Search Documents

By Leo D. Jones

The use of the centrifuge for dewaxing lubricating oils grew out of the effort to secure better results than had been attained by the common "cold settling" process. This process was the only known method for dewaxing steam refined cylinder stock (600" F. fire test), the product known as "bright stock" being commonlyused for building up "pressed," i.e., dewaxed neutrals of, say, 200-sec. viscosity [to a higher value. The process consisted of mixing the cylinder stock with approximately one and one-half times its volume of naphtha, heating, to dissolve completely all the oil and wax and then slowly chilling to about 15" F. in large insulated tanks. This caused the wax to precipitate. It was allowed to settle out by gravity. The supernatant liquid was then drawn off and the naphtha distilled off, leaving a still residue of bright stock. The sediment from the settling, of a slushy nature, was withdrawn. After removing the naphtha by distillation the residue was petrolatum. At some point in the process, preferably after the dilution but before chilling, the mixture was decolored by percolation through fuller's earth. The finished bright stock produced by this process had a cold test of about 50" F. Efforts to improve this by chilling to a lower temperature resulted in a considerable reduction in yield, and increased uncertainty of settling. Even when chilling to 15" F. it was not uncommon to find that after a week's waiting a tank had not settled. It was then necessary to heat and rechill. This uncertainty was a serious problem; in one case a refinery superintendent had men riveters hold pneumatic hammers against the tank for hours, hoping thus to cause agglomeration and settling of the wax. Yields of bright stock above 70 per cent, were uncommon. History of Centrifugal Application It is not surprising, therefore, that many attempts were made to improve upon the results obtained by cold settling. George H. Taber, vice-president of the Gulf Refining Co., Pittsburgh, Pa., made a number

Jan 1, 1924

Jan 7, 1976

By Ralph Hultgren, Bernard York, David W. Mitchell

It is a well-known fact that magnesium-alloy castings are apt to be coarse grained if the melt is not superheated several hundred degrees above the melting point before casting. (The casting temperature varies according to the shape of the mold. A typical casting temperature is perhaps 1400°F.) British practice is to heat to 900°C. (1650°°F.) for 15 min., cool rapidly to casting temperature, and cast.1 In Germany superheating is carried out at 850° to 900°C. (1560° to 1650°F.) depending on the amount of scrap used. It is stated that further refinement will be obtained by prolonging the period of superheating or by increasing the superheat temperature to 950°C. (1740°F.).2 In the United States superheating is carried out at i600° to 1700°F. (871° to 927°C.), perhaps even higher in some places. It is stated that superheating effects are found as low as 1500°F. (816°C.), but several hours are required.3 These commercial treatments lead to grain sizes in sand castings that may vary from 4 to 8 grains per sq. mm.§ in heavy sections and from 60 to l00 in 3-in sections to perhaps 380 in thin sections. It is also generally known that the refining effect of superheating is lost if the melt is held for some time at lower temperatures before casting. Aside from these very qualitative statements, there is little to be found in the literature as to the effect of temperature and time of superheat on the final grain size. Because of the uncertainty of these factors, the Office of Production Research and Development of the War Production Board placed a research contract with the University of California, supervised by the War Metallurgy Committee. This research, which was done under the "Restricted" Project NRC-550, is the basis of this paper, which has been released for publication by the O.P.R.D. The material studied was an alloy prepared from carbothermic magnesium. The temperatures required for grain refinement proved to be widely different from those used in practice, as described in the statements in the first paragraph. This difference is attributed to the fact that the magnesium in the specimens was of carbothermic origin instead of the electrolytic magnesium in common use. MATERIALS AND METHODS The magnesium alloy studied was one of the most popular sand-casting alloys, with a nominal composition of 9 per cent aluminum, 2 per cent zinc, and 0.r per cent (minimum) manganese and the balance magnesium. This is designated

Jan 1, 1945

By Norman C. Stines

Russia's mineral potential is a secret that has been effectively kept by the Iron Curtain. There is no conclusive data and because of its extreme importance to the Free World, the subject is greatly discussed. Opinions range from those presented by Paul Tyler in his article "Russia's Mineral Potential," June issue of MINING ENGINEERING to those of Norman C. Stines, presented herewith. Mr. Stines is a consulting mining engineer of Los Gatos, Calif. He was in Russia, China, and Manchuria from 1909 to 1918 as a mining executive. From 1917 to 1919 he served as assistant military attache Intelligence Branch U. S. Army in Petrograd, Russia.

