Search Documents

By N. A. D. Parlee, I. D. Shah, W. C. Phelps

THIS note reports on a continuation of a program on the thermodynamics of Fe-S-X systems in the "steel-burning" temperature range begun by Bock, Barloga, and parlee.' Small coils of 0.039-in.-diameter pure iron (Ferrovac-E) wire were equilibrated with Fe-S-0 melts in ingot iron crucibles under argon at 1324°C in the assembly shown in Fig. 1, the lower part of which was heated in a large Globar furnace. Fig. 1 shows (R) the coiled iron wire sample, (M) the Fe-S-0 melt prepared from desired proportions of ferrous sulfide and ferric oxide, (K) the iron crucible, (I) a mullite guide tube, (J) an alumina crucible, (L) alundum sand, (N) crushed mullite, (Q) hollow cylinders of K30 brick, (C) a steel rod, (B), (El, (F), (G), (P), and (O), details of brass water-cooled head, and (H) a mullite tube 2-3/4 in. ID and 26 in. long. The rod (C) bearing the sample could be removed at will and be replaced by a tube for sampling the melt, or by a thermocouple for comparing the melt temperature with a control thermocouple not far from the 2-3/4-in. mullite tube. After equilibration the iron coils were treated with acid to remove the outer layer of metal and then they were analyzed for sulfur by a standard combustion method. The melt samples were analyzed for oxygen by a variation of Lander's2 hydrogen-reduction method for mattes, and for sulfur by the ASTM combustion-iodometric method NO. E 30-47. When the results of some forty-two runs were examined it was found that the sulfur and oxygen contents of the equilibrated melts showed good consistency, in that the plotted compositions fell along the smooth curve shown in Fig. 2. The points on this curve represent the experimental compositions of melts in equilibrium with ?-iron (Fe-S-0) solid solutions. These solid solutions are saturated with sulfur and oxygen with respect to the melt and therefore have the same sulfur and oxygen activities as the melt. The curve drawn through the points therefore delineates the ? liquidus. It falls in such a position as to roughly confirm the liquidus curves of Hilty and crafts3 at 1200" and 1300°C which are

Jan 1, 1965

By P. J. Potter

Practically all tin-base babbitt metals used in engine bearings are made to customers' specifications, which are many and varied. The copper ranges from 3 to 8 per cent. and the antimony from 4 to 13 per cent.; generally, the babbitt with lower copper content will contain from 4 to 8 per cent. antimony and that with higher copper will have from 7 to 13 per cent. antimony. The allowable lead content varies from 0.20 to 2.00 per cent. If a solder is used as a bonding material instead of tin, the resulting material in the finished bearing will have a higher lead content, but it would not be enough to bring the lead above specifica-tional limits. Impurities such as iron, arsenic and bismuth should be determined in the tin before using to insure a uniform and high-grade product. These points must be considered when segregating and grading the waste that comes from the finishing operations on lined bearings. Classification of SCRAP Because of the extremely rigid nature of most of the specifications for bearing linings it is necessary to use the purest of materials as a base for all compositions. The problem of handling secondary metals is confined almost entirely to the recovery of drosses, spills and turnings incident to the manufacturing operations. As a matter of convenience the waste or scrap may be divided into 10 grades, as follows: 1. Tin from pots where tinning operation is carried out. 2. Tin and babbitt spatters from babbitting operation. - 3. Tin skimmings combined with burned zinc chloride. 4. Borings and reamings. 5. Gates from die-cast bushings and bearings. 6. Drosses from die-cast pots, babbitt foundry pots, and pots in babbittiug room. 7. Babbitt with small amount of bronze from machining operations. 8. Babbitt and bronze borings. 9. Scrap bronze-back babbitt-lined bearings. I 10. Scrap die-cast bearings and bushings. A few of these grades of salvaged material have compositions that make it possible to determine beforehand where they may be used to

