Search Documents

Purification of Nickel and Cobalt from Heap Leaching Effluents Using Ion Exchange Resins A comparative study among several chelating resins for purification of a heap leaching effluent from a nickel laterite ore has been finished. Chelating resins with iminodiacetate (IDA) and bis-picolylamine (Bis-PA) functional groups, from different suppliers, have been evaluated for their selectivity and loading capacities for nickel and cobalt over impurities. The two evaluated IDA resins, Amberlite IRC 748 and Monoplus TP 207, showed very similar results for both loading capacity and selectivity. Better performance was obtained at 7 BV/h at a pH of 4. Evaluation of Bis-PA resin showed that XUS 43578 has better performance than TP 220, with a 30 per cent higher loading capacity and superior selectivity for nickel over impurities.

Sep 13, 2010

Mineralogical analysis of a nickeliferous laterite from the Rockhampton region shows that the nickel is largely associated with the manganese wad and opaline silica. The laterite also contains an appreciable chromite content (about 12 per cent Cr2O,) although this tends to be poorly liberated.Leaching with hydrochloric or sulphuric acid, at atmospheric pressure at the boiling point is non-selective with respect to iron dissolution.The degree of dissolution increases as the acid concentration and retention time are increased; cobalt dissolution requires less aggressive conditions than does the dissolution of an equivalent amount of nickel.Leaching with sulphuric acid at elevated temperatures and pressures leads to a minimum amount of iron dissolution, is rapid, and requires a reduced acid addition rate. Nickel and cobalt recovery from the clarified leachate would be simplified because of the leach selectivity.Pressure leaching appears to be the most practical route for treating the Rockhampton laterite. The economics of processing would be made more attractive by the recovery of a chromium concentrate from the leach residue. This would typically contain about 45 per cent Cr2O, and could be used as a source of chromium chemicals.

Jan 1, 1986

By R L. Brathwaite

Previous paleodepth studies of low-sulphidation epithermal Au-Ag deposits in the Coromandel region indicated that economic gold mineralisation was generally limited to a depth zone of 100 to 400 m below the paleosurface. Notable exceptions are Waihi and Karangahake, where ore shoots extended to depths of about 750 and 900 m respectively. These studies have been extended to include Au-Ag, Hg and Sb epithermal deposits in Northland and the Taupo Volcanic Zone. The main paleodepth indicators used are sinters and hydrothermal eruption breccias, hydrostatic pressures estimated from homogenisation temperature measurements on fluid inclusions, and hydrothermal alteration mineralogy. Also the occurrence of lacustrine and fluvial sediments is an indicator of the paleosurface at their time of deposition. Selected paleodepth indicators have been compiled and mapped in a GIS environment. The distribution of the paleodepth indicators are used to define regional variations in erosion levels, and may be useful in predicting areas most likely to preserve the optimum depth window for gold deposition. In the Coromandel region, regional stream sediment geochemical data has also been used to broadly define erosion levels in terms of Zn, Pb and Cu representing deeper base metal zone mineralization and Hg and Sb representing shallower cinnabar and stibnite mineralisation. The interpretations of paleodepth and potential reconstruction of paleosurfaces are limited by the paucity of data, poor age control on the paleodepth indicators and the epithermal deposits, and marked relief and complex stratigraphy in the volcanic terranes.

Jan 1, 2003

The mineralogy of nickel slags from the flash smelter of Western Mining Corporation Ltd. at Kalgoorlie was studied. Residual magnesium silicates in the sulphide concentrates raise the melting point of the slag and result in the formation of magnesium-rich olivines. Addition of lime lowered the melting point, and, in slowly cooled slags, resulted in the formation of a pyroxene.Magnetite and sulphides were also present in all slags.The converter slags contained an olivine near fayalite in composition, together with wiistite, magnetite, and a little sulphide.Accretions from the hearth of the flash furnace were largely composed of magnetite with subsidiary olivine similar in composition to those of the flash furnace slags.Wall deposits, however, were largely composed of nickel ferrite and nickel-iron olivines.

