Search Documents

ALTHOUGH it has been a matter of about one hundred years since the idea of the internal-combustion engine entered the mind of the inventor, the practical application of its use was not attained till 1860, when Lenoir produced an engine similar to the ordinary highpressure steam engine, with the valves arranged to admit the explosive mixture and the discharge of the exhaust gases. In this case no attempt was made to compress the gas before ignition, as it was then considered that the explosion under these conditions had a detrimental effect, inasmuch as it would act as a sudden blow to the working parts. Indeed, he went so far as to inject steam and water sprays to reduce the explosion.Under these conditions the consumption of gas was exceedingly high-about 106 cub. ft. of coal gas per b.h.p. per hour but the mechanical effect showed that the engine ran in every respect as smoothly and quietly as in best steam-engine practice.The extravagant consumption of this engine was clearly pointed out at the time by Gustav Schmidt in a paper before the German Society of Engineers, wherein he states :-" The results would be far more favourable if compression pumps, worked from the engine, compressed the cold air and cold gas to three atmospheres before entrance into the cylinder. By this means a greater expansion and transformation of heat is possible."

Jan 1, 1912

By C. G. Dunn, P. K. Koh

The primary recrystallization textures of 11 single crystals cold rolled 70 pct were determined. The effect of crystal orientation on recrystallization behavior was investigated also and found to be large. An exception was found to the relationship that strong components of the recrystolliza-tion texture are rotated from the cold rolled texture by 30° about <110> axes, but generally this relationship was found to hold quite well. Evidence supporting oriented nucleotion was found and discussed in terms of probable active slip systems and <110> edge dislocations. THE present paper is one of a series&apos;.&apos; on recrys-tallization phenomena in cold rolled 31/4 Si-Fe single crystals and is mainly concerned with the textures produced on recrystallizing from stable end orientations. Data for the cold rolled textures of the crystals used have been reported by Koh and Dunn." Their results showed that the sharpness of the cold rolled textures varied throughout the range of stable end orientations and that the tendency to re-crystallize was related to the sharpness of the cold rolled texture, wherein the rate of recrystallization increased and the size of recrystallization grains decreased with decreasing sharpness of the cold rolled texture. In the project under consideration the cold rolled crystals involved a range of initial orientations that, together with those studied earlier,&apos; provide information on several points. The first point is whether the recrystallization texture from a (111) [112] cold rolled texture, a stable end orientation that can be approached from different directions, correlates in any way with the initial orientation before cold rolling, or whether the recrystallization texture is entirely determined by the observable features of the cold rolled texture. The second point involves a preliminary study to see if the main components of the recrystallization textures correlate with the most probable active slip systems. The third point is to determine what effect departure from slip on one slip system has on the tendency to recrystallize. Experimental Procedure Nine specimens from a previous investigation and two additional ones from thicker stock (lot D) but of similar composition to the others were used in the present work. The latter two crystals, like the nine, were cold rolled to a reduction in thickness of 70 pct and the amount of widening was determined. Depending on their primary recrystallization behavior, the cold rolled crystals were given short or long anneals at temperatures of 980°C or higher. Table I summarizes the data on initial orientations, the textures obtained by cold rolling, and the anneals given to provide samples for the present work. Fine grained specimens were thinned to 0.002 in. thickness and placed in an integrating specimen holder. Chart recordings using a transmission X-ray method and MoKa radiation were obtained for diffraction from (110) planes. This method,&apos;,3 which gives data for all of the pole figure except a central region of 30" radius, proved sufficient to give generally five, and sometimes six, of the six possible pole concentration areas of any one component of the texture. These data, therefore, were generally adequate for a positive identification of each component present. The first texture obtained for specimen B-2 was poorly defined because of too coarse a grain structure and therefore too few crystals in each component for satisfactory X-ray reflections. The same

Jan 1, 1957

Law of the Sea. - The Ninth Session of the Law of the Sea Conference resumed July 28 at Geneva and will run for 5 weeks. The 160-nation Conference began in 1973. Two of the major factors to be discussed are the transfer of technology to the UN-controlled Enterprise or mining authority, and how the 36-member Council will make decisions. As the session completed its third week, delegates expressed little hope of completing a treaty text this year. There was a feeling, though, that substantive issues might be settled so that a treaty text can be completed next year. The Deep Seabed Hard Mineral Resources Act signed by the President on June 28, provides an interim regulatory procedure for ocean mining activities conducted by U.S. nationals that may be superseded by a law of the sea treaty.

