Search Documents

By John T. Norton

N order to attempt to arrive at a better under-Jl standing of the whole basic problem of sintering, these remarks will serve as an introduction for discussion that is included and will, perhaps, help to isolate specific questions which need to be answered or to suggest some definite avenues of investigation which should be followed. To bring some sort of logical order into the presentation, I will consider the various types of interaction between the metal to be sintered and the atmosphere which surrounds it, depending upon whether the phenomena are essentially chemical or physical in nature. For example, when the only necessary criterion for the satisfactory sintering of a certain powder is the removal of an oxide skin, then the problem of choosing a suitable atmosphere is primarily chemical; however, if a special surface condition as a consequence of the oxide skin removal is necessary for particularly effective sintering, then the problem becomes a physical one. Of course, the two aspects overlap considerably, but it may be possible to make a distinction in principle if not in practice. The chemical characteristics of the phenomena will be emphasized, since these are the better known. Metal-gas reactions involved in sintering are controlled primarily by the thermodynamics of the processes involved. In which direction will a reaction go and how far before it stops? The answer is to be found in the magnitude of the free energy change associated with the reaction. If a constituent is to be removed from the specimen as completely as possible or if a constituent is to be formed in the specimen as completely as possible, then one chooses conditions which are far from equilibrium so that the reaction is driven toward completion. On the other hand, if the composition is to be maintained at a desired value, then conditions are adjusted as closely as possible to the equilibrium point. This aspect of the problem is susceptible to quite precise analysis, provided, of course, that the significant reactions can be recognized and the required thermodynamic data are available. Conversely, if one asks how fast the reaction goes or how far it proceeds in a given time, the answer is frequently much more difficult to answer in quantitative terms. Yet the rate-con trolling factors of the reactions may be of primary importance in the success of a particular operation, especially where competing processes are at work. Both equilibrium and rate factors must be understood if a clear picture is to be obtained. For instance, in a process for carburizing titanium dioxide, is the difficulty of obtaining a stoichiometric Tic due to a true limitation of the equilibrium or simply to a very slow rate of reaction? An example of this appears in the work of Kalish and Mazza.' They showed that the oxygen content of sintered iron compacts was lower when sintered in pure hydrogen than in the case where the hydrogen was diluted with either argon or nitrogen. The equilibrium oxygen content of the iron would be the same in the two cases, since it is determined by the ratio of the partial pressures of water vapor and hydrogen and this pressure ratio is unchanged by dilution. The rate of oxygen removal, however, under the conditions of a constantly replaced furnace atmosphere, depends upon diffusion and thus upon the concentration of hydrogen in the furnace atmosphere. Possibly the clearest way to illustrate the interplay of these two factors is to consider in more detail some of the typical metal-gas reactions. Adsorbed Gases It is common experience that fine metal powders with their very large surface areas often contain large quantities of gas. This gas, which results from exposure to air or perhaps from some step in the

Jan 1, 1957

By John Wulff, Robert Kamm, M. A. Steinberg

IN a previous paper1 from this laboratory, the development of a lead grid method for exploring the distribution of strain and density within metal powder compacts was described, In that work thin lead foil with rectangular holes cut at regular intervals was inserted with the powder fill, the arrangement pressed and then radiographed to permit measurement of the deformation of the lead grid. Densities at each grid element obtained in this manner were plotted as a function of the die dimensions. From such plots it was, found that the densest part of a compact pressed from one side (the top) is at the top outer region and the least dense at the bottom outer region -of the specimen. The axial density maximum occurs more often nearer the bottom than at the top. As a result of such exploratory measurements, it appeared reasonable to conclude that variations in density could be attributed in the main to die wall friction. Thus compacts of large diameter appeared relatively uniform in density except where the die fill had been uneven. Finally it was found that lubrication of the finely finished die cavity contributed more to magnitude and uniformity of density within the compact than interparticle lubrication. Since publication of the above results, it was found that circular-hole grids could be more accurately made and, when deformed within the powder, more readily measured and analyzed. Much of the former work was repeated and new results which include the effect of lubrication, compact height, pressure, speed of pressing and vacuum pressing are reported in the present paper. CIRCULAR-HOLE GRIDS AND ANALYSES OF RADIOGRAPHS Commercial lead sheet 0.008 in. in thickness was used in all the work reported. The 0.0938-in. diam holes were punched in the sheet on 1/8-in, centers to an accuracy of 0.001 in. The finished grid used contained eight or more holes in a row and from I to 24 rows. The lead sheet was clamped between two pairs of brass strips bolted to a small milling machine table which was itself bolted to a bench in correct position near a vise which held the punch. Travel of the lead grid in two dimensions was controlled by two steel lead screws calibrated in 0.001-in. divisions. A stripper plate was used on the punch to avoid distortion of the lead foil. A high carbon-high chromium (chrocar) one-piece steel die was used throughout the work. The die cavity was 1,125 in. in diam and the clearance between plungers and die wall was 0.001 in, The die was also used for pressing from both ends with two long plungers. Finally, lapping of die and plungers gave a surface whose rms value on an Abbot profilometer was 5 micro-in. The die walls and plungers were, except where otherwise noted, lubricated with a stearic acid suspension in benzene. This was put on in multiple layers and allowed to dry before filling the die.

