Search Documents

By THOMAS J. CLIFFORD

IN 1926, finer grinding began to be a feature of the milling practice of the Southeast Missouri lead district. Nothing since the adoption of flotation has caused greater changes and greater improvement in results. The trend toward finer grinding, with the consequent discarding of tailing at finer sizes, and consequent lower assays in lead, continued to progress until 1931, when the abnormally low price of lead brought a halt: that is, the better metallurgical results obtained would not offset the increased costs due to higher power and necessary maintenance. Since 1931 a slight tendency toward the discard of coarser tailing has taken place. , In 1926, larger rod mills i.12 ft. 1 in. by 6 ft. 6 in.) than any previously used in the district were installed in cue plant, and a new primary crushing plant, of greater capacity was built. This combination demonstrated immediately the better metallurgical results obtainable by finer grinding and all the mills now running have adopted the practice.

Jan 1, 1934

By S. A. TAYLOR

THERE is probably no other mineral industry of which the public has as much information and misinformation as it has of the coal industry. Unfortunately, however, the general public's knowledge of the coal industry, outside of the particular kind of coal it is accustomed to, by reason of use, is largely made up of information received from newspaper and popular magazine articles, in which the mine workers are depicted as overworked and mistreated men, and the coal operators as "coal barons." Those who have any specific knowledge of exact conditions in the coal industry know how unjust and un- fair such an opinion of the coal industry is, not only to the miner but to the operator as well. Many reporters and writers of magazine articles are misled by statements regarding the condition of the miners that are exaggerated and not founded on facts and, if an investigation of the conditions of the miner's work, his habitation and surroundings were fairly made, it would at least compel more truthful statements by those who write for public reading. That such an investigation would not reveal anything that was wrong, or anything to be censured or cured, no one, I think, would maintain, but I do think that any fair investigation of the facts would show that conditions in and around the newer and later-developed coal mines and communities would compare favorably with those of manufacturing districts, and that where the mines and com- munities are old and not very attractive places to work, or live in, they carry with them other considerations, compensating for these conditions, and cannot be remedied by reason of a lack of sufficient coal to warrant economically any costly changes.

Jan 1, 1926

By Ralph Hultgren, Louis A. Carapella

When F. Heuslerl found in 1898 that certain alloys containing only copper, manganese, and tin were ferromagnetic, the discovery excited a great deal of interest and led to numerous investigations. It was early found that tin could be replaced by aluminum, arsenic, antimony, bismuth, or boron without destroying the ferromagnetic nature of the alloys.2 Copper may also be replaced by silver.% All these alloys have come to be known as "Heusler alloys." The aluminum alloys apparently were the most magnetic and have been most extensively investigated. However, no agreement has yet been reached as to the source of the ferromagnetism arising from these nonferromagnetic elements. Absence of reliable quantitative data makes speculation hazardous. The value of much of the earlier work was vitiated by lack of necessary precautions against contamination, and by lack of close control of heat-treatment. It was only recently established that in aluminum Heusler alloys4 the ferromagnetism arose from a single phase, an ordered body-centered-cubic structure. With modern methods of preparation, heat-treatment, and X-ray examination, it is possible to prepare these alloys without contamination, to heat-treat them intellgently, and to determine what phase or phases are present in the finished sample. In the present investigation, a series of pure alloys in the comparatively neglected copper-manganese-tin system have been prepared, which consist of a single, body-centered-cubic structure (the beta phase) and whose compositions vary within wide limits. The magnetic saturation values of these single-phase alloys have been quantitatively determined, so that considerable data on the effect of composition on the ferromagnetism have been made available. In the course of the investigation some information on the extent of the stability of the beta phase and the nature of phases in adjacent regions of the ternary diagram has been accumulated. Anomalies in earlier data. have been explained, and alloys have been prepared that are much more strongly magnetic than any previous Heusler alloys. Previous Work In the original work of F. Heuslerl and coworkers,2 a maximum magnetic saturation value of I = 107 was found at the composition Cu6Mn3Sn, while a value for CusMnAl of I = 443 was early measured. Ross and Gray5 found a second maximum at the composition Cu2MnSn, which was much more magnetic than Heusler's original alloy. F. Heusler6 hen reinvesti-gated the system, confirmed their results,

