Search Documents

By D. R. Murray

"In 2017, Nutrien Allan Potash remediated a portion of the concrete liner in the production shaft. A set of underslung work platforms and collection boxes were used in conjunction with hydraulic splitters, jackleg drills and hand chippers to excavate and remove the broken concrete. New concrete was placed with the original pressure relief design, using a shaft slip form. Shortly after excavating, it was found that the estimated breaking rate and amount of original concrete in-situ was under estimated. Fifteen feet of excavated concrete (2719cu.ft) and ten feet (of replaced concrete was completed on April 28, 2017, and operation of the production shaft was returned to mine operations. During February 2019, Nutrien Allan Potash began remediation of a portion of the concrete liner in the service shaft. The project is different than the 2017 project, as the remediation has occurred during normal running operations and occurred only on night shift. Rather than hydraulic splitters and hand chippers, the new method includes a concrete saw and mechanical excavator from a working platform. The selected method is based on the lessons learned from the 2017 project in the production shaft. The service shaft project was scheduled to be completed in July, 2019. INTRODUCTION Nutrien Allan Potash is located approximated 75 km east of the city of Saskatoon, Saskatchewan, Canada. There are currently two shafts at Nutrien Allan Potash: the Production Shaft and the Service Shaft, transporting people and material from surface to a depth of 3,335 ft. The Production Shaft was completed in 1967, with one section of grey cast iron tubbing installed in the Blairmore formation between the 1605 and 2037 ft Levels. A second set of cast iron tubbing was installed in the Duperow formation between 2203 and 2463 ft Levels in 1999. The remainder of the concrete as of todays standards is designed as a pressure relief liner. The Service Shaft was completed in 1968, with one section of grey cast iron tubbing installed in the Blairmore formation between the 1600 and 2048 ft Levels. A second set of cast iron tubbing was installed in 1981, with 169 ft installed through the Duperow formation. The remainder of the concrete as of todays standards is designed as a pressure relief liner. PRODUCTION SHAFT REMEDIATION During the second quarter of 2015, the Mine Engineering team were notified of an area of concern in the production shaft. The shaft specialists of Golder Associates Ltd (Golder, formerly Alan Auld Canada) were contacted to complete an inspection of the production shaft liner with emphasis on the area of concern. Based on the inspection and documentation review, it was determined that the concrete at the 2804 foot elevation had been broken out for some time and was retained with #8 rebar bolts with resin encapsulation. The broken concrete was encroaching on the clearance to the conveyance."

Jan 1, 2019

By E. McLaren, J. Sanftenberg, C. Cameron, H. Dello Sbarba

"A Ventilation on Demand (VOD) system has been optimized and maintained at Glencore’s Nickel Rim South Mine (NRS) in Sudbury, Ontario, Canada for the past seven years. The system monitors and controls air quality and quantity through real-time, dynamic automation of primary fans, secondary fans, automated airflow regulators, and air monitoring instrumentation with VentSim™ CONTROL, a VOD software. This paper will focus on the implementation of testing procedures and system maintenance methods. Overall, the results show a consistent reduction in energy usage.INTRODUCTIONThe Ventilation on Demand (VOD) system at Glencore’s Nickel Rim South (NRS) mine in Sudbury, Ontario, Canada, involves the control of two 2,980 kW centrifugal surface exhaust fans with Variable Frequency Drives (VFDs), three 335 kW vane-axial surface intake fans with VFDs, 21 automated airflow regulators, six automated dampers, seven automatic doors and 198 underground auxiliary fans with ON/OFF starters. Additionally, the system monitors airflow at 48 locations, carbon monoxide (CO) at 40 locations, nitrogen dioxide (NO2) at 21 locations, and dry bulb and wet bulb temperature at 21 locations. The VOD system is also integrated with a tagging and tracking system to modulate the ventilation system automatically and in real time according to the presence and position of the personnel and vehicles. The tracking system comprises of 75 vehicle tags with diesel status and hydraulic status (ON or OFF), 440 personnel tags, and 200 tracking zones. Finally, it also involves the configuration and updating of 55 level plan and interactive procedures and 24 daily scheduled events. NRS currently uses VentSim™ CONTROL, Ekahau Tracking and PI Datalink to control, monitor, and configure their VOD system."

