Search Documents

Reliable estimation of in situ stress is a major step in the analysis and design of underground excavations in rock, particularly for evaluating the stability of underground structures to prevent failure or collapse. In the last ten years, the Western Australian School of Mines (WASM) has studied and developed an AE stress measurement technique using orientated core named the WASM AE method. It allows the determination of a representative and detailed knowledge of the in situ stress field during the early stages of a project (such as mine feasibility studies), even in areas where development access is not yet available. The method has been used for in situ stress measurement at more than 80 mine sites worldwide with over 200 individual stress measurements carried out to date. This paper describes the sample collection, sample testing and reconciliation of results for very deep measurements carried out at the Craig-Onaping mine complex in Sudbury Canada. The results constitute the deepest measurements undertaken to date at the WA School of Mines and indicate that the main principal stress is horizontal and oriented parallel to a common regional sub trend in a NE/SW direction.

May 1, 2009

By Hasan Ozturk

Laboratory testing examined the effect of a variety of intrinsic rock properties and environment conditions that influence the adhesive bond between rock and thin spray-on liners. The liner materials used for these tests were Tekflex, provided by Fosroc, Castonite, provided by Rohms and Haas Co., Rockweb provided by Spray-on Plastics, and CS 1251 2K, provided by Master Builders. Some of the variables examined include: rock strength (tensile/compressive strength) rock mineralogy, rock surface roughness (grain size, fracture/joint roughness), and surface contamination (oil, water or dust). Under optimal conditions, adhesive strengths reaching at least 3 MPa can be achieved. Where the rock surface is contaminated with dust or the rock is weak in tension, it may be difficult to reach adhesion strengths of 1 to 1.5 MPa.

May 1, 2004

By P. C. Benedict

"The Island Mountain mine is at the southeast end of Island mountain; across Jack of Clubs lake from the Cariboo Gold Quartz mine.; The orebodies consist of quartz veins and pyritic replacement deposits in limestone. To December 31; 1944; there has been mined 296; 273 tons of quartz-vein ore averaging about 0.34 oz. gold a ton; and 101; 002 tons of sulphide ore averaging about 0.83 oz. gold a ton; a total of 397; 275 tons averaging 0.46 oz. From this; 175; 985 fine oz. of gold and about 26; 450 fine oz. of silver were recovered; having a value of $6; 510; 521.More than 95 per cent of the production has come from a band 500 feet wide along the contact of the Rainbow and overlying Baker members and extending about 100 feet into the latter. Evidence that the Rainbow belongs stratigraphically above the Baker is presented later in this paper. Both members are most variable lithologically, and individual beds and whole series of beds pinch out in short distances. In part, at least, this is due to squeezing out incidentally to intense folding. No section can be claimed with assurance to be really representative. However, both memb.ers are composed predominantly of quartzitic rocks. Both contain argillaceous quartzite, argillite, limy quartzite, limy argillite, limestone (marble), and minor amounts of highly ankeritized rocks believed to be igneous sills possibly originally approaching diorite in composition."

Jan 1, 1954

By R. N. Murarka

"Hydrocyclone modelling and selection procedure is illustrated. Computerized procedure for hydrocyclone cut size determination for grinding and non-grinding applications is described.A standard procedure for evaluating operating hydrocyclones is described in detail. Many case studies are illustrated comparing actual plant performance with the computer simulation output in terms of overflow product size distributions.INTRODUCTION Cyclones are widely used for applications such as: close circuit grinding, backfill, tailings and dewatering. Normally, cyclones are used for very fine separations where screens are not suitable or too expensive. Figure 1 shows the separation size range of various classifying devices. Cyclones are popular because of their low capital and operating cost. Cyclone selection procedure for different applications depends on the amount of information available on the cyclone feed slurry characteristics. Closed circuit grinding applications will be discussed in detail in this paper. The Cut Size:The size of the material in the feed which reports 50% to each product stream (i.e. underflow and overflow), after correcting for the feed solids by-passing with the underflow liquid, is termed the cut size or ""d50c"". This is often used as the criterion and the basis for cyclone design.When the corrected recovery to underflow of each mesh size in the feed is plotted against the geometric mean size in microns on a log scale, the micron size corresponding to 50% recovery is the d50c size."

