Search Documents

OPEN-HEARTH refractories are not merely an accessory to the furnace. They are the furnace, to all intents and purposes. The steel work of the main structure is merely an open frame which helps to support the refractories ; and the regenerators, a necessary part of the furnace system, consist almost entirely of refractories. Not only do refractories constitute the essential part of the furnace, but they also carry the liquid steel all the way to the point where it begins to solidify. On leaving the furnace the liquid passes through a refractory runner into a refractory-lined ladle, then through a refractory nozzle closed by a refractory stopper on the end of a rod protected by refractory sleeve bricks. The liquid is sometimes sent through an additional refractory- lined tundish, a supplementary ladle, or a refractory runner for bottom pouring, until it finally enters the iron mold in which it solidifies. Even in the mold, refractory materials are sometimes used to provide a nonconducting "hot top." This series, from runner and ladle to hot top, inclusive, is often referred to collectively as the "pouring-pit refractories." REFRACTORY RAW MATERIALS The raw materials available are best classified into basic and acid types. The principal basic raw materials are magnesite, dolomite, and chrome ore. The principal acid materials are silica in various natural forms, and fireclay. Magnesite. Austria was the principal source of magnesite (MgCO3) until recent years, when the Province of Quebec, in Canada, and the states of Nevada and Washington became important sources for the American steel industry. More recently these natural sources have been supplemented by the so-called "sea-water magnesite"-which is the name somewhat incorrectly given to magnesium hydroxide obtained as one of the products

Jan 1, 1964

By R. C. Troxell, S. C. Sun

EFFORTS to obtain definite quantitative data when employing the currently used bubble pick-up method1,2 as a pre-flotation investigation tool led to the adoption of the magnifying mirror method and the microscopic method modifications. Quantitative data obtained by these two methods were converted into bubble pick-up indices and bubble pick-up coefficients. Rough correlations were established between the calculated indices and the results of contact angle testing as well as actual flotation under the same conditions. The basic steps of the magnifying mirror method are as follows: 1—mixing 200 ml distilled water, sized and cleaned mineral particles of approximately 0.5 g, pH regulator, and flotation reagents in a glass beaker; 2—swirling the mineral particles to the center of the beaker to leave a clear circumference; 3—pressing an air bubble against the mineral particles for about 1 sec, and then moving the mineralized air bubble to the clear part of the beaker; and 4—dropping all the attached mineral particles of the air bubble by tapping the bubble holder, and counting the number of the dropped particles by looking at the magnified image in the mirror positioned beneath the beaker. This method is impractical for mineral particles which are transparent in water or finer than 200 mesh. The microscopic method is essentially similar to the above described magnifying mirror method, with the exception that the mineralized air bubble was drawn up into the bubble holder and subsequently discharged onto an externally placed watch glass, where the number of pick-up particles was counted with the aid of a microscope or hand lens. Drying was necessary when the discharged liquid interfered with the counting. The results of the bubble pick-up tests can be simply expressed in the form of the actual count. However, this can be misleading because the number of pick-up particles varies not only with the size of bubble but also with the size of particles. This short-coming is largely remedied by the use of the bubble pick-up index. as calculated from the following equation: PI = (pn/p) 100 [1] in which PI and pn are respectively the pick-up index and the number of pick-up particles under any test conditions, and p is the maximum number of pick-up particles of the same mineral under optimum flotation conditions, with the same size holder and particle. The bubble pick-up coefficient is a term coined to denote the difference between the bubble pick-up index of mineral particles in a liquid and that of the same mineral-liquid mixture plus a chemical reagent at the same pH value. For example, the difference between the pick-up index of a naturally floatable bituminous coal in a solution of water and kerosene and that of the same coal in water alone is a bubble pick-up coefficient. Compared with the contact angle method, the quantitative bubble pick-up method is inferior in accuracy but superior in sensitivity. Other advantages of the bubble pick-up method are that the apparatus can be easily assembled, the mineral sample is conventionally prepared, and the test procedure is relatively simple. References S. R. B. Cooke: The Flotation of Quartz Using Calcium Ion As Activator, Trans. AIME (1949) 184, p. 306. 'G. A. Last and M. A. Cook: Theory of Collector-Depressant Equilibrium at Mineral Surfaces. Paper presented at St. Louis Meeting, AIME (February, 1951).