Jan 1, 2019

By J. Bruce See

INTRODUCTION This symposium at Cu 2019 has been organised to honour and celebrate the career and achievements of Dr Phillip John Mackey, an internationally recognised expert in the production of non-ferrous metals, especially copper and nickel smelting and refining. Phillip was born in Epping, a suburb of Sydney, New South Wales, Australia on 19 April 1941 and is one of 4 children of Gilbert and Philomena (nee Bartlett) Mackey. After completing Primary School in Epping, he attended Marist Brothers High School in Eastwood, Sydney and graduated in 1957 as the Dux of the School. Phillip’s father, being on the staff of the Sydney Technical College, in Ultimo, Sydney had the opportunity in the early 1950s to meet the late Professor Sir Rupert Myers, Foundation Professor of the School of Metallurgy at the New South Wales University of Technology (later called the University of New South Wales or UNSW). Gilbert Mackey was impressed by the new young Professor of Metallurgy and encouraged his son to study metallurgy - at the time an expanding industry in post-war Australia. EDUCATION AT THE UNIVERSITY OF NEW SOUTH WALES Phillip commenced at UNSW in 1958, graduating with honours in 1963. His undergraduate education and training included a few years of part-time study while working at British Motor Corporation on sheet metal forming of car bodies. At University Phillip developed his talent for teamwork. He was a contributing writer to the University newspaper, Secretary of the UNSW Students’ Union and was active in the UNSW Metallurgical Society and co-editor in 1963 of “Metallurgical Review,” the annual journal of the UNSW Metallurgical Society. His diverse interests and curiosity about the world around him were likely nourished while at University. Upon completing his Bachelor’s degree, Phillip was awarded a Commonwealth of Australia Postgraduate Research Scholarship. He began his PhD in 1964 on the thesis topic “Studies in Heat Transfer between Dispersed Liquid Metals and Gaseous Atmospheres” working under the supervision of then Associate Professor Noel Warner, an outstanding Professor at the University. Professor Warner is now an Emeritus Professor at the University of Birmingham and is internationally respected for his pioneering theoretical and practical work on established and innovative smelting processes.

Jan 1, 2019

By Aleksandar N. Nikoloski, Tendekayi Tapera, Glen P. O’Malley

Chalcopyrite (CuFeS2) and enargite (Cu3AsS4) are among the most important copper sulfides. At present, many known deposits of these minerals are uneconomic to process because they are of too low grade, insufficient size or too remote to be cost effectively treated with conventional technologies that can deal with their refractory nature. Therefore, developing an effective, low cost extraction process for recovery of copper from them is important. The research presented in this paper will deal with potentially cost effective strategies involving catalysed processing, studied under conditions relevant to recycle heap leach conditions. The present account summarises some of the main findings from the research program carried out at Murdoch University between 2014 and 2018 that has investigated the effects of the common leaching parameters, major and minor species present in the leach system and additives on the rate and extent of copper extraction from low-grade ores, in which primary copper sulfide minerals such as chalcopyrite and enargite were the dominant copper minerals. The study involved batch leaching tests, detailed structural and mineralogical characterisation and thermochemical modelling under conditions relevant to heap leaching. The results have demonstrated that silver in particular has a strong catalysing effect on the extraction of copper from ore under the leach recycle conditions and, at an adequate dosage, can effectively overcome surface passivation, enabling almost complete extraction of copper from chalcopyrite as well as enargite. The aim of this paper is to present the effect of the studied additives and to briefly elaborate on the mechanism of the silver catalysed leaching process. In addition, the presence of certain secondary agents was shown to lower the critical dosage of silver and promote extraction. The data from the study allowed the development of a theory for the silver catalysed reaction mechanism, which enables further optimisation and cost-effective application of this strategy in practice. INTRODUCTION Researching the extraction of copper from chalcopyrite is important as it is the most abundant copper mineral in the earth’s crust. The majority of ores containing this mineral are processed by flotation to produce a concentrate, followed by smelting and electrorefining. However, most reserves available nowadays are of low grade or limited in size, and therefore not suitable for this conventional approach. Hydrometallurgical processing via heap leaching with or without the aid of bacteria has been shown to be potentially economical. Chalcopyrite is refractory though and suffers from slow leaching kinetics and poor overall extraction, so understanding the mechanism of how it leaches has received significant attention by researchers working in this field over the past 50 years. The refractoriness, which is the main issue with the hydrometallurgical approach, is generally described as passivation of the chalcopyrite surface whereby a surface coating is formed that blocks the reaction interface or wetting of the chalcopyrite, limiting the copper extraction. Exactly what this layer is made of or how the issue could be overcome has been the subject of intense study and debate for many years. One of the limitations of the work to date is that much of the research focus has been on typical initial leaching conditions, while there has been relatively little research into how the leaching is affected under recycle solution conditions where certain metal ions (Fe, Mg, Al) have often accumulated in the liquor. This occurs because the leach solution exiting a heap contains many species from the dissolution of gangue minerals and typically this solution is returned to irrigate the heap, once the copper has been removed, leading to an accumulation of these species.