Jan 1, 1992

By I. Nakatsugawa

Chemical conversion coating is a process to create thin oxide/hydroxide film containing several inorganic/organic compounds by way of chemical deposition reaction. In case of the application to Mg mobile electronic housings, the film should possess a good electric conductivity while keeping adequate corrosion resistance and working as a paint base. The use of toxic/hazardous chemicals is strictly prohibited from the environmental aspects. This paper describes the recent trend of conversion coating used for Mg electronic housings and analyzes critically from the point of surface technology. The importance of cleaning process and understanding of surface microstructure are particularly emphasized with several experimental results.

Jan 1, 2006

By D. A. Jacobson

Mining operations, whether new or existing, are constantly looking for ways to maximize production and improve energy efficiency, while keeping the footprint required to a minimum. The Nordberg MP1250 cone crusher was designed with these three goals in mind. A series of side-by-side evaluations comparing an MP1250 to an MP1000 were completed at two Freeport-McMoRan operations. The first evaluation began October 2009 in a tertiary position and the second began March 2010 in a secondary position, where it remains in full production today. Utilizing 25% higher power capacity than the existing MP1000 tertiary crushers, the MP1250 had 29% higher capacity and 17% lower specific energy, adjusted for differences in feed and product size. The MP1250 compared to the existing MP1000 secondary crushers achieved 30% higher capacity at a slightly reduced specific energy, while achieving a finer product. The MP1250?s higher capacity and energy efficiency may have application in many crushing plants. Depending on site specific economic factors, greenfield projects may benefit from a smaller footprint and less ancillary equipment, whereas brownfield projects may benefit from higher capacity or a finer product within the same footprint.

Jan 1, 2012

By C. Samson, R. S. Smith, S. W. Hefford

"Abstract - Time-domain electromagnetic systems are most sensitive to highly conductive targets during the transmitter on-time. Data collected during the on-time is highly influenced by the geometric relationship between the transmitter and the receiver. Unless corrections can be applied for these geometric variations, the ability to correctly detect and identify highly conductive targets can not be fully realized. Variables affecting the relative position between the transmitter and receiver include changes in the position of the receiver with respect to the transmitter, variations in transmitter attitude, and transmitter loop deformation. The level of accuracy in the determination of the relative geometry required to permit complete removal of the effects due to geometric variations is different for each of the variables and is dependent on the depth of the target. The most influential geometric variation involves changes in the relative position of the receiver with respect to the transmitter along the direction of flight; this variable, therefore, requires the highest degree of accuracy. The accuracy required for receiver motions along the vertical direction is roughly one order of magnitude less, and in the lateral direction, several orders of magnitude less. The objective of this paper is to relate the sensitivity of the response to transmitter-receiver geometry to the ability of an airborne, time-domain electromagnetic system to resolve a highly conductive vertical target. This is achieved by a detailed analysis of the effect of the individual x, y, and z distances between the transmitter and the receiver, the transmitter attitude (roll, pitch, and yaw), and transmitter deformation.Sommaire - Les systèmes électromagnétiques en domaine temporel sont particulièrement sensibles aux cibles à forte conductivité durant le temps d’excitation. Les données collectées durant l’émission du transmetteur sont fortement affectées par les relations géométriques entre le transmetteur et le récepteur. Si un facteur de correction n’est pas introduit pour tenir compte de ces variations géométriques, la capacité de ces systèmes à détecter et identifier correctement les cibles fortement conductrices ne peut pas être pleinement réalisée. Les facteurs affectant les positions relatives du transmetteur et du récepteur comprennent les changements de position du récepteur relativement au transmetteur, les changements d’altitude du transmetteur et la déformation de la boucle du transmetteur. Le degré de précision requis pour déterminer la configuration nécesaire pour compenser complètement l‘effet des changements géométriques est différent pour chacune des variables et dépend de la profondeur de la cible. Les changements géométriques qui ont le plus d’influence sont ceux qui font varier la position du récepteur relativement au transmetteur dans l’axe de la ligne de vol; c’est donc cette variable qu’il faut contrôler avec le plus de précision. La précision requise pour le suivi des mouvements du récepteur le long de l’axe vertical est moindre d’environ un ordre de grandeur, tandis que selon l’axe latéral elle est diminuée de plusieurs ordres de grandeur. Le but du présent article est d’établir comment la susceptibilité de la réponse à la géométrie transmetteur-récepteur affecte la capacité d’un système électromagnétique en domaine temporel aéroporté à reconnaître une cible verticale fortement conductrice. Cet objectif est atteint par l’analyse détaillée de l’effet individuel des distances x, y, et z entre le transmetteur et le récepteur, l’attitude du transmetteur (lacet, roulis, tangage) et la déformation du transmetteur."

