Search Documents

This paper presents the near-field rock damage owing to production blasting in limestone quarry in the western region of Japan. The study's purpose is to learn the mechanism of crack development due to blast vibration. In this study, blast vibration's magnitude was expressed with peak particle velocity (PPV) which was obtained based on seismographs recorded database. In attempt to pursue a research's purpose of this study, there were two considerable interests: near-field blast vibration propagation and prediction, and crack observed and prediction. Furthermore, with regards to considerable interest of the study, there were three essential aspects which were challenged, such as: monitoring and interpretation of seismic wave propagation in a rock mass near large explosive charge of production blast scale, measurement of blast rock damage in adjacent to blasthole, and determine critical value of PPV which may produce significant rock damage. In order to determine precision critical PPV, understanding correlation between rock damage with vibration level is firstly important to be done. This paper also discusses how to measure, detect and quantify near-field blast vibration and blast rock damage in adjacent to blasthole.

Dec 6, 2010

By Reda M. Bakeer

"Measurements obtained during load testing of two steel H-piles driven at a site in Northeastern Mississippi are discussed. The general site conditions, equipment used, testing procedures and results of the pile load tests are presented. Both piles were tested in compression and one of the piles was subsequently tested in tension. The piles were instrumented with strain gauges and extensometers to measure the mobilized soil resistance and pile movement. Three different “zero strain” conditions were used to determine the mobilized soil resistance and residual loads due to driving or a load cycle. It was concluded that the effect of residual loads on driven piles could be significant. Driving residual loads influenced the magnitude and distribution of the load transfer curves more than those due to a load cycle. Results of the tension test were impacted by the residual loads from the previous compression test performed on the same pile.INTRODUCTIONSeveral factors affect the performance of a deep foundation system including the subsoil conditions, loading settings, pile type and installation method. Residual stresses develop in piles particularly due to pile driving, but they are typically not accounted for in the analysis (Fellenius 2002). Siegel and McGillivray (2009) presented an assessment of residual loads measured during load testing of instrumented auger-cast-in-place (ACIP) piles. The magnitude and distribution of residual stresses along the pile shaft and toe depend on the pile installation method, previous load cycles and time effects. Poulos (1987) reported that residual load due to driving at the pile toe is independent of pile driving equipment and may significantly affect the results of a pile load test. Hunter and Davisson (1969) reported results of pile load tests performed in compression on fully instrumented piles driven in cohesionless soils along with a discussion of the effects of residual loads. Tension loads of about 445 kN (100 kips) were measured at the pile toe after driving. Unloading residual compression load at the toe was detected as “apparent” tension since the instrumentation was zeroed prior to the test. The researchers suggested a graphical approach to obtain the “corrected” load distribution curves considering that residual load will dissipate following the tension test. Holloway et al. (1975) conducted a study on the effect of residual stresses due to pile driving and developed a computer software that accounts for residual loads. Briaud and Tucker (1984) suggested a method to account for residual loads based on the results of 33 pile load tests performed in mostly cohesionless soils."

Jan 1, 2017

By Bradford F. Townsend

A study was made on six collapses that occurred during large-diameter tunnelling through weak sedimentary rocks and soil using SES methods in three stages?top heading, bench and invert. The collapsed lengths are between 20 m and 277 m. The collapses were re-mined using essentially the same tunnel-ling method with larger excavation profiles to accommodate the designed remedial measures consisting of ground treatment, pre-support and stronger initial support/outer lining required to carry higher ground loads acting in the collapsed lengths. The paper presents information on the collapses and the design and execution of the remedial measures.

Jan 1, 2008

TowerMill - Advantages in Wet Grinding Applications The TowerMill, which has now been in existence for no less than 50 years, is one alternative to the horizontal ball mill and offers several advantages. The TowerMill is widely used in (coal-fired) electric power plants for the grinding of raw material for the FGD (Flue Gas Desulphurisation) process involving very high throughputs, very fine product sizes and high availability. Some companies in the mining industry also looked at the use of such optimised grinding machines several years ago and found that many of the advantages offered in other industries are transferable to new applications. Much development work has been undertaken to improve the TowerMill for new applications and, as part of that work, tests have also been conducted to make direct comparisons of their performance with that of ball mills. Grinding tests were performed using the same raw materials and comparable machine sizes. Some of the results are discussed in this paper, along with a comparison of the advantages and disadvantages. The conclusion provides an outlook for some worthwhile future applications. The test results, which are described and analysed, show that the TowerMill offers significant advantages in relation to operating costs and operational safety. An example based on the wet grinding of limestone is presented.