Jan 1, 1948

By M. A. Steinberg, J. Wulff, R. Kamm

In a previous paper1 from this laboratory, the development of a lead grid method for exploring the distribution of strain and density within metal powder compacts was described. In that work thin lead foil with rectangular holes cut at regular intervals was inserted with the powder fill, the arrangement pressed and then radiographed to permit measurement of the deformation of the lead grid. Densities at each grid element obtained in this manner were plotted as a function of the die dimensions. From such plots it was found that the densest part of a compact pressed from one side (the top) is at the top outer region and the least dense at the bottom outer region of the specimen. The axial density maximum occurs more often nearer the bottom than at the top. As a result of such exploratory measurements, it appeared reasonable to conclude that variations in density could be attributed in the main to die wall friction. Thus compacts of large diameter appeared relatively uniform in density except where the die fill had been uneven. Finally it was found that lubrication of the finely finished die cavity contributed more to magnitude and uniformity of density within the compact than interparticle lubrication. Since publication of the above results, it was found that circular-hole grids could be more accurately made and, when deformed within the powder, more readily measured and analyzed. Much of the former work was repeated and new results which include the effect of lubrication, compact height, pressure, speed of pressing and vacuum pressing are reported in the present paper. Circular-hole Grids and Analyses OF Radiographs Commercial lead sheet 0.008 in. in thickness was used in all the work reported. The 0.0938-in. diam holes were punched in the sheet on 1/8-in. centers to an accuracy of 0.001 in. The finished grid used contained eight or more holes in a row and from I to 24 rows. The lead sheet was clamped between two pairs of brass strips bolted to a small milling machine table which was itself bolted to a bench in correct position near a vise which held the punch. Travel of the lead grid in two dimensions was controlled by two steel lead screws calibrated in 0.001-in. divisions. A stripper plate was used on the punch to avoid distortion of the lead foil. A high carbon-high chromium (chrocar) one-piece steel die was used throughout the work. The die cavity was 1.125 in. in diam and the clearance between plungers and die wall was 0.001 in. The die was also used for pressing from both ends with two long plungers. Finally, lapping of die and plungers gave a surface whose rms value On an Abbot profilometer was 5 micro-in. The die walls and plungers were, except where otherwise noted, lubricated with a stearic acid suspension in benzene. This was put on in multiple layers and allowed to dry before filling the die.

Jan 1, 1949

By G. Donald Emigh

WESTERN phosphate resources which lie in Ida- ho, Montana, Utah, and Wyoming, have seen great expansion of activity in recent years. Growth has been two-pronged: expansion in fertilizer use, and since 1949, into the elemental phosphorous industry. Elemental phosphorous, produced in the electric furnace, goes largely into chemical making. Phosphate ore was first recognized in the West about 1889. Production started in 1906, and for many years consisted of underground operations by small companies operating sporadically. In 1920 Anaconda Copper Mining Co. opened the underground Conda mine near Soda Springs in southeastern Idaho, and has maintained and increased its operations since then. About 1930 Montana Phosphate Products Co. began underground mining in Montana and has remained a steady producer. In 1945 San Francisco Chemical Co., one of the oldest companies in the western field, initiated strip mining at the Waterloo mine near Montpelier, Idaho, and later at Leefe mine near Sage Junction, Wyo. In1946 J. R. Simplot Co. began open pit mining at Gay mine near Fort Hall, Idaho. In 1950 Victor Chemical Works began underground development work in the area of Maiden Rock, south of Butte, Mont.: and has since mined there. Monsanto Chemical Co. began open pit mining near Soda Springs, Idaho, in 1951.

Jan 11, 1954

By H. O. Hofman

At the Lake Superior meeting, September, 1904, Messrs. A. Gibb and R. C. Philp presented a paper entitled " The Constitution of Mattes Produced in Copper-Smelting,"' in which they concluded that ferrous and cuprous sulphides formed the chemical compound, 5 Cu2S, FeS. They arrived at this inference from the observed fact that a matte containing Cu,S, 90.4, and FcS, 9.6 per cent. (or, in round figures, Cu2S, 90, and FeS, 10 per cent.), did not contain any metallic copper, while one with more than 10 per cent. of FeS readily dissolved copper, and with less than this amount retained copper in mechanical suspension. Although they determined the melting-points of five mattes containing from 32.6 to 80.1 per cent. of copper, they did not draw a freezing-point curve, as the necessary apparatus was not available. A microscopical examination of 11 polished samples gave them a grayish-black field of very uniform appearance, except that five of the specimens showed the presence of metallic copper. The object of the present investigation was to supplement the above paper by drawing the freezing-point curve of the ferrous sulphide-cuprous sulphide series, and to see how the constitution could be further revealed by microscopical work. The results obtained lead to conclusions very different from those of Gibb and Philp. While their paper bears the date 1904, it was published only in 1906.2 In the meantime, Bolles3 had presented his paper, " The Concentration of Gold and Silver in Iron-Bottoms." The raw material which formed the basis of the research was a matte containing Fe, 61.68, and Cu, 11.20