Jan 1, 1980

By H Aral

A rotating magnetic field can be produced in a magnetic separator by using a magnet rotor fitted with alternate north-south magnetic poles, similar to the rotors currently used in modern eddy current separators. Rotation of the magnetic field causes ferromagnetic particles to rotate during magnetic separation. The particle rotation can then be used simply to remove entrapment during a conventional attraction magnetic separation (RMF lift separation), or it can be used to roll particles away from non-rotating particles, and to move them out of the separator under their own rotation (RMF rotation separation). RMF (rotating magnetic field) separation is a separation for ferromagnetic particles. These particles have a very ordered magnetism that is locked into directions of easy magnetisation in the crystal. As a result, if the external field rotates, the particles attempt to rotate with it. RMF separation uses this fact to rotate the ferromagnetic particles in a rotating field. In contrast, paramagnetic particles have a magnetism that can point in any direction with almost equal ease, and these will not rotate in a rotating field. By making use of this difference in magnetic properties, RMF rotation separation can separate ferromagnetic particles from paramagnetic, even when the particles have similar susceptibilities. Some particles such as both chrome spinel and ilmenite can contain ferromagnetic regions within a paramagnetic matrix. These ferromagnetic regions can vary from very small regions dispersed throughout the crystal, through thin lamellae, to larger more bulky regions. Although most natural ilmenite is ferromagnetic and generally has a higher magnetic susceptibility than paramagnetic chrome spinel, the susceptibility ranges for the two minerals overlap considerably (Allen, 2000a) due to the presence of these ferromagnetic elements, frequently making the conventional magnetic separation of these two minerals impractical. It is known that roasting a mixture of ilmenite and chrome spinel particles increases the magnetic susceptibility of the ilmenite while leaving the spinel susceptibility substantially unchanged. This makes the use of conventional (susceptibility attraction) magnetic separation more practical for the separation of these two minerals. However, very little is known about the effects of roasting on the response of ilmenite and spinel particles to a rotating magnetic field. For example, although the optimal ilmenite roasting conditions for conventional magnetic separation are quite well established such conditions may or may not be optimal for RMF rotation separation. Low intensity conventional magnetic separation on the basis of magnetic susceptibility can be made more accurate if it is carried out in a rotating field, because the rapid spinning of the separating particles prevents the formation of magnetic flocs, and reduces entrapment and entrainment. Medium intensity RMF rotation-only separation (no attraction component) has the ability to separate rotating (ferromagnetic) from non-rotating (paramagnetic) particles, irrespective of their relative magnetic susceptibilities. RMF rotation separation is of particular interest in this case because ilmenite particles generally rotate much better than the mainly paramagnetic chrome spinel particles, and roasting could enhance this difference further. Further information on the use of RMF to separate minerals can be found in Allen (2000a; b and c). The aim of this series of tests on a number of Australian ilmenites was to compare some different oxidising and reducing roast methods and to establish whether the use of RMF rotation separation improves the chrome spinel rejection.

Jan 1, 2001

By Wolfgang Van Hooff

Encouraged by a strongly growing and evolving market for granulated products, Paul Wurth continuously improves its granulation and dewatering technologies to provide customers with state of the art installations. Continuously developed know-how about the granulation process of iron blast furnace slag enabled application to non-ferrous materials such as Ni-Slag, Pb-Slag, Blister Copper, Cu-Matte and even TiO2-Slag, which rank among the most difficult materials to granulate. This paper identifies how critical objectives in granulation and dewatering technologies applied to different molten materials with respect to various product quality objectives can be addressed. The differences between hot and cold water granulation systems are explained, including the step from cold runner to granulation water tank. Development of a flow and pressure controlled blowing box is the latest step to optimize the granulation process in order to meet the latest standards in terms of quality, power consumption and environmental protection.