Jan 11, 1951

By H. R. Peiffer

Hardening of soft metals can be accomplished by dispersing finely divided hard particles in them. The dispersing of finely divided alumina in silver in the presence of oxygen yields a high strength material which is unusual in that its mechanical properties above the melting point of the continuous Ag-O alloy matrix are similar to other solids. The tensile strength is studied for two of these alloys, one of which contains 15 pct by weight alumina and the other 20 pct by weight alumina. The average fracture strengths above 960°C of these alloys were found to be 0.4 x106 dynes per sq cm and 3.8x106 dynes per sq cm respectively. The strengths appenred to be independent of temperature above 960° C. The creep behavior of the 20 pct alumina material was studied above 960°C. The initial creep rate, 6 , of this material can be represented by where s is the applied stress and E the activation energy for the process. This energy is of the order of 1.7 to 2.1 ev. HARDENING of soft metals by the addition of finely divided, hard particles has resulted in the production of materials with excellent creep resistance and with inhibited recrystallization.' It has been demonstrated that such composites have useful strength up to temperatures very near the melting point of the soft metals, but one might expect that the strengthening by the dispersed particles ceases to be of importance above the melting point of the softer phase. This, however, is not so.2 In this paper the strengthening of a liquid Ag-O solution by the presence of dispersed alumina is discussed and experimental data concerning the mechanical properties of such a material at temperatures above 960°C presented. EXPERIMENTAL PROCEDURE Specimens were prepared using powder metallurgical techniques. Finely divided silver oxide was mixed in the appropriate proportions with "Linde B" alumina. For these experiments the specimens contained 15 or 20 wt pct alumina in pure silver.* These alloys were used in these experiments since they were the ones that could be handled readily enough to yield experimental data. Silver oxide was used in preference to silver because it is readily available in a very finely divided form and because the presence of excess oxygen in the silver is important to the properties2 of the material. The powders were mixed wet, using alcohol as the medium, in an ordinary food blender until a uniform mixture was obtained. They were then dried and heated to reduce the silver oxide to silver. Only a fraction of the finely divided silver remains unoxi-dized upon removal from the oven since the finest particles of silver oxidize immediately upon contact with air. The remaining fine silver served as a binder during pressing. The mixture was then pressed at 20 tons per sq in. into shoulder-grip (reduced section 1/4 in. by l/4 in. by 1 1/4 in.) and rectangular bar specimens (l/4 in. by 1/4 in. by 2 in.). The green specimens were heated very rapidly in a globar furnace to 1000°C, held at temperature untic they had reached theoretical density and then furnace cooled. The strength of the two compositions at temperatures above 960 °C was determined by pulling shoulder grip specimens inside a furnace mounted on a tensile machine. Specimens were gripped by means of wires wrapped around the shoulders of the specimen. Temperatures were measured by means of a chro-mel-alumel thermo-couple placed in the vicinity of the specimen. Control of temperature (within ±°15C) was accomplished by means of a Weston Recorder-Controller. Before loading, specimens were held at temperature for approximately 15 min in order to insure uniform specimen temperature. The low loads were measured by a special load cell designed by Baldwin Lima Hamilton. All testing was performed on a FGT testing machine of the same com-pany. Creep studies were performed in bending utilizing rectangular specimens of the 20 pct alumina alloy. Specimens supported at both ends by knife edges of inconel were placed in a globar furnace, heated quickly to temperature, and the deflection of the beam measured optically as a function of time. The weight and size of the specimen were predetermined and the maximum stress on the beam calculated from