Jan 1, 1908

By F. S. Young

Previous laboratory and field experimentation has demonstrated the effect of several variables on drilling rate.1-5 These results have been incorporated into optimization theories6-" for the purpose of reducing drilling cost. Minimum-cost drilling theories rely on a combination of historical data and empirical prediction techniques for selecting optimum bit weight and rotary speed. Past solutions have required extensive use of computing equipment because of both the complexity of the mathematical formulations and the large number of parameters involved. Field attempts to apply these computed results have frequently failed because of the uncertainty of input data requirements. Humble has developed an on-site computer system to control bit weight and rotary speed and thereby implement the concepts of minimum-cost drilling. This system can (1) perform short interval drilling rate tests for formation evaluation, (2) use the results of these tests as input information to solve minimum-cost drilling formulas, and (3) control bit weight and rotary speed in accordance with these computed solutions. The purpose of this paper is to describe the computer control system and present results of initial field testing. Theoretical Considerations Minimum-cost drilling (MCD) requires a quantitative evaluation of the variables involved. Several forms of a basic mathematical model have been sug-gested.'?,' "he relationships reported here form the basis for the solution programmed in this work. Four equations are used, expressing drilling rate, bit bearing wear, bit tooth wear, and cost. A solution for minimum-cost drilling assuming constant bit weight and rotary speed over the entire bit life has been programmed for use in computing MCD schedules. This solution is subject to certain limiting assumptions such as those discussed by Graham et a1.I2: 1. Drilling cost is the summation of bit cost, rotating cost, connection cost and hoisting cost. 2. Diamond bits are excluded. 3. Bit life is limited by either bearing failure or tooth wear, or by a combination of operational factors that make it cheaper to pull an incompletely consumed bit. 4. Circulating hydraulics are adequate and do not limit drilling rate. 5. Bit weight considerations exclude hole deviation. 6. Drilling rate is a function of only bit weight, rotary speed, and degree of tooth dullness; that is, the effects of pressure, lithology, fluid properties hydraulics and drill string dynamics are ignored. In equation form, the four MCD expressions are as follows:

Jan 1, 1970

By J. F. Havard

The enterprises based upon the industrial minerals are diversified in geologic habit, mining systems, processing techniques and marketing methods. Nevertheless, in 1972 these enterprises faced many of the same frustrations and hopes and knotty problems and crucial decisions. Volume and profits were generally improved but were uneven in extent and effect. The U.S. cement industry, for example, was unable to meet demand in major markets. It was constricted by a frozen low-level price structure, faced expensive pollution control measures and watched heavy imports penetrating its markets from several European nations, Mexico and Canada.

Jan 1, 1973

By P. D. White, J. T. Moss, J. S. McNiel

Results of experimental work on the in situ combustion process were first published in this country in 1953' when Kuhn and Koch described results of a three-well test in Jefferson County, Okla. Shortly there-after Grant and Szasz2 described field studies in Nowata County, Okla., in which several modifications of the basic combustion process were investigated by injection of various oxidizing gas mixtures other than air. In the past five years speculation concerning this method of oil recovery has continued, with a number of interesting papers on various aspects of in situ combustion appearing in the literature3,4,5,6,7. However, only one of these' provided actual engineering information on pattern-type field experiments. The primary objectives of the Oklahoma three-well test were to check operation of specially designed electrical ignition equipment and evaluate problems associated with initiation of combustion in a natural oil sand reservoir. Immediately following successful completion of this test in the Pontotoc sand, plans were activated for a second field experiment to be conducted in the same sand a short distance away. The objective of this second field test1 as to establish a relationship between field observations and information derived from laboratory experimentation and computations. Secondary objectives of the test were to develop operating tech- niques and define operating problems, and to obtain information that would assist in the economic and engineering appraisals of the process. Careful planning was required since this test was designed with the hope of providing basic information on the characteristics and operation of a combustion drive. It was necessary to include test facilities which would not only permit precise control and measurement of the process variables but would also provide sufficient flexibility of control to insure that variables in the combustion process could be studied during the course of the test under a wide range of conditions. In order to accomplish these objectives elaborate instrumentation and several control wells were included in the design of the test installation. This type installation was felt to be well suited for an experimental study, but was in no respect intended as a counterpart of a commercial-scale operation. PRELIMINARY LABORATORY WORK An important objective of the field experiment, as stated previously, has been to obtain reliable data on operating variables which might be compared with similar data obtained in laboratory combustion tests. The value of successful correlations between quantities that can be measured in the laboratory and those obtained in a full-scale commercial venture has been well established for other industrial processes. The difficulty of following a process underground should make such correlations even more essential here. Also. approaching the field test phase of development of in situ combustion, it was considered desirable to precede design of test equipment with laboratory combustion studies under a variety of conditions to establish likely ranges of variables. These included temperature, air injection rate, frontal advance rate and produced gas composition.