Jan 1, 2019

By Osamu Inoue, Takashi Yamashita, Takashi Ikemoto

The expansion project in Naoshima smelter and refinery to meet enhancing recycling business of E-scrap was successfully completed in 2016 to have a capacity of 110,000 tpa of E-scrap treatment. Increasing treatment of E-scrap has raised the Ni content of copper anode to 4000 ppm on average, which is double the level of 10 years ago, and to 6000 ppm or more occasionally. The tank house has refined such copper anode to copper cathode with starter sheets. Since most Ni in Copper anode dissolves in copper electrolyte, the Ni content of the electrolyte has increased to 27 g/L and more. Ni accumulated in the electrolyte has increased power consumption during the electrolytic refining of copper, although cathode quality has been controlled satisfactory so far. In order to ensure sustainable operation while growing E- scrap business, the NiSO4 process has been expanded recently so as to recover Ni in the electrolyte more and the pressurized-leaching technology will be introduced to the slime leaching process so as to enhance the capacity of slime treatment and to improve Ni recovery in the near future. INTRODUCTION In recent years, the treatment amount of E-scrap at Naoshima smelter and refinery has increased according to the growth of its recycling business as shown in Figure 1, while impurities from E-scrap have concentrated in copper anode as well. Especially, Ni content in anode has been increasing remarkably since 2012, causing to raise Ni content in the electrolyte as shown in Figure 2. The increment of Ni content in copper anode and electrolyte has adversely affected the electrorefining process, slime leaching process, and NiSO4 crystallization process at the tank house. Such severe conditions provided opportunities to redesign the tank house to establish a robust process to which more Ni is acceptable.

Jan 1, 2019

By S. W. Henley

"Shaft sinking design is typically driven by what has been successful in the past and the availability of sinking plant. This document considers a project where the sinking design and methodology is unconstrained by conventional thinking and removed from the commonly held belief that a sinking methodology should be developed from available winding plant. Schedule was a key driver for the Project and led to an alternative sinking design that aimed to optimise sinking advance rates by specifying new winders that compliment known sinking plant while providing improved safety, redundancy and flexibility within each part of the sinking cycle. KEYWORDS Consistent, Efficient, Flexible, Improved, Innovative, Optimise, Redundancy, Safety, Schedule INTRODUCTION The project is remotely located in the South Gobi region of Mongolia on a brownfield site and the scope of work included the concurrent blind sinking and concrete lining of two (2) ventilation shafts to an approximate depth of 1,150 m at a finished diameter of 10 m and 11 m respectively. All sinking and lining operations to be completed as in-line activities, (no lining whilst other activities are undertaken). The project was schedule driven with a completion date set for the first quarter (calendar) of 2021 and there were no restrictions imposed on the successful Contractor with respect to their equipment selection. Existing sinking plant already onsite from three previous shaft sinking operations would be made available to the Contractor if required on an as is where is basis Sustained advance rates in excess of 2.4 m per day would be required in order to achieve the completion milestone, therefore the design would have to include contingency and demanded flexibility to account for equipment down time. Previous shafts that had been sunk onsite have utilised a single double drum kibble (bucket) winder (hoist) with a single excavator loading on the shaft floor into a large capacity kibble (bucket). DESIGN Mucking The sinking design centred on the mucking cycle given that this is traditionally the most restrictive part of the sinking cycle and typically accounts for one third of the overall sinking cycle. The Vertical Shaft Mucker (VSM) and/or diesel excavator are commonly used plant for shaft sinking that were under consideration. The use of Cactus Grabs was not considered given the higher risk associated with grab ropes and hoist failures."

Jan 1, 2019

By Gerardo Fuentes

Arsenic extraction from Chilean copper concentrates up to nearly 99% was achieved, using hydrothermal reactions. Arsenic appears in nature in more than 200 mineral species, being arsenopyrite (FeAsS), enargite (Cu3AsS4), and tennantite (Cu12As4S13) the most common species. In addition, arsenic is present in a large amount of copper concentrates, produced in northern Chile. Medical statistics show that in northern Chile, the amount of cancer to the lung, skin and bladder are the highest in the country. The latter situation, demonstrates the importance of studying metallurgical processes that do not generate atmospheric pollution. The hydrometallurgical processes such as hydrothermal treatment in autoclave reactors, do not produce gaseous emissions. On the other hand, the arsenic remains in solution from where it can be transformed in scorodite by widely known methods. Previous works about hydrothermal treatment of enargite have shown the feasibility of transforming the enargite of the copper concentrates into chalcocite or mineral species of the chalcocite family such as djurleite, digenite and for this reason enrich the concentrate in copper and pass the arsenic to solution. For this research, two Chilean copper concentrates were used, concentrate 1 with 5.5% arsenic and concentrate 3 with 1.8% arsenic. These concentrates were subjected to a complete chemical and mineralogical characterization. Later these concentrates were carry out to batch tests of hydrothermal treatment. Also, these concentrates were subjected to grinding to have different particle sizes. For the hydrothermal tests, a liter capacity Autoclave Engineer reactor was used. Characteristic of this reactor was the maximum temperature 350°C, 5000 PSI pressure, and 900 rpm agitation speed. Kinetic tests were carried out with the two concentrates maintaining the same solid: liquid relationship, the same agitation velocity and the variables studied were treatment temperature, time of reaction, concentration of copper in the solution and grain size of the concentrates. The conclusions of the study indicated arsenic extraction of the order of 93.98% from the concentrate 1 and arsenic extraction of the order of 98.74% from concentrate 3. After the hydrothermal treatment, the solids and solutions were characterized chemically, by electron microscopy and X ray diffraction. Also the solids were characterized by grainsize through a particle size analyzer (MICROTRAC). Results of batch treatment shows that arsenic can be release almost completely from real copper concentrates using this hydrothermal process and the next stage will be a scale up process in order obtain results for pilot plant design. INTRODUCTION Arsenic is an impurity that appears associated with copper minerals forming enargite, tennantite, tetrahedrite, and that due to the pyrometallurgical treatment either in conversion or roasting furnaces, it goes into the atmosphere together with the sulfur dioxide. A great quantity of literature can be found to eliminate arsenic or try to separate arsenic from copper. The methods used are mainly leaching processes with or without pressure (Padilla, Jerez & Ruiz, 2015) with different reagents like chloride media (Herreros, Fuentes, Quiroz & Viñals, 2003) or chloride media with sulphuric acid (Riveros & Dutrizac, 2008) or sodium hypochlorite (Mihajlovic, Strbac, Zivkovic, Kovacevic & Stehernik, 2007). It is known too that Chile is the first copper producer in the world and a great quantity of its minerals are in the north of the country, in Antofagasta.