Jan 1, 1962

By Lane Mitchell

A ceramic product or processed material is a solid composed of materials which have been subjected to heat above 875°F. The raw materials, which are blended together (or in some cases used singly), are selected and utilized for various reasons such as ease of fabrication, aid to processing, to yield desired properties after processing, lack or controllable degree of toxicity or hazard, availability, cost, and perhaps other considerations. Almost all solid inorganic, some organic, and some liquid and gaseous materials have the potential to be used individually in some ceramic product. There are several fundamental functions to be fulfilled in every ceramic product and a number of secondary functions are desirable in specified products. These functions are generally met by the most widely occurring minerals and rocks of the earth and their debris. This fact characterizes ceramics as a field utilizing the raw materials most available to man. Of course, specified products utilize synthetics, organics, and rare inorganics to produce desired results. Any solid nonmetallic product processed by subjection to temperature above a red heat may be called a ceramic product. Widely used construction materials and units, domestic utensils and units, industrial parts to facilitate manufacture, technical components, and aesthetic creations are very often of a ceramic nature because of the durability, inertness, hardness, ease of fabrication, cost, and availability of the ingredients. Often, organics or metals cannot meet desired specifications for some of these products. The rocks and minerals and mineral debris of the earth are largely siliceous. Oxygen and silicon comprise roughly 75% of the earth's crust with aluminum, iron, calcium, and the alkalies following in abundance. Silica ( SiO, ) and silicates can be melted to form glasses. Alumina (A1,0,), present in a mineral com- pound, gives greater durability, hardness, and strength, but lessens the glass-forming property. Iron, calcium, and the other alkalies flux silica and reduce melting points. Thus, sand, which is generally almost pure SiO,, and clay, which is generally hydrated alumina silicate, are the most widely used of all ceramic raw materials-principally because of the glass-forming propensities of silicates. In ceramic formulations, clay is generally a refractory filler or skeletal material, having in the raw state a plasticity derived from its colloidal grain size and its water-loving nature. On the other hand, silica sand is a glass former or nonplastic filler. Clay and silica sand in pure forms are quite refractory, i.e., not easily melted. Clay, although siliceous, is less of a glass former than pure silica and is more refractory. Natural contaminants, such as iron oxide or limestone, adulterate many clays and some sands. These contaminants act as fluxes and reduce the fusion points of the mineral or blends. Glass is made from silica sand by fluxing the sand with strong bases, usually soda ash and limestone. Red building bricks are hard and durable because the sand and clay have been partially fused with help of natural iron oxide serving as a flux. The iron oxide per- forms a dual function, serving as a pigment as well as a flux. In a blend of clay and sand and iron oxide, the sand is more susceptible to fusion than is the clay. Although silica sand and clay are the most widely used raw materials in most ceramic products, many other minerals, and some non- minerals are utilized in products where these materials can produce or aid in achieving desired results. Limestone and dolomite, feldspars, pigmentary minerals, refractory oxides or carbides, and special property producers can

Jan 1, 1975

By F. Weinberg

INTEREST is currently being directed toward grain boundary morphologies in zinc in terms of grain boundary facetingl and grain boundary energies.' Some years ago the present author attempted to measure grain boundary energies in 99.999 pct purity Zn as a function of boundary angle, using the standard procedure of measuring equilibrium angles of the boundary traces at triple points. This followed an investigation he carried out on preferential melting of |H (112) Fig. 1—Electron transmission micrograph of a stacking fault, grain boundary intersection in copper. GRAIN BOUNDARY STACKING FAULT Fig. 2—Schematic representation of the intersection of Fig. 1, indicating inclination angles 0 and trace angles $. specimens were prepared by the Bollman technique in an electrolyte of 70 pct methanol, 30 pct HNO3 main-tained at -30°C. The interfacial free energy of the high angle grain boundary and of the stacking fault is assumed to be thermodynamically equivalent to the corresponding in-terfacial tensions. In terms of the true dihedral angles & between the intersecting interfaces, the equilibrium of interfacial tensions in the direction parallel to the stacking fault yields: ysF = -ygb(cos F1+ cos ±cosF2) Here, ysF is the stacking fault free energy and ygb is the grain boundary free energy, assumed equal on both sides of the intersection. Forces acting normal to the grain boundary, of the form ??gb/?F,l are assumed negligible as the grain boundary remains straight for a considerable distance on either side of the intersection. The micrograph of Fig. 1 may actually consist of several closely spaced stacking faults on the same slip plane. The actual point of intersection between the grain boundary and the first stacking fault, and the equilibrium configuration of the intersection, should not be affected by the presence of the other faults, as

