Search Documents

By J. M. N. P. C. Teles, Venda Oliveira P. J., Correia A. A. S.

"AbstractA laboratory work was performed to study the mechanical behavior of a Portuguese soft soil chemically stabilized with binders and reinforced with metallic fibers when subjected to tensile stresses. To this end and in order to compare the tensile strength results done by two different tests, there were conducted two types of experimental tests: Tensile Split Strength Tests (TS) and Direct Tensile Strength Tests (T). The samples tested had the same binder quantity and different fiber contents, which allowed the characterization of the tensile behavior of the stabilized and reinforced soil, as well as the definition of the best fiber content. Results show that the binder is the main parameter controlling the behavior of the stabilized and reinforced soil until failure, while the influence of the fibers is noticed mainly at the post-failure behavior. The comparison between the tensile strength done by T and TS tests shows that the tensile split test can be used to estimate the tensile strength, although its results are lower than those obtained by the direct tensile tests in general.IntroductionDue to its poor mechanical characteristics, the construction on soft soils presents difficulties that require the use of soil improvement techniques such as chemical stabilization. However, even when mixed with binders, the tensile strength of the stabilized soil is poor, requiring, in certain cases, the use of expensive steel reinforcement or metallic beams, with obvious impact on the final cost of the work. Thus, for the cases where the tensile strength is a design requirement, the soil stabilization should be design with another element, whose primary role is to give tensile strength to the improved soil (Teles 2013).To fill the lack of published studies focused on soft soils both chemically stabilized and reinforced with metallic fibers, the present research aims to analyze the behavior of the improved soil when subjected to tensile stresses. To support the research there were conducted direct tensile tests (T) to directly measure the tensile strength of the samples and tensile split tests (TS) or Brazilian tests to obtain it indirectly. The samples tested had the same binder quantity but five different fiber contents in order to study the influence of the fibers in the improved soil behavior. In addition, a comparison between the results of both tests was made."

Jan 1, 2014

By O. P. Hood, R. H. Kudlich

When a gasoline locomotive is used in a mine there is danger of the noxious gases of the exhaust vitiating the air, but if enough air is circulating in those parts of the mine in which the locomotive is used, these gases are so diluted that they are rendered harmless, and the health of the workmen is not affected. In some mines the use of gasoline locomotives is impracticable, though in the majority of mines where they have been tried they have proved to be safe and economical. To determine the limitations that should surround the use of these machines in mines so that they shall not be detrimental to health and so that their economic advantage may be retained, it is necessary to ascertain the volume and the character of the exhaust gases and the amount of these gases that may be safely allowed in the mine air, and also to determine safe conditions of operation. The problem is primarily one of ventilation and like all ventilation problems must be intelligently computed to meet the conditions of each mine. The investigation described in this bulletin was undertaken 'by the Bureau of Mines in an endeavor to obtain exact information on some of the basal questions involved in the use of gasoline locomotives in mines, this investigation being one of many that the bureau has been conducting in its efforts to increase safety and efficiency in mining.

Jan 1, 1915

By D. C. Andersen, G. L. Smith, J. Pearson-Taylor

Following a restructuring of Anglo Platinum Limited in 2004 the strategic long-term planning function has been centralized. This paper describes the revised strategic long-term planning process covering aspects of the planning cycle, systems and methodologies, categorization of capital expenditure, corporate governance and planning tools.

Jan 1, 2006

By Paul V. Mullins

Review and evaluation of all available data on the vapor pressure of car-bon dioxide at the ice point, including previously unpublished results obtained by the Bureau of Mines, are presented. Suggested corrections and adjustments to all the data yield an average value of 26,136.4 mm mercury. Indicated agreement is within plus 1 part in 8,000 to minus 1 part in 11,000. A novel pressure bomb in which a sample of pure carbon dioxide is placed and sealed by a diaphragm fluid separator and its use as a reference pressure standard for extended and repeated use in the calibration of deadweight gages is described.