Jan 1, 1942

By Louis A. Carapella, Ralph Hultgren

When F. Heuslerl found in 1898 that certain alloys containing only copper, manganese, and tin were ferromagnetic, the discovery excited a great deal of interest and led to numerous investigations. It was early found that tin could be replaced by aluminum, arsenic, antimony, bismuth, or boron without destroying the ferromagnetic nature of the alloys.2 Copper may also be replaced by silver.% All these alloys have come to be known as "Heusler alloys." The aluminum alloys apparently were the most magnetic and have been most extensively investigated. However, no agreement has yet been reached as to the source of the ferromagnetism arising from these nonferromagnetic elements. Absence of reliable quantitative data makes speculation hazardous. The value of much of the earlier work was vitiated by lack of necessary precautions against contamination, and by lack of close control of heat-treatment. It was only recently established that in aluminum Heusler alloys4 the ferromagnetism arose from a single phase, an ordered body-centered-cubic structure. With modern methods of preparation, heat-treatment, and X-ray examination, it is possible to prepare these alloys without contamination, to heat-treat them intellgently, and to determine what phase or phases are present in the finished sample. In the present investigation, a series of pure alloys in the comparatively neglected copper-manganese-tin system have been prepared, which consist of a single, body-centered-cubic structure (the beta phase) and whose compositions vary within wide limits. The magnetic saturation values of these single-phase alloys have been quantitatively determined, so that considerable data on the effect of composition on the ferromagnetism have been made available. In the course of the investigation some information on the extent of the stability of the beta phase and the nature of phases in adjacent regions of the ternary diagram has been accumulated. Anomalies in earlier data. have been explained, and alloys have been prepared that are much more strongly magnetic than any previous Heusler alloys. Previous Work In the original work of F. Heuslerl and coworkers,2 a maximum magnetic saturation value of I = 107 was found at the composition Cu6Mn3Sn, while a value for CusMnAl of I = 443 was early measured. Ross and Gray5 found a second maximum at the composition Cu2MnSn, which was much more magnetic than Heusler's original alloy. F. Heusler6 hen reinvesti-gated the system, confirmed their results,

Jan 1, 1942

NEW MEMBERS The following list comprises the, names of those persons who became members during the period June 10 to July 10, 1914: Members ALDRICH, HAROLD W., Supt. of Leaching Plant, Washoe Red. Wks., Anaconda Copper Co., Anaconda, Mont. AYER, FRANK ASHTON, Mine Foreman.. ..Detroit Copper Co., Morenci, Ariz. BELL, ARTHUR F. L., Chief Engr., Associated Oil Co.., 817 Sharon Bldg., San Francisco, Cal. BERGMAN, JULIUS GUSTAF, Mech. Engr., Chief Draftsman, Arizona Copper Co. Morenci, Ariz. BURT, CURTIS F., Min. Engr., Pittsburg-Dolores Mining Co., Rockland, via Yerington, Nev. CALLAWAY SCOTT DAVID, Chem La Harpe Smelter Co., La Harpe, Kan. CAMPBELL, W. C., Min. Engr 4 Princess St., Roodeport, Transvaal, So. Af. CARROLL, GEORGE A., Genl. Mgr Kildare Min. Co., Manson, B. C., Canada. CARUTHERS, JOHN LYTLE, Min. Engr., Asst. Engr., St. Louis, Rocky Mountain & Pacific Co.. Raton. N. M.

Jan 8, 1914

By Charles Macdonald

Wrought-iron eye-bars for bridges and roofs, designed upon what is known as the pin connection system, have been successfully manufactured in this country for some years. The most approved methods employed have been the hydraulic upsetting process, and by die-forging under a hammer. In upset eyes the fibre of the iron is necessarily much distorted ; and in bars of considerable size, this disturbance seriously impairs the strength of the connection. Mr. Collingwood, in discussing my paper on "Proportions of the Heads of Eye-bars," read before the American Society of Civil Engineers, Jan. 21st, 1874, submitted sketches of certain bars intended for the anchorage of the East River bridge, which had been exposed to the action of sulphuric acid a sufficient length of time to thoroughly cleanse the surfaces, and expose the condition of the fibre. These sketches are here reproduced for the purpose of illustrating the effect of this method of manufacture. In Figs. 1, 2, and 3, it will be observed that the fibres at A, and E, have been folded back upon: themselves and otherwise twisted and disturbed, in a manner not calculated to inspire confidence in the integrity of the connection. To compensate for this defect, a large excess of metal is thrown into the eye; but a method of manufacture which involves such a necessity, even although it be the one giving the best results thus far, all things being considered, is far from being perfect.

Jan 1, 1879

By Colin G. ink

OUTSTANDI'NG in progress among the less familiar 'metals during 1936 is the electrolytic production of 99.9 per cent manganese meta1 readily and many quantity. Strictly speaking, manganese should not' be classed as 'a rare metal, since there is 800 times as much manganese in the earth's crust as there is zinc or lead. But manganese' as a metal is rare, just as titanium metal is rare though titanium is five times as abundant in the earth's crust as manganese.