Jan 1, 1970

By OTTO HERRES

TITANIUM is estimated to be the ninth most plentiful element, ranking after iron, aluminum, and magnesium, and ahead of copper, lead, and zinc. Vast quantities of titanium are widespread throughout the world in ore deposits and beach sands. Before the war, processing plants were operated in England, France, Italy, Czechoslovakia, Norway, Russia, Australia, United States, and Japan. In spite of its widespread occurrence, however, the U. S. Department of Justice has held the titanium industry to be a world monopoly and action was taken in the Federal court during the summer of 1945 to enjoin international patent and marketing agreements and to restore free competition. Possibly the rather surprising lack of public familiarity with this industry of international importance arises from its astonishingly rapid development and growth in the strong hands of some of the greatest chemical companies in the world, including the important foreign companies, Imperial Chemical Industries (British), Montecatini (Italian), I. G. Farben (German), and Titan Kogko Kabushiki Kaisha (Japanese). The rapid growth of the titanium industry in the United States is indicated by a tenfold increase of ore imports in the 1930 to 1940 decade before the war began to affect shipments from overseas. The fact that the industry formerly derived practically all ore for chemical processing in American plants from foreign sources probably also accounts for lack of general public knowledge of titanium. In 1939, to meet the requirements of increasing demand for the white pigment. titanium dioxide, more than 250,000 tons of titanium concentrates moved to this country, principally from the Travancore coast of India where the ilmenite concentrate from the beach sand runs as high as 60 per cent in titanium dioxide. Global warfare put a stop to shipping and thus gave rise to the development of titanium mining on a substantial scale in the United States during 1941.

Jan 1, 1946

By Martin Rubenstein

CdS crystals have been grown from a number of metallic solvents such as bismuth, tin, lead, and cadmium. Etching studies have shown that plastic deformation occurs if the crystals are not removed from the solvent prior to the solidification of the solvent, on cooling. The deformed crystals show a umique exciton fluorescence as a function of edge dislocation density. If one grows the CdS in the eutectic alloy of the above four metals (commonly called Wood's metal) the crystals can be removed from the solvent with hot water and no plastic deformation occurs. In this paper, the liquidus solubility measurements of CdS, as a function of temperature, are presented. The data were obtained using a high -temperature filtration technique. CADMIUM-SULFIDE crystals have been grown from a number of metallic solvents1 such as cadmium, bismuth, tin, and lead. Liquidus solubilities of CdS in cadmium,2 bismuth,3 and tin4 have already been measured. Crystals of CdS, in all four metals, have been grown by solution growth: 1) by cooling a saturated solution and 2) by a solution transport method.1'"1 CdS crystals grown in these four solvents have a few characteristics in common: 1) 1.8°K photolumines-cent emission consisted mainly of the radiative recombination of the bound exciton commonly known as I,, 2) slip lines which could easily be seen by the naked eye, and 3) edge dislocation densities in the order of l05 per cu cm.1 It was decided that these slip lines and the high edge dislocation densities were caused by a plastic deformation of the CdS crystals. It was felt that this plastic deformation did not occur during the growth of the crystals nor during the cooling of the solution, but did occur when the solvent which was in contact with the crystals froze. If these assumptions were valid, the slip lines and the high number of dislocations could be reduced or eliminated by removing the crystals from the solvent before the solvent froze. Since crystals of CdS had already been grown separately in such solvents as bismuth, lead, tin, and cadmium, it was felt that crystals could be grown in a eutectic mixture of these four metals. In this work a eutectic (or near eutectic) mixture of bismuth, lead, tin and cadmium in the proportion 50, 26.5, 13.5, and 10 wt pct, respectively, was used to grow CdS crystals. Such a mixture has a melting point of about 70°C and is close in composition to the alloy commonly known as Wood's metals. If the crystals could be grown from this mixture of solvents, and if hot water (>75°C) could be used to separate the crystals of CdS from the metallic solvent, it was hoped that CdS crystals could be grown with little or no plastic deformation which had been ob- served when crystals were grown from these solvents uncombined. CdS crystals were grown from this low melting eutectic mixture of bismuth, lead, tin, and cadmium using the solvent transport method. CdS powder and the appropriate amount of metals were sealed in a quartz tube under a pressure of about 5 X 10-6 torr. This ampule was then placed in a vertical position in a furnace. The temperature was raised to about 900°C. The furnace was designed so that the top of the liquid column within the ampule was between 10° to 40°C higher than the bottom of the liquid column. These temperatures were measured on the outside of the quartz ampule. The ampule was maintained at temperature for 7 to 14 days (depending on the temperature at which transport was taking place) and then the furnace temperature was lowered until the temperature was about 125°C. The ampule was then removed from the furnace, placed in water maintained at about 90°C, and opened in this 90°C environment. The crystals could then be removed from this two-phase liquid (Wood's metal and water) by mechanically picking them out. Alternatively, the crystals could be quantitatively removed by adding an excess of mercury to the mixture of metals, crystals, and hot water. The hot solution of metals and the hot water could be evacuated using a small diameter tube connected to a vacuum. Small amounts of mercury and water could be removed by heating the crystals in vacuum. Crystals prepared using this technique showed no evidence of slip. However, some of these crystals did show edge dislocation densities as high as l04 per cu cm. Some few selected crystals showed no dislocations. Single crystals of CdS were grown as large as 5 by 5 by 0.5 mm. The ampules for the growth of these crystals were 13 mm O.D., 11 mm I.D., 150 mm! LIQUIDUS SOLUBILITY MEASUREMENTS The CdS starting materials was G.E. 118-8-2 powder which was fired in H2S at 1000°C, and then a vapor transport technique5 was applied to produce a "sound" mass of CdS. The Wood's metal was prepared by weighing out bismuth, lead, tin, and cadmium in the proportions of 50, 26.5, 13.5, and 10 wt pct, respectively. The bismuth, cadmium, and lead were from the American Smelting and Refining Co. (ASARCO) and all had purities of 99.999+ pct. The tin was 99.9999 pct spectroscopic grade from the Vulcan Materials Co. The appropriate mixture was placed in a quartz tube, evacuated to a pressure of 5 X 10-6 torr, melted to a liquid, cooled to room temperature under this same vacuum. This ingot was then placed in another quartz tube, evacuated to 5 x l0-6 torr, and sealed off under vacuum. The ampule was then horizontally placed in a furnace. The temperature was raised to 600°C, and over a period of several hours the ampule was vigorously shaken several times. The ampule was then removed from the furnace, and the metallic liquid was