Jan 1, 1966

All previous attempts to cut rock in boring by means of revolving steel cutters have failed, chiefly in consequence of the mis-shapen teeth grinding the rock and themselves simultaneously, until, after a very few revolutions, the points of the cutters were so worn that it was impossible to force them into the strata. The diamond drilling plant being cumbrous, complicated, and costly, and seeing that fully 70 per cent of the boring generally needed is in what is known as the" milder strata," it will be readily understood that much of the work done will not pay a dividend on the outlay, so great is the cost of removal, the wear and tear of the machinery, and the loss of diamonds. The Calyx Drill, however, invented by Mr. F. Harley Davis, has been constructed so as to overcome these difficulties, and will penetrate quickly and .at a low cost this 70 per cent. of the milder strata. The Drill has taken ten years' hard work and thought to bring it to its present state of perfection, and it will now drill with steel cutters the 70 per cent of the work performed by the diamond drills at a greater speed and at about one third the cost of the latter.The utility of the diamond drill for certain work is undeniable, but it cannot by any means be described as a machine of general popular usefulness that is to say, it is quite beyond the reach of the great masses of mankind.

By Leonardo Bravo, Leonardo Almeyda

El desarrollo de proyectos de I&D es fundamental para maximizar la eficiencia del beneficiamiento de minerales. Por ello, Nexa Resources busca captar nuevas variables, controlar y optimizar los procesos minero – metalúrgicos mediante la implementación de modelos analíticos, y generar así escenarios virtuales capaces de anticipar condiciones operacionales futuras. Este artículo aborda los puntos más críticos suscitados durante la ejecución de proyectos de I&D en el sector minero – metalúrgico, e inicia detallando los pasos claves para diseñar un portafolio de I&D que permita optimizar uno o más KPI operacionales, y sea capaz de garantizar (i) la viabilidad técnica – financiera, (ii) la generación de valor en el corto plazo y (iii) una adecuada gestión del riesgo.

Sep 29, 2023

By Jacob Masliyah, Zhiang Zhou, Tshitende Kasongo, Jianjun Liu, Zhenghe Xu, Jeawon Choung

"Slime coating is a recognized challenge in fine particle flotation, not only in decreasing recovery, but also in reducing the selectivity and hence froth quality. In this presentation, a novel method based on electrophoretic mobility distribution measurement to study slime coatings is described. By measuring electrophoretic mobility distribution of individual minerals and their mixtures, the interactions between these minerals can be evaluated.For illustrative purposes, a model system of fine coals, or oil sands with two different types of fine clays was studied. Flotation tests showed a significant decrease in coal (bitumen) flotation recovery with montmorillonite but not with kaolinite clay addition. When electrophoretic mobility distribution of a fine coal/montmorillonite clay mixture was measured, a single modal zeta potential distribution was obtained, in contrast to a bimodal distribution for fine coalkaolinite clay mixture. This finding suggests a stronger adhesion of montmorillonite than kaolinite clays on fine coal surfaces. In the case of bitumen, the bimodal zeta potential distribution was measured for the mixture of bitumen emulsion and kaolinite or montmorillonite, indicating a weak attraction of the clays by bitumen. In the presence of calcium, however, a single modal zeta potential distribution was obtained in the mixture of bitumen emulsion with montmorillonite but not kaolinite clays. These findings are in excellent agreement with bitumen flotation results, demonstrating that the electrophoretic distribution measurement is a powerful tool to study slime coating phenomenon in a complex fine particle flotation system."

Jan 1, 2002

By David M. Spatz

The way people interact, collaborate, learn and improve can have a profound impact on a company’s efficiency, performance, productivity and return on investment. This is the motive behind corporate efforts today to replace the traditional hierarchical structure with team-oriented organization. The increased importance of communication and collaboration during the past 20 years has been propelled by rapid advances in technology and increased availability of information. Companies must take advantage of the information that is required for competitive performance and for the continued production of quality products. So it is essential that outstanding communication, cooperation and collaboration take place among multidisciplinary specialists assigned to work together to solve common problems and achieve common goals. Companies are searching for ways to increase knowledge transfer and learning, particularly among people who work on related topics. This will improve efficiency and quality and reduce redundancy and costs.