By W. L. Saunders

(Wilkes-Barre Meeting, June, 1911.) I. INTRODUCTION. IT is now generally admitted by experts that at least so far as rapid progress is concerned the Alpine system of tunnel-driving is superior to any other. This is perhaps natural in view of the record of experience in driving tunnels through the Alps. These great mountain-chains cannot be treated in the ordinary way by shaft-sinking and driving headings, thus multiplying the points of attack. The work must be done from the ends only, hence speed in driving is of the utmost importance; and, as necessity is the mother of invention, the concentration of effort to make progress has resulted in an organization and in mechanical appliances that have produced results so much in excess of the usual practice, even in America, that a discussion of the subject in detail should be of much value to the engineer and contractor. The first Alpine tunnel was the Mont Cenis, length 7.5 miles, driven with a progress that averaged about 7.75 ft. per day. Next came the Saint Gothard, 9.5 miles long, 18 ft. per day; Arlberg, 6.5 miles long, 27.25 ft. per day; Simplon, 12.25 miles long, 36 ft. per day. The figures represent progress when driving from two headings, so that by dividing them in two we get the daily single-heading progress. The latest of the Alpine tunnels is the Loetschberg, now being driven. In this work the world's record has been beaten by a single day's record in one heading of 36 ft. and by an average daily record in. one heading of 29.5 feet. The Alpine range forms a natural barrier between a large section of northern and southern Europe. This range extends from the southeast of France to the frontier of Hungary, between Italy and the plains of southern Germany. The contour

Jul 1, 1911

By Donald F. Hammer, Donald W. Peterson

The Magma mine at Superior, Arizona, has produced over 13 million tons of ore yielding 1.5 billion pounds of copper. It is a mesathermal deposit, and, although the bulk of the ore has come from the Magma vein, most of the recent production has come from replacement deposits in limestone. The mine lies in a Precambrian and Paleozoic sequence of rocks that includes schist, diabase, quartzite, shale, and limestone; nearby, these rocks are intruded by igneous bodies of Mesozoic age that were probably the source of the ore-bearing fluids. Locally, these rocks are overlain by Cenozoic volcanic rocks and conglomerate. Layered rocks at the mine dip eastward about 30°. The area is extensively faulted, and surface faults are grouped into an earlier east-trending set and a later northtrending set. An additional set of diagonal faults that trends northwest and northeast is recognized underground. The east-trending Magma vein-fault, with its splits and branches, is the principal mineralized structure of the district. The bulk of the ore occurs in large ore shoots that plunge steeply westward and are sporadically connected by irregular ore shoots dipping gently eastward. The main ore controls apparently are selective zones of permeability related to the transverse faults. A bed of crystalline limestone near the base of the Martin Limestone (Devonian) is the host for the replacement ore bodies-discontinuous tabular pods dipping eastward parallel to the bedding. Selective permeability is again the apparent ore control, caused both by local hydrothermal solution of limestone and by deformation along faults. The principal copper minerals in the vein are chalcopyrite, bornite, enargite, tennantite, chalcocite, and digenite; these minerals vary in abundance according to a distinct zoning pattern. The upper part of the mine yielded considerable zinc as sphalerite, and the oxidized zone was rich in silver. The chief gangue minerals are pyrite, quartz, and hematite. In the limestone replacement bodies, chalcopyrite and bornite are the chief ore minerals.

Jan 1, 1968

By William Campbell

(Cleveland Meeting, October, 1912.) [SECRETARY'S NOTE.-To avoid repetitions of foot-notes, references to authorities are made in the paper by means of figures, referring to a numbered list in the appendix.-J. S.] I. INTRODUCTION. IN the olden days the making of alloys was au art, and the secrets of the craft were jealously guarded. To-day it has become a science, though the old ideas in regard to the secrets and formula are dying hard. Modern progress may be attributed to scientific research and testing of materials, and the substitution of chemical analytical control for " cook-book " methods. We know to-day a great deal about the constitution of alloys, the reasons of the change in structure and physical properties by heat and mechanical treatment; and this new knowledge is due for the most part to the physical chemist and metallographist, who have shown us that alloys are simply solutions, and as such obey definite laws. The application of the theories of solutions and of the phase rule tells us what ought to happen when our alloys are in a state of equilibrium. The working-out of the temperature-composition diagram (thermal diagram) for numerous alloys has thrown a light on the structure and constitution which has dispelled most of the darkness in which we labored before the advent of metallography. The work began with the determination of the freezing-point curves, and here the research of Le Chatelier,1 Gautier,2 Roberts-Austen,3 and the other pioneers broke the ground. Next the physical chemists, Tammann,4 Rooseboom,5 Bancroft,6 and their colleagues, showed us the complete thermal diagram and its meaning. Then the researches of Heycock and Neville 7 on the Cu-Sn series and of Shepherd 8 on the * Associate Professor of Metallurgy, Columbia University in the City of New York.