Jan 1, 2019

By E. Nolasco, J. Ouellet, T. Tikka

"Shaft bottom structural systems are used in underground mining to support transfer of personnel, equipment and ore to and from underground to the surface. This paper first summarizes the evolution of design philosophy from a concrete tower supported on a concrete plug to the current structural steel design arrangement with unlined shaft walls, clear shaft bottom area with only a concrete housekeeping pad. Then the paper reviews the design parameters, analysis and design, and construction methodology for this rather unique shaft bottom structural system consisting of three sets of hitch beams, with each having specific functional requirements. INTRODUCTION Shaft bottom structural systems are used throughout the world in underground mining operations to provide a means to support the transfer of personnel, equipment, materials, ore and waste entering and exiting a vertical shaft ready for transport to and from the surface via the hoisting system. The shaft bottom structural system, for the Service Shaft (SS) at the Jansen Mine, is designed to accommodate two skips, a personnel/equipment cage, counterweight, services, loading pocket, rope changing, arrestor system, crash (or catch) beams, access platforms, stairs and rope divider system. Stantec and BHP have engineered a unique structural steel shaft bottom system for hoisting system at a Potash Mine. The shaft bottom structural system connects to a fixed guide and cantilever bunton system, used in the vertical shaft (shaft barrel), above the shaft bottom. The geometry for the shaft bottom structural system, shown in Figure 1 a), features three sets of hitch beams, beams which span across the shaft excavation or barrel. At the top of the structural system are two upper hitch beams. These hitch beams support a 64 metre suspended rectangular braced tower (upper tower), complete with steel guides for the conveyances. The upper tower passes through the main station (potash or mining) level and then connects to the top of the arrestor (lower) tower structure via a sliding vertical connection. The potash level is supported by two hitch beams spanning the shaft and loading pocket excavations. The arrestor tower, a braced compression tower structure, is carried by a third set of hitch beams. Below the third set of hitch beams is a short suspended tower complete with access platforms, stairs and the rope divider system."

Jan 1, 2019

By A. Abadías Llamas, N. Bartie, M. Stelter

Evaluating the economic viability as well as the sustainability of the Circular Economy (CE) system requires a deep understanding of the distribution of all elements, compounds, alloys, materials etc. in flows. In this paper, the circularity of the copper value chain, including primary and secondary processing, is rigorously evaluated. The studied system comprises the metallic copper production from primary sources (from mineral to metal), copper-containing commodity production (copper is mixed with other metals) and copper recycling through secondary smelting to close the loop. This is linked to photovoltaic (PV) panels and battery storage. A simulation model of this system is created using HSC Sim, considering more than 30 elements (and its various compounds), 180 unit operations and 800 flows. From the mass and energy balances obtained through the simulation, an exergy analysis is conducted to evaluate the resource consumption from a second law (entropy) perspective. Additionally, these results are complemented through a Life Cycle Assessment (LCA), the recovery of technology elements and by-products is discussed, while quantifying the losses through the value chain. Through the digitalization of the complete system, a better CAPEX and OPEX understanding of the metal recovery and losses can be obtained, as well as the associated resource consumption and environmental impacts. New flowsheets and technologies can be evaluated. Several scenarios show how the resource consumption and the environmental impacts are affected by the recovery of different materials to produce different products. INTRODUCTION A key challenge of the circular economy (CE) is the linkage and optimization of both resource and energy efficiency of the (renewable) energy infrastructure and the resource cycle depicted by Figure 1 simultaneously. In addition, the CE requires the linkage of all stakeholders as shown by Figure 1. This has been discussed in some detail by Reuter and Bartie (2019) and Reuter et al. (2019). Copper and all its associated technology elements is one of the key enabling metals that is an economical copper colored thread through CE society (Reuter & Kojo, 2014). The Metal Wheel (Figure 2) shows the linkage of and recovery of various elements associated with copper and other carrier metals. This reveals that copper acts as an important carrier metal because of its properties i.e. the wealth of technology elements it carries from geological ores, but also its capacity to act as solvent of valuable elements and thence a key closer of various complexly connected element and material cycles when these technology elements are released during copper refining. The same applies to all other carrier metals of modern CE society as shown for example recently in a lead policy brief (Blanpain, Reuter & Malfliet, 2019).