Jan 1, 2006

Since the 1989 Loma Prieta Earthquake in the San Francisco Bay Area, the California Department of Transportation (CALTRANS) has accelerated seismic upgrading of their bridges. Many structures can be improved with the simple addition of hinge seat restrainers. Others require modification of column bents and superstructure to column connections. Often, footing retrofits are necessary, which require the addition of tension/compression elements (compression piling and tiedowns anchors) to resist overturning moments substantially larger than those originally used for footing design. These footing retrofits may include doweled reinforced concrete footing extensions or new pile caps which transmit forces to either driven steel or drilled concrete piles. In some cases, installation of these traditional piling elements is expensive, impractical or impossible due to: low overhead clearance, ground obstructions, high water table, noise or vibration sensitivity, or the inability to laterally expand the existing plan dimensions of the footing. In the latter case, one practical option is to attach small diameter drilled and grouted tension/compression piling elements (Pin Piles) to the existing footing. The footing may be strengthened with dowels and added concrete thickness or there may be a reduced shear span due to the installation of larger or jacketed columns. A reduction of elements is available with a Pin Pile alternative, particularly when the selection of traditional standard piles is governed by the reduced tension/uplift capacity available from the traditional elements, since Pin Piles exhibit superior uplift performance.

Jan 1, 1993

By Jean Habimana

The Detroit Upper Rouge Tunnel CSO Control Project will capture and store up to 201 MG of combined sewer overflow from 28 outfalls in Detroit, Dearborn Heights and Redford Township during wet-weather events. The history of rock tunneling in the area is associated with high groundwater inflows, artesian pressure, and hazardous and combustible gases. This paper presents the geotechnical considerations for designing the 11.28-km (7-mile) long, 9.14 m (30-ft) finished diameter tunnel and its associated adits, chambers and shafts, including the discussions of geotechnical investigations, rock mass characterization, estimated groundwater infiltration during construction, and the selections of excavation methods and lining system based on anticipated ground behavior to be encountered.

Jan 1, 2008

By Syd S. Peng

Introduction The most commonly used ground control design in coal mining is the determination of pillar size by various pillar strength formulae for mine layout (Bieniawski, 1983; Holland, 1973; Hustrulid, 1976; Obert and Duvall 1967; Wilson and Ashwin, 1972). However, there have been few documented case histories concerning the validity of those strength formulae. Recently there are indications that those strength formulae tend to overdesign considerably. From a safety point of view, there is nothing wrong with overdesign. But an overdesign with large chain pillars reduces the flexibility of machine movement and decreases production. It also reduces coal recovery and, thus, shortens the reserve&apos;s life. This is especially true for small operators who own a limited reserve. Those small mines, through past practices or out of necessity, experiment with smaller pillars than those predicted by the strength formulae. Conclusive ev¬idence has been collected that points to the need of a new concept of coal pillar design. Two case studies will be cited to illustrate this point. 3-D US pillar strength formulae Figure 1 shows a sectional layout of a one-unit mine. The seam was about 1.3 m (50 in.) thick with a uniform cover of 64 m (210 ft). A house was located near the center of the section. The homeowner demanded that no surface subsidence and domestic well dewatering should ever be allowed as a result of underground room-and-pillar mining. Physical properties - strength and Young&apos;s modulus - of the rock strata including coal were obtained by testing small samples in the laboratory. The uniaxial compressive strength of the coal was 3660 kPa (823 psi). Using various pillar strength formulae, the homeowner recommended that square chain pillars be at least 11 m (35 ft) wide. The coal company, however, desired to pursue optimum coal recovery in the safest and most economical manner. They engaged in three-dimensional finite element analysis of the section taking into account the complete stratigraphic sequence of the overburden. Results indicated that the section can be developed by 5.5 m (18 ft) wide entries at 21 m (70 ft) center-to-center. In retreat, the pillars can be splitted along both centerlines leaving a stump pillar of 5.5 m (18 ft) square at each of the four corners. The 5.5 m (18 ft) square stump pillars still maintained a safety factor of 1.5, although the safety factors calculated by various pillar strength