Jan 1, 1954

By S. J. CRAIGHEAD

IN 1912 the United States Smelting Refining and Mining Company made a large investment in a number of coal properties in Utah and in 1915 a subsidiary, the United States Fuel Co., was organized to take over these properties. Operations started in 1916 and the Company soon became, and remains, one of the major coal producers of the State. It now produces approximately one million tons of coal annually, which is about 22 per cent of Utah's output. The U. S. Fuel Co. owns large reserves of good coal and is in a position to expand operations with the industrial growth now taking place in the West. Traveling through the Western States, one is struck by numerous advertising signs portraying the picture of jovial Old King Cole of nursery rhyme fame. His rotund figure and beaming countenance are the symbols of Utah King Coal, the product of the King mine of U. S. Fuel Co. King Coal is a by-word of quality coal throughout all the Western States.

Jan 1, 1948

By T. H. Aldrich

(San Francisco Meeting, October, 1911.) THERE are two conditions generally prevailing upon the earth-those within atmospheric influence, tending towards oxidation, and those away from atmospheric influence, tending towards reduction. Practically all mineral substances from mines of any depth are in a reducing condition. Since the cyanide process, in order to dissolve silver or gold, requires that the prevailing conditions under which it operates shall be oxidizing, and the materials usually acted upon being of a reducing character, it becomes necessary to supply oxygen to the solution carrying the cyanide. This oxygen is usually supplied through the medium of dissolved air in the solution, or through the medium of various chemical compounds, which upon combining with the solution or the ore give off a part of their oxygen. Strange as it may seem, practically all mineral substances are partly soluble in water, especially water carrying alkali or cyanide. The greater the surface exposed and the finer the material is ground, the greater will be the rate of dissolving of the reducing agents from the ore into the cyanide solution. In most cases, if the solution carrying the ore particles is agitated with air, the air will dissolve into the solution faster than will the reducing-agents; but in some cases the reducing-agents will dissolve more rapidly on account of easy solubility or greater surface exposed. It is a dissolving race between the oxygen from the air and the reducing-agents from the ore, and if the reducing-agents predominate, cyanide will not dissolve the gold from the ore. In many cases it will dissolve some of the gold, because in a mass of irregular shape some of the gold particles might be exposed upon the outside surface of a particle of rock;' but if the solution had to penetrate through cracks, the side-walls of which were lined with reducing-agent-

Feb 1, 1912

By Fleming, R. C.

ONE OF THE NEWEST developments of industry rising from the commercial application of scientific knowledge is in the making of solid carbon dioxide from the gas about 1925 the first efforts were made to manufacture "dry ice" on a large scale and at a price to permit widespread use. From that beginning the industry has grown to a consumption of 40,000 tons in 1930. Carbon-dioxide ice, as the name implies, is merely the gas compressed and cooled to a solid. The ice has a temperature of 109° F. below zero and is in many ways superior to water ice. It evaporates to a gaseous form so it is not wet and leaves no trace; in fact, one suggested minor use is as coasters under water glasses on the dining table. The gas is harmless except in large concentrations and. when the ice is used as a refrigerant, the resulting gas actually becomes a preservative, keeping oxygen away from perishable products. Not only does the ice have a greater amount of cold in a small volume than water ice but cooling is effected by direct contact of the resulting gas with the materials to be refrigerated rather than by convection air currents.

Jan 1, 1932

The elite group of companies below represent the mining sector of Fortune magazine's June Directory listing the 500 U.S. industries that chalked up the largest dollar sales volume in 1966. The companies are listed according to their 1966 sales rank, which is given along with their 1965 rank for comparative purposes. All of the firms except two-Freeport Sulphur and Texas Gulf Sulphur-were in the Fortune Directory last year, and both these exceptions have been counted among the top 500 in former years. The one mining name that is missing from last year's list-Consolidation Coal-has actually jumped from number 217 to 4 by virtue of its merger with Continental Oil. As can be seen from the Industry Medians, the mining industry as a whole boosted its sales 17.8%, in 1966, making it the seventh largest gainer among the 22 industrial classifications covered in the Directory. By comparison, 1965 mining sales increased 10.2%, a gain which was surpassed by 13 other industries. In two other comparative tables, mining leads the field, topping the entire list in return on sales and in assets per employee.

