressed opinion that ""it may work that way in the laboratory, but it will never work that way in the plant"".In a previous publication, a method was described whereby the results of batch bench-scale tests could be used to simulate a locked cycle flotation test series. The work to be described here is a continuation of that investigation with an extension to the simulation of an actual plant circuit. It would have been preferable to progress from laboratory batch data to a continuous pilot plant and then finally to a full-scale plant operation. However, because that possibility did not present itself, an attempt will be made to show that the performance of an existing plant circuit can be successfully simulated from batch data. The success of the procedure can be judged by the agreement among the plant results, a locked cycle test and the predicted results based on batch tests."

Jan 1, 1982