Jan 1, 1976

By Clarke DS

The igneous intrusions in SE Papua New Guinea are part of a sub-volcanic to plutonic, high-K calc-alkaline to shoshonitic suite. High-K andesitic to dacitic intrusives on Misima and Woodlark Islands, and shoshonitic intrusives in Milne Bay and the eastern Owen Stanley Ranges are related to late Cenozoic andesitic volcanism. Both suites are associated with epithermal Au-Ag deposits and weak porphyry Cu-Au mineralisation. All significant alluvial and lode gold occurrences in the region are spatially related to intrusions. Intrusions in the D'Entrecasteaux Islands and near Mt Suckling are core plutons related to basement doming, and appear to have no association with either volcanism or hydrothermal mineralisation. The core plutons are not petrochemi:ally distinct from the volcano-re:-ed Intrusions.

Jan 1, 1991

Well designed and maintained haul roads are the key to minimising truck haulage on-road hazards and costs, as well as increasing productivity. However, practically designing and managing a haul road for optimal performance is often diff cult to achieve. Poorly designed and built roads exhibit high rolling resistance - a one per cent increase in road rolling resistance can typically reduce speed on ramp by as much as ten per cent - and on the f at by up to 26 per cent. In the current economic climates, investment and operating decisions come under scrutiny. In the long run, this scrutiny returns improved efficiencies and leaner, healthier operations. The focus of this evolving evaluation process should and will certainly fall on haulage operations - simply by virtue of their contribution to overall cost of operations - often in excess of 50 per cent of total costs for deep open-pit mines. Whilst the end result - improved efficiency and reduced cost per ton hauled - is not in itself problematic, it is the route, or process followed to achieve these savings that needs to be carefully managed. We can be guided on this journey by our understanding of how a road is designed, and, critically, the interplay between a good design and safe, cost efficient haulage.This paper brief y summarises the evolution of mine haul road design, from the seminal USBM work of Kaufman and Ault in 1977, through to current geometric, structural, functional and maintenance management design components. These augmented design and management guidelines have been developed over the past decade, both in response to the requirements of mine operators for more safe and efficient haulage systems, and the truck manufacturers' requirements for a more predictable and controlled operating environment. These developments have been paralleled by the need to minimise haulage hazards, both from a health and safety perspective. Generally, both objectives have been achieved, but with some specific areas of design and operation still presenting ongoing potential health and safety hazards.The paper then summarises current design guidelines for these safety-critical issues, both from a road-design 'best-practice' and road management perspectives. Implementation of the approach is seen as a basis for reducing the potential of an under-designed mine road to lead to health and safety defects and secondly as a means of giving haul road safety and performance issues greater prominence in the minds of the road-user, operator, mine planner and designer alike.

Dec 6, 2010

By Parker JB

The Channar Iron Ore Mining Project (the Project) is a joint venture involving the Hamersley Holdings group (Hamersley) and the China Metallurgical Import and Export Corporation (CMIEC). The Project represents the first new iron ore mine development in Australia since 1971/72 and is the first major overseas mining investment by the People's Republic of China (PRC). The Channar mine is being constructed in the Pilbara region of Western Australia and will operate for more than 20 years supplying the PRC with 200 M tonne of high grade iron ore. The Project is configured to take advantage of Hamersley's existing production and support facilities. The Joint Venturers will invest A$280 million to achieve an initial production rate of 3 M tonne/yr and an additional A$120 million over the next 8 years to achieve full capacity of 10 M tonne/yr. Financing the Project to meet the requirements of both Hamersley and CMIEC, with the dependance of the Project on Hamersley's infrastructure, and in a depressed iron ore market, required an innovative financial structure to be arranged in a limited period. This paper describes both the financial structure and its implementation, and draws a number of conclusions regarding the financing of resource projects.