Jan 8, 1967

By Robert Laurich

Chuquicamata pit was opened in 1915 with steam shovels and steam locomotives brought down from the Panama Canal excavation project. With expansions in the early years, more steam locomo¬tives were brought into the mine. IMPROVED LOCOMOTIVES During the period 1927 to 1937, electric locomo¬tives were purchased and main line and bench tracks were electrified. Third rail was installed up to the working areas. At first, the locomotives were equipped with batteries for service at the shovels, but charge life was too short and they were con¬verted to use the third rail and a reel with 3000 ft of trailing cable for service in the loading area.

Jan 11, 1959

By J. D. A. Morrow

TO my mind the National Bituminous Coal Act so far has proved one of the unhappiest experiences that has ever befallen the bituminous coal operators of the United States. Viewed in the light of its ugly consequences everyone should recognize this measure for what it is -a weird thing as unreal as a page from "Alice in Wonderland." Indeed it might be another stanza to the tale of the Walrus and the Carpenter, with the coal operators in the role of the unfortunate oysters who were taken on that memorable ramble. It is time that coal producers open their eyes, jerk themselves out of any lingering hypnotic optimism about the price-fixing provisions of this law, demand the repeal of these corroding clauses, and then set about remedying as best they can the disastrous effects of this retromingent scheme to regulate the coal business.

Jan 1, 1939

The oil production in Bahrein for the year 1937 was 7,762,264 bbl., a monthly average of 646,855 barrels. Sufficient potential production had been developed in the Second Pay (Main Pay) at Bahrein by the end of 1936 to supply the anticipated crude demand, and the drilling program was changed from straight development to partial exploration during 1937. Two nonproductive wells were drilled to test the Third Pay at a depth of about 2900 ft., or some 900 ft. below the top of Second Pay. As a result of this exploratory work, the normal drilling program was slowed down and only eight new wells were completed in the Second Pay during 1937, making a total of 45 producers from the Second Pay. The deep test was drilling at 5081 ft. at the end of the year. A 550-ft. section (termed Fourth Pay) of porous limestone interbedded with anhydrite was topped at about 4150 ft. Numerous drill-stem tests indicated that the limestone was very permeable and that it carried large volumes of natural gas under high pressure together with a small amount of high-gravity oil or condensate. Drill-stem tests also indicated that the bottom 50 ft. of the 550-ft. section carried an encouraging amount of heavier oil, gravity about 37" A.P.I., with characteristics similar to the oil produced from the Second Pay. A well was started somewhat down-structure from the deep test to better determine the oil-producing possibilities of the Fourth Pay. Some refinements in drilling technique were adopted during the year. All wells started to the Second Pay were drilled with rotary from the surface. The top 1500 ft. of porous limestone section, formerly drilled with cable tools, is now drilled with rotary without circulation, using water to wash the cuttings into cavities. The shale section from this point to the top of the oil horizons is drilled with natural mud circulation. The productive horizons are drilled with oil circulation under pressure control. A second satisfactory method of completing wells was developed when the two Third Pay test wells were plugged back and gun-perforated through cemented casing opposite the Second Pay, with good results.