Jan 1, 1937

By A. C. Losekamp, R. M. Fincel, J. B. Conway

TANTALUM like several other metals exhibits a great affinity for or reactivity with certain gases. Tested in atmospheres which are not completely pure this metal becomes contaminated by certain impurities (notably nitrogen, oxygen, and hydrogen) with a resultant change in various properties. Well-known are the drastic changes in hardness, ductility, and electrical resistivity. Also previously recorded are the distortions of the lattice1,2 accompanying the increased content of oxygen and nitrogen in tantalum. This pronounced affinity for certain gases along with the significant property variations thereby produced makes it necessary to observe additional experimental precautions in making various property determinations with tantalum. Some recent measurements of the linear thermal-expansion characteristics of tantalum have made this point quite emphatically. Failure to observe the greatest precautions in reducing the contaminating influence has led to some extremely distorted results. Not only does such operation lead to different heating and cooling curves during the thermal-expansion measurements, but upon cooling to room temperature the sample is found to have suffered a permanent (actually semipermanent since the specimen can be returned to its original length by a 3-hr degassing treatment in vacuum at 2300°C) elongation. In addition, subsequent heatings will not follow the initial heating curve unless the expansion measurements are based on the actual specimen length at the beginning of the heating cycle. These thermal-expansion measurements were made by positioning the specimen horizontally at the longitudinal midpoint of a 20-in.-long, 4-in.-diam resistively heated tungsten tube furnace. The specimens were in the form of 20-mil sheet formed into a sharp U-shape about 0.3 in. in width and 0.3 in. in depth. Fiducial marks in the form of 0.010-in. holes drilled at either end of the 2.5-in.-long sheet specimens were viewed by a paired filar micrometer telescope system mounted on an Invar bar on the top of the furnace. Tests were made in helium with temperatures measured by a Pt/Pt-lORh thermocouple to 1000°C; above 1000°C temperature was measured by means of an optical pyrometer sighted into a black-body hole drilled into the specimen-holding fixture in the vicinity of the specimen. Previous tests with black-body holes drilled in a 0.25-in.-diam rod specimen had confirmed the temperature uniformity between specimens and specimen-holding fixture in this furnace. A typical thermal-expansion curve for arc-cast tantalum in helium is shown in Fig. 1 for the case where no attempt is made to remove all the impurities from the cover-gas atmosphere. The initial heating curve appears smooth and has a shape characteristic of all metals. However, it is known that the sample begins absorbing impurities at temperatures above 1000°C which are sufficient to distort the lattice and lead to specimen lengths which are somewhat larger than would be obtained in the absence of contamination. During the cooling cycle the expansion curve is seen to be significantly different from the heating curve. This is due to the impurity content causing a semipermanent (i.e., permanent until the impurities are removed by vacuum degassing) deformation which will not allow the speci-

Jan 1, 1965

For handling rough rock, the shovel-train system is unexcelled. The ideal application is a physically large, but not excessively deep, open-pit mine from which the coarsely blasted ore and waste must be transported distances in excess of three miles. If, in addition, a high production rate is to be maintained, railroad haulage will probably afford a lower cost per ton transportation than will any other haulage method. Relatively gentle grades must be employed- usually 3% for uphill hauls and 4% for downhill hauls. The greater the differences in elevation the greater are the railroad track grade space requirements. By way of illustration, a 3% ramp out of a pit only 300 ft deep must be almost two miles long. Mainline track locations should be selected carefully so that the frequency of movements during the life of the mining operation is minimized. This applies both to ore and to waste haulageways. Such moves are not only expensive but difficult to execute without adversely affecting production rates. The large mine affords greater opportunities for judicious location of semi-permanent trackage.