Jan 1, 1930

By W. Lawrence Austin

Jan 1, 1884

By W. A. Burns

Vertical flow is an important mechanism in many petroleum reservoirs. Yet no adequate method has heretofore been proposed for determining the in-situ vertical permeability in a reasonable length of time. Core measurements of vertical permeability do not necessarily represent effective in-situ values. Cores may be representative of only localized pockets of high or low permeability, and total reliance on cores might cause one to overlook the presence of vertical fractures altogether. Conventional single-well tests, interference tests, and pulse tests commonly are used to determine horizontal transmissibility, khh/u, but generally are not designed to measure vertical trans-missibility or other groups containing vertical permeability, ku. A new well test described here provides a measure of in-situ vertical permeability as well as the previously measurable horizontal permeability. This "vertical test" determines the vertical diffusivity, kv/gcu, and horizontal transmissibility, khd1/u (where dl is the length of injection or production perforations). The test is basically a short-term interference or pulse test normally lasting less than a day. Conventional down-hole equipment is used between two isolated sets of perforations in the same well, as shown in Fig. 1. A "layer-cake" description of a reservoir can be obtained by running two or more vertical tests in the same well, each over different vertical intervals. Each test can be analyzed for the effective vertical and horizontal properties of the interval tested. In addition, a vertical well test can determine the effective- ness of a shale barrier or tight zone by testing across it. Field use to date of vertical testing has confirmed its utility in reservoir description. Mathematical Basis Interpretation of vertical tests for ku and kh is based on comparison of measured pressure response with computer-generated response. Pressure behavior during a vertical test in a homogeneous, anisotropic, infinite-acting reservoir (infinite in radial extent and bounded in both directions vertically) is given by the diffusion equation for slightly compressible fluids with negligible gravity effects.l A schematic diagram of the problem is presented in Fig. 2, and an analytic solution, based on the image

Jan 1, 1970

By Open-Hearth Steel

I received a telegram yesterday from Mr. J. H. Nead saying that he regretted circumstances had come up which prevent his attending the meeting, but that arrangements have been made and Mr. T. S. Washburn, of Inland Steel, will act as the Co-Chairman in his stead. We are sorry, of course, that he cannot be here at this conference. We have, therefore, asked Mr. James J. Bowden, chief metallurgist of Republic Steel Corporation, Cleveland, to act as Chairman and Mr. Tom Washburn to act as Co-Chairman. I will turn the meeting over to these gentlemen at this time.

Jan 1, 1940

By E. F. Johnson, V. O. Naumann, D. P. Bossler

A method is presented for calculating individual gas and oil or water and oil relative permeabilities from data obtained during a gas drive or a waterflood experiment performed on a linear porous body. The method has been tested and found both rapid and reliable for normal-sized core samples. INTRODUCTION Individual oil and gas or oil and water relative permeabilities are required for a number of reservoir engineering applications. Chief among these is the evaluation of oil displacement under conditions where gravitational effects are significant, such as a water drive or crestal gas injection in a steeply dipping oil reservoir. Numerous proposed methods of obtaining relative permeability data on reservoir core samples have been too tedious and time consuming for practical use, or have yielded questionable and sometimes inconsistent results. A method has been developed by which the individual relative permeability curves can be calculated from data collected during a displacement test. The method is based on sound theoretical considerations. Using this method, with a properly designed experimental procedure, relative permeability curves can be obtained using core samples of normal size (i.e., 2 to 3 in. in length and 1 to 2 in. in diameter) within a few days after receipt of the core. In a recent publication D. A. Efros1 describes an approach to the calculation of individual relative permeabilities that is based on the same theoretical considerations. We believe the approach described in the present paper is more adaptable to practical application than the method implied by Efros. In addition, comparisons with independently determined relative permeabilities are furnished to substantiate the reliability of the new method. DERIVATION Previously the theory of Buckley and Leverett as extended by Welge2 as been used to calculate the ratio of relative permeabilities. In the derivation which follows, this theory is further extended to permit calculation of the individual relative permeabilities. The theory assumes two conditions which must be achieved before the method is applicable. They are that the flow velocity be high enough to achieve what has been termed stabilized displacement,3 and that the flow velocity is constant at all cross sections of the linear porous body. In stabilized displacement the flowing pressure gradient is high compared with the capillary pressure difference between the flowing phases. The high pressure drop insures that the portion of the core in which capillary effects predominate will be compressed to a negligibly small fraction of the total pore space. The assumption of constant flow velocity at all