Jan 1, 1938

By F. H. Ellinger

TI HE crystal structure of neodymium has been re-A ported by Quill1 and by Klemm and Bommer"s to be hexagonal-close-packed, Strukturbericht-type A3, with a, = 3.650.4, c, = 5.890.4, c/a = 1.614. Klemm and Bommer,% owever, pointed out that the observed intensities of the lines of the neodymium powder pattern agreed only in part with the intensities calculated for the type A3 structure, and that the neodymium powder pattern showed extra lines which could not be traced to impurities. They found that these extra lines could be accounted for by doubling the c-axis, but apparently they did not consider their evidence to be sufficiently conclusive to justify reporting the doubled c-axis. In the present work, the structure of neodymium was found to be double hexagonal-close-packed. The neodymium metal used in the present investigation was obtained through the courtesy of F. H. Spedding of the Ames Laboratory. Its major impurity was stated to be 0.03 pct Ca. The author's spectrographic analysis indicated high purity and carbon was determined to be less than 30 ppm. X-ray powder specimens were prepared from filings stress relieved in vacuum at 200°C for 50 hr. Powder photographs were taken in an 114.6 mm diam camera (Straumanis film mounting) at room temperature and in a 19 cm diam Unicam high temperature camera at elevated temperatures. Copper x-radia-tion was used for all the photographs. The powder pattern of neodymium was found to index to a hexagonal unit cell with dimensions, as determined from the high angle Ka doublets, of: a.= 3.655+0.001.4; c, = 11.796+0.004.4; and c/a = 3.227 at room temperature. The measured density of neodymium shows that this cell contains 4 atoms, the calculated density is accordingly D, = 7.02 g per cu cm. The diffraction data for the first 15 lines of the powder pattern are listed in Table I. In a double hexagonal-close-packed unit cell, the 4 atoms would be in the positions (0,0,0), (0,0,%), (1/3, 2/3, 1/4), and (2/3,1/3,%) of space group P 6,/mmc. On the basis of these positions, the relative intensities of the reflections were calculated using the expression: 1+cos2 20 I oc \Frp 1 ' sin2 0 cos 0 where F is the structure factor and p is the multi- plicity factor. Since absorption was not taken into consideration, comparison of observed and calculated intensities should be made only for neighboring reflections. Each atom has 12 neighbors, 6 in the basal plane at a distance of 3.655.4 and 3 above and 3 below at the closer distance of 3.626.4. These distances correspond to an average radius of the neodymium atom of 1.820.4. The description of this structure in terms of A, B, and C close-packed layers of atoms is ABAC ABAC. ...... The structure repeats every fourth layer and the stacking sequence of the second, third, and fourth layers corresponds to cubic-close-packing of atoms. A series of powder photographs taken at successively increasing temperatures up to 680a10"C revealed that the double hexagonal-close-packed structure is stable up to this temperature. Acknowledgments The authw wishes to thank W. H. Zachariasen and A. S. Coffinberry for their helpful comments on this work and also Marion Gibbs for measuring the diffraction films. This work was sponsored by the United States Atomic Energy Commission.

Jan 1, 1956

By Alan Kissock

MOLYBDENUM is thought of as one of the rarer elements, for though it occurs in almost every country of the world it is seldom found in commercial quantities. In this country, however, there is one deposit which makes the term "rare" a misnomer. There are two commercially mined molybdenum minerals: molybdenite, the sulfide, and wulfenite, a lead molybdate. Of these two only the former is of any con- sequence but wulfenite is of mineralogical interest. It is frequently associated with oxidized lead ores and particularly in arid sections. Deposits, however, are usually quite superficial. It is highly oxidized and yet it does not appear to be an alteration product for it apparently disappears below water level and I know of no case where primary molybdenite, or in fact any molybdenum whatever has been identified below these surface wulfenite occurrences. The genesis of wulfenite would make an !- interesting study.

Jan 1, 1933

By Richard J. Robbins

Mechanical moles have developed through a tedious process of evolution. At times it has seemed that tunnel borers have been subject to the same Darwinian rules of evolution as their zoological namesakes who, despite their efficiency, are highly specialized and still restricted to soft soil conditions near the surface of the ground. HISTORICAL HIGHLIGHTS The Robbins Co. began its work in this field in 1947 with the development of a twin-bore continuous coal miner. Although these machines were used primarily in coal, two of the early prototypes were used to bore tunnels through shale. Disk cutters were first used on these machines and showed promising results as core breakers between drag-bit kerfs. In 1953, James S. Robbins and Assocs. undertook the development of a 25-ft 9-in.-diam circular tunnel borer for Mittry Construction Co. to be used at Oahe Dam in South Dakota (Fig. 1). This is believed to be the first rock tunnel-boring machine built since the end of the 19th century when short sections of the Channel tunnel were successfully bored in chalk from both the English and French shores. Another Oahe Dam machine was built in 1955, and then a series of three small-diameter machines for the company's first real experience with medium-hard and hard rock (Fig. 2) None of these three could be considered a success, although they laid the groundwork for the success that followed. Interbedded shale and limestone in Pittsburgh and hard limestone in Chicago quickly pointed up the weaknesses in these machines which were used by Perini, Dravo, and Healey. Among the problems were the high breakage rate of tungsten-carbide drag bits, too much flexibility in the drive shafts, failure of high-pressure hydraulic systems, chain-conveyor failure, and general lack of rigidity and strength. In 1956 another attempt at medium-hard and hard rock-boring proved this time to be a success and a significant turning point in the development

Jan 1, 1970

By AIME AIME

CERTAINLY in point of attendance, and doubtless in several other ways as well, the 147th meeting of the A.I.M.E. was the best ever held. In times of depression, mining engineers and metallurgists have plenty of time to come to the Annual Meeting but money is scarce; at the height of industrial activity they have plenty of money but no time. "The current period of transition seemed to provide ideal conditions for' both the preparation of papers and attendance at their presentation. The weather made even the Californians present envious though the weather man gets no credit, for rain and snow was what he willed. Among the elevator men, the miners have the reputation of being the toughest crowd to handle, though the best natured, withal, of all the engineering groups that meet in the Engineering Societies Building. This year Your inquiring reporter was told, "it was the damnedest meeting I ever saw; they