Jan 1, 2019

By Greg Wyartt

Although electronic detonators and blast initiation systems have been commercially available for several decades, uptake in the Australian mining industry has been very slow when compared to other global mining regions. The safety and operational advantages of electronic initiation are generally well understood in Australia, however there has been a prevailing perception that these advantages do not outweigh the extra financial and technical investments.

Jan 1, 2019

By A. Torrance, M. G. Seo

Velocity of detonation (VOD) is an important variable when evaluating the performance of mine blasts. Typically, for a VOD measurement, individual probes have to be loaded into each blast hole that requires a measurement, which increases the loading time and is not representative of the whole blast. Experimental studies of electromagnetic pulse (EMP) from the detonation of explosive charges show that electric and magnetic field signals are observed when chemical explosions occur in the air, at the ground surface, and in the underground. EMP has the potential to evaluate VOD of the whole blast without impeding the loading process. Due to a variety of physical causes which make the electromagnetic effects complex, measuring EMP of the detonation of explosive charges has not been fully studied yet. Five different antennae were tested with explosives, which are commonly used in mining industry. Among the five antennae, aluminum and copper tape, and wire were successful to detect the EMP. INTRODUCTION The measurement of the velocity of detonation (VOD) helps in evaluating and comparing relative performance of explosives in mine blasts. A VOD of an explosive is usually predicted by empirical mathematical equations or measured in-hole by VOD meters. However, conventional methods to measure a VOD have constraints: only a limited number of holes can be measured because cost of consumables for such systems is very high, and systems only allow a certain number of holes to be measured. The measurement cables have to be placed into the holes prior to loading with explosives which means that preparing to take the measurement is time consuming and has to be well coordinated with the mine. In order to evaluate VOD for a whole blast, there is a possibility of using electromagnetic pulse (EMP) from the detonation of the explosives. As there are many parameters that affect the generated EMP from explosive charges, measuring EMP of the detonation of explosive charges has not been fully studied yet. Most studies conducted relate to military related explosives, not the ones frequently used in mining industry. This research has been performed to have a better understanding of EMP from the types of explosives which are commonly used in the mining industry. To discover a way to detect EMP efficiently, five different types of antennae have been studied in the air and in the underground blasting conditions: coil, monopole rod, log periodic, wire, and aluminum and copper tape. LITERATURE REVIEW Conventional methods of measuring VOD Over the years, demands for more accurate theoretical predictions and physical measurements of the effects of the explosives have increased. Especially when both demand and commodity price decline, mining companies are keen to understand the effectiveness of explosives since it has a direct relationship with fragmentation, which influences their production rate. Since the 1940s, various methods have been devised to determine VOD of explosives.

Jan 1, 2019

By R. Grau

"After commissioning and start-up of the first 500m3 TankCell® flotation cell in 2014, the over 300m3 mechanical flotation cells have earned their place in large-scale flotation operations. These 500 to 630m3 cells, designed for projects with large throughputs, are proven to provide savings in project capital and operational expenditure through savings in foot print, energy consumption, and less equipment to install and maintain. Addition to savings in different phases of a project, these cells provides operational flexibility and has shown improvements in metallurgical performance. In this paper a case study from Kevitsa TankCell® e500 installation and Buenavista del Cobre TankCell® e630 installations will be given.INTRODUCTION After development (Grönstrand and Bourke, 2008), characterization (Morales et al. 2009; Yanez et al. 2009; Grönstrand at al. 2009), validation (Elgueta et al. 2009; Coleman and Dixon, 2010), and more than 350 industrial installations of the Outotec TankCell® e300 flotation cell, the well proven energy efficient TankCell® product family introduced the TankCell® e500 forced-air flotation cell late June 2012 (Outotec.com, 2012). The introduction of the 500 m3 flotation cell followed by introduction of a 630 m3 flotation cell, TankCell® e630, in October 2014 (Outotec.com, 2014). These large flotation cells are designed for projects with high throughputs where the number of cells needed for operation with smaller equipment would become large. The benefits of this size of flotation cells comes from the lower capital expenditures due to lower equipment costs, savings in plant footprint, less installation work with less auxiliary equipment, lower energy consumption, and less units per installation resulting in less components, spare parts and maintenance.The first TankCell® e500 was commissioned and taken into operation in October 2014 at FQML Kevitsa Cu-Ni-PGE concentrator, nowadays owned by New Boliden. The first TankCell e630 was taken into operation in January 2018 at GrupoMexico’s Buenavista del Cobre Cu-Mo concentrator. The start-ups of the first TankCell® e500 and TankCell® e630 followed with test work where the hydrodynamic performances of the cells were characterized and metallurgical performance studied. The results of the TankCell® e500 test work were presented in detail by Mattsson et al (2015a; 2015b) and TankCell® e630 by Grau et al. 2018. In this paper the metallurgical improvements achieved with the large cell installations will be presented."