Jan 1, 1989

After a snap-shot survey of water quality of streams draining various coal measures carried out in 2000 - 2001, West Coast Regional Council expanded its monitoring programme to better establish the condition of streams draining coal mining areas and to characterise the variability of water quality with respect to stream flow. Samples were collected for water quality indicators such as pH, sulphate, turbidity, conductivity, temperature and dissolved oxygen as well as macro-invertebrates, fish and assessments of stream habitat. Water quality sampling was carried out at 27 sites on 21 streams located from Page Stream near Seddonville in the north, to Seven Mile Creek near Dunollie in the South, and to Garvey Creek east of Reefton. There was relatively low variability of pH, conductivity and sulphate concentrations at most of the sites sampled. Conductivity and sulphate concentrations reduced with increasing flow and pH generally increased. Significant effects on macro-invertebrate and fish populations were identified at several of the sites where water quality sampling was undertaken. Of the water quality parameters tested, macro-invertebrates were mostly affected by pH. Although not sampled directly (conductivity was used as a surrogate) heavy metal concentration may explain some of the variation in macro-invertebrate communities. Three creeks affected by mine drainage were sampled for fish and no fish were present. Fish appear to be more sensitive to acid rock drainage that invertebrates. Using data from this survey and other studies conducted in the region, the total length of stream that is actually or highly likely to be adversely affected by acid rock drainage was estimated at 125 km. This figure is useful as a gauge as to the magnitude of the issue in this region and for setting of priorities for remediation. However, as it is only an estimate based on limited sampling sites, it should be used with caution.

Jan 1, 2003

By Fogarty J. G H

Ausmelt Technology has a unique capability of removing the impurities, phosphorus and sulphur, from the feed materials to the process. Sulphur is removed to the gas phase almost completely because of the interactions of ore and coal in the reaction region at the top surface of the slag bath. Phosphorus is removed to the slag phase, with both basic and higher, controlled iron oxide levels in slag being achieved in the process. The significance of these features of the process relate to the production of pig iron with very low levels of these impurities for the further processing to steel, and to the treatment of high phosphorus and high sulphur raw materials. The marketability of pig iron and the raw materials are discussed in relation to this feature of Auslron.

Jan 1, 1999

It has long been recognised that Australia can benefit substantially in an economic sense from its rich resource base. The significant resources of the Gippsland Basin are a good example of the wealth of this nation. As cited in popular debate, Australia must value-add to its natural resources to ensure its long term economic prosperity. The significant oil, gas and coal resources of the Gippsland Basin have provided the Strategic Research Foundation with the basis for two major research and development initiatives ensuring the long term economic development of the Basin and Australia. The gas and coal reserves of the Basin together with the area's extensive history in electricity generation provide the rationale for establishing Ceramic Fuel Cells Ltd. A consortium comprising Australia's leading industrialist - BHP, State energy authorities and the Nation's major research and development organisations, has formed Ceramic Fuel Cells to undertake and manage research, development and commercialisation of solid oxide (ceramic) fuel cells which convert fossil fuels directly to electricity with greater efficiency and less pollution than existing technologies. The oil and gas resources of the Basin together with the valuable experience of the operators in recovering these resources, have provided the impetus to investigate the feasibility of a Marine Engineering Research Centre. The commercially oriented research, education and training objectives of the Centre are well supported by the leading industrialists in related industries.

Jan 1, 1992

An optical computing system was used to determine spacings and frequencies in geological fabrics and engineering joint fabrics.Three-dimensional arrays of joints were plotted on an equal-area net. Directions in which true spacings are seen were determined from these plots. Photographs taken along these directions were used for optical computing.