Jan 1, 1970

By Frederick G. Bulkley

That portion of the geological structure of the Leadville district which rests upon the Archæan is made up of sedimentary beds of Silurian and Carboniferous formation, consisting of many conformable strata of limestones, quartzites, and shales, which have a total present thickness of about five thousand feet. Interbedded with these strata are found, under somewhat fixed lams of regularity, sheets of intrusive igneous rock,' varying in thickness from a foot or two to several hundred feet. These consist for the most part of various types of felsite rocks, classed, by the sanction of common and long-continued usage, under the general term of porphyries. Mr. S. F. Emmons, in the abstract of his " Report upon the Geology and Mining Industry of Leadville," says in this connection : In their mode of occurrence the type-feature is that of intrusive masses, which are developed on a scale of unprecedented magnitude, and follow certain horizons with remarkable regularity.... It is probable that this mode of occurrence of eruptive rocks, viz., as intrusive masses which originally did not reach the surface but were forced up to a certain horizon and then spread out bettween the beds, is far more common than has hitherto been suspected by geologists. It is difficult to conceive of the conditions under which a fused mass could pry open strata to a width of one thousand feet or more, overcoming the weight often thousand feet of superincumbent rocks, and spread itself out in a continuous sheet between the beds to a distance of ten miles beyond the point or line of eruption. That they did exist, however, can be clearly demonstrated in this region.... In one single section over fifteen sheets, many several hundred feet thick, were counted between the Blue Limestone and the top of the Carboniferous. The region here under discussion is made up of a series of great

Jan 1, 1885

By John C. Smock

The rich deposits of magnetic iron-ore in the Highlands of northern New Jersey attracted the attention of iron-workers at the time of the earliest settlements in that region. The outcrops of the oreshoots at the Dickerson mine, at Mount Hope, and at Hibernia, in Morris county, and at Ringwood, in Passaic count,y, which were doubtless such as would lead to discovery, location and development of nearly all the large iron-mines in that part of the State, appear to have had their beginnings where the ore cropped out on the surface or where it was scarcely concealed by a thin mantle of earth. In the early history of New Jersey iron-mining, the careful explorations and surveys made by the agents of the famous London Com-