Jan 1, 1937

By J. T. Ryan

POISONOUS, irritating, or explosive gases are found in almost every industry, and manufacturers of gas masks are called upon to provide gas mask protection for a great variety of conditions, such as operators in horseradish factories, fumigators of homes and ocean liners, and men engaged in the manufacture of tetra-ethyl-lead, the new motor fuel. The modern type of gas mask and respirator, to provide protection against all such industrial gases, is an outgrowth of the gas mask developed during the World War to protect the soldiers against the poisonous war gases. So far, it has been possible to develop ample mask protection from all known noxious gases and fumes present in atmospheres encountered in mines, metallurgical works, and chemical and other industries, so long as there is sufficient oxygen present to support the flame of an oil lamp. The most important development of the gas mask was in providing protection against carbon monoxide- which is the noxious gas that mining men are most concerned with and, in fact, is the noxious gas that man is most frequently exposed to. This paper will be con- fined largely to the discussion of masks for underground use in metal mines. Gases that contaminate the normal air in mines can be divided into two classes: those that are given off normally by the workings, and those that are produced in mine operation.

Jan 1, 1926

By Mi Chung

T HE ore-dressing problem at Tul Mi Chung is complicated by the unusually complex nature of the ores. These come from replacement ore- bodies in limestone at the contact with a granite batholith, and contain copper, gold, silver, bismuth, molybdenum, iron, arsenic, zinc, and lead, the first two metals constituting the principal sources of profit. Iron is present as pyrite, magnetite, and hematite. Arsenic occurs both as mispickel and lollingite (FelAsa), the latter carrying a certain amount of finely divided gold. The gangue minerals are those typical of limestone con- tact-metamorphism and include a large percentage of garnet, together with diopside, serpentine, calcite, epidote, zoisite, actinolite, 'mica and other minerals. A part of the gold occurs in a free state; some is combined with chalcopyrite and lollingite, and a consider- able proportion is contained in the pyrite. Researches towards the improvement of recovery have been energetically conducted since 1915. Amalgamation, gravity concentrating tables, vanners, can- vas plants, etc., have all been tried and discarded in favor of flotation. It was very quickly established that fine grinding was essential for satisfactory recovery. This was and is still accomplished in Hardinge ball and pebble mills. A comparative test showed that when the ore was crushed to the point at which it contained 20 to 26 per cent. coarser than 100 mesh, the gold recovery was only 55.9 per cent., whereas when crushed so that only 11 to 15 per cent. was coarser than 100 mesh, the gold recovery was increased to 82.5 per cent. No particular difficulty was ever experienced in making a satisfactory recovery of copper but the losses in gold were considered serious and led to the investigation described in this paper.

Jan 1, 1924

By Steven Mitchell

BACKGROUND Homestake Mining Company began milling operations at the Bulldog Mountain Mine near Creede, Colorado in 1969. The Bulldog Mill, rated at 350 tpd, produces a bulk flotation condentrate assaying about 180 oz/T Ag and 20% Pb, from heads of about 16 oz/T Ag and 2% Pb. The circuit is straightforward with two-stage grinding to 1-5% plus 65 mesh, followed by rougher and cleaner flotation. Reagents used are Z-6, Z-11, Aerofloat 242 and Aero Promoter 404, with an Aerofroth 65-MIBC mixture for a frother. Additional information on the geology, mine and mill are available in references (1) and (2). A flow sheet for the mill and CIP plant together is attached as Figure 1. Final flotation tailings normally vary from 1.5 - 2.0 oz/T Ag. These tailings are cycloned to produce sand for underground backfill. After cycloning, the sands are repulped and given a final scavenger float. This sand scavenger recovers a small additional amount of silver which recycles back to the main flotation circuit. The tailings are recycloned and pumped to the mine or, if the mine cannot accept sand, to tailings. The majority of the silver in the flotation tailings exists in the fine fractions; cycloning upgrades the slimes and lowers the assay of the sand. The sand, after scavenging, typically assays 0.5 oz/T Ag, and the slimes assay about 3.0-3.5 oz/T Ag. From 1969 to 1976 all of the slime tailings and the sand tailings not used underground were impounded in a tailings pond located about