Sep 13, 2010

By Brent C. Jellicoe, Phil Robertshaw, J. Murphy, Peter Williamson

Kimberlites and associated diamonds have been the focus of extensive exploration in central Saskatchewan since 1988. During 1989, Uranerz Exploration and Mining Limited identified 71 shallow magnetic anomalies in the Fort a la Corne area from detailed aeromagnetic surveys. By the end of 1991, 18 of these targets had been proven, by drilling, to be kimberlite bodies encased within Cretaceous sedimentary strata. From 1991 to 1997, the number of drill-confirmed kimberlite bodies increased to 69. Our current view, drawing on an integration of geophysical and geological information, is that the kimberlites are composed of individual bodies and multi-vent clusters of coalesced bodies, all apparently constructed of stacked, temporally distinct layers of pyroclastic crater-facies kimberlite. Diamond recoveries and geochemical results from associated heavy minerals at Fort a la Corne remain highly variable, although continued minibulk sampling is expected to improve the estimation of diamond grades for the most prospective bodies.

Jan 1, 2001

By D. Arentsen

Changing environmental laws, new operating requirements and the increasing accuracy with which the bearing capacity of driven piles can be calculated have all led to the development of hydraulic piling hammers, some very primitive, others very advanced. Users find it difficult to decide which model is the most suitable, because the specifications are neither uniform nor unamiguous. There are no standard specifications and, moreover, the majority of hammers are suitable only for a limited range of applications. For the user, however, it is important to choose a hammer which will meet future as well as current requirements and will not quickly become obsolete or be unsuitable for a particular job.

Jan 1, 1987

One of the most common critical areas of longwall mining in terms of ground stability are the gateroad and bleeder entries. These critical entries provide much-needed safe access for miners and allow for adequate ventilation required for dilution of hazardous airborne contaminants and must remain open during mining of a multi-panel district. This paper focuses on the stability of the longwall entries subjected to a single abutment load such as bleeders, first tailgate, and last headgate. First tailgate and last headgate are also referred to as blind headgates and tailgates. A study of a longwall district through conditions mapping, support evaluations, and numerical modeling was conducted and evaluated by researchers from the National Institute for Occupational Safety and Health (NIOSH). The condition mapping and support evaluations were performed on entries that spanned the previous five years of mining and relied on a diverse selection of supports to maintain the functionality of the entry. Numerical modeling was also conducted to evaluate various support types with further investigation and comparison to the condition mapping. The study demonstrated the importance of the abutment load decay versus distance from the gob edge, the potential for a reduction in material handling related injuries, as well as optimal usage of secondary and standing support.

Jan 7, 2020

By Joshua Hoffman, Braden Lusk, Kyle Perry

This study explores how different geometries affect the shock tunnel’s performance and is broken down into three phases. Phase 1: Open arena testing in which theoretical energies produced by the detonation of small (<1.0 kg) charges are compared to actual experimental values. Phase 2: Shock Tunnel testing in which realized energies are experimentally recorded for the UK and S&T shock tunnels. Phase 3: Analysis of the data to begin building a pressure-forecasting tool for the UK shock tunnel given the explosive characteristics, sample size and desired pressure and impulse.

Jan 1, 2009

By Haiping Sun, Samir Ganguly, Oleg Ostrovski, M. Yaser Lone

Wettability of graphite by synthetic SiO2-Al2O3-CaO-MnO slags with varied MnO content and by industrial slags was studied at 1350-1600 °C using sessile drop method under argon atmosphere. Initial contact angle was the lowest (110-115o) for the MnO-free slag. For slags with 10-40 wt% MnO, the initial contact angle was in the range 125-135o. The contact angle decreased with the contact time. The change in the contact angle with slag mass was found insignificant. The surface tension of slags obtained from the drop shape analyses was 500-800 mN/m and varied in a narrow range with temperature and MnO concentration. The reduction rate increased with increasing MnO content in the synthetic slag from 20 wt% to 40wt% and temperature. Increasing temperature also increased the rate of reduction. No correlation was observed between the reduction rate and MnO content in the synthetic slags in the range 0-20 wt% and in the industrial slags. The rate of SiO2 reduction from the molten slag was close to the rate of MnO reduction. The MnO-free slag had the largest contact area with graphite substrate. Keywords: reduction, wettability, graphite, slag, manganese, surface tension.