Jan 11, 1986

By Wen Tao Liu, Tong Tian, Fu Sheng Niu, Xiu Man Liang

In order to address the difficulty of accurate segmentation of froth images of different sizes, a method of froth image segmentation based on highlight correction and parameter adaptation is proposed. First, a machine vision system on a single-cell flotation machine is built to collect froth images. Homomorphic filtering is used to improve the uneven brightness and shadow of the images. Fuzzy c-means (FCM) clustering is then utilized to classify similar highlights that belong to the same froth. After Otsu threshold segmentation, a parameter-adaptive morphological operation is used to extract the marker points and edge bands and correct the froth edges in the original image. Finally, the modified image is filtered by morphological reconstruction, and the highlight mark is used as the local minimum point for watershed segmentation. Three sizes of froth images are segmented in comparative experiments. The results show that the proposed method is suitable for the segmentation of froth images of different sizes. The position of the extracted segmentation line is close to reality, with average over-segmentation and under-segmentation rates for froth images of 2.6% and 6.8%, respectively. The froth image segmentation performance is stronger than that of the other methods examined.

By G J. Lyman

In sampling a process stream, conventional sampling theory deals only with the variation of the analyte content and neglects the impact of the variation in the mass flow on the sampling variance, whether the sampling regime is time-based or mass-based. This is an obvious simplification of the real state of affairs and it is worthwhile to study this impact via simulation.With a facility to simulate large (long) random functions having some thousands of points in the function and the ability to impose covariance functions on the mass flow and analyte variations, such a study is possible. It is also possible to evaluate the impact of correlation between analyte content and mass flows.This paper describes a limited study of the variance increase due to mass flow fluctuations over the usual sampling variance due to analyte variation during the sampling period. The bias in the sampling result is determined for specific modes of correlation. Simulation methods are used as they are the only means by which a sampling result can be compared to the true assay for the lot; in the physical circumstances of mineral process analysis, it is never possible to determine the true process stream assay.CITATION:Lyman, G J, 2017. The impact of the weighting error, in Proceedings Eighth World Conference on Sampling and Blending , pp 311–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

Fragmentation Characteristics of Iron Ores from Anshan, China

Sep 13, 2010

By Silvio Hernández Aquije

El presente texto señala el descubrimento del yacimiento vanadífero de Minasragra a través del reporte de Yeatman-Berry en 1916 y el de Kett-Sproul en 1931. Así también señala los tipos de mineralización como la mineralización primaria y por impregnación.

Jul 1, 1955

By Ke Yang

Drilled shafts are widely adopted as the foundation for sound walls. However, there has been a lack of uniformity in design and analysis methods and design criteria, in terms of factor of safety against ultimate capacity failure as well as the allowable deflection. In order to establish a uniform design methodology for the drilled shafts supporting sound walls in cohesive and cohesionless soils, respectively, a database of full-scale lateral load tests on fully instrumented drilled shafts was collected. Based on the compiled database, existing design methods and design criteria of laterally loaded drilled shafts were evaluated. Broms method and COM624P (or LPILE) are suggested as the design methods for drilled shafts supporting sound walls in both cohesive and cohesionless soils. Additionally, the corresponding design criteria, including factor of safety and permissible deflection, for both design methods are recommended. Two full-scale lateral load tests on fully instrumented drilled shafts were subsequently conducted in Colorado to further verify the design recommendation. A comprehensive geotechnical investigation program was also carried out at the two new lateral load test sites that included pressuremeter test, SPT, as well as laboratory triaxial consolidated undrained tests and direct shear tests on the soil samples taken from the lateral load test sites. The test results obtained at these two load test sites were employed to validate the recommended geotechnical design and geotechnical testing methods for the drilled shafts supporting sound walls.