By E. Northcott, I. M. LeBaron

Before describing the electrostatic processing of feldspar, it might be well to review some of the basic definitions and terminology of feldspars. The feldspar minerals constitute a group of alumino-silicates of potassium, sodium, and calcium. Barium feldspar sometimes occurs naturally but is very rare. Hardness varies between 6 and 6.5 and specific gravity between 2.5 and 2.8. Color is generally white or pale shades of red, yellow, or green. The approximate chemical composition of the principal feldspars is given in Table I. The albite (sodium aluminum silicate) and an-

Jan 1, 1959

By C. S. Samis, D. P. Seraphim

In the presence of oxygen, galena is oxidized in an aqueous medium containing ammonium acetate in accordance with the following reaction: PbS + 1/2 0, + 2 NH~Ac -» PbAc, + So + 2 NH: + H2O. This reaction was studied in an autoclave under oxygen pressure by polarographic measurement of the concentration of lead ion in solution. Oxidation rate is parabolic. The reaction products are lead acetote and elemental sulfur, the latter forming a film on the galena crystal. Reaction kinetics appear to be determined by the diffusion of lead from the galena phase to the solution interface through the film of sulfur. RECENT applications of pressure leaching on a commercial scale have emphasized the metallurgical importance of the oxidation of sulfide minerals in aqueous media by oxygen under pressure. Research experience has shown that sulfates, thio-nates, and metal oxides are the products of humid oxidation of sulfide minerals in basic solutions. The metal oxides may be solubilized in the presence of a complexing ion.' Certain oxide minerals are also amenable to treatment by this type of oxidation.' Several kinetic studies have been made of reactions of this type. Stenhouse' found that pyrite (FeS?) oxidized in a sodium hydroxide solution to produce a soluble sulfate and an insoluble layer of iron oxide and that the kinetics of the reaction were controlled by oxygen diffusion through the oxide layer. Andersen' studied the oxidation of galena (PbS) in a sodium hydroxide solution under oxygen pressure. He found the lead and sulfur to be simultaneously oxidized to produce plum bite ions and sulfate ions, and that the reaction rate was proportional to the surface area of the galena. The kinetics appeared to be determined by the reaction of oxygen and water with the galena surface. In each of the above reactions the metal and sulfur components of the mineral were oxidized simultaneously and at equal rates. In the present study the alkaline medium has been replaced by an approximately neutral solution of ammonium acetate in which lead sulfate is soluble. Under the conditions no sulfate was produced and no sulfur could be detected in the solution. The metal component of the mineral was solubilized and the liberated sulfur remained as a film of elemental sulfur on the surface of the galena crystal. A kinetic study of this reaction was undertaken to establish the kinetic mechanism and to determine the rate controlling step. Specific reaction rates were determined by oxidizing crystals of galena of measured surface areas in an autoclave maintained at the desired temperature and oxygen pressure. The rate of reaction was followed by measuring the concentration of lead in the ammonium acetate solution with a cathode ray polarograph, employing stationary platinum electrodes incorporated in the autoclave. Experimental Materials and Equipment Crystals of galena obtained from Violamac Mines, Retallack, B. C., were selected for oxidation because