Jan 1, 1892

By H. N. Mead

In a reservoir when gas comes out of solution and rises, additional pressure is created because of the change in position of this gar in the bounded volume. If this pressure effect is not taken into account as a pseudo-influx ill mate rial balance calculations on reservoirs in which there is evolving gas, an error is introduced that is directly proportional to the length of oil column and amount of gas evolved and inversely proportional to the reservoir pressure. In reservoirs with small oil column this pseudo-influx is of little importance. The larger the oil column the more important the effect becomes. The most important application, however, will be for reservoirs with declining pressure in which increasing water entry has been indicated by material balance calculations. It could be that this indication is the result of the cited pseudo-influx and not water entry at all. This paper attempts to explain this phenomenon in relation to material balance calculations and prevents an approximate method of determining tile pseudo-influx. INTRODUCTION Only recently has the pressure-volume relationship of gas rising in a liquid appeared in engineering literature, although its effect has been discussed for several years—especially among engineers engaged in drilling operations. The writer published a paper in 1957 in which this phenomenon was examined in relation to blowouts in drilling wells.' Also, in 1957 Stegemeier and Matthews' authored a paper in which the relationship was presented with respect to pressure build-up tests when shutting in producing wells. In this paper the effect will be called "pressure inversion" which is descriptive of the phenomenon. Fundamentally, the effect just mentioned is the result of changing the position of a quantity of energy contained within the gas itself (as a result of its compression) within the bounded volume in which the gas exists. If the gas were allowed to expand "beyond all bounds" there could be no pressure inversion effect. This is because all of the energy contained within the gas as a result of compression would have been re- PRESSURE INVERSION A phase that has not been discussed in the literature is the effect of pressure inversion upon material balance calculations in reservoirs in which the reservoir pressure drops with reservoir withdrawal and is below the bubble point. This action releases solution gas which, after the critical gas saturation has been reached, will tend to rise and collect at the top of the reservoir. The pseudo-influx caused by this effect could be great enough in reservoirs of large oil column and high permeability to render invalid any analyzer studies made on them — if pressure inversion has not been taken into account. Most suspect would be those reservoirs with large oil column in which increasing water entry has been predicted but the bottom wells have not yet produced water. Example 1 Simply stated, this phenomenon exists in oil reservoirs because of the difference in density and expansibility between gas and oil. For example, if a bubble of gas exists at the bottom of a 1,000-ft column of oil having a gradient of 0.30 psi/ft with the pressure at the top of the column zero, the bubble of gas will be compressed to a pressure of 300 psi. If temperature and the combined volume of the oil column and the gas bubble remain constant, as the gas bubble rises in the oil column it will have the same volume and consequently the same pressure at any point. Under these conditions when thc bubble reaches the top of the oil column, the pressure will be approximately 300 psi at the surface and approximately 600 psi at the bottom of the oil column. If it is assumed that the oil is incompressible the pressures will be exactly 300 and 600 psi, respectively.

By L. D. Anderson

IN STUDYING Utah as a lead producing state one is immediately confronted by the fact that few, if any, of the ores of the state are valued for their lead contents alone. More correctly the ores from which this metal is recovered are characterized as silver lead. Even then the whole story is not told for many of these ores carry also gold, copper, zinc, bismuth, antimony, arsenic, tellurium, and other metals. It becomes apparent, therefore, that the production of lead i11 Utah is influenced by many factors. For example, i11 the early part of 1923 there was a marked increase in the production of the lead by reason of the efforts made by silver mines to produce as much silver as possible before the termination of purchases under the Pittinan Act in June, 1923. As nearly all silver ores carried more or less lead the production of that metal was increased with the increase in silver production. Very few, if any, ores of the State are mined for their lead contents alone. Important as Utah's contribution to the lead output of the country is nevertheless it is bound up to some extent with the production of gold, silver and copper.

Jan 1, 1925

By W. M. Bertholf

In 1945 tests were made in the coal washery of the Colorado Fuel and Iron Corporation, at Pueblo, Colo., to determine the value of the Humphreys spiral. So far we have demonstrated that it is of definite value to us in rewashing a portion of our table middlings; and we are fairly certain that this is not necessarily the only place in which it can be used to advantage. Because of manpower and material shortages, experimental work has been discontinued for the present. Three of the spirals are being installed for use in rewashing the middlings, and testing and experimental work will proceed when this installation is completed. All evidence secured so far points to the fact that the spiral call make an effective separation of heavy material below 8-mesh; but that it is ineffective in removing larger, heavy material. This, of course, will limit its use to fine coal or a classified feed containing no heavy material larger than 8-mesh. In considering the results of our tests, it should be noted that the feed was our table middling, and that any real separation of this material is a "moral victory)" as there is little material that could be properly called coal and practically no heavy rock, the consequence being that previous attempts to clean the middlings have not been at all successful. Several articles dealing with the spiral and its use in treating heavy minerals have already been published,' but for the benefit of those who have not seen these we include a brief description of the spiral and of the way it operates, taken from Bulletin 4 of The Humphreys Investment Co.: The Humphreys Spiral Concentrator consists of a spiral conduit of modified semicircular cross section. Ore pulp is fed to the top and, as it flows downward, the heavier particles concentrate in a band along the inner side of the pulp stream (Fig. I). Outlets for removal of products are located at the lowest points in the cross section of the conduit. Wash water, added at the inner edge of the stream, flows outwardly across the concentrate band. The width of concentrate band removed at the outlets is controlled by adjustable splitters. Concentrate is usually removed from the upper portion of the spiral and middling from the lower portion. Tailing is discharged from the lower end. Tests are usually made in closed circuit, since this provides a maximum of information with a minimum amount of sample. Fig. 2 shows the spiral set up for closed-circuit testing, and gives a good idea of the general arrangement of such an installation. The small cyclone separator is used to provide clean wash water without introducing additional water into the circuit.