Jan 1, 2000

By Roberto Antoniolli

"IntroductionSINCE ancient times, the precious metals have played an important role in influencing the course of history. Silver and gold happened to occur, although in small amounts, in those countries where the early civilizations developed. Their persistent brightness certainly amazed the primitive people, who also found it easy to shape them into ornaments •and implements. Ever since then their properties have made them seem desirable possessions.Use of precious metals as money was the natural consequence of man's desire for them. The possibility of changing an ornament into a tool or food at any time, and the ease with which such medium of exchange could be carried and hidden, further increased the demand for the two metals.Silver was probably discovered after gold and copper, and was undoubtedly found by prehistoric man as native silver. The oldest silver articles have been discovered in Chaldean tombs and date back to 5000 B.C. The earliest ascertained producers of silver were Asia Minor and the Iberian Peninsula. The Romans worked deposits in Spain, Britain, and France. In the Middle Ages, some silver was extracted from German deposits, and near the end of the Middle Ages systematic workings were carried on at Freiberg, Schneeberg, and Joachimsthal (1).Before the discovery of the New Continent, the Aztecs and Toltecs in Mexico, and the Incas in Peru, had made extensive use of silver. In the 16th century the Mexican deposits became the largest source of the world silver."

Jan 1, 1954

Experimental results are presented for the anode overvoltage as a function of current density for different alumina concentrations in an alumina reduction cell. Voltage changes due to the electrolyte resistance and also the decomposition voltage, have been evaluated as a function of alumina concentration and anode current density. From these values of voltage, changes in the total cell voltage have been derived for changes in alumina concentration for different anode current densities. The results show that for each operating current density there exists a discrete alumina concentration that defines a minimum reduction cell voltage. Discussion is made about potential savings in power consumption when the alumina concentration is controlled.INTRODUCTIONThe standard procedure in the aluminium industry when analysing the cell-voltage required for the Hall-Heroult process for reduction of alumina, is to subdivide the total voltage into the following components (e.g. Pearson, 1955; Maritell, 1960).1. ohmic drop through busbars and joints2. ohmic drop through cathode lining3. ohmic drop through anode4. ohmic drop through electrolyte5. overvoltage at anode6. electrolytic decomposition voltage.(Overvoltages ,at the cathode are of negligible magnitude at all practical current densities.)It is understandable that the voltages assigned for each factor invariably differ for different workers...

Jan 1, 1965

By C. F. Cornell, R. C. Emmett, D. A. Dahlstrom

FOR many years the disk-type and cloth-covered drum filters have found widest application in liquid-solids separation, which uses continuous filters. The disk type is less expensive, occupies less floor space per square foot of filtration area, and requires negligible down time for filter media changing. However, because filter cloth is billowed out by the blowback in the cake discharge, it is very short-lived if the scraper blades are set too close. Consequently cake weight is very important in assisting cake discharge, which normally necessitates a minimum cake thickness of 3/8 to ½ in. Also, the vertical position of the disks eliminates the possibility of efficient cake washing for removal of soluble values. The disk-type filter is generally limited, therefore, to applications that require no cake washing and form relatively thick cakes within the normal range of filter cycle times. The conventional cloth-covered drum filter is a more flexible unit, permitting wider variation in the percentage of cycle time devoted to cake formation, dewatering, or washing, as required by the application. Thinner filter cakes can be discharged because a horizontal line across the filter medium at the location of the scraper blade is equidistant from the edge of the blade at all points. The scraper blade therefore may be set a short distance from the filter medium or, where wire winding is not used, a floating scraper can be utilized so that the contour of the cloth can be followed. The drum filter is generally employed when there are difficult filtering slurries with resultant thin cakes or when cake washing to recover soluble values must be practiced. Difficulties sometimes encountered in continuous filter operation can be summarized in the following four categories: 1) Low filtration and/or washing rates due to blinding of the filter medium. 2) Poor cake discharge resulting from sticky cakes, filter medium blinding, or too thin a cake for the particular type of filter. 3) High filter media costs caused by short life and frequent down times for cloth changing. This results from blinding or from abrasion by the scraper blade when cakes are thin. 4) Blowback of filtrate at cake discharge because not enough air passes through the cake to purge the drainage area and filtrate lines during dewatering. To reduce or eliminate blinding tendencies several modifications have been tried, for example, cover-cleaning showers, blowback under the feed slurry, and snap-blow cake discharge. In many cases, however, this simply retards the rate of blinding, since the filter medium is kept clean at its outer surface only by these methods. As blinding usually occurs within or on the back of the medium, the operator is finally forced either to remove the cloth and scrub the medium intensively with a cleaning solution or acid-rinse it on the filter—all resulting in down time, short cloth life, and additional costs.