Jan 1, 1970

Knowledge of true block grades is obtained from a mathematical model of an orebody, simulated with sample grades normally distributed and spatially correlated according io a spherical semi-variogram model.The superiority of kriging to the polygonal method of estimation is demonstrated on this modelled deposit by comparing the true values with the kriged and polygonal estimates obtained from sampling the deposit. Finally, selection of blocks of the deposit on the basis of the estimated values, shows that if kriging is used, what is predicted is largely mined, whilst if the polygonal method is used large biases can occur depending on the position of the cut-off grade.

Jan 1, 1978

A GREAT deal of attention has lately been given to the discussion as to the education required for engineers, and especially for mining engineers. The Institute of Civil Engineers has had a committee's report on it which has come to some interesting and valuable conclusions.The Institute of Mining and Metallurgy had a few years back a very long discussion on the subject, and the subject appears to be one of perennial interest to similar societies. Two recent addresses by Prof. Kernot, as president of the Victorian Instituteof Civil Engineers, are among the most interesting and practical of the contributions to the discussion. Engineers seem to feel either that the coming generation has not the same capacity to benefit by the training that has made themselves what they are, or that such training has turned out in themselves inefficient men, and that they must consequently struggle to obtain a better one for their successors. For not only is there a desire to extend existing instruction to cover the advances of science, but there seems to be a general desire also to make a completely radical change in the methods.It is not necessary to observe that education does not mean the imparting and acquiring of information, but rather the cultivation of the faculties so that the best use can be made of them and of any information acquired. For instance, a man is not educated who has by heart his lectures and the contents of his text-books, but that man is who remembers little of the actual wording of his text-books, but is able to find anything required in them...

Jan 1, 1909

Judicious placement of a range of geotechnical instruments was employed at the Tasmania gold mine, Beaconsfield, Tasmania, as a key strategy in the monitoring of rock mass conditions over the past four years. The range of instruments employed included vibrating wire stress-meters and hollow inclusion cells to monitor changing stress conditions, resistance wire and multipoint borehole extensometers to monitor the impact of stress changes on the integrity of the rock mass, and instrumented cable bolts and threadbar bolts to monitor the static and dynamic impact of rock mass changes on the installed ground control system. Initially the monitoring was of a qualitative nature, monitoring change from the time of installation. The value of the output was considerable when considered in relation to the ongoing seismic record which was also being monitored. It was clear from the seismic record and the monitoring results that stope blasting was the primary trigger for changing rock mass conditions. However, it was unclear how well observed behaviour was reflecting conditions anticipated by elastic numerical modelling. The latter had predicted significant stress increase in the near field of man-access footwall development. Qualitative monitoring and visual inspection did not support the modelling prediction, and this led to a program of quantitative measurement being undertaken. Measurement of the absolute stress condition in the backs of footwall development immediately adjacent to monitoring hollow inclusion cells provided the benchmark for tracking quantitative stress change. The program provided insight into the evolution of principal stress field magnitude and orientation in relation to rock mass change observed with extensometers and instrumented ground control elements, as well as providing a degree of calibration between the elastic numerical modelling and the virgin stress field. Calibrated monitoring data has also provided a useful benchmark for finite element modelling which is to be used for future mine-wide design.

Nov 25, 2010

The changes in layout and design over 48 years, from the first crushing and shiploading plant installed at Whyalla in 1915, up to the present plant being built at Koolan Island, Yampi Sound may be summarized as follows.1. Smaller motors and lower power consumption have resulted froma. oil lubrication, where practicable, in place of grease,b. a high pressure "oil-lift" device to reduce starting torque in crushers with white metal bearings, andc. roller bearings in place of white metal.2. Short centre drives with pivot-based motors permit controlled loads on bearings and a reduction in size of crusher houses and motor rooms.3. Dust proofing and pressurising of crusher houses and motor rooms reduces working temperatures and improves cleanliness.4. Variable speed pan feeders give improved plant control, with the use of one man only, and remove the need for large surge bins between crushing stages.5. The use of diesel quarry trucks to dump ore through a "drive over"tip results in faster truck cycles.6. Elevated cylindrical silos with air operated chutes, replace long horizontal storage bins with multiple manually operated side discharge chutes for loading rail cars, and give faster and more accurate truck loading. The silos are charged by belt conveyors with automatic distributors.7. Increased shipping bin capacity (40,000 tons at Whyalla and 6O,OOO tons being built at Koolan Island) caters for the bigger vessels now in use and envisaged for the future. Automatic travelling distributors deliver ore to the bins in layers to ensure, maximum mixing and a more uniform grade for blast furnaces.INTRODUCTIONThe Broken Hill Proprietary Company Ltd has six major crushing plants in Australia at its principal sources of raw material. These are at Iron Knob bench G, Iron Knob scree ore plant, Iron Baron, and Cockatoo Island, all of which are ironstone operations. The other two plants are at Rapid Bay, a limestone quarry, and at Ardrossan, which is the Company's only source of dolomite.