Jan 1, 2007

By I. S. Thompson

"Exploration properties form a continuum from grass roots to those with favourable geology, geochemical and/or geophysical anomalies, mineralization, showings (prospects), and finally to those with defined mineral deposits. Often, properties exhibit a composite of these categories.The most problematic to value are properties or deposits that are not economically exploitable at the time of the valuation due to a lack of exploration, insufficient grade or tonnage, poor mining conditions, or the imposition of socio-economic, environmental, or legal constraints.Various acceptable methods of valuing the range of all such mineral properties or deposits are reviewed. Some less appropriate methods are also discussed."

Jan 1, 2002

By Thiago Félix dos Santos

A maioria dos materiais poliméricos sintéticos apresentam superfícies quimicamente inertes, isentas de porosidade e baixa energia de superfície. Este trabalho tem como objetivo realizar a modificação superficial do substrato têxtil de forma a aumentar a sua molhabilidade. Os tecidos de poliéster são hidrofóbicos e, por isso são desconfortáveis aos usuários, pois a fibra não absorve o suor do corpo, outro fator que é prejudicado pela hidrofobicidade da fibra de poliéster é o tingimento das mesmas. Portanto, tratamentos superficiais vêm sendo utilizados para minimizar esse problema e o plasma é uma técnica que se mostra bastante eficaz. O plasma ao interagir com a superfície do substrato provoca alterações químicas e físicas melhorando suas propriedades. Portanto, através do plasma é possível alterar as propriedades físico-químicas das superfícies de tecidos de poliéster, tendo como resultado o aumento da hidrofilidade dos mesmos com o incremento de grupos funcionais polares e o aumento da rugosidade em sua superfície. As amostras foram tratadas em um reator de plasma de barreira dielétrica a pressão atmosférica, em diferentes tempos de tratamento e voltagem. Após as funcionalizações as amostras foram submetidas ao teste de capilaridade, a fim de observar a melhora na hidrofilidade. Todas as amostras tratadas tiveram aumento na molhabilidade, com exceção, as amostras tratadas com 10 kV, onde não houve alteração.

Aug 7, 2018

By J. F. Archibald

A research effort has been undertaken, under Workplace Safety and Insurance Board of Ontario (WSIB) sponsorship, to characterize the support capabilities of conventional and innovative spray-on lining materials for mitigating dynamic failure effects created by simulated rockbursts. Conventional spray support media, such as shotcrete and fibrecrete linings, and a variety of new spray-on lining materials [thin, spray-on liners (TSLs)], typically polymer-type thin coatings, were subjected to simulated rockburst influence. For baseline comparison, conventional rockbolt and bolt-and-mesh support products were also evaluated. Observation of lining performance was undertaken through completion of field-scale support and rock detonation trials. Controlled blasting tests were conducted at the Queen’s University Explosives Laboratory to examine the effectiveness of the variety of surface coating agents for modifying dynamic rock spalling processes. All tests were performed upon largely undisturbed and homogeneous rock materials in highly repeatable fashion. All blasts were observed seismically and photographically to provide detailed information concerning rock motion, surface fracturing, ejected fragment motion and support liner survivability characteristics. These material comparison trials were performed to assess the relative effectiveness of a wide range of currently available area support techniques for suppressing hazards associated with dynamic rock ejection. The results of this study validate that thin, spray-on linings may be equally as effective, and often better, than conventional support materials at mitigating rockburst or like damage in highly stressed mine environments.

Jan 1, 2004

By G. I. McPhail

The authors have conducted several investigations into the prediction of the beach profile of high-density tailings and have found that there are a number of important considerations that need to be taken into account over and above the reliability of the beach profile prediction methodology. These considerations relate to the chemistry of the slurry and specifically the influence of pH and flocculation, both of which have a significant influence on the rheology of the slurry at the discharge point. A number of examples are discussed and a potential testing protocol that will assist in assessing the influence of chemistry ahead of the beach profile predictions is presented. A methodology for assimilating the results of the testing into the likely field situation is discussed, and suggestions are made on application of the results in beach profile prediction. The suspected influence of residual flocculation on the stratification