Jan 1, 1983

By E. D. Hummer

During the planning of the fine coal cleaning addition at the Gary, W. Va., Coal Preparation Plant of United States Steel Corp. careful consideration was directed toward the problem of minus 48 mesh refuse disposal. The plant flow sheet included wet screening the raw coal at ¼ in., pumping the minus ¼ in. raw coal to bowl desiltors for desliming, and then cleaning the deslimed raw coal on tables. The material to be removed from the circuit as minus 48 mesh refuse consisted of the minus 100 mesh desiltor overflow thickened in two 120 ft diam thickeners and minus 1 mm screened from the table refuse. Later a flotation plant was added to recover coal from the desiltor overflow, and a classifier replaced the screens to make a sharper size separation of the table refuse at 48 mesh. Today the minus 48 mesh refuse at Gary consists of thickened flotation tailing and thickened spiral classifier overflow. The transportation of large quantities of fine, wet refuse filter cake mixed with jig and table refuse over existing conveying equipment would have been neither dependable nor economical. Filtration was therefore impractical, and disposal of the fine materials was a problem. The decision was to pump the material to storage ponds.

Jan 3, 1965

By Desio S. Oddone, Mark C. Malamphy, Irnack C. Do Amaral

Most igneous rocks, and particularly those of the basic type, contain relatively high percentages of magnetite and other iron oxides, which give them moderately high magnetic susceptibilities and make them responsible for an important percentage of the magnetic anomalies observed during the course of geophysical surveys by the magnetic method. The irregular form and high susceptibility of the igneous rocks make them readily polarizable and the position and strength of the magnetic poles formed are not always explicable by theoretical calculations of anomalies due to certain assumed forms in the normal magnetic field of the area under study. During the last four years our field work has permitted us to make detailed observations of anomalies due to igneous rocks in all the states of south Brazil. The form and position of the igneous rock at some places were fairly accurately known, which made it possible to calculate theoretical anomalies and compare them with the observed data. Some of the data we obtained have been published and additional cases are now awaiting publication. In this paper, we will present a few specific cases where the geology is moderately well known and which we believe to be of considerable value as representing typical magnetic anomalies in the south magnetic hemisphere, where the inclination of the magnetic field is very low. Although the vertical intensity is negative in the Southern Hemisphere, we have adopted the convention of plotting increase in intensity (negative) as a positive anomaly; i.e., above the x axis. This convention facilitates comparison with anomalies in the north.

Jan 1, 1940

By Irnack C. Do Amaral, Mark C. Malamphy, Desio S. Oddone

Most igneous rocks, and particularly those of the basic type, contain relatively high percentages of magnetite and other iron oxides, which give them moderately high magnetic susceptibilities and make them responsible for an important percentage of the magnetic anomalies observed during the course of geophysical surveys by the magnetic method. The irregular form and high susceptibility of the igneous rocks make them readily polarizable and the position and strength of the magnetic poles formed are not always explicable by theoretical calculations of anomalies due to certain assumed forms in the normal magnetic field of the area under study. During the last four years our field work has permitted us to make detailed observations of anomalies due to igneous rocks in all the states of south Brazil. The form and position of the igneous rock at some places were fairly accurately known, which made it possible to calculate theoretical anomalies and compare them with the observed data. Some of the data we obtained have been published and additional cases are now awaiting publication. In this paper, we will present a few specific cases where the geology is moderately well known and which we believe to be of considerable value as representing typical magnetic anomalies in the south magnetic hemisphere, where the inclination of the magnetic field is very low. Although the vertical intensity is negative in the Southern Hemisphere, we have adopted the convention of plotting increase in intensity (negative) as a positive anomaly; i.e., above the x axis. This convention facilitates comparison with anomalies in the north.

Jan 1, 1940

By Ralph H. Sweetser

AT the end of 1943 the charcoal pig iron capacity of the United States was at the lowest point in over 1110 years, with only one strictly charcoal blast furnace in operation, and all others permanently out of blast except one in Tennessee d reported to he running on part charcoal and part coke. Such a decrease in production has taken place in spite of the O.P A.'s high-premium price on charcoal pig iron of +34 per ton f.o.b. furnace in Michigan. Depletion of the hardwood supply within fifty mlles or inure of the blast furnace is the reason why; the deplorable lack of reforesting is the cause.

Jan 1, 1944