Jan 1, 1959

By John Hoelle

Coal mines in southern West Virginia, south-western Virginia and eastern Kentucky have experienced coal bumps at least since 1933. Most of the bumps have occurred due to high cover, strong roof and floor strata and stress concentrations due to the mining sequence. A longwall mine in eastern Kentucky first experienced coal bumps on the tailgate side of the longwall face in 1989. The bumps continued until 1996. The bumps were the result of: Thick overburden up to 2200 feet Strong roof and floor (strata strengths up to 25,600 psi UCS and elasticity modulus up to 4,800,000 psi Previous over-mining in places Sandstone channels Not all characteristics occurred simultaneously. The bumps produced seismic events recorded up to 4.3 (Richter scale magnitude), and damaged pillars that were up to 147 by 152 feet in size.

Jan 1, 2008

By C Roche, G M. Mudd

The Morobe Province of central Papua New Guinea (PNG) has been mined for gold for nearly a century, although it is only in the past decade that large-scale modern mining commenced. The Hidden Valley gold-silver project began construction in mid-2006 and production by August 2009, and is located in the mountains above Wau in the headwaters of the Watut River. The mine is owned and operated by the Morobe Mining Joint Venture (MMJV), which also owns the Wafi-Golpu project, comprising the Wafi gold deposit and Golpu copper-gold deposit, situated in the Watut River Valley. Together they represent a potential mine of the scale of Ok Tedi or Bougainville or bigger. The MMJV is owned in equal shares by Newcrest Mining from Australia and Harmony Gold from South Africa. Although Hidden Valley was the first large-scale mine in PNG to engineer and build a tailings storage facility, poor environmental management during construction and early operations led to significant erosion of waste rock and sedimentation impacts throughout the ~200 km length of the Watut River. Since then, substantial efforts have been made to improve environmental management, especially waste rock placement and storage and water quality management. While the impacts from the Hidden Valley project appear to be reducing, the saga has heightened concerns by many along the Watut River and across PNG about ongoing impacts from mining.This paper presents the results of an ongoing project in the Morobe Province conducted by the Mineral Policy Institute examining the historical, current and future impacts of mining, including community views, social and environmental impacts and the monitoring and regulation of mining. Overall, there is a clear need to more fully integrate social and environmental issues into life-of-mine planning and go above and beyond regulatory requirements. In this way, some of the lessons learnt – by the community, MMJV and government – can be incorporated before, during and long after mining.CITATION:Mudd, G M and Roche, C, ?2014. Mining in Morobe, Papua New Guinea – impacts, assurance and self-determination, in Proceedings Life-of-Mine 2014 , pp 313–336 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By H. P. Rosenof

The G2 real-time expert system, a commercial product since 1988, is widely deployed in process, manufacturing and other industries. A number of innovative applications are installed or under development in the mining and metallurgical industries. These include: ? A chemical reagent control system for a mineral concentrator, at a mining company; ? A supervisory control system for a product dryer, at a surface coal mine ? A training system for equipment operators, at a steel mill; ? A scheduling system for furnaces at a hot rolling mill; ? A simulation system for mining operations; ? Several graduate-level research projects in materials handling at a university Realized and projected benefits will be discussed. In addition certain applications installed or under development in other industries will be proposed as applicable in mining and metallurgy. For example, applications for the management of vehicular traffic may find use in mining and shipping.