Jan 1, 1957

By Donald J. Knight

HEAT Treatment at 1500' F of a mild steel containing 0.1 pct C, in an atmosphere which is oxidizing to both carbon and iron, results in the progressive oxidation of the metal surface with little or no change in the carbon content of the underlying metal. Further heat treatment of the scaled metal in either a neutral atmosphere or in a vacuum may or may not result in the decarburization of the metal depending upon the physical nature of the scale. It is apparent that if a continuous layer of oxide is present on the steel surface, the reaction OScale + Cmetal Cogas cannot progress since the SO formed gas would be unable to leave the oxide/metal interface. Thus, in order for the reaction to progress, the oxide must be cracked or porous. Vacuum heat treatment at 1500" F of samples with a thick continuous oxide scale showed no decarburization of the steel. However, when cracks were introduced mechanically into the scale prior to the vacuum heat treatment notable decarburization of the metal resulted and a structure as shown by Fig. 1 obtained, i.e., reduction of the crack walls to ferrite. With reference to the diagram of Fig. 2, it would appear that a mechanism of the following type takes place. Carbon atoms arriving at an oxide/metal/void interface, such as 'A', Fig. 2(a), can combine with oxygen atoms from the scale and leave the reaction site as Cogas thereby reducing the oxide to metal. On a greatly magnified scale, Fig. 2(b),this will appear as a ferrite projection along the crack wall. Carbon atoms entering this projection can react with oxygen atoms at point 'C', which is a new interface, and so on leading to a progressive growth of the ferrite along the crack wall and to the surface, Figs. 2 (c) and 1. It would appear that the only means by which thickening of the ferrite film can take place is by a diffusion of oxygen through the ferrite film to react with carbon at the newly formed ferrite/ void interface. Since the diffusion rate of carbon is reportedly much greater than that of oxygen, and since there is a low probability factor of oxygen and carbon atoms arriving simultaneously at the same site on the ferritehoid interface, there will be a tendency for more rapid lengthening than thickening of the ferrite layer, as is observed.

Jan 1, 1962

By Frederick Laist

AFTER a series of experiments covering a period of about three years, ending from the spring of 19iJ.2 to the spring of 1915, a 2,000-ton leaching plant for the treatment of the accumulated copper concentrator tailing was built and put into operation. During the experimental period, the first step was that of laboratory experiments or beaker leaches. The results on this small scale were so satisfactory that a small operating plant, capable of handling 5 tons of roasted tailing per day, was installed. Again, the results proved satisfactory and an 80­ton plant was built and operated continuously from August until February, 1913. In this plant, full-sized roasting and leaching units were

Jan 8, 1916

By M. G. Driessen, H. E. Criner

Possible applications of cyclone thickeners for: (1) clarification of the washery water and, (2) recovery of fine coal from the plant bleed. The paper shows: (1) that it is possible to remove all particles including the very finest, from the circulating water, thus obtaining a closed water system and, (2) that reduction of the ash content of the solids of the plant bleed is feasible by means of cyclone thickeners. Performance data for different size cyclones is given in the form of graphs.

Jan 1, 1950

By Frank G. Snyder

The Precambrian of Midcontinent United States includes a metamorphic belt of probable Middle Precambrian age, a belt of Keweenawan volcanics and sediments, and widespread igneous activity that extended from Iowa to Texas. Most of the present structural configuration of the Midcontinent was developed by epeirogenic movements during the Paleozoic. The dominant elements are basins and arches. Three major metallogenic provinces occur in the Midcontinent. They include the Missouri Precambrian iron ores, the Lake Superior copper ores, and the Mississippi Valley lead-zincbarite- fluorite deposits. Several large iron deposits, occurring in rhyolite and andesite host rocks, are known. Both discordant massive bodies and replacement- type bodies occur. The iron deposits are believed to have been formed during the period of igneous activity. They are essentially the same age as the volcanics and older than the granites that intrude the volcanics. The Lake Superior copper ores include two established districts, the Keweenawan district and White Pine, and the copper-nickel deposits in the Duluth gabbro. The lead-zinc-barite-fluorite deposits include four major districts, Southeast Missouri, Upper Mississippi Valley, Tri-State, and Illinois-Kentucky, and at least eight minor districts. Ore may occur in stratiform deposits and in veins. The major districts all contain stratiform deposits, but several have produced appreciable quantities of vein ore. Only vein deposits are known in some of the smaller districts. The major features of all districts can be catalogued in terms of host rocks, structural patterns of districts, types of ore-bearing structures, and mineralogical characteristics. From these features, a Mississippi Valley type ore body, in its type area, can be defined.