Dec 1, 1912

By H. Conrad

The strain hardening associated with the creep of magnesium single crystals at room temperatu.Je was investigated by shear tests in which the direction of stressing was reversed a number of times after creep in a <100> direction. The strain hardening was strongly anisotropic; the largest amount occurring in the direction of flow and the least 180 deg to this. The time law for creep changed from a parabolic type to logarithmic for the first and subsequent reversals of stress. For a given stress the creep strain decreased significantly for the first and second reversals and then only slightly for subsequent reversals. The logarithmic creep constant a changed in a similar manner. A linear relationship was observed between the creep strain for a given reversal and the stress. The slope for the third reversal yielded a strain hardening coefficient 12 to 16 times greater than that observed for unidirectional flow. Al-though no recovery was observed upon resting at room temperature, the hardening resulting from stress reversals could be completely removed by heating to 450" C. PREVIOUS work1.&apos; indicated that the creep rate of magnesium single crystals tested in the temperature range of 78" to 364°K decreased with time. This was attributed to an increase in internal stress resulting from an accumulation of dislocations at internal obstacles. The object of the present investigation was to further evaluate the nature of this hardening by conducting tests in which the direction of stressing is changed after previous creep in shear in a given slip direction. Previous to 1950 three investigations indicated that a Bauschinger effect3 occurred for single crystals as well as polycrystals brass in tension compression,

Jan 1, 1960

By T. C. M. Pillay, John Chipman

The Si-0 equilibrium in liquid iron was investigated in some detail by Gokcen and Chipman1 who reported equilibrium constants of the following reactions: In each case the thermodynamic equilibrium constant K was obtained by extrapolating K&apos; to infinite dilution. Their results on reaction [I] were consistent with those of earlier observers, and there seems to be little doubt as to the approximate validity of the equilibrium product determined. On the other hand, the results on reactions [2] and [3] indicated unusual curvilinear relationships between the activity coefficients of silicon and of oxygen and the silicon concentration. Since a linear relation is observed in all other similar instances, it was concluded that some source of error had affected the gas-metal equilibrium relationships. Recently the authors undertook a restudy of these equilibria with the view especially to establishing the equilibrium constant of reaction [2]. Their experiments, however, were discontinued before a tbroughly satisfactory answer had been obtained and consequently have remained unpublished until the present time. Quite recently Matoba, Gunji, and Kuwana2 published the results of a very thorough study of these equilibria. It is the purpose of the present note to Compare these three sets of experimental data, a comparison which leads to Confirmation of the results of Matoba and coworkers. The experimental arrangements described by Dutilloy and Chipman were employed. A controlled mixture of Hz, H,0, and argon was led into the induction furnace over the surface of the Fe-Si melt contained in a silica crucible. On account of the slow approach to equilibrium, runs were continued for at least 8 hr and, in some cases, as much as 12 hr. Samples were taken by means of silica tubes at the start and during the final 4-hr period of each run. Out of twelve runs only seven appeared to have approached equilibrium with sufficient certainty to be reported here. The results of these experiments, all at 1600°c, are shown by the triangles in Fig. 1. Equilibrium was approached from both oxidizing and reducing conditions and the direction of approach is indicated by the shape of the triangle. Attempts to extend the study to higher silicon concentrations were unsuccessful on account of the transfer of silica from the metal bath to the upper portions of the crucible by means of a silicon-monoxide mechanism. Matoba, Gunji, and Kuwana used similar methods and approached equilibrium from both sides. Their results at three temperatures are shown by the solid lines of Fig. 1. A line corresponding to 1600 deg is interpolated from their equations and is shown by the dotted line. The results of Gokcen and Chipman at 1600 deg in the range 0.02 to 2.0 pct Si are also shown. At concentrations up to about 0.6 pct Si, these investigators approached equilibrium from both directions, and their results in this range appear to be trustworthy. Above 1 pct Si, however, all of their experiments involved oxidation only, as shown by a decrease in the silicon content of the bath. It now seems certain that they failed to reach equilibrium at these higher silicon concentrations and that the curvilinear relation shown by their results is incorrect. It is evident that their results in the lower silicon range are in good agreement with those of Matoba and coworkers. In fact, a straight line drawn through their results would parallel the dotted line and would differ from it by only 0.05 in log K. The new data also lie close to that line. It may thus be concluded that the three sets of data are in good agreement and that the equations proposed by Matoba and coworkers for reaction [2] are satisfactory . They take the limiting value of log K&apos;, at 0 pct Si as log K ,. The slope of each line gives the value

Jan 1, 1962

By George F. Becker

(San Francisco Meeting, October, 1911.) A MERE record of Emmons&apos;s professional career would very inadequately represent the man. That he was eminent we know, and our successors will realize in due time; but they must depend upon us for knowledge of a singularly wholesome, modest, unselfish personality, and of a character that did honor to a profession in which trustworthiness is indispensable: Those members of the Institute who met Emmons are his friends, and I never knew one of these who was not the better for that friendship. Emmons was born in Boston, Mar. 29, 1841, the son- of Nathaniel H. and Elizabeth (Wales) Emmons, and was named Samuel Franklin after an ancestor who was of the same family as Benjamin Franklin. He took the degree of Bachelor of Arts at Harvard in 1861, and soon afterwards went abroad to complete his education. From 1862 to 1864 he attended the courses at the École Impériale des Mines at Paris, lie e Beaumont and Daubrée being among his professors. The year 1864-1865 he spent at Freiberg under Cotta and other famous teachers; after which he spent another year in traveling through Europe. Like many other renowned geologists, he approached his ultimate profession from its economic side, and was thus from the first imbued with a sense of high responsibility in the promulgation of scientific opinions or conclusions. With hypotheses which were interesting merely because. they were ingenious or even plausible, he would have nothing to do. In 1867 he joined the Geological Exploration of the Fortieth Parallel at its organization under Clarence King, serving at first as a volunteer, but soon receiving a regular appointment. This expedition was the first one of purely geological character sent out by the United States Government. As Emmons has shown in his admirable presidential address on " The Geology of Government Explorations," its work was founded on a com-