Jan 1, 2006

By David Humphreys

It is difficult to overstate the importance of China to the future of the world mining and metals industries. In a remarkably short time, China has risen to become the world?s largest producer and consumer of steel and its second largest consumer of non-ferrous metals such as copper and aluminium. It is currently the world?s largest buyer of copper on international markets, the second largest buyer of iron ore, and the third largest buyer of alumina. At the same time, it is the world?s largest or second largest producer and exporter of tin, lead, zinc, magnesium and a host of minor metals and industrial minerals, as well as a fast-growing exporter of coal.

May 1, 2002

By J. A. Finch

"Much progress has been made over the last several years in the ability to measure flotation cell hydrodynamic parameters in both the laboratory and plant. These techniques have allowed fundamental research to proceed to determine the effects that frother chemistry has on the main hydrodynamic parameters (gas hold up, bubble size) as well as on the amount of froth generation and water content of froth. A research program was begun that brought together a team consisting of private companies and a University with expertise in hydrodynamic characterization (McGill), flotation reagent applications (Flottec) and chemical synthesis (Sasol N.A.) with the purpose of characterizing frother chemistries with two goals in mind: Determine which frother chemistry can provide optimized cell hydrodynamics; and, create new frother chemistries with specific hydrodynamic properties.This paper describes the key steps that were taken that led to the development of new frother chemistry for use in flotation.The first step was the characterization of the major frother chemical families in a two phase system. The parameters measured were gas hold up, bubble size, froth height and water carrying rate at different concentrations and gas velocities.Analysis of the data indicated that definite patterns existed between frother chemistry and hydrodynamics and showed that frothers could be grouped into classes. More importantly, by modifying known frothers through chemical reaction it was shown that these frothers could be moved from one class to another. As a result of this better understanding of the interdependence of hydrodynamic and chemical properties, a new frother chemistry was proposed that was predicted to perform similarly to MIBC.The new frother was synthesized and hydrodynamic testing confirmed that the chemical performed similar to MIBC. Laboratory flotation tests were conducted on two different ore types that also confirmed the similar performance of the new chemical and MIBC. Subsequently, the new product was placed on a plant for a short period of time. The results showed that the product was an excellent frother but increased the flotation rate slightly more than MIBC at the same addition rate.Further research showed that the new frother chemistry was a family of products. By changing the reaction the resultant products could be made to be slightly weaker or stronger than MIBC but that this chemistry cannot provide hydrodynamic/froth characteristics similar to strong frothers like glycols and glycol ethers. Further work is planned to conduct longer plant trials to confirm the efficacy of this new frother family."