Jan 1, 2012

By Staff

The goal of the U.S. Bureau of Mines diesel engine research program is to reduce exhaust emissions from diesel-powered equipment used in underground mines. This research has led to significant advances in aerosol measurement and to the development of more effective emission controls. This Information Circular contains reports of some of the presentations made at the Bureau&apos;s Information and Technology Transfer Seminar on Diesels in Underground Mines given in Minneapolis, MN, on September 29-30, 1992. The seminar emphasized the measurement and control of diesel particulate matter emissions. Topics covered include a discussion of the health issues associated with the use of diesel equipment underground, an overview of regulations, measurement techniques for diesel exhaust aerosol, levels of diesel exhaust pollutants found in mines, and modern emission controls. An appendix is included that contains a report describing the capabilities of the Bureau&apos;s diesel emissions research laboratory, two papers describing the effects of engine maintenance or: emissions, a paper describing the monitoring of carbon dioxide in mine air as an indicator of air quality, a glossary, and a list of abbreviations and acronyms.

Jan 1, 1992

By G. W. Poling

This paper evaluates current environmental protection legislation, guidelines and criteria, focusing mainly on the land and water disposal of mill tailings. Effluent criteria and regulatory mechanisms are proposed, and submarine tailing disposal is discussed at length. The importance of basing regulations on the best available rationale is stressed.

Jan 1, 1979

By A. L. Podia

The purpose of this research was to develop a system capable of detecting changes in the structure of rocks, leading to failure of mine roofs, and/or excavations. A prototype system was developed, field tested and delivered to the United States Bureau of Mines for further evaluation and research. This system is based on the analysis of acoustic signals generated on the surface of the roof by an impact device and which are reflected or backscattered by flaws and discontinuities in the rock. The specially designed impact source is capable of generating high frequency acoustic signals with excellent repeatability. The system can also be used in conjunction with conventional acoustic pulse transducers. The received signal is digitized and the data transferred to a minicomputer for processing and display. This capability allows the immediate determination of wave velocity and/or distance to a reflecting interface. Various data processing techniques such as averaging, differentiating, and comparing of different signals can be selected by entering the appropriate commands on the keyboard. Being a programmable system it is possible to implement more advanced signal processing techniques. All results as well as the signal are displayed on a CRT. Furthermore, a permanent record of the data can be generated on paper tape, which can be reentered and processed at a later date. A communications interface allows transmission of the sampled signal to a large scale re-mote computer. The system was tested extensively in the laboratory, and field tested at the York Canyon Coal Mine. These tests proved the feasibility of operation in the mining environment. Results indicate that further investigation and development will have to be undertaken to fully develop the potential of this system in satisfying the goals of this research.

Jan 1, 1973

By Jorge Maldonado Villa

Se desarrollaron materiales compuestos de matriz polimérica para toberas en cohetes; con dos zonas: una térmica para soportar elevadas temperaturas de combustión y una estructural que resista los esfuerzos generados. La zona térmica se elaboró con materiales de comportamiento ablativo, probados a temperaturas de hasta 2950°C durante dos minutos, los cuales fueron reforzados con polvo cerámico y/o subproducto de la industria siderúrgica (cerámico 2). Con base en los resultados obtenidos del comportamiento de térmico y de conductividad térmica del material ablativo, se construyó la zona estructural en materiales compuestos fibroreforzados (vidrio y carbono) con matriz polimérica. Los moldes se diseñaron en SolidWorks y se fabricaron por prototipado en ABS rápido y se elaboraron machos disgregables en poliuretano. En la zona térmica se usó un procedimiento de vaciado con vibración con diferentes tipos de matrices (poliéster, vinilester, caucho silicona) y de laminación para la zona estructural. Se evaluó el desempeño mediante simulación de las condiciones reales de operación mediante llama de oxicorte y quemador de ACPM, observando el efecto en la pérdida de peso, espesor, diferencial de temperatura, cambio de propiedades mecánicas, etc.; encontrándose un positivo comportamiento del sistema con matriz de resina vinilester reforzado con polvo cerámico 1 y buenos resultados con cerámico 2, así como una estabilidad en la zona estructural construida con fibras de vidrio y carbono. Substituir todo o texto de orientação deste Template pelo conteúdo de seu trabalho. Inserir o texto com no máximo 1.500 caracteres (200 palavras), sem uso de parágrafos. Deve conter, de maneira concisa, o objetivo, a metodologia, os resultados e as conclusões do trabalho.