Jan 1, 2007

By R. R. Sayers

The increasing use of hydrogen fluoride (annual consumption now exceeds 500,000 pounds (1)4/) directly and its occurrence as a byproduct of the utilization of fluorine compounds in the mineral industries, especially in metallurgical processes and in the refining of petroleum products, has aroused interest in its toxicity, and a brief review of the literature, with special reference to the hazard of poisoning in the mineral industries, seems to be opportune. Recently, residents in the vicinity of aluminum plants have been complaining of injury to livestock and vegetation as well as to their own health from the gases discharged into the air during operation of the plants, hydrofluoric acid gas apparently being the offender. The comparatively recent utilization of hydrofluoric acid in the alkylation process for the production of high-octane gasoline has raised the question of the hazard of poisoning in the petroleum Industry. In addition, the use of fluorine-containing refrigerants has extended the potential al exposure outside of industry (2).

Jan 1, 1945

By William F. Keyes

Greensand, which is widely distributed in the Eastern United States, was produced in 1975 only by Inversand Co., a subsidiary of Hungerford & Terry, Inc., near Clayton, N.J. Production and sales information are not available for publication. Raw greensand produced by the company was sold for agricultural use as a soil conditioner. Processed greensand was used by manufacturers as filter media in equipment for the removal of manganese, iron and other elements from water. The University of Delaware received a grant of $17,051 from the Bureau of Mines early in 1976 to continue its studies of the effectiveness of greensand in removing metallic contaminants from waste waters.

Jan 1, 1977

By Za-Chieh Moh

This paper presents a summary of the current pile foundation practice in Taiwan. Constructions of driven piles, drilled shafts, and barrette foundations are reviewed. This paper also briefly summarizes the pile works of four major construction projects in Taiwan, namely, Hsin-Ta Power Plant, Taichung Power Plant, Taipei Transit Systems, and Taiwan High Speed Rail.

Jan 1, 1996

By Frank Chase, M. Terry Hoch, George Karabin, Joseph C. Zelanko, Christopher Mark

Pillar recovery continues to be a significant ground control hazard. During the past decade, 10 miners were killed during pillar extraction operations in southern West Virginia. Studies conducted during the past decade have identified a number of “risk factors” that can be used to evaluate pillar extraction plans: •Cut sequence •Final stump •Timber or Mobile Roof Supports •Roof bolting •Intersection span •Depth of cover •Roof quality •Age of workings For each of these factors, rock mechanics science suggests which alternative would be expected to be more risky. For example, numerical models were used to evaluate different cut sequences, and indicated that less roof convergence occurred with the outside lift method than with the Christmas tree in the particular environment simulated. For many of the risk factors, accident statistics confirm the science. One finding was that currently almost 70% of the retreat coal in southern WV is being mined with MRS. In contrast, timber supports were used in 70% of the past decade’s pillaring fatalities. This paper discusses each of the risk factors in turn, presents the relevant accident statistics, and shows how the risk factors can be combined to estimate the overall hazard. It also addresses the use of pillar design to minimize the risk of global stability hazards including squeezes, massive collapses, and bumps.