Jan 1, 1947

By W. M. Bertholf

In 1945 tests were made in the coal washery of the Colorado Fuel and Iron Corporation, at Pueblo, Colo., to determine the value of the Humphreys spiral. So far we have demonstrated that it is of definite value to us in rewashing a portion of our table middlings; and we are fairly certain that this is not necessarily the only place in which it can be used to advantage. Because of manpower and material shortages, experimental work has been discontinued for the present. Three of the spirals are being installed for use in rewashing the middlings, and testing and experimental work will proceed when this installation is completed. All evidence secured so far points to the fact that the spiral call make an effective separation of heavy material below 8-mesh; but that it is ineffective in removing larger, heavy material. This, of course, will limit its use to fine coal or a classified feed containing no heavy material larger than 8-mesh. In considering the results of our tests, it should be noted that the feed was our table middling, and that any real separation of this material is a "moral victory)" as there is little material that could be properly called coal and practically no heavy rock, the consequence being that previous attempts to clean the middlings have not been at all successful. Several articles dealing with the spiral and its use in treating heavy minerals have already been published,' but for the benefit of those who have not seen these we include a brief description of the spiral and of the way it operates, taken from Bulletin 4 of The Humphreys Investment Co.: The Humphreys Spiral Concentrator consists of a spiral conduit of modified semicircular cross section. Ore pulp is fed to the top and, as it flows downward, the heavier particles concentrate in a band along the inner side of the pulp stream (Fig. I). Outlets for removal of products are located at the lowest points in the cross section of the conduit. Wash water, added at the inner edge of the stream, flows outwardly across the concentrate band. The width of concentrate band removed at the outlets is controlled by adjustable splitters. Concentrate is usually removed from the upper portion of the spiral and middling from the lower portion. Tailing is discharged from the lower end. Tests are usually made in closed circuit, since this provides a maximum of information with a minimum amount of sample. Fig. 2 shows the spiral set up for closed-circuit testing, and gives a good idea of the general arrangement of such an installation. The small cyclone separator is used to provide clean wash water without introducing additional water into the circuit.

Jan 1, 1947

By H. M. Woodroffe, H. K. Conn, S. J. Rice

World production of asbestos is estimated to be at a current level of almost 3.5 million tons, having more than doubled in the past ten years. A substantial part of the increase has been due to a rapid expansion in the Soviet Union. Production from that country during 1964 is estimated at 1.5 million tons and, as a consequence, Russia has displaced Canada as the leading world producer. Although traditionally the asbestos mining industry has been centered near Sverdlovsk in the Urals, two new producing areas have been under development for some time. It is expected that a new mine will be in operation in 1965 near Kiembi, Kazakhstan, some 300 miles south of Sverdlovsk, and an- other mine at Aktrovak in Tannu-Tuva, west of Lake Baikal. These developments will provide a significant increase in the production capability of Russia. Although internal consumption is expected to increase with the addition of new asbestos- cement producing facilities now under construction in Russia, there is some speculation that exports will also increase.

Jan 2, 1965

By J. P. Witherow

The blast-filmace plant of the Crozer Steel and Iron Company was built under contract by Witherow & Gordon, of Pittsburgh, Pa. The furnace is 70 feet high by 16 feet bosh, tunnel-head 12 feet 8 inches, and hearth 9 feet in diameter. The columns are 20 feet high above furnace level, below which they extend 2 feet. The shell is 23 feet diameter at bottom and 19 feet at top. The plate iron is 3/8 inch at bottom, and tapers to 1/4 inch, the top ring being 5/16 inch.