Jan 1, 1992

By G. S. Dobby, J. A. Finch

"I. INTRODUCTIONA significant development in flotation over the past few years has been the increasing industrial use of flotation columns, primarily in Canada. The column differs dramatically from conventional mechanical flotation machines, both in design end operating philosophy, which has been a principal reason for its slow acceptance by the mineral industry. Boutin, Tremblay and Wheeler (1. 2) developed the concept in the early 1960's and since then plant and laboratory columns have been marketed commercially by Column Flotation Company of Canada Ltd. In 1980-81 at Mines Gaspe, Quebec, three columns replaced 13 conventional cleaners in a molybdenum upgrading circuit, with superior results (3). Since then many of the copper producers in British Columbia have installed columns for copper and molybdenum cleaning, including Gibraltar, Lornex, Highmont and Island Copper. There now appears to be widespread interest in flotation columns.The column is particularly attractive for applications involving multiple cleaning stages and can upgrade In a single stage compared with several stages of mechanical cells. This results in simpler, more controllable circuits. Importantly, the column itself is well suited to computer control. A significant problem, however, has been that of translating laboratory data to plant performance. The purposes of this communication are to address the problem of column scale-up and to describe some of the transport mechanisms of a flotation column, leading to a kinetics based model.A schematic of a flotation column is shown in Figure]. Industrial columns are up to 13 m high and 0.3 to 1.8 m in cross section (either square or circular). Three zones can be identified:a collection zone, with feed entering 2 to 3 m below the top of the column and descending against rising bubbles generated at a gas sparger; a washing zone, where a packed bubble bed is generated by a downward flow of wash water; and a conventional froth (2 - 5 cm thick), the sole purpose of which is particle transport to the launder. The tailings withdrawal at the bottom of the column is controlled at a rate slightly greater than the feed flowrate (called a positive bias).An important element is the washwater, added just below the froth zone. The component of the washwater that flows downward (to make up the bias) is sufficient to prevent coalescence of rising gas bubbles. The packed bubble beg so generated is very efficient at suppressing gangue entrainment to the concentrate."

Jan 1, 1985

A description is given of preliminary work done to identify the problems inherent in electrochemical oxidation of metal sulphides, and particularly in the use of powder compacts as anodes in electrolysis. Lead flotation concentrate pressed into a compact can serve as an anode for direct electrowinning of lead according to the reaction PbS -7 Pb2+ +So +2e. No pYrometallurgical step is required, and sulphur is recovered in elemental form.In the experimental work, electrical conductivity of the compacts was achieved by addition of 5·5 per cent of graphite. After compaction at 10-20 tons/sq. in. the anodes were strong and remained intact throughout the electro-oxidation period. Perchlorate electrolyte was used, but fluosilicate electrolyte is also applicable. A sheet of pure lead formed the starting cathode.As anode potential increased above 1·0 V (v. SHE) PbS04 was formed in increasing amount. At 0·90 V, Pb2+ extraction efficiency was 85 per cent. Anode potential was kept low by electrolysing at 60°C and 15 mA/sq. cm., and by improving the porosity of the compact. Other metal sulphides (Zn, Fe, Cu) in the flotation concentrate also oxidize and release metal ions to the electrolyte, which would need to be purified prior to deposition of lead.Power requirement in a laboratory cell was about 0·24 kWh per lb of lead extracted.