Aug 17, 2017

By Henry S. Washington

Introduction. It Still Rains On The Choco ! I Well Remember One Evening A Dozen Years Ago, While. Traveling Toward The Town Of Negua In A Small Champa Or Dug-Out Canoe, The Rain Fell So Heavily That I Had To Work My Hardest To Bail Out The Water With A Large Totuma Or Gourd In Order To Keep The Canoe Afloat, The Senegambian Meanwhile Plying His Paddle In The Stern. If Any One Thinks Bailing Is Easy Work, Let Him Scoop Out A Quart Or More At A Stroke, 40 Times A Minute For Half An Hour, And I Venture That He Will Change His Opinion. These Small Canoes Required Only One Paddler, To Make The 3 Miles An Hour Which Is The Standard Rate Of Aquatic Progress On The Choco. Another Time, On The Atrato River, About Six O&apos;clock In The Afternoon, The Rain Fell So Heavily Than An Empty Gourd, 9 In. In Diameter And 4.5 Deep, Was Filled To The Brim In 90 Sec., Timed By A Watch. Such Downpours Are Typical, But Unless Caught In One It Is Not Specially Noticed. These Downpours Seldom Last More Than An Hour, And Frequently Cover Only A Limited Area, Occasionally Falling On One Bank Of A River And Not On The Other. During The Night-Time,&apos; The Rain, If Gentle, Will Usually Last Until Dawn, And Sometimes An Intermittent Drizzle Will Keep Up All Day As Well, Although, As A Rule, It Rarely Rains During The Day. The Rise Of The Rivers, Due To The Rain-Fall, Varies From A Few Inches To Several Feet. One Night In August, 1899, The Spuds Of The Dredge Margaret, Operating On The Atrato River, Showed A, Rise Of 16 Ft., And For 3 Days Thereafter Occurred The Greatest Flood Known In That District For 32 Years. The Dredge Had All Three Spuds Clown, And The 2-Yd. Shovel Dragging On The Bottom. A 0.75-In. Cable Fast To A Stout Tree, 700 Ft. Away, Stretched Tight

Sep 1, 1908

Helium has probably aroused more varied scientific curiosity than any other single element. Discovered by spectroscopic examination of the sun during an eclipse in 1868, helium is now known to exist not only in the sun and other stars but on earth occluded in minerals, accumulated with natural gases in pockets in the earth&apos;s crust, and in the atmosphere surrounding the earth. Astronomers study its presence in the various stars of the universe for clues to their origin and history. Geochemists and geologists study its occurrences in rocks, minerals, and meteorites to determine the age of the earth and the manner of its formation. Pathologists study its effect on living tissues in search for the ideal combination with oxygen for artificial breathing mixtures in medicine, diving operations, and space vehicles. Chemists study its physical properties and use it to trace the sequence of events in reactions in which it does not participate. Geneticists and bacteriologists use it for special studies. Physicists study its behavior when liquefied and the behavior of materials cooled to nearly absolute zero by its use. Nuclear physicists learn more about the universe through study of the nuclear reactions that produce it. Through study of helium and greater knowledge of its origin and properties, science continues to unlock some of nature&apos;s more closely guarded secrets. Unknown on earth before 1895, and not discovered as a minor constituent of natural gas until 1905, helium with its simple atomic structure--a nucleus with two electrons orbiting in a closed shell--is a unique element. It is next to the lightest gas, only hydrogen is lighter. It occupies position number 2 in the Periodic Table of the Elements and heads the list of so-called "rare" or ?noble? gases. Most of the naturally occurring helium has an atomic mass of 4.003874 (oxygen = 16). A trace (1.7 x 10-5 mol percent) is the light isotope helium-3 whose atomic mass is 3.0169800 Unstable isotopes of mass numbers 5 and 6 have been authenticated. Isotopes of mass numbers 7 and 8 have been reported, but their existence is less well established. All the heavier isotopes are radioactive and are the product of nuclear reactions.

Jan 1, 1968

By A. Broussaud

An original methodology has been developed for steady state simulation of selective grinding and mineral liberation in rod and ball mills. Three fundamental aspects of the methodology are presented successively : modeling ore texture, modeling grinding and its selectivity, and modeling mineral liberation. The methodology for modeling ore texture includes the conversion of 2D data into 3D reconstructed information and the use of the BILCO coherent material balance software. The models for grinding Simulation are classified into three levels, corresponding to three levels of available experimental data. All models account for grinding selectivity and for variations of engineering para-meters and operating conditions. An algorithm has been introduced to forecast mineral liberation, compatible with accurate simulation of selective grinding, which generates reasonable results.

Jan 1, 1987