Jan 1, 2019

By Bing Li, Kai Liu, Yongcheng. Zhao

With the ongoing development of copper smelting technology, the improvement of environmental emission control and achieving an automated continuous copper pyrometallurgical process have become the key development goals for copper smelting. The double bottom blowing continuous copper smelting process combine bottom blowing smelting (SKS) and bottom blowing converting (BCC) process and fire refining as “three-connected furnaces” arrangement is a pyrometallurgical process independently developed by China’s ENFI which can continuously produce copper from raw material through to anodes. This technology can improve energy efficiency and reduce environmental emissions for the overall copper smelting and converting process. This paper discusses the engineering characteristics and production practice of the SDIC Jincheng Metallurgical Project, which operates SKS smelting and BCC converting process with “three-connected furnace” arrangement for the first time in the world. Advanced engineering concepts and tools were used to optimize the configuration during the project engineering stage. The operation shows that the process has good environmental performance, reduced energy consumption and high level of automation, which is a new choice for copper continuous smelting process. INTRODUCTION One of the most important developing trends for the overall copper smelting process is to develop a continuous operation. Continuous copper smelting can maximise energy efficiency in copper concentrate and make full use of the rich heat treatment system. Cold charge and a part of low-heat-generating materials, which are processing with additional equipment in traditional copper smelting process, can be processed with rich reaction heat in continuous copper smelting and converting process to achieve good economic benefits. Yuan and Wang (2017) noted that SKS+BCC copper smelting process can reduce the secondary SO2 emissions compared with discontinuous copper smelting process, which required transportation of melted matte by matte ladle and may cause secondary pollution. The continuous copper smelting process can also reduce the generation of intermediate cold materials.

Jan 1, 2019

By Fulian He, Jianhang Chen, Shoubao Zhang

"Fully grouted rock bolts have been used in mining industry for many years. Significant research has been conducted to evaluate the load transfer behavior of fully grouted rock bolts with experimental programs. However, compared with that, less work has been conducted with analytical modelling. Therefore, in this paper, the authors used an analytical model to study the load transfer behavior of fully grouted rock bolts. To confirm the credibility of this analytical model, an in-situ pull-out test was used to validate this model. There was a close match between the experimental result and the analytical result. Following this, a parametric study was conducted with this analytical model. The influence of coefficients, Young’s modulus of the rock bolt and the diameter of the rock bolt on the load transfer performance of rock bolts were studied. Furthermore, the load distribution along the fully grouted rock bolt was analytically studied. The results show that the axial load in the rock bolt decayed from the loaded end to the free end independent of the pull-out load. However, the trend of the load distribution curve was influenced by the pull-out load. This paper was beneficial to better understand the load transfer mechanism of fully grouted rock bolts.INTRODUCTIONRock bolts have been used in the mining industry for a long time. They are used as the reinforcement tendons to keep the stability of openings in underground mining and the slope in open-pit mining. Furthermore, rock bolts are commonly used not only in the mining engineering, but also in civil engineering (Thompson, Villaescusa, and Windsor, 2012).The rock bolt is a tendon which can be a rod or a cable inserted into a borehole drilled in rock masses or soils. Traditionally, the material of rock bolts was steel. However, engineering practices showed that the steel rock bolts can be easily corroded by the moist environment in underground mines. Next, Fiber Reinforced Polymer (FRP) was used to manufacture rock bolts, which are termed as FRP rock bolts. Experimental results proved that the FRP rock bolts can effectively reinforce the surrounding rock masses without being corroded (Wang et al., 2018)."

Jan 1, 2019

"Yara Siilinjärvi in Finland is the Western Europe's only apatite mine. Annually it produces one million tons of apatite concentrate, which creates 10 million tons of tailings. At the beginning of 2017, Yara replaced their conventional TSF with a new tailings treatment plant, which increased the solids content of the slurry from 45–48% to 66–68%, making it possible to deposit as a paste. This extended the life-span of the current TSF from 2020 to 2035. This paper presents the storyline of the Yara paste plant project. The project began with laboratory testing and then progressed to pilot-scale thickening and beaching trials. After successful pilot trials, the final process design was implemented. Process automation played a key role in the project. An advanced control system is needed to maintain process stability and the desired operation point in various operational circumstances. Since commissioning the paste plant has been running consistently with an underflow solids content of 66-68%, with average beach slope angles of 3.5 degrees in the tailings disposal area. Robust thickener operation also leads to the trouble-free high-density pumping and high availability of the plan. During first year of operation the plant’s availability has been very good, over 97%, and currently, the plant is operated remotely from the main concentrator plant.INTRODUCTION The Yara Siilinjärvi Plant is owned by Yara International, a Norwegian fertiliser company. Yara Siilinjärvi is Western Europe's only apatite mine, and it primarily produces apatite concentrate for its Siilinjärvi phosphoric acid plant. A portion of the concentrate is also dried and shipped to other Yara fertiliser plants. The site annually produces one million tons of apatite concentrate, which creates approximately 10 million tons of tailings. Extending the lifespan of the 1150-hectare tailings storage facility has been studied in Siilinjärvi for a long time. The aim has been to use the same tailings area footprint, without any new land purchases or major dam increases. An important part of the process has been to study the possibilities for using new technologies, especially thickened tailings technology (Ruhanen, 2014)."