Jan 1, 2007

By L. Bryson, J. H. W. M. Brits, K. Voogt

"The Anglo American Platinum’s Rustenburg Base Metals Refinery (RBMR) has the world’s first full deposit nickel plating tankhouse. Impurities in the nickel electrolyte can induce stresses in the electrowon nickel deposits that could lead to delamination of the deposit. Identifying the impurities that contribute to increasing internal stresses in the nickel deposit is key to successful operation and automation of the tankhouse. Impurities were introduced in the plant electrolyte and the effects on the full-scale nickel deposits evaluated. The impurity-adjusted electrolyte solutions were also analyzed using commercially available bench-scale methods to determine the induced stress. A correlation between impurity-induced deposit stress and full-scale delamination was developed. A direct correlation can now be made between feed quality, i.e. impurity concentrations, and degree of delamination in the plant. This methodology has the potential to rapidly predict the effect of new reagents, upstream process upset conditions and synergistic interactions between impurities on deposit stress and delamination of nickel deposits.INTRODUCTION Nickel electrowinning in sulphate media was first pioneered by Outokumpu in its Harjavalta refinery in 1960 (Saarinen and Seilo, 1985). The original process was very manual with starter sheets plated onto “acid resistant” steel for 36 hours and then manually stripped and cut into sheets which could be inserted into the main production cells for a further 4–5 days. The starter sheet stripping and manufacture process was later automated. The same technology was subsequently implemented on a number of plants around the world. Anglo American Platinum’s Base Metal Refinery (BMR) began nickel electrowinning in the early 1980’s. The recent expansion of Anglo American Platinum’s Base Metals Refinery necessitated the construction of a new nickel tankhouse to achieve two primary objectives. The first to increase the capacity to 32 400 tpa nickel and the second to reduce employee occupational exposure to nickel aerosols. The new tankhouse has been commissioned and is in the process of ramp-up; more details are given by Hagemann et al. (2016). Fundamental to lowering employee exposure to aerosols was automating both harvesting and final handling of cathode. In order to accomplish this a bold move was taken to plate up to 10 days on permanent titanium blanks which are harvested by automatic crane and automatically stripped. The original development work for the plating nickel on titanium blanks over a ten day cycle is given by Bryson et al. (2006)."

Jan 1, 2017

By A. Azad

SAGD (Steam Assisted Gravity Drainage) is an in-situ oil recovery technique for heavy oil reservoirs. The technique has been successfully applied to many projects in the past 25 years and the process has been, now, well understood. It is now believed that geomechanics plays an important role in SAGD and should be considered in numerical or analytical modeling. Currently, geomechanics is numerically modeled through combining a multi-phase flow and a geomechanical simulator. Numerical modeling is, however, time consuming, need lots of input data, and could not be used for quick decision-making purposes. To decrease the modeling time, this study based on a new version of the Reis drainage model, proposes coupled mathematical model and reserves the effect of geomechanics in the process. Results showed a perfect match with the past experimental and numerical data.

May 1, 2009

By V I. McCallum

In 1954, Falconbridge Nickel Mines Limited began the program of deepening the Falconbridge mine workings for 2,000 feet below the bottom, or 4025, level in order to provide twelve new levels for production. Involved in this program were a production-sized internal shaft, .crushing, pumping and hoisting installations, the integration of the new shaft operations with those of existing shafts, and considerations of ventilation requirements and ground support at depth. This paper describes the major items of equipment, and the depth development of No. 9 shaft as a whole, and also emphasize the planning phases of the program. The factors involved and reasons for the equipment and layouts chosen are given. Introduction and History THIS paper describes the planning and development of that portion of the Falconbridge mine between the 4025 and 6050 mining levels. This mine, the oldest of several being operated by Falcon-bridge Nickel Mines Limited in the Sudbury district, has been a continuous producer for over thirty years.