Jan 1, 1963

In addressing the need for non-degree tertiary training, let us examine some recent reviews of engineering and geoscience education. The Finniston Report (1) criticised the formation of engineers in the UK and stated that this was largely due to the narrow British conception of engineering as a branch of applied science which militates against an effective marriage between theory and application. It also criticised the system for not giving students sufficient grounding in the synthesis of technical, human and financial considerations within their undergraduate courses. As we all know, this report has led to the restructuring of engineering education in the UK. More recently, a Review of the Discipline of Engineering was carried out in Australia by a committee chaired by Professor Sir Bruce Williams (2). The report stated that: Australia has a fairly good system of engineering education that should be made better. more should be done to develop the communication skills of both staff and students. more attention should be paid to changes in engineering practice and the human element in technology. there is a serious shortage of state of the art equipment in most engineering schools. female enrolments in engineering courses should be increased from the current level of about 7% to 20% by 1997. employers should develop a better understanding of the need for continuing education. staff in engineering schools should develop closer relations with employers of engineers. higher education institutions with engineering schools should give financial and other inducements to staff to increase the proportion of study leave or professional development leave spent working as engineers in the business sector. there is considerable room for improvements in the teaching process and in the development of evaluation schemes for assessing the teaching contributions of staff. In its recent report to the Council of the Institution of Engineers, Australia, the Task Force on Engineering Education(3) makes the following points: managerial, entrepreneurial, professional and interpersonal skills should be introduced and integrated into the undergraduate courses but studied in depth as part of continuing education. the continuing education policy of the Institution should be promoted and strengthened with all engineers required to pursue continuing education. the Institution should develop a comprehensive guide to continuing education available from universities, colleges and other public and private sector organisations.

Jan 1, 1989

THE object of the present paper is to give a brief description of the metallurgical process followed by the Grand Junction Co, and the results obtained therefrom. All figures quoted are from the actual working of the plant over a period of six months from January to June, 1910. The short ton of 2000 lb. is used by the company. Its gold is valued at 84s. per oz. fine, silver at 2s. per oz. fine. The ore consists essentially of a gangue of quartz and calcite, with 8 to 10%sulphide-pyrite, sphalerite, galena, chalcopyrite, and traces of arsenic and antimony. The colmtry-rock is a highlyaltered dacite. Small stringers of highly-mineralized ore penetrate the footwall of some of the lodes, forming a valuable stockwerk up to 3 ft. in thickness. In stoping, this is mined with the well defined lode, thus bringing into the mill at times a considerable quantity of hard country-rock. The gold exists in an exceedingly fine state of division, consequently rendering it necessary to grind very fine to obtain a satisfactory extraction.