Jan 1, 2019

By Stephen C. Tadolini, Colton Cook, Cody Hildreth, Frederick Cybulski

"Broken and jointed ground is extremely hazardous and requires unique stabilization techniques to protect worker and critical entries. Bolting techniques, even the most advanced with pre-load to create roof compression, can leave large gaps of unconfined and separated roof. This roof can also be susceptible to water inflows which only exacerbate the support problem. These types of conditions existed on long term development main entry accessing several future longwall panels. The geotechnical assessment identified well-defined jointing systems that also permitted water to flow between the roof separations, which “lubricated” the roof material and minimized any frictional advantages. Chemical injection of a Polyurethane material, Minova Carbopur WS, was placed beyond the bolted horizon to move the water to the rib lines and reinforce the fractured and broken roof. The injection material permitted the effective use of bolting patterns and helped ensure long-term stability of these critical entries. The paper describes the evaluation techniques, design patterns, basis for chemical selection and application, and results and recommendations.BACKGROUNDThe injection of mine and underground civil structures using polyurethane (PUR) has been ongoing for over 50 years. The applications in mining have included gate road stabilizations, longwall set-up and tear-down entries, and simple consolidation of coal mine roofs. PURs have also been used for roof stabilization during longwall shield recoveries. Polyurethane injection was initially developed by the Bergbau-Forshung GmbH, a German coal mine research institute, in the early 1960s (Jankowski, 1972). The product became a standard stabilization method in Germany after its commercial introduction in 1971 (Knoblauch, 1994), and was successfully manufactured at the Minova Essen, Germany location for over 50 years. With the recent closing of the German underground mines, that manufacturing facility has been closed and moved to Katowice, Poland, where production continues today Injection products are also being successfully manufactured by Minova in Australia and the United States.Polyurethane injection in underground coal mines is used in difficult ground conditions in fractured immediate and main roofs. It is also common as a rock stabilization remedy to prevent longwall face caving during shield removal. As presented in the case study, polyurethane was applied to minimize the inflow of water from beneath a stream channel while providing reinforcement and consolidation of the fractured roof that had lost confinement. Polyurethane is a two-component system (Part A and Part B) that is injected into a borehole and can chemically bond to the rock, not relying on friction or mechanical interlock to provide support. The material is injected under pressure, coupled with a low viscosity and small particle size; it flows into roof fractures and separations, which are the paths of least resistance. New developments in low viscosity PUR materials allows penetration of cracks as tight as 0.002 inch (0.05 mm) wide. This also allows for the closures of extremely small cracks to minimize the inflow of water, even if the water is under pressure. Combinations of designed expansion properties and low viscosities make the materials ideal for minimizing and stopping flows of water from underground structures."

Jan 1, 2019

By J. K. Armstrong, C. Feyerabend

"As mines are constantly growing and expanding, so do the challenges for emergency response teams. They have to keep up with the pace set by current and future production techniques. Although mines have now reached depths of several kilometres and their dimensions and complexity are that of an entire city, mines rescue still must be able to reach the most remote areas within the mine in a swift and safe manner. The duration of breathing apparatus and physical human capabilities are limitations. Therefore, alternative methods have to be explored to extend the time under oxygen for mine rescue teams without putting additional stress on the team members. To address this global trend, Dräger, Goldcorp and PAUS have partnered to develop a mine rescue vehicle that allows mine rescue teams to travel for an extended period of time through a contaminated atmosphere without the use of breathing apparatus, thus extending the range of their mission. By applying currently available techniques, the safe expansion of mine production can be ensured, giving mine rescue teams the ability to respond to accidents in a safer and faster way. INTRODUCTION With the reduction of easily accessible natural resources, there is a global trend toward searching for higher ore grades underground and/or continually expanding mines underground to extend their lifetime. While in some areas this trend has just begun, in other countries mines are reaching depths or horizontal dimensions that pose extreme challenges (Codelco, 2016). These challenges include safety relevant topics, such as rock stability, heat and seismicity, but also more basic issues such as distances to the working face, which can become crucial considering the cost to develop a new shaft or decline. To overcome this, there is a growing interest in collaboration among various stakeholders to drive the development and support of deeper mines and tackle the complexity of underground mining. This is evidenced by the fact that several industry and research groups and networks have formed, e.g. the I2mine project in Europe and the Ultra-Deep Mining Network by the Centre for Excellence in Mining Innovation in Canada. Due to commodity pricing and the trend toward renewable energy, metal/non-metal mining will be the driving force behind this development."