By W. G. Davenport, M. Paneni

Experiments in sheets of mercury and water have confirmed that the dynamics of bubble rise are simi-lur in Liquid metal and aqueous systems. RECOGNITION that bubble/metal interactions are important in pyrometallurgical refining processes (e.g., steelmaking, vacuum degassing, deoxidation of copper) has led to a number of investigations into the dynamic behavior of bubbles rising in liquid metals. Terminal velocities of bubbles rising in mercury (20°C)&apos; and silver (1000" to 1050"c)1,2 have been measured. Good agreement between aqueous and liquid metal systems has been obtained. Shapes of air bubbles rising in mercury have been determined experimentally by Davenport, Bradshaw, and Richardsonl who used a system of electric probes to measure maximum horizontal and vertical dimensions, Fig. 5. In the present work the motion and shape of nitrogen bubbles rising in a thin sheet of mercury (i.e., a "two-dimensional" environment) have been studied with the view of confirming dynamic similarity between aqueous and metallic systems. The use of thin sheets of liquid permitted direct visual and photographic comparisons of bubble behavior in clear liquids and in mercury. EXPERIMENTAL METHOD The thin sheets of mercury or water were held in a clear acrylic plastic container, Fig. 1. The sheets of liquid were 80 cm high by 30 cm wide and 0.47 cm thick. Single bubbles were formed by injecting the desired volume of nitrogen into an inverted semicircular cup (stainless steel). The cup was then rotated into the upright position using an external handle thus releasing a single bubble of measured volume. Nitrogen was injected into the cup from a nitrogen cylinder through the external handle and a hollow rotating axle. The volume of a bubble (volume range 0.01 to 10 cu cm) at any instant was obtained by connecting a soap film meter to a small gas space above the liquid. By this technique any change in the volume of a gas bubble in the liquid (i.e., during cup filling or during rise) produces an equivalent displacement from gas space A into the buret B. This displacement is determined by measuring the movement of a horizontal soap film in the buret. Bubble shapes were determined using single-frame photography. Rising velocities were determined by cinephotography with a 1/100-sec stopwatch in the field of view. In both cases dimensions were referenced to a rule attached to the container surface, also in the field of view. Linear dimensions were measured on projections of the single-frame negatives. Rising velocities were calculated from measured heights of rise (10 to 20 cm) and times of rise. The effects of disturbances caused by cup rotation and by bubble release were minimized by photographing bubbles at a point not less than 25 cm above the cup. MATERIALS Mercury: Technical-grade purified: minimum 99 pct Hg; Johnson Matthey and Mallory Limited, Toronto. Nitrogen: Technical-grade purified nitrogen: 99.99 pct Nz, 0.01 pct 02, trace argon; Air Liquide Canada Limitee, Montreal.

Jan 1, 1970

By . M. Muskat

A THEORETICAL consideration of the mechanics of various water-flooding systems with the viewpoint of comparing their relative merits involves the study of two fundamental properties of such systems. On the one hand, it is important to determine the efficiency of the flood as measured by the percentage of the total area that is swept out by the encroaching water before water actually reaches the output wells. This is really a measure of the regional tendency of the water to "bypass" the oil. On the other hand, the various systems must be compared from the viewpoint of their resistances which determine the rate of fluid production obtainable for given pressures maintained at the water input wells. The first of these questions has been studied and very definite answers have been obtained by means of simple electrolytic models.1 These models showed that, in an ideal system, the percentages of the areas flooded out before water reaches the output wells are about 57 per cent for the direct line-drive flood (the input and output wells being equally spaced and placed in alternate parallel lines), 74 per cent for the regular five-spot network, and 79 per cent for the seven-spot network. With respect to the efficiency of the usual flooding arrangements, they are, therefore, given quite accurately by the above numbers. With regard to the resistances of the flooding networks, electrical conduction models have also been used successfully2 and are well adapted to the problem of determining experimentally the pressure distribution and streamlines, or over-all resistances of specific flooding networks. However, such models do not permit readily a study of the effect of changing dimensions or configuration within a network, since a new model must be made up for each set of dimensions considered.

Jan 1, 1933

By D. S. Kieffer

Ground characterized by hard boulders embedded in soft matrix represents one of the most challenging conditions for TBMs, as the cutterhead must cope with the non-optimal conditions of cutting hard blocks while simultaneously excavating through soft, soil-like matrix material. Dowden and Robinson (2001) and Hunt and Mazhar (2004) summarize several case histories relating to the problems of advancing a TBM through boulder-laden ground and provide guidance with respect to appropriate site investigations and baselining strategies. Some rock types constituting boulder-laden ground include: ?Sedimentary Rocks?cemented alluvial channel deposits, colluvium/talus, landslide debris, and glacial till. ?Igneous Rocks?agglomerates, lahars, and pyroclastic deposits. ?Metamorphic Rocks?tectonic mélange and cataclastic fault zones. ?Decomposed Rocks?corestone bearing saprolites. Disc cutters are commonly utilized to cut the hardblocks; however, as compared to the understanding of disc cutter behavior in hard continuous rocks, little is known regarding fundamental cutting mechanisms in highly heterogeneous bouldery ground conditions. To advance this understanding, a suite of full scale tests have been performed using a linear cutting machine at the Colorado School of Mines (CSM). This paper summarizes the observed cutting mechanisms and their practical implications for TBM excavations through boulder-laden ground.

Jan 1, 2008