Jan 10, 1967

By J.B. Pullen

The United Verde mine is in the north central part of Arizona, on the northeasterly slope of the Black Hills, near the town of Jerome. Ore was first discovered in the district about 1875, and the first mining claims were located by M. A. Ruff-ner and associates in 1877. In 1888 the late Scnator William A. Clark secured control of the property and under his ownership it developed into one of the country's most important copper producers. The property was sold to the Phelps Dodge Corporation in 1935, and since then has been under this Corporation's management. Except for shutdowns caused by general world-market conditions, production has been continuous from 1890 to date. Geology The mineralized zone ranges in area from approximately 12 acres to less than 5 acres. All mineralization occurs in the pre--Cam-brian intrusives. The first intrusion, according to geologic records, was the quartz porphyry, which later was intruded by augite diorite. Following the diorite intrusion through a series of intrusions of lesser magnitude, a pipelike mass of massive sulphide, quartz and rock was formed. The diorite forms the hanging wall of this mass, and the porphyry the footwall. Between the footwall and the sulphide a band of chlorite schist was formed, probably owing to metamorphic conditions. Commercial ore occurs along the contact of the schist and sulphide extending into the sulphide, sometimes entirely through the schist, and fingering out into the porphyry. The ore deposit was formed by replacement similar to deposits formed in limestone areas. Faulting and deformation occurred in pre-Cambrian times and again in the Tertiary period, removing approximately 2000 ft. from the top of the main United Verde ore body, forming the United Verde Extension ore body, the only other major ore body in the district. Major development work has shown that the sulphide mass extends to the 3300-it. level, and diamond drilling below this level has indicated that the mass might extend below the 3700-ft. level, but in a diminished quantity. While many copper minerals exist in the mine, the chief commercial mineral is chalcopyrite. Aplan and vertical section of the mineralized zone showing the principal geological eatures is shown in Figs. I and 2. General Description and Physical Condition or Mine After over 50 years of active production, ore still exists on almost every level of the mine. This condition is due to many causes —-mine fires, which broke out as early as 1894, caused the abandonment of certain areas; subsidence and ground movements retarded the cleaning up of others. Furthermore, in the early days there was such an abundance of ore that when mining became dificult it was a simple matter to replace the production by going to a deeper level. Several attempts were made to recover the ore in the fire zone, both by glory-holing

Jan 1, 1943

By J. B. Pullen

The United Verde mine is in the north central part of Arizona, on the northeasterly slope of the Black Hills, near the town of Jerome. Ore was first discovered in the district about 1875, and the first mining claims were located by M. A. Ruff-ner and associates in 1877. In 1888 the late Scnator William A. Clark secured control of the property and under his ownership it developed into one of the country's most important copper producers. The property was sold to the Phelps Dodge Corporation in 1935, and since then has been under this Corporation's management. Except for shutdowns caused by general world-market conditions, production has been continuous from 1890 to date. Geology The mineralized zone ranges in area from approximately 12 acres to less than 5 acres. All mineralization occurs in the pre--Cam-brian intrusives. The first intrusion, according to geologic records, was the quartz porphyry, which later was intruded by augite diorite. Following the diorite intrusion through a series of intrusions of lesser magnitude, a pipelike mass of massive sulphide, quartz and rock was formed. The diorite forms the hanging wall of this mass, and the porphyry the footwall. Between the footwall and the sulphide a band of chlorite schist was formed, probably owing to metamorphic conditions. Commercial ore occurs along the contact of the schist and sulphide extending into the sulphide, sometimes entirely through the schist, and fingering out into the porphyry. The ore deposit was formed by replacement similar to deposits formed in limestone areas. Faulting and deformation occurred in pre-Cambrian times and again in the Tertiary period, removing approximately 2000 ft. from the top of the main United Verde ore body, forming the United Verde Extension ore body, the only other major ore body in the district. Major development work has shown that the sulphide mass extends to the 3300-it. level, and diamond drilling below this level has indicated that the mass might extend below the 3700-ft. level, but in a diminished quantity. While many copper minerals exist in the mine, the chief commercial mineral is chalcopyrite. Aplan and vertical section of the mineralized zone showing the principal geological eatures is shown in Figs. I and 2. General Description and Physical Condition or Mine After over 50 years of active production, ore still exists on almost every level of the mine. This condition is due to many causes —-mine fires, which broke out as early as 1894, caused the abandonment of certain areas; subsidence and ground movements retarded the cleaning up of others. Furthermore, in the early days there was such an abundance of ore that when mining became dificult it was a simple matter to replace the production by going to a deeper level. Several attempts were made to recover the ore in the fire zone, both by glory-holing