Sep 1, 1911

By J. E. Campbell, A. W. Wesner, M. Pobereskin

This paper summarizes the results of an investigation sponsored by The Coates Steel Products Company. The objective was to determine the relative effects of certain chemical and physical properties on the wear resistance of grinding balls when grinding cement. In making this study, a number of types of balls were used in both dry and wet grinding in commercial ball mills. The radioactive-tracer technique was used in separating the test balls from the rest of the mill charge and in sorting the different types of halls that were all tested at the same time for each of the grinding operations. PROCESSING OF GRINDING BALLS In order to determine whether the properties of grinding balls, namely, composition, microstructure and hardness, can be related to the rate of wear, the halls used in this study were selected to represent various combinations of these properties. It was recognized that the mechanism of wear was not the same in the wet mill as in the dry mill. Therefore, the types of balls tested in each of the two environments were not necessarily the same. However, all of the types of balls evaluated in the dry mill were tested simultaneously for one time period, while those evaluated in the wet mill were tested simultaneously for three different time periods. All of the test balls were separated from the charge when the mill was dumped. All of the balls were of 0.940-inch diameter when charged, and all but the regular production balls were finish ground to this size to eliminate the decarburized surface layers. The steels and processing methods used, as well as the micro-structures and hardness levels of the balls, are described as follows: Regular production forged SAE 1095 steel balls were used in both the wet and dry mills. They were forged to a nominal diameter of 0.940 inch and quenched in oil from the forging temperature. Each retained a partially decarburized surface layer from the forging bar stock; the maximum depth of this layer was about 0.030 inch and the decarburization was negligible where the ball was sheared from the bar. The hardness at the surface was 40 to 46 Rock-well C in the partially decarburized area and 57 to 62 Rockwell C in the areas not decarburized. The hardened zone extended to a depth of about one-third of the radius. Below the decarburized layer, the hardened zone consisted primarily of hard as-quenched martensite with varying amounts of retained austenite. This structure changed to fine pearlite at a depth of about one-third of the radius. In order to eliminate the effect of the decarburized layer, a set of production balls of SAE 1095 steel was forged to about a 1-inch diameter, quenched in oil from the forging temperature, and ground on ball-bearing grinding equipment to a 0.940-inch diameter to remove the decarburized layer. The balls&apos; hardened zones were similar to those in the previous set. The hardness of the finished surfaces was 52 to 60 Rockwell C. A slight amount of decarburization apparently remained after the removal of about 0.030 inch from the surface. Balls of this type were tested in the dry mill only. Another set of forged SAE 1095 steel balls of 1-inch diameter was heated to 1500 F and quenched

Jan 1, 1961

By Edward Capillon

THE problem of scrap is probably of greater importance inn the production of gold, silver and other precious metal alloys than is the case for base metals and alloys. Remelting of gold and silver scrap in the shop is always a costly process because it involves losses by oxidation of the base metals in the alloy with a consequent increase in the percentage of precious metal. This is most marked in the case of alloys containing the low-boiling and easily oxidized metals zinc and cadmium. Since it is. not generally feasible to assay every shop remelt it follows that the possibilities of lost values are large. So-called rolled gold and silver plate is made by soldering or welding the precious metal alloys onto base, metal. Such plate when defective must be sent to the refinery to recover the gold and silver values, thereby involving additional expense in the form of refining charges. It is obvious therefore that gold and silver alloy scrap is an important item in manufacturing cost and must be reduced to a minimum. The amount of scrap resulting from poor metal will depend on a number of factors in the manufacturing operations, not least among which is the melting and casting practice. The notes which follow are a summary of experiments performed at various times to determine what variables in melting and casting are influential in the production of sound alloys.