Jan 1, 1912

The Government signalled its intention in the Economic Statement on 17 December 1987 to improve the fairness of the taxation system and to facilitate the process of economic adjustment by: removing tax concessions that benefit some taxpayers at the expense of other taxpayers,ensuring that those who can afford it shoulder their fair share of the tax burden,securing a revenue base which will provide sufficient resources to maintain effective social services,reducing artificial protection and concessions that discriminate against some sectors, and encouraging confidence through an economic environment with a medium-term orientation. The Government has clearly stated to all sectors that tax preferences will be phased out and businesses need to look inwardly to their investment policies if they are to survive in an open economy. This paper will address the effect of these Government objectives on the taxation structure for all forms of mineral exploration in New Zealand. The present tax structure will firstly be analysed, in particular setting out the tax advantages available to the industry. The effect of changes to the tax system within the recent past which relate to mineral exploration will then be examined. Finally the paper will address the question of possible future changes, particularly in the light of Government's intention to move towards a tax system which does not provide an advantage for any one sector of the economy.

Jan 1, 1988

An intensely sheared and mineralized zone occurs in the quartz dolerite greenstone (or younger greenstone) mass on the western limb of the Kalgoorlie syncline. This zone comprises the western part of the Golden Mile and has produced the greater part of the 33,000,000 oz of gold produced to date from the main mining belts. A study of the general geological and structural features suggests that the lode shear system will continue southward on a pitch similar to that of the main syncline. Although payable ore has been found recently further to the south, the expectation of large quantities extending southward from the present mining areas is problematical.INTRODUCTIONUntil the late 1930's the principal mining activities in the western lode system were centred on three major ore-shoots formed on the No. 4, No. 3 and to a lesser extent on the No. 2 lode shears (Fig. 1). With the gradual reduction of grade in depth on these main ore shoots, increasing attention was paid to the "Minor Lode" system of lode shears known to exist in the same area. A large quantity of payable ore was found on these "Minor Lodes" particularly in the central part of the mining area. In recent years more attention has been given to exploration in a southerly direction.ROCK TYPES AND STRUCTURESThe western system occurs on the western flank of a dragfolded, south pitching syncline. The rock succession consists of Black Flag sediments overlying the younger greenstone horizon which overlies the fine grained older greenstone horizon. The axis of the syncline is regarded as a tight infold of the overlying Black Flag sediments. This infold has been faulted and intruded by albite porphyry resulting in the formation of a composite body of slates...

Jan 1, 1964

By Greenwood J. N

This work was commenced at a time when information on the manufacture of cemented tungsten carbide was urgently needed in Australia. Much information of a general type has been published, but many of the details of the processes used are still undisclosed. The aim of this research was to determine a satisfactory way in which cemented tungsten carbide could, be made, and to investigate the problems which are associated with the process. As the work proceeded, its ramifications grew continually, and it was necessary to limit the possible lines of investigation. After much experimental work, a 9% cobalt-tungsten carbide alloy was developed which had satisfactory properties when used as a cutting tip. The effect of certain variables on the properties of this particular alloy was investigated.The tungsten carbide was prepared in stages from King Island scheelite concentrates under strict laboratory control, whilst the cobalt (1) used was made from cobalt oxide prepared from crude cobalt oxide obtained from Eisdon.In order to clarify the detailed experimental work, a brief summary of the method used for the preparation of cemented tungsten carbide follows.Tungsten carbide and cobalt are prepared in a very finely powdered state, and are then thor,oughly mixed by a ball milling operation. The resultant mixture is pressed in a suitably shaped die into small compacts which are subsequently '''presintered,'' i.e., heated' in hydrogen between 800°C. and 1000°C. The final sintering is carried out in hydrogen between 1,400°C.and 1,600°C. for about half an hour. These "alloys" may contain from 3 to 13% cobalt, depending on the particular properties required of them.PREPARATION OF MATERIALSThe tungsten oxide prepared as described by Smithells (2) was extremely finely divided, and after a few hours' grinding in a ball mill, the powder consisted of material below 10 microns iJ;l size. The oxide was reduced to tungsten metal with hydrogen in a tube furnace. The reduction was carried out at 800-900° C., a rapid flow of hydrogen being maintained in order to remove the water vapour' formed as a result of the reactions:

Jan 1, 1942