Jan 1, 1943

By H. R. Tunnell

Every one connected with a mine knows that it is hard to keep down the costs of moving ore from the place where it is broken to the shaft or portal. Considered broadly, the subject of handling would cover all work done in a mine, but here it has been limited to handling ore in stopes and drifts, through chutes, and on levels. Good ventilation and a strict enforcement of rules for the prevention of dust safeguard the health of the men and lower transportation costs. Handling ORe in Stopes and Drifts The object of all stoping is to mine ore of good grade at low cost. In Butte, most of the ore is mined, from veins dipping from 60° to the horizontal to those which are vertical, by means of square-set, rill, timbered-rill, and back-filling stopes. When blasted, a part of the rock is carried by gravity to the grizzlies over the chutes, the rest is shoveled. Rock, when broken in a stope, may be deflected by inclined floors or slides toward the top of a chute leading to the level below. Ore broken clean enough to ship should be carried, by the force of its fall, into a chute or.as nearly into that chute as the safety of the stope and the men permits. Ore that requires sorting, about 80 per cent. of all ore mined, is caught on a grizzly and the waste picked out. Waste rock broken in a stope is used to fill that stope and should be blasted into the gob with as little handling as possible. About two-thirds of all the ore mined in Butte comes from square-set stopes; this method was used in nearly all cases until 1912, when the rill method of stoping was introduced in the Tramway mine, of the Anaconda Copper Mining Co. The shoveling and timbering costs in square-set stopes are high when compared with the costs in the rill stopes. All the ore cannot be carried to the chute, in falling from place, unless the chutes are very close together or the distance from the back of the stope to the top of the chute is sufficient to slide all the ore broken. The number of chutes is limited by the tendency of the ground to cave; if carried too close together the stope is weakened. Small stopes, or blocks,

Jan 1, 1923

By H. R. Tunnell

Every one connected with a mine knows that it is hard to keep down the costs of moving ore from the place where it is broken to the shaft or portal. Considered broadly, the subject of handling would cover all work done in a mine, but here it has been limited to handling ore in stopes and drifts, through chutes, and on levels. Good ventilation and a strict enforcement of rules for the prevention of dust safeguard the health of the men and lower transportation costs. Handling ORe in Stopes and Drifts The object of all stoping is to mine ore of good grade at low cost. In Butte, most of the ore is mined, from veins dipping from 60° to the horizontal to those which are vertical, by means of square-set, rill, timbered-rill, and back-filling stopes. When blasted, a part of the rock is carried by gravity to the grizzlies over the chutes, the rest is shoveled. Rock, when broken in a stope, may be deflected by inclined floors or slides toward the top of a chute leading to the level below. Ore broken clean enough to ship should be carried, by the force of its fall, into a chute or.as nearly into that chute as the safety of the stope and the men permits. Ore that requires sorting, about 80 per cent. of all ore mined, is caught on a grizzly and the waste picked out. Waste rock broken in a stope is used to fill that stope and should be blasted into the gob with as little handling as possible. About two-thirds of all the ore mined in Butte comes from square-set stopes; this method was used in nearly all cases until 1912, when the rill method of stoping was introduced in the Tramway mine, of the Anaconda Copper Mining Co. The shoveling and timbering costs in square-set stopes are high when compared with the costs in the rill stopes. All the ore cannot be carried to the chute, in falling from place, unless the chutes are very close together or the distance from the back of the stope to the top of the chute is sufficient to slide all the ore broken. The number of chutes is limited by the tendency of the ground to cave; if carried too close together the stope is weakened. Small stopes, or blocks,

Jan 1, 1923

By H.A. Schwartz

From time to time, one of the authors has had occasion to investigate the graphitizing reaction and has published the results mainly as discussion' of the work of other investigators. In view, therefore, of the diversity of both observations and interpretation, it seemed well to attempt, a revision of the entire subject in the Research Laboratory of the National Malleable Castings Co. The work consisted of a careful study of a single, impure, iron-carbon alloy. The material, which may be considered typical low-carbon white cast iron of the malleable industry, was an air-furnace iron of the following composit,ion: carbon 2.30 per cent., silicon 1.20 per cent., manganese 0.29 per cent., phosphorus 0.156 per cent., sulfur 0.048 per cent. The freezing range extended from 1213' to 1132' C., the latter figure agreeing with Gontermann's data.2 We have attempted to define the equilibrium diagram of this alloy, in the stable condition as related to the mctastable diagr,aui,- from a temperature somewhat below the euteetic freezing point to a temperature l>clow Arl and for a graphitic-carbon content from practically notliing to the original total rarbon of the specimen (see Fig. 6). More csp~c~ially we desired to locate the line in the stable diagra~n corrcspo~idi~lg to thc Ac, line of the metastable syst,ern, which is designated by analogy, thc At, line (t, from tcrnpcr carbon); also to dctermirle the locat'ion of A tm witah respect, to Acm t,o~vard their lowcr extremities at Arl in ordei to determine whether or not graphitization is completed by th~ separation of an iron-carbon entectoid analogous to pearlite in the iron-cementite system. This would involvc furthcr a colnparison of thc locations of Ihc stablc and met.astable 41 points. As the carbon concelltrations of thc solid solutions of the two syste~~ls are probably not, identical, an explanation of t>lieir differences and of thc,