Jan 1, 2019

By F. Prescott, D. Hiam-Galvez, J. Hiam

Mines are frequently located in remote areas with little conventional employment and few opportunities for the existing population. The development and operation of the mines results in several years of intense activity followed by a near-complete reduction in employment and opportunities after the mines are closed. Designing Sustainable Prosperity (DSP) is a method for rectifying this situation by designing for long-term growth in areas that host mines. This process involves the participation of local and national governments, local community, mining companies, investors, academics and those with sector expertise. The mines will be the catalyst for regional sustainable development. If successful, long-term economic and environmental prosperity should be the result for the areas affected by mining and, in some instances, promoting the regions as centres of excellence for a particular industry. This paper will describe how the concept works using the copper producing region of Peru and Chile as an example. Designing sustainable prosperity starts by looking at regions based on the natural resources and skills available, the infrastructure and possible energy sources. Integrated natural resource models and innovative market studies, followed by education and skills requirements, are then established to determine the potential for the region and what needs to be done to realise the possibilities. INTRODUCTION Industry 4.0, or i4.0, dubs the fourth and current industrial revolution. Where previously they have been founded on ever-increasing consumption and production, i4.0 distinguishes itself by its partial focus on reducing resource intensity; lightweighting, energy efficiency, sensors and automation to improve resource efficiency. Industry 4.0 is an era of artificial intelligence, genome editing, biometrics, renewable energy, 3D printing, autonomous vehicles and the Internet of Things (Lu, 2017). These drivers represent key opportunities for the economic future of nations and regions.

Jan 1, 2019

By L. Iacopetti, A. Calderara, M. Perego, P. Perrone, T. Furusawa

De Nora, a global leader in the development, manufacture and sale of all DSA® anodes based on titanium coated with mixed metal oxide (MMO) for electrochemical processes will present key advancements made to Self-Protected Anodes (SPA) for metal electrowinning. (DSA® is a registered trademark of Industrie De Nora S.p.A., Italy). In 2017 pre-commercial demonstration cells were operated in industrial environment. The program’s focus was to fully demonstrate the SPA anode’s superior mechanical and electrochemical robustness during normal and induced dendrite shorting occurrences while providing quality of plating in commercial operation. De Nora specialists focus on key components, in particular the engineering of the self-protection system, DSA® anodes and catalyst formulation capable to cope with high levels of pollutants while providing long service life in the meantime. Results of field trials confirmed the expected anode performance and enabled the selection of the most suitable “SPA” structure, based on resistive protective elements. Summarizing the economic benefits to copper electrowinning tankhouse operation with De Nora’s self- protected all DSA® anodes are; Double-digits power savings Cobalt-free electrolyte operations Minimal dendrite shorting damage incurred at the SPA anode Smoother, uniform cathode deposits with tangible improvement on current efficiency Tankhouse operations producing lead-free copper quality cathodes, in addition to elimination of lead waste for improved operator health and environment. INTRODUCTION De Nora’s engineered “Value Technology Package” (“VTP”) for electrowinning, consisting of our DSA® anodes coated with mixed metal oxide specifically formulated for copper electrowinning in conjunction with an advanced self-protected full titanium anode (“SPA”), underwent an intense field qualification program, inclusive of the behavior under massive short-circuits as part of the field investigation, with the goal to select and appoint the ultimate design configuration of “SPA”. Optimized wireless-based monitoring system was included in the field program, demonstrating good functionality for cell parameters monitoring and remote shorts detection.

Jan 1, 2019

By L. Hanschar, C. Bwalya, E. Mokola, K. Musonda, A. Makayi

This paper describes the installation, commissioning and operation of porous plugs featuring nitrogen gas purging in both Anode Furnaces at the Kansanshi Copper Smelter (KCS), a greenfield copper smelter which commenced operation in March 2015. The decision to install porous plugs was taken in November 2016 and the facilities were successfully commissioned on both anode furnaces in October 2017. The project was successful and has demonstrated the following process improvements: 12.2% reduction in main burner fuel consumption Larger average charge size, due to fewer accretions; 17 minute decrease in average refining cycle times Improvements in slag skimming operations Improved casting rates INTRODUCTION Porous plugs The application of porous plug technology in copper smelter anode furnaces is well established around the world. Vukovic and Gamweger (2017) and Wallner (2004) noted that the stirring and mixing action induced by the injection of inert nitrogen gas into the molten copper via porous plugs has potential benefits in the following areas: Homogenization of the temperature and composition of the molten copper resulting in Reduced fuel consumption Less tendency to overheat slag (reduced risk of refractory attack) Less slag produced with a lower degree of oxidation (lower rate of refractory wear) Less tendency for buildups to form Improved environmental performance (produce low sulphur blister at Peirce Smith converters) Elimination of buildups inside the furnace and potential for larger charges per cycle Reduced processing times and potential for shorter cycle times More efficient skimming of anode slag Shorter skimming time Less copper carry over to Peirce Smith converters Very little slag remaining in the furnace (reduced potential for buildups to form)

Jan 1, 2019