Jan 1, 1930

By L. F. Stutzman, George Thodos

A new graphical method, which is a modification of that proposed by Buckley and Leverett&apos;, is presented for the determination of the displacing fluid saturation at breakthrough for frontal drive mechanisms. This method is applicable to all types of fluids, which may be either soluble or insoluble in the oil at reservoir and injection conditions. This adaptation has unique advantages in handling problems in which either liquids or gases are the displacing fluids. INTRODUCTION In the displacement of oil from a reservoir with water or gas injected into the formation or by the expansion of a gas cap, the determination of breakthrough or flood advance is important to define the initial and subordinate phases of the operation. Thus, the determination of the displacing fluid saturation at breakthrough is fundamental to the establishment of over-all reservoir production. Methods for analyzing this saturation and for calculating production rates have been previously reported1,&apos;*".". All of these methods utilize the rate equation for linear flow developed by Buckley and Leverett1. xs = QT - Qn/A? (?fu/?Su) .....(1) Sp where f, represents the volumetric fraction of displacing fluid in the total flowing fluid within the reservoir as is defined by: fo = 1/1+ ku/kd µn/µn .......(2) Since the time, ?, necessary for the flood front to travel distance ?X is unknown, Eq. 1 cannot be solved directly for the determination of the breakthrough point. Therefore, it becomes necessary to solve Eq. 1 simultaneously with an equation representing a fluid bal-ance on the reservoir behind the flood front. To develop such a fluid balance equation, it has been assumed that the fluid composition is uniform in the reservoir behind the flood front. Based upon this assumption, the follow-ing equation can be derived from a material balance on the displacing fluid: x = (?X) s Dx ? x=0 [ Snx - Sn1 ] dx = QT - Qn/A? It is readily observed that the displacing fluid satura-tion behind the flood front, Snx, may be determined through the simultaneous application of Eqs. 1 and 3. Although the approach may vary, this objective re-mains the same for all of the previously mentioned graphical or analytical methods. After Sox is determined, it is then possible to calculate the gas-oil and/or water-oil ratios and the rates during the initial and subordinate phases of production, and thereby define the production history of the reservoir. In this presentation only the de-termination of Snx is considered, and the reader is re-ferred to the several texts in reservoir engineering2,4,5 for a complete discussion on the methods for establish-ing the production history of a reservoir. PROPOSED METHOD FOR DETERMINING Snx Since at any time the quantity, QT - Qn/A? is a constant, Eq. 1 may be expressed in differential form as follows: dxsn = QT - Qn/A? d (? fn/? Sn) sn .....(4) Eq. 4 may be substituted directly into Eq. 3 to obtain: ? fn/? Sn ? [ Snz - Sn] QT - Qn/A? d ( ? fn/? Sn) = QT - Qn/A? ...............(5) Eq. 5 simplifies to the expression: ? fn/? Sn ? [ Snz - Sn] QT - Qn/A? d ( ? fn/? Sn) = 1 ....(6)

Jan 1, 1958

By J. Mason

In order that the use of continuous mining machines be most economic, the equipment must be operated at rated capacity as much of the time as possible and downtime for repairs kept at a minimum. A large factor influencing any proposals for maintenance programs is the complexity of the machines—often the intricacies of the precision-built equipment requires engineering knowledge byond the scope of mine maintenance personnel. A training program is part of the answer; there are others. In addition to investigating a joint company-manufacturer equipment-design improvement program, Mountaineer Coal Co. has launched a detailed preventive maintenance program to combat extensive downtime often encountered when continuous miners are used. Everyone in the coal industry knows the importance of operating continuous miners at their rated capacity as much of the time as possible. The potential capacity of the miner is such that l-min. delay means from 3 to 8 tons of coal lost. Today&apos;s miner is a well designed, precision-built machine, complicated with hydraulic and electrical equipment and complex mechanical assemblies with all possible combinations of gears, levers, and rods. As the machine becomes more complex, the problem of maintenance becomes more acute. The transition from conventional to continuous mining has taken place so rapidly that the mine mechanic has been unable to keep pace. When there is a machine failure, the maintenance man usually employs either the trial-and-error or the play -it-by-ear method of repair, but this represents an expensive proposition. Mine mechanics, maintenance superintendents, and mine managers complain about the complexity of the machines and how difficult it is to keep them running. There is no shortage of skill in the design offices. Machines are designed by good engineers, but for engineers. What&apos;s the answer? Better trained maintenance men—better maintenance instruction—better field service. These are all good corrective measures, but the real cure is to provide for the men at the do it level. Designers have got to cooperate with men to simplify maintenance on the increasingly complex machine. The designer must be aware of how his machine can be maintained. Sometimes a simple design change in a bearing, oil seal, or a bushing will correct recurrent breakdowns. Parts such as filters, hydraulic cylinders, hoses, and pivot pins can be better arranged on the machine to make them accessible so that the mine mechanic can easily keep the machine producing. Therefore, to get our maintenance off on the right foot, the program must begin back in the design office, before the machine is delivered to the mine property. Realizing the importance of this aspect, our company set out on a joint company-manufacturer equipment-design improvement program. This is a formal program in which quarterly reports are written covering machine defects, design weakness, and general problems relating to machine maintenance and performance. The manufacturer in turn comments on each and every item appearing in these reports, indicating the action he proposes to take. In addition to the written reply, meetings are scheduled with manufacturer representatives to discuss further the outlined problems. The benefits realized from this organized program are both substantial and far reaching. Good maintenance begins with a good design. The subject of preventive maintenance is not a new one. Volumes have already been written on the subject. It consists primarily of doing the maintenance work when you want to rather than when the machine demands it. However, a preventive maintenance program can be overdone. Theoretically, if carried to ridiculous extreme, all working time could be spent inspecting and repairing the machines and no time would be left for production output. Our goal in maintenance is to maximize running time for all machines, and to prevent or at least minimize production downtime. INSPECTION AND REPORTING The center of any preventive maintenance schedule is regular and systematic inspection, but it must be