Jan 1, 1964

DynoMiner APS Delivery Systems Overview ? New Design of DynoMiner APS-M2 ? Stand alone or attach to Cargo type 10,000 lb (4536 kg) emulsion bins. ? Hose reel w/200-ft (61-m) by 1-inch I.D (25-mm) hose capacity, power rewind. ? Increased water and trace capacity. ? Hose reel and gassing offered as options. ? New Flow Meter ? DN-100: aluminum body, UHMWPE rotors. ? Will be offered as an option. ? APS Nomenclature ? Proposed changes ? DynoMiner APS and APS-M1 to become DynoMiner APS Drifter ? DynoMiner APS-M2 to become DynoMiner APS Stoper. ? Both to have optional gassing / flow metering.

May 1, 2004

By P. P. Andrieux

The recovery of the Zone G crown pillar, located between the bottom of the open pit and the top of the underground workings at the Raglan Katinniq Mine in Nunavik, started in the summer of 2008 and should be completed by the end of 2009. This article describes the rock mechanics-based approach implemented to design the recovery of this valuable block of ore. The stereophotography-based ShapeMetriX3D technique was first used to provide a comprehensive assessment of the various joint sets that comprised the pillar. Then, the statistical distributions obtained for the dip, dip direction, spacing and persistence of these sets were used in conjunction with the geometry of the large-scale faults present in the area to build and run a series of explicit rigid numerical models. Each of these models had a slightly different jointing geometry, randomly constructed from these statistical distributions. Incorporating in a properly formulated numerical model the variability of some of the input parameters has allowed the engineering team to assess in a rational and reliable manner the likelihood of success of the proposed mining method and sequence.

May 1, 2009

By Tatiana Ravani von Ow, Leandro Bomvisinho

"The size of mills driven by ring-gear or by a gearless solution has significantly increased in the last years. This has created additional challenges for the driven equipment. The requirements for the mechanical devices and the power grid have become more demanding. Controlled soft starting and operation, especially in dual pinion mills, as well as the protection of the equipment has gained importance. The selection of the drive solution for the mill therefore becomes more critical. Besides the classical criteria such as performance, efficiency and capital costs other factors come in the evaluation of the system such as flexibility and optimization of operation, reliability and the ageing of the grinding equipment.Variable speed solutions offer significant advantages over conventional fixed speed drives due to their application specific features and process optimization capabilities, even for ball mills where these are not seen yet as a must.The initial capital costs are higher than some of the direct on-line solutions however the benefits for the operation during the lifetime of the mill generated by the use of converter solutions justify the additional higher investment.INTRODUCTIONThe method of powering mills such as AG, SAG and Ball has a long and technically interesting history. It can be said; almost every decade in the last half century had its own trend. The trend was dominated by the market demand, by the process development and requirement of the mechanical and the electrical technology but mostly by the price of the applied technology.All has started about 50 years ago with mill diameters less than 20 feet driven by fix speed synchronous or wound rotor motors with the power of about 2 MW. Around 10 years later, the mill sizes increased, but the necessary torque could not be transmitted by one pinion therefore dual pinion solutions were developed to power the mills. However, realization of the dual pinion solution was only possible when load could be evenly shared between the two pinions."

Jan 1, 2010

By T. G. Joseph

A strain-softening constitutive relationship is introduced that describes the post-failure stress-strain curve for rock regardless of whether the rock is intact or broken. The core of this relationship is an ?apparent friction? concept that relates the post-failure apparent cohesive and frictional characteristics of the rock to the strain. The relationship can be determined for a given rock via a series of tri-axial strength tests establishing the peak strength and corresponding strain for a range of confining pressures, together with the determination of the base angle of friction via a simple tilt test. The postulates and assumptions used in deriving this relationship are verified from results of tri-axial tests on both intact and broken rock.