Jan 1, 1968

By S. R. B. Cooke, H. S. Choi, I. Iwasaki

In a previous article1 the function of various fatty acids as collectors for iron ores was reported for the two alternate processes; (a) the flotation of iron-oxide minerals, and (b) the flotation of calcium-activated siliceous gangue. The selectivity of separation was shown to be markedly dependent not only on such common parameters as pH and the levels of collector and activator addition, but also on the structure and the degree of unsaturation of the acids used. The iron ores employed consisted primarily of hematite, goethite, and quartz and as the effectiveness of any one acid on the separation depends on the individual response of each constituent mineral toward the given collector, a comprehensive knowledge of the floatability of the individual minerals is desirable for the interpretation of the results obtained. The mechanism by which a collector ion becomes attached to a mineral-solution interface has been a subject of much investigation. From quantitative studies of the properties of the electrical double layer on mercury2 and on several solid surfaces3,4,5,6 , the adsorption of some flotation reagents at the mineral-solution interface is beginning to be understood. For example, it has been demonstrated from streaming potential measurements made on quartz5 and corundum6 that the interfacial electrical condition is strongly dependent on the pH. Thisoccurs presumably through the following electrolytic reaction at the interface, and in the presence of a flotation collector, controls the floatability of the solids. A concurrent investigation of the flotation behavior of goethite and of quartz carried out at the School of Mines and Metallurgy7 has shown a positive correlation with the electrokinetic behavior of these minerals. The purpose of the present investigation was to collect general information on the floatability of hematite, and to investigate the function of various 18-carbon aliphatic acids on the floatability of hematite, goethite, and of activated quartz. Electrophoretic mobility measurements, simplified flotation tests using a modified Hallimond tube, and contact angle and frothability measurements were employed. The results are of direct application in the interpretation of the batch flotation results on natural ores as

Jan 1, 1961

By F. A. Seward

A1though the expanding Eltran1 configuration has been used in induced polarization exploration for several years, there has been little application of this method to straight resistivity problems. A comparison of results of resistivity exploration by this technique versus those obtained from Wenner configuration surveys reveals a number of advantages in interpretative resolution as well as in field operation. The application of electrical resistivity to ground-water exploration is well known.= In the past a major portion of this work has been accomplished by use of one or more variations of a technique employing the Wenner3 electrode configuration. With the introduction of the frequency domain technique of induced polarization measurements, used primarily in the exploration for disseminated sulfide deposits, there arose the need for an electrode configuration by which potentials could be measured externally to the current electrode spread in order to minimize coupling between current sending and potential receiving circuits. It was also deemed desirable that the configuration would provide information laterally along profile as well as with depth. To reach these objectives the expanding dipole-dipole configuration (which probably first was used in the electrical transient method of exploration and from which the name 'Eltran' was derived) has been adapted to induced polarization exploration. The author has successfully applied the same techniques

Jan 1, 1963

By William P. Shinn

Jan 1, 1880

Who's Who in Mineral Engineering - The 1978 Membership Directory of the Society of Mining Engineers of AIME

Jan 7, 1978

Jan 1, 1963

By W. L. Saunders

WHEN work was begun in September, 1910, on the rock excavation for the foundation of the gigantic dam at Valhalla, N. Y., which is to convert Kensico lake into an important storage reservoir of the Catskill Aqueduct system, one of the first steps taken by the contractor, H. S. Kerbaugh, Inc., was the development of a quarry to supply the stone needed in the construction work.The importance of a bountiful supply of suitable rock in an accessible location is apparent when it is considered that nearly a million cubic yards of cyclopean masonry will be contained in the completed structure, not to mention dimension and facing stones, concrete blocks, and mass concrete. The dam structure will be over 1800 ft. long and about 170 ft. above the present river bed. However, for a distance of some 800 ft., it will be carried down to solid ledge rock, which will make the finished structure about 300 ft. in maximum height. It will be about 200 ft. thick at the base and directly beneath the coping it will be 28 ft. thick. This dam will raise the reservoir surface 110 ft. above old Kensico lake. The reservoir capacity will be 29,000,000,000 gal.-equal to New York's total needs for over two months. The contract price for this work is nearly $8,000,000 and is second only in amount to the cost, over $12,600,000, of the Ashokan Reservoir work. Fig. 1 is a view of the dam site.