Jan 1, 1923

By H. A. Schwartz

From time to time, one of the authors has had occasion to investigate the graphitizing reaction and has published the results mainly as discussion' of the work of other investigators. In view, therefore, of the diversity of both observations and interpretation, it seemed well to attempt, a revision of the entire subject in the Research Laboratory of the National Malleable Castings Co. The work consisted of a careful study of a single, impure, iron-carbon alloy. The material, which may be considered typical low-carbon white cast iron of the malleable industry, was an air-furnace iron of the following composit,ion: carbon 2.30 per cent., silicon 1.20 per cent., manganese 0.29 per cent., phosphorus 0.156 per cent., sulfur 0.048 per cent. The freezing range extended from 1213' to 1132' C., the latter figure agreeing with Gontermann's data.2 We have attempted to define the equilibrium diagram of this alloy, in the stable condition as related to the mctastable diagr,aui,- from a temperature somewhat below the euteetic freezing point to a temperature l>clow Arl and for a graphitic-carbon content from practically notliing to the original total rarbon of the specimen (see Fig. 6). More csp~c~ially we desired to locate the line in the stable diagra~n corrcspo~idi~lg to thc Ac, line of the metastable syst,ern, which is designated by analogy, thc At, line (t, from tcrnpcr carbon); also to dctermirle the locat'ion of A tm witah respect, to Acm t,o~vard their lowcr extremities at Arl in ordei to determine whether or not graphitization is completed by th~ separation of an iron-carbon entectoid analogous to pearlite in the iron-cementite system. This would involvc furthcr a colnparison of thc locations of Ihc stablc and met.astable 41 points. As the carbon concelltrations of thc solid solutions of the two syste~~ls are probably not, identical, an explanation of t>lieir differences and of thc,

Jan 1, 1923

By A. N. Holden, J. H. Hollomon

Inhomogeneous yielding during the early stages of plastic flow has been observed in many metals and has long been a subject of controversy. Low carbon steel, when strained at room temperature, exhibits a distinct yield point at which the metal ceases to behave elastically and begins to flow plastically without further increase in stress,† often with an actual decrease in stress from that existing at the yield point. One manifestation of this behavior is the familiar Lüders lines. The extent of the yield point elongation (the plastic strain which results without raising the stress above that at the initial yield point) may be several percent. Several explanations of this type of yielding in steels have appeared in the literature:1-3}; 1. The segregation of carbides or other constituents at the grain boundaries of ferrite forms cell-like blocks which break down at a higher stress than that at which the ferrite alone will flow. 2. The precipitation of various constituents within the ferrite itself in some way blocks initial flow until a higher stress is reached, after which a great deal of flow occurs without further increase in stress. 3. The restraining influence of neighboring, less favorably oriented grains in a polycrystal results in a storing up of energy, which on yielding is sufficient to cause the continued propagation of slip bands on the multiplicity of slip systems available in adjacent iron crystals without increase in stress. 4. Local segregation of carbon atoms increases the stress required for the initial propagation of dislocations. The stress required for further deformation is lower.3 Such an explanation would require the presence of upper and lower yield points in single crystals. Low and Gensamer2 have shown that heterogeneous yielding can be eliminated by removal of carbon and nitrogen from polycrystalline steels by wet-hydrogen treatment. They also demonstrated that the re-introduction of minute amounts of carbon or nitrogen caused a return of the yield point. Observations of the initial flow of single crystals containing small amounts of carbon and nitrogen- should provide a clue to the explanation of inhomogeneous yielding. Previous tests of iron crystals4-6 can not be considered conclusive because it is uncertain whether the carbon and nitrogen were satisfactorily removed by the decarburization technique employed. The purpose of the experiments described herein was to determine whether single iron crystals containing either carbon or nitrogen would exhibit in-homogeneous yielding. Experimental Procedures THE PREPARATION OF SINGLE CRYSTALS All crvstals were formed in the following way. Aluminum killed sheet material 80 mils thick was machined into specimens of the outer contour shown in Fig 1. These mildly tapered specimens were decarburized at 730°C for 16 hr in hydrogen that had been bubbled rapidly through water maintained at 70°. The resultant grain size after decarburizing was approximately ASTM 5. Several stress-strain curves were made of the decarburized niate-