Jan 1, 1961

By F. W. Bowdish

A theoretical and experimental laboratory study has shown that the rate of breaking of oversized particles in a ball mill is proportional to 1) the concentration of such particles, and 2) the area of the balls, provided that the balls are larger than a certain size relative to the particles. If all undersized material were removed as formed, the rate of breaking would be almost independent of the quantity in the mill. Rate equations are given which are similar to those for zero, first, and second order reactions. Deviations of small balls from the equation for a second order phenomena are quantified by a factor called "nipping efficiency." Some data are correlated by a dimension-less equation, which is used to estimate nipping efficiencies from data not in the correlation. The investigation described here was undertaken after a literature survey revealed that little was known concerning the mechanism of breaking of particles within a ball mill and the effect of this mechanism upon grinding rates. One paper, by Roberts1 , offered a theory concerning the mechanism of breaking, and a rate equation for the breaking of particles larger than some size to particles smaller than that size. That paper provided the starting point for a theoretical and experimental investigation of grinding under carefully controlled conditions. THEORETICAL CONSIDERATIONS In his paper on the probability theory of ball mill grinding, Roberts theorized that "... a given expenditure of power leads either to a certain number of point to point blows per bp-hr or to a certain distance of line contact per hp-hr ..." He assumed that the balls touch each other during each blow or during moving contact. Then he said that a volume of pulp, dependent upon the size being considered, would be covered per minute within which all oversized particles would be crushed to particles smaller than that size. Naturally, the higher the concentration of oversized particles in the pulp, the higher the rate of which they would be broken. From this reasoning Roberts obtained the differential equation -dC/dt = k hp/ton C (1) where k is a constant for any size of particle, density of particle, and moisture content of pulp. C is the percentage of oversize in the material to be ground, t is the time, and hp/ton is the power input per ton of material in the mill. He then integrated the equation to log Co/Ct = k/2.3 hp/ton t , where Co and Ct are the percentage of oversize at time zero and t respectively. By always using the same quantity of material in a mill and assuming that it required constant power to run the mill, he was able to combine the horsepower per ton factor with the other constants to give an equation for a first order rate.

Jan 1, 1961

By T. R. A. Davey

The fundamental principles by which bismuth may be removed from lead by pyrometallurgical processes are enumerated. Qualitative discussion of the phase diagrams concerned is followed by presentation of quantitative diagrams. Brief mention is made of the practical aspects. Data presented show how chemical lead (<0.005 pct Bi) may be produced by the Jollivet, Dittmer, and Kroll-Betterton processes. BISMUTH is an element whose properties are very similar to those of lead, and its minerals are associated to a greater or lesser extent with nearly all the major lead ore deposits of the world. In consequence, the lead produced contains bismuth unless a special debismuthizing process is practiced. There does not appear to be any published comprehensive review of the effect of bismuth as an impurity on the properties of lead, and there is some uncertainty as to the beneficial or detrimental effects of small amounts of bismuth in lead used for particular applications. Standard specifications of most countries stipulate a maximum bismuth content of 0.005 pct for chemical lead. With one exception, this specification is met only by lead producers whose ores are relatively bismuth-free, or whose refineries are electrolytic. In lead for certain applications a higher bismuth content is preferred by some fabricators.&apos; In contrast to the refining for silver, copper, and antimony, the refining for bismuth does not usually result in a large overalil economic gain from the sale of byproduct. Thus, debismuthizing is customarily practiced only if market conditions demand a lead with a bismuth content lower than that produced by classical refining; i.e., softening, desilverizing, and zinc refining. Until this century, debismuthizing was carried out only a:; an incidental result of desilverizing, as later described. This century has seen the development of the Betts electrolytic process—the only successful one of many electrolytic processes proposed and patented —and a number of precipitation processes based on the pioneering work of Kroll,&apos; although only one of these, the Kroll-Better ton process,&apos; is in wide commercial use today. It is proposed in this paper to deal only with the pyrometallurgical processes, excluding those based on aqueous electrolysis. Historical Background Prior to 1833 silver (and incidentally bismuth) could not be removed from lead. To recover silver from rich bullion, the only course available to lead refineries was to cupel the bullion, forming a slag of litharge. The first slag tappings or skimmings, on reduction, yielded soft lead of very low silver and bismuth contents. Intermediate skimmings yielded a lead of somewhat higher silver and bismuth contents, which could if desired be recupelled. The last skimmings yielded a litharge very high in bismuth, which could by successive oxidation and reduction cycles be separated into high purity bismuth, and lead returns. This oxidation reduction process, with modern operating techniques, can still be used today to produce a portion of a lead refinery&apos;s output of very low bismuth content, as discussed later. In 1833 Pattinsone discovered that lead bullion could be purified of silver and bismuth by fractional crystallization, the primary lead crystals formed by partial freezing being purer than the melt. Repeated processing in pans produced a lead containing as little as 0.02 pct Bi. The simple explanation of this

Jan 1, 1957