Jan 2, 1914

By J. B. Clark

In 1933, R. paris1 published a phase diagram for the entire Mg-Ca-Zn system. He reported the existence of a ternary intermetallic phase, Mg5Zn5Ca2, which formed a quasi-binary with the magnesium solid solution. Since then, no extensive work has been reported on the system. Recently however, indications of the existence of a second ternary in-termetallic phase in equilibrium with the magnesium solid solution led to a reinvestigation of the solid phase equilibria involving the magnesium solid solution. The 335°C (635°F) isothermal section was chosen for study. Metallography and powder X-ray diffraction were selected as the best mutually corroborating methods for determining the solid phase constitution. Seventy-six alloys were prepared from singly sublimed (99.95 pct) magnesium, electrolytic (99.95 pct) zinc and USP calcium. The analyses of some of the alloys are shown in Fig. 1. The alloys were melted in a graphite crucible under a chloride flu and chill cast in a split graphite mold. Dif-fusion couples (see Fig. 2) were prepared by casting molten Mg-20 wt pct Zn alloy around a cylinder of Mg-30 wt pct Ca alloy. The alloy samples and the diffusion couples were sealed under argon in Pyrex vials and annealed in a furnace capable of controlling within 1/2°C of 335°C. At the conclusion of the anneal, the alloy samples were quenched in ice water and the diffusion couples were air cooled. Procedures standard for magnesium alloys were used for metallographic examination. Powder X-ray diffraction patterns were taken on a G. E. camera with a 14.32 cm dim using nickel-filtered copper radiation. The redetermined 335°C (635°) section of the Mg-Ca-Zn phase diagram is shown in Fig. 1. TWO ternary intermetallic phases, designated w and

Jan 1, 1962

By K. Leutwyler

The key to realistic casing stress analysis in thermal recovery installations is accurate knowledge of the temperatures involved. Much information leading to prediction of heat losses from tubing string to wellbore has been published. This .same information permits calculation of casing temperature under certain conditions. This paper reviews the basis for most of the published work, the line source solution to the diflusivity equation and examines some of its application criteria in the light of unsteady-state conditions. An alternate finite differences method is presented for correlation, and experimental data pertaining to the heat transfer mechanism in the annulus is reported. In the light of the information presented in the paper, it appears that the assumption of a line source for the tubing-wellbore system is valid even for reasonably short periods of heat flow, .such as "steam soak" operations. The empirically modified equation presented earlier matches computer derived results of the finite differences approach lor periods as short as 50 hours. Previously predicted cas ing temperatures and the associated stress levels are thus verified based on these correlative computations and the reported experimental information. Fall out from the computer output resulting in some studies of the influence of insulating cement properties on casing temperature, and experimentally studied effects of nitrogen placed in the annulus at various pressures., are described. INTRODUCTION Generally speaking, predictions of average casing temperatures have been based on an idealized model involving a centralized tubing string at uniform constant temperature radiating energy towards the casing under steady-state conditions.'. ' Heat is transferred away from the casing to the formation by unsteady-state conduction across thermal barriers consisting of cement and the mud sheath. Heat balances written on the casing permit prediction of instantaneous casing temperatures. During early periods of injection, casing temperature varies appreciably as a function of time; however, for long injection times this variation decays as heat flow from the wellbore to the formation stabilizes, and it becomes virtually negligible as conditions surrounding the wellbore become quasi-steady-state (Fig. 1). Carslaw and Jaeger -escribe a solution to the diffusivity equation for a line source (Fig. 2). A constant supply of heat is introduced into the medium from the line placed into the origin of the x-y coordinate system and parallel to the z-axis. Heat spreads outward in the infinite cylindrical solid and the temperature increase on a line going through point (x, y) parallel to the z-axis at a distance r can be predicted by: The following criterion must be considered: the Carslaw and Jaeger equation is obtained on the basis of a large

Jan 1, 1967