May 1, 2002

By Jean-Claude LeRoy, Herman Keller

"INTRODUCTIONEROCON's work is the reclamation of mine wastelands. It has had considerable experience in particular in the reclamation of gold mine tailings in the Canadian Shield since the latter part of the sixties when most gold mines were closing down.A typical example is the famous Hollinger Mine in Timmins which produced $566 million worth of metal from 1910 to 1968 and had left behind some 56 million tons of tailings covering about 1,000 acres which were reclaimed on very short order and are now lush meadows of agricultural quality.To date, practically all gold mine tailings have been reclaimed once and for all by establishing a permanent, self-sustaining and maintenance free vegetation cover.RECLAMATION & THE MINING TOWNSThe first appreciation of people in a mining community where the tailings have been revegetated will be noticing one day the elimination of dusty conditions that used to arise formerly on every dry and windy day. In that respect, EROCON encourages not only vegetating the tailings but also the immediate surroundings of the mills and plants themselves at active mines. The elimination of windborne dust will result in an appreciable decrease in maintenance costs of plant and machinery and more pleasant working conditions for all."

Jan 1, 1975

By Scott G. Honan, Wayne F. Luinstra

"Since 1992, the concentration of gold using gravity methods has progressed to become an important part of production at Hemlo Gold's Golden Giant Mine. Currently, the gravity circuit accounts for approximately 25% of the Golden Giant Mine's Gold production. This circuit consists of a 30 inch Center-Drain Knelson Concentrator and a Shaking Table. The evolution of gravity concentration will be discussed with an emphasis on the economic justification for a gravity circuit as well as the practical aspects and metallurgical impact of operating such a circuit. It will be demonstrated that the operation of a gravity circuit has definite benefits to the operation of the Golden Giant Mill and will continue to play an important role in future gold production.1.0 IntroductionHemlo Gold Mines Inc. Golden Giant Mine is a 3000 TPD underground gold mine and milling facility located 40 km east of Marathon, Ontario. Mining is accomplished by means of sublevel longhole open stoping. The ore is processed using conventional crushing, 3-stage ball milling, conventional cyanidation and CIP processes. The mill and concentrator are described in more detail in other publications1,2.Since July of 1992, the Golden Giant Mine has been using a gravity circuit for gold recovery in the mill's grinding circuit. Despite the fact that gold recovery averages over 96% using conventional cyanidation and carbon-in-pulp processes, the gravity circuit has become an integral part of milling operations. This paper will discuss the economic justification for a gravity circuit as well as the practical and metallurgical aspects of its operation."

Jan 1, 1996

By Markus Timusk

This paper describes a research project that focuses on developing a diagnostic routine to assist in decision support for the condition based maintenance of mobile mining equipment subject to unsteady duty. The objective is to develop a general method for initial identification of mechanical faults in machinery operating under non-steady state conditions. The platform to be used for the experimental development and validation of the system is the swing machinery in an electric mining shovel operating in an open pit mining environment. The strategic approach that is proposed for the diagnostic routine will involve using novelty detection augmented by temporal classification.

May 1, 2004

By Chuan-liu Wang

The bionic non-smooth surface has the characteristics of anti-wear, and reducing resistance. Based on bionic non-smooth surface?s characteristics, a bionic drill bit was developed. When the bionic drill bit is used, a bionic non-smooth surface forms on the crown of bionic drill bit. This surface can be used to extend the life of drill bit and improve drill efficiency. The bionic unit diameter and arrangement were researched in this paper to determine the optimal bionic non-smooth surface for further improving the life and efficiency of drill bit. Four bionic samples having the same structure size, materials and arrangement were designed and manufactured. After being sintered, the abrasion ratios of the four bionic samples were tested, and the results show that the abrasion ratio of Nos. 3 and 2 were similar (only 2% difference) and higher than that of No. 1 and 4. Therefore, the optimal diameter of bionic unit is 1.5 and 2.0 mm. Small diameter bionic drill bits were designed and manufactured, and tested in the laboratory. The results show that not all bionic structure bodies are better than normal diamond bits, except the bionic unit arranged in a reasonable range. When the angle was 24° and 30°, the arrangement of bionic unit were more reasonable, which shows the superiority of the bionic coupling bit.

Aug 1, 2013