Jan 1, 1950

By I. R. Kramer

A delay time for yielding in cold-worked face-centered-cubic metals was found. Slip on (123) planes was observed. Glide on these planes occurred during the delay-time period before slip starts on the (111) planes. AN important approach to the study of the anchoring and blocking of dislocations is available through the delayed-yield phenomenon which has been observed in body-centered and hexagonal close-packed metal by several investigators. Clark and his associate1-5 showed that a delay time for yielding is present in mild steels and fine-grain molybdenum. Type 302 stainless, SAE 4130 normalized, SAE 4130 quenched and tempered, and 24s-T aluminum aid not have a delay time. Kramer and Maddin6 studied the delay-yield effect. in metal single crystals. While they found a delay time in body-centered-cubic metals none could be found in the face-centered-cubic metals. Later7 a delay time was found in hexagonal close-packed metals. cottrell8 has proposed an explanation for the difference in the yield phenomena of b.c.c. and f.c.c. metals based upon the anchoring of edge dislocations by the proper types of impurity atoms (C and N). In the body-centered-cubic lattice the interstitial atoms are near a cube edge and can interact with an edge dislocation, while in a face-centered-cubic lattice the distortion around an interstitial atom is of spherical symmetry and cannot anchor a screw dislocation which has practically no hydrostatic component. Cottrell's theory seems to account rather well for the behavior of body-centered-cubic . metals. EXPERIMENTAL PROCEDURE The apparatus used in these experiments is essentially of the same design as described previously.' Single crystals 1 in. long and having a diameter of % in. were placed in a pendulum which consisted of a bar 8 ft long designed with a crystal holder to accommodate the specimen at low temperatures. This portion of the apparatus was supported on fine molybdenum wires. A bar of the same diameter and length comprised the other portion of the apparatus. This bar was supported on a set of roller bearings arranged around the periphery of the bar to allow accurate alignment. This bar was propelled by means of a spring-loaded gun and allowed to strike the lead bar in front of the single-crystal specimen. SR-4 type A-8 resistance strain gages were cemented to the specimen and the strain measurements were obtained by amplifying the strain-gage output by means of a high-gain preamplifier. A tektronix 545 oscilloscope was used together with a polaroid camera to record the strain and time sweep. An Ellis Associate Bridge was used to calibrate the strain gages and calibration readings were obtained before each test. The sweep of the time signal was initiated by means of a miniature thyraton which was fired when the two bars came into contact. The single-crystal specimens were cut from single-crystal bars about 12 in. long, grown by a modified Bridgman technique. The aluminum crystals were made with material of 99.99 pct purity while the purity of the copper was 99.999 pct. A cut-off wheel was used to prepare the specimens which were then machined to the desired length. The two opposite faces of the specimen were parallel to each other and perpendicular to the axis of the specimen. The specimens were compressed 1 pct. No machining followed thereafter. In some cases prestraining was carried out in liquid nitrogen by impacting the specimens directly in the apparatus so that subsequent observations could be made without allowing the specimen to warm up to room temperature. The single crystals were compressed 1 pct at room temperature in a hand press without much control of the rate of deformation. In some cases specimens were recompressed to obtain the desired length change. As far as could be determined in these experiments this factor did not seem to influence the results. The SR-4 strain gages were glued with a cellulose type cement onto the specimen surface and baked at 45°C for 12 hr. As a check on the baking treatment gages were allowed to dry at room temperature. All delay time tests in this paper were conducted in a liquid nitrogen bath at -195°C. A schematic delay time oscilloscope trace is shown in Fig. 1. At point B the elastic stress wave caused by the impact reaches the strain gage on the specimen. The portion BC is the elastic strain. In this investigation the strain at point C was used to calculate the critical resolved shear stress by multiplying by the proper modulus depending upon the orientation of the single-crystal specimen. The time between C and D is the delay time portion of the curve. This portion of the curve is fairly flat but does have a definite microstrain associated with it. After the point D is reached the specimen deforms rapidly and the strain reaches a maximum at E. Following this, depending upon the length of the bar behind the specimen, the strain remains constant for a period and then decreases when the reflected elastic wave returns from the end of the pendulum bar. A permanent plastic strain is recorded on the oscilloscope trace and also measured by a strain-measuring bridge. The strain, E p,

Jan 1, 1960

By Y. A. Chang

Heat content values of tantalum monocarbide and tungsten monocarbide have been determined from 325" to 985°K by means of a drop-type diphenyl ether calorinzeter. Based on the values obtained in the present study and those available in the literature, best values lected and computed from 298. 15°K to temperatures close to their respectiue melting points. At temperatures higher than 1700°Kfor TaC and 27000 K for WC, values of Cp and related thermodynamic quantities were extrapolated based on the two Debye parameters: one corresponds to the metal sublattice and the other to the carbon sublattice. The contrzbutzon In the total specific heat due to lattice dilation was evaluated using the Nernst-Lindemann relalionship. The calculated values of Cp were in good agreement with the In view of their refractoriness, tantalum monocar-bide (TaC) and tungsten monocarbide (WC) are of con- experimentally determined ualues. Furthermore, the calculated values of the absolute entropies at 298.15"K were 5.03 and 4.15 in comparison to the experimental values of 5.05 and 4.15, all expressed in the unit of cal per degg-atom. Using the same Debye parameters, values of the linear coefficients of ther mal expansion for TaC and WC were calculated from absolute zero to their respective melting points using the Grüneisen equation. The calculated values are in excellent agreement with the experimental values available in the literature. Finally, the values of the bulk modulus of TaC from room tenzperature to temperature near its melting Point were also calculated using the equation recently derived by Anderson. No cot~ipari-son between the calculated and experimental values can be made due to lack of experimental data. siderable practical interest. In order to completely define these materials, it is necessary to know their thermal properties as a function of temperature. Tantalum rnonocarbide having a NaCl structure (B-1 type) melts congruently at 4250PK,1 while tungsten monoearbide with a simple hexagonal structure (Bh type) melts per itectically at 3049°K into melt and graphite.2 In the present study, the heat content values (from which