Jan 1, 1972

In preparing this paper, the writer hopes to achieve two main objects. Firstly, an indication of the desirable features of coke from the viewpoint of a blast furnace operator should be of assistance and value to those connected with coal and coke research, coal mining, the manufacture of coke and the production of iron. Secondly, it is hoped that the conclusions and opinions expressed herein, which are known to be of a controversial nature, will promote some discussion and thought. In this way, other workers may see fit to contribute and enlarge our general knowledge of Australian coke and its behaviour in blast furnaces.Those properties of coke that are considered to be of importance to blast furnace operation will be examined. Although broadly speaking, the composition and characteristics of coke are inherent in the coals used, any special features of coal preparation and carbonization that affect the resultant coke will be discussed. An attempt will also be made to indicate the effect on blast furnace operation of significant irregularities in these properties.THE FUNCTION OF COKE IN A BLAST FURNACECoke has four important functions in a blast furnace:1. To reduce the oxides of iron and other elements to metal and to provide the carbon absorbed by the iron.2. To supply the necessary heat for the process.3. To provide an open supporting structure in which the descending ore and limestone lie exposed to the action of the ascending gas.4. To provide voidage in the bottom of the furnace, so that iron and slag can accumulate in the hearth.

Jan 1, 1957

By Bhaskar B. Thapa, Michael T. McRae, Johannes V. Greunen

This paper describes the preliminary design of the fourth bore of the Caldecott Tunnels along State Route 24 in Oakland, California. The paper focus is on two major aspects of the project: initial support system design and seismic design. The initial support system was designed based on the New Austrian Tunneling Method (NATM).NATM provides the required flexibility to accommodate the variable ground conditions in the weak, folded, and faulted rock along the alignment. The seismic design provides a final lining system that meets serviceability requirements for a 1,500 year seismic event with an estimated peak ground acceleration of 1.2g.

Jan 1, 2007

Ilmenite production in Western Australia commenced in 1956. There are now five producers, all in the Bunbury-Capel district, and current total production capacity is about 450,000 t.p.a.The deposits occur near the surface and average between 10 and 50 per cent heavy mineral. About 70-85 per cent of the heavy mineral is ilmenite. Other heavy minerals present include leucoxene, zircon, rutile, monazite, and garnet. The ilmenite contains 52-60 per cent Ti02. and is very low in chromium (0·03-0·04 per cent CrS03)Mining is done by sluicing, drag line excavation, or dredging. Primary concentration of the heavy minerals is achieved by spirals, revolving cones, or Reichert cones. After drying and screening, ilmenite is separated from the heavy mineral concentrate by various types of magnetic separator.Separate leucoxene, zircon, rutile, and monazite concentrates are also produced. Each plant uses a different technique and the processes used include chemical attritioning, screen plate electrostatic separation, high tension rolls, air tables, and dry launders.INTRODUCTIONThe treatment of beach sands in the Bunbury/Capel area for the extraction of ilmenite is a very recent development in the mining industry in Western Australia. Nevertheless, since the commencement of production in 1956, ilmenite has become the sixth most important mineral produced (Table 1).The increasing world recognition of Western Australia as a major producer of ilmenite (Table 2) is due primarily to the low chromic bxide content of the mineral (0' 03-0' 04 per cent Cr203), combined with a medium to high titanium dioxide content (54-60 per cent Ti02), supported by large reserves, a stable government, and close access to good shipping facilities. Ilmenite is. produced from these deposits at low cost which enables the industry to compete on world markets despite high rates for sea freights because of the distance from major markets.

Jan 1, 1965

THE object of the present paper is to give a brief description of the metallurgical process followed by the Grand Junction Co, and the results obtained therefrom. All figures quoted are from the actual working of the plant over a period of six months from January to June, 1910. The short ton of 2000 lb. is used by the company. Its gold is valued at 84s. per oz. fine, silver at 2s. per oz. fine. The ore consists essentially of a gangue of quartz and calcite, with 8 to 10%sulphide-pyrite, sphalerite, galena, chalcopyrite, and traces of arsenic and antimony. The colmtry-rock is a highlyaltered dacite. Small stringers of highly-mineralized ore penetrate the footwall of some of the lodes, forming a valuable stockwerk up to 3 ft. in thickness. In stoping, this is mined with the well defined lode, thus bringing into the mill at times a considerable quantity of hard country-rock. The gold exists in an exceedingly fine state of division, consequently rendering it necessary to grind very fine to obtain a satisfactory extraction.

Jan 1, 1912