Jan 1, 1884

By G. A. Vissac

MOISTURE in coal must be considered as an impurity, just the same as ash, from the standpoint of utilization of the coal. Being incombustible, it reduces directly the heating value of the coal, and in addition absorbs heat for its evaporation. Its presence means useless expenditures in handling and transportation. In coke plants, extra moisture reduces capacity and may cause damage to brick work and equipment. Accordingly, the removal of extra moisture can be considered just as important as the removal of other impurities, such as ashes, in the modern coal preparation plant. Moisture, which can be removed by heating the coal up to a temperature of 100°C, may be retained in various forms: 1. As a film, on the surface of each coal particle, and in the interstices between particles, retained by capillary forces. 2. Or "occluded" inside the coal particles. This occluded moisture may be either free moisture (as in a sponge), or hygroscopic moisture which varies with atmospheric conditions, (also called "regain").

Jan 1, 1949

By B. I. Routh

A STUDY of the effects of temperature on the gel strength of drilling muds is a natural outgrowth of the present era of deep drilling. The control of the gel solids' is now considered important because it affects the wall-building qualities; the suspension of weighting material; the removal and release of sand, cuttings, and gas; and the control of cav-ing formations. With regard to the effect of temperature on gel strengths Herrick2 states: "Temperature variation within ordinary limits does not have much effect on yield points." Lewis, Squires and Thompson3 investi-gated one clay and found no marked change with temperature in either yield point or mobility. Reed4 found that potassium bentonite showed a great increase of gelation with increase in temperature and qualitatively there occurred a marked increase in viscosity upon heating. The apparatus used in these experiments consisted of a Stormer viscosimeter, Marsh funnel viscosimeter, rectangular and cylindrical shearometers, Mudwate hydrometer, and other minor laboratory equip-ment. The various methods of measuring viscosity and gel strength have been extensively described by Evans and Reid.5

Jan 1, 1938

By Jack F. Harang, P. B. Leavenworth

Development during the year 1941 on the Texas Gulf Coast resulted in the dis covery of 27 new fields as compared to 26 fields for the year 1940. Drilling.—During the year, 1405 wells were drilled. Of this number, 1031 were completed as oil wells with 375,000 bbl. daily of new production; 50 were com pleted as gas wells and 324 were failures. The most active area was Jackson County, where 375 wells were drilled and 336 of them accounting for 190,000 bbl. daily of new production. Types of Fields.—Of the 2 7 new fields, 14 are considered to be oil fields, 8 are listed as gas-distillate fields and 5 as gas fields. This may be compared to 26 fields found in 1940, of which 14 were oil fields and 12 gas-distillate fields. Producing Sections.—Frio discoveries retained their predominant position by having 10 Frio fields discovered in comparison to 6 fields in the Wilcox, 4 in the Yegua, 5 in the Miocene and 2 in the Jackson. In the previous year 15 Frio fields were found, 4 in the Wilcox, 2 each in the Yegua, Cook Mountain and Miocene, and I in the Jackson. Production.—Production increased over 1940 approximately 10 per cent, being 113,726,893 bbl. for the year 1941 and 104,127,247 bbl. for 1940. The statistics in Tables I and 2 include distillate and condensate as oil production because no separate reports have been compiled. It is hoped that this separation may be possible some day, but as a great many fields produce both oil and distillate and these arc commingled in pipe lines, separation of statistics will be more difficult than for other areas. New Fields Big Hill, Jefferson County.—Stanolind Oil and Gas Company's No. I George D. Anderson was completed as a gas well from a Frio sand at 8705 to 8720 ft., on Dec. 24, 1941, after having been drilled to a depth of 9500 ft. Additional development is being carried on but it is not possible to evaluate this discovery at this time. Brushy Creek Field, Lavaca County.— Shell Oil Corporation's No. I D. G. McManus was completed as the discovery well in the Brushy Creek field on Oct. 29, 1941, from a Wilcox sand through perforations at 7225 to 7230 ft., making gas and 180 bbl. of 59° gravity distillate. This well was bottomed at 10,998 ft. in the Wilcox. No statement can be made at this time as to the importance of this discovery. Chenango Field, Brazoria County.—J. N. Rayzor et al. completed their No. I Sarah J. Christian through perforations at 8564 to 8572 ft. in a Frio sand, for 453 bbl. of 37.7° gravity oil, on Feb. 6, 1941, after having drilled to 9564 ft. Several wells were drilled in this area during the year but failed to establish important production. This is considered a minor discovery. Clodine Field, Fort Bend County.—Providence Oil Company's No. I Hatfield was the discovery well of the Clodine field, being completed through perforations at 7499 to 7502 ft. for 108 bbl. of 51.2° gravity distillate, on June 19, 1941. The well was bottomed at 8090 ft. Several wells

Jan 1, 1942