Jan 1, 1968

By Franklin H. Wilson

COPPER base alloys containing various amounts of aluminum and silicon are of considerable commercial interest. In particular the alloy containing 7 pct aluminum and 2 pct silicon shows an attractive combination of high strength with excellent machinability. Since there is no evidence in the literature that this ternary system has been studied since the recognition by Smith1 and Anderson2 in 1939 of the kappa phase of the binary copper-silicon system, the determination of the equilibrium phase relationships in the copper corner of the ternary diagram has been undertaken to provide a fundamental basis for understanding the behavior of these alloys. Phase boundaries have been determined by the micrographic examination of quenched samples while points on the liquidus surface have been obtained by thermal analysis. The results, of sufficient precision to serve their major purpose of providing a guide for the control of the manufacture of alloys in the region covered, are presented in a series of both isothermal and vertical sections of the diagram. ALLOYS STUDIED For a rough survey of the copper corner of this ternary system the compositions listed in Table I (Series A) were employed. The results of examinations of these alloys indicated that the compositions listed in Table 2 (Series B) would further clarify regions of greater complexity. All alloys were prepared as 1200 g heats, the copper being melted under charcoal, and then first silicon and then aluminum were added. An [ ] excess of 0.05 pct silicon was allowed to cover deoxidation losses. Two small bars 5/8 by 1 ¼ by 1 ¼ in. were cast using Durville type casting equipment. Analyses were made on all alloys using material which was hot-rolled at 800 or 850°C and annealed 17 hr at 650°C. All analyses were found to be within 0.05 pct of the nominal composition. Since the precision of analysis is not much better than this, the points of both isothermal sections and vertical sections at fixed aluminum and silicon contents have been plotted at the compositions indicated by the nominal composition.

Jan 1, 1948

By Eugene F. Poncelet

Glass squares compressed on edge by steel jaws in poor contact with them developed jagged "partial-contact" cracks caused by the formation of local tensile stresses. Compressed by steel jaws in perfect contact, they developed smooth "release cracks" during release of the pressure, caused by the formation of local tensile stresses during the release of the pressure. All these cracks were parallel to the pressure. A Microflash photograph of a disintegrating specimen under sufficient pressure reveals a network of fractures roughly normal to each other, also "release cracks" and a disintegration cloud. The Griffith theory is amended to account for the formation of a first crack. A new theory, based on the theory of thermal agitation and wave propagation, is proposed to account for the progress, velocity and forking of cracks. The network of fractures is shown to have been caused by reflection at a free boundary of pressure pulses emanating from a first crack. Postulating equal distribution of energy in the pulses emitted on either side by a crack in particles, the smaller fragments are shown to continue fracturing preferentially while some of the coarser fragments remain as residual pieces. As comminution of the smaller fragments proceeds, the solid is reduced to a collection of residual particles of smaller and smaller sizes, accounting for the disintegration cloud. Experimental Procedure Apparatus A crushing device was built, consisting of a steel frame and two polished, hardened steel jaws to crush plate-glass samples. This device was placed between the plates of a hydraulic press (Fig. I). For centering the pressure, the upper jaw was guided vertically and provided with a rounded top. Later it was replaced by a steel jaw ground out of a 2½-in. steel ball, the lower surface being ground to an optical flat (Fig. 2). Four rollers were used to eliminate side thrust. Screws and centering blocks served to center the specimen in the crushing device. Hard steel shims placed under the shoulder of the upper jaw limited the "follow through'' of the jaw after failure of the specimen. Stress distribution was first examined with a polariscope mounted on an optical bench, using monochromatic light. It was found convenient to mount polaroid, quarter wave and monochromatic plates directly on the device itself. A Microflash unit* was used as light source for the photographs. A gold-paint pattern was fused on the plate-glass specimens and connected into the spark-

Jan 1, 1947