Search Documents

An Integrated Solid Waste Management Method for Western Macedonia, Greece

Sep 13, 2010

Project cost control procedures and computer systems have enjoyed a successful and simple relationship over the past decade, thanks primarily to the proliferation of portable computers or PC's. Prior to the introduction of this technology, project control was largely a manual and somewhat onerous task of historical data compilations, with little time available for dynamic forecasting, staged planning, or pre-emptive cost control. Automated systems developed during this era were resident on "Heavy Iron" or mainframe computers and were expensive to maintain and operate. Use of these early systems was limited to large engineering, construction, and industrial concerns with the economies of scale and funding required for their successful application. Systems were either designed for critical path analysis or task scheduling, but rarely integrated with the other, much less cost control.

Jan 1, 1990

By Ian F. Hughes

"Concepts of an integrated steel plant for sheet products to be built and operating in the year 2000 will be described. The design and operating methodology of this market driven facility will integrate process uniqueness, standardization, manufacturing automation, artificial intelligence and information flow.An integrated steel plant for the year 2000 is defined for this article as one that will be built on a greenfield site and ""started up"" in the year 2000 with a capacity of three million tons per year of flat rolled products ranging from cold rolled and electrical steels to high strength formable steels and a full range of coated products.It may seem that the 21st century and the steel plant we're discussing are far into the future. The startling truth, however, is quite the opposite. As shown in Figure 1, even with accelerated development, a new process on which laboratory development work is begun today might just barely pass through the laboratory phase, pilot plant, and commercial feasibility stages such that it can be considered viable for construction and start up in the year 2000.On that basis, it is very unlikely that this 21st century steel plant will utilize any technology that isn't at least under investigation in the laboratory in 1988. As a result, we recognize that planning and selecting the facilities for this plant is, in fact, a pragmatic rather than futuristic process, and that its main value is in providing a bridge to longer-term predictions."

Jan 1, 1988

By Yong Li, Tao Jiang, Xiangxin Xue, He Yang

"In this paper, we describe the current status and research progress on the utilization of typical industrial solid wastes in China. We propose a creative method called “eco-utilizing wastes” with an aim of both integration and increment but without second-time waste and pollution, in terms of the characteristics of typical industrial solid wastes, such as titanium-bearing blast furnace slag, high-silicon iron tailing and boron-enriched slag as well as oil shale.Situation of Typical Industrial Solid Wastes in ChinaThough mineral resources in China are abundant, most of these are low grade ores. Moreover, the distribution of mineral resources is asymmetric, which causes the increase of cost and decrease of the economic benefit. Over-exploitation of mineral resources results in a large number of solid wastes. The accumulation of solid wastes not only means the waste of valuable resources, but also causes environment deterioration. There exist some problems in the current practice of the disposal of industrial solid waste, such as only emphasizing the final results and causing new pollution and waste [1]. So the research and development of a high value-added method has a high practical relevance to our nation. Based on the present status and research progress of industrial solid wastes in China, a creative new idea and method for eco-utilization of solid wastes is proposed in this paper."

Jan 1, 2012

An Integrated Study of Bubble-Particle Attachment Mechanisms

Sep 13, 2010

By C. L. Sainsbury

For 10 years, the author has been engaged in a program of geologic mapping of the Seward Peninsula, Alaska, for the U.S. Geological Survey. Initially, two 1:63,360-scale quadrangles were napped by traditional methods of traverses by foot and by tracked vehicle, supplemented by reconnaissance from a light aircraft owned and piloted by the author. Five summers were required to map those two quadrangles, which lie north of the tree lice in typical Arctic climate. In 1967, the project was reoriented toward the reconnaissance capping of four 1:250,000-scale quadrangles, with helicopter support to be used for cart of each of four summers amounting to about 45 hours time per support year. The light aircraft was use-,' to support the field operations. Over the year,, the aircraft was used in progressively more geologic tasks, culminating in 1970 with a successful field test of rudimentary devices made to collect soil, rock, and sediment samples while the aircraft remained airborne. Additionally, an attempt was made j- 1970 to prepare reconnaissance geologic maps entirely by the use of the light aircraft combined with foot traverses [fr??], the landed aircraft. Several such maps, prepared at the rate of about one 1:63,360-scale quadrangle per day, were checked from a helicopter by an impartial observer end were found to be sufficiently accurate for reconnaissance mapping when reduced to 1:250.000 scale.

Jan 1, 1971

By P. Rocque, S. Talebi

Although the measurement of blast vibration close to the blasthole is critical to the understanding of rock fragmentation mechanisms and blast damage in the rock masses, limited experience for such monitoring exists. Because much higher vibration amplitude and frequency ranges are expected in rock masses close to an explosive charge as compared to far field vibrations, different problems from those for the far field monitoring must be considered for near field blast vibration monitoring. Currently, guidelines for design of the near field blast monitoring systems do not exist. This paper describes the development of an integrated technique for vibration monitoring close to a blast hole, including selection and installation of transducers, design of a monitoring system and signal recording. A densified cement was designed for grouting accelerometers in order to match p-wave impedance between the rock and grout. The monitoring technique described has proven suitable for blast vibration monitoring within 2 m to 15 m of a blast hole having loading conditions similar to production blasts.

Jan 1, 1993

By C Parihar, R Garg, A Bhandari, S Bhandari

Blasting can impact the efficiency of entire downstream mining operation. Individual technology solutions for blasting have been available in the industry for many years but all of them only cater for certain aspects of blasting. Many of them are based on individual research and/or experiences. Some of the available software solutions are not suitable to be used in the field as that they need advanced skills or tools. Also, most do not take technology advancements like mobility, advanced data analytics, web solutions and integration into consideration. Hence, no technology platform is currently present in the industry that addresses all potential needs a blaster may need in an integrated manner.This paper presents an integrated solution that takes care of all aspects of blasting – design blasts according to mine plan; collect data after drilling has been carried out (as there is often difference in designed and actual drilled hole locations in the field); predict blast results in terms of fragmentation, flyrock, ground and air vibrations, wave front reinforcement and flyrock distance; and after assessment, allows changes in charging, delay timing and sequence. The technology solution is a secure, cloud-hosted, web-based software-as-a-service solution that can be accessed from anywhere. Also it has a mobile app, which is available for both Android and iPhone/iPad. The mobile app is also integrated with the web-based solution using application programming interface calls to the central data repository.Case studies for two limestone mines are presented where this solution is being used in its initial format. This software platform enabled analysis of the outcome from a previous blast pattern and then subsequently allowed optimisation of blasting operations based on historical data. Uses of this platform have resulted in improved key performance indicators in these two limestone mines. The mobile app as part of this platform enables extensive field blast data capture and analysis and also various predictions before a blast. Data collected include blast parameters, individual hole charging, initiation pattern, videos, photographs and vibration records for analysis/reporting. The key features of the solution are a blast designer, a detailed blast data collection/analysis and a series of environmental predictors. These predictors give blast results in terms of fragmentation, flyrock, ground and air vibrations and wave front reinforcement and take remedial steps before blasting to optimise and control adverse environmental impact. Many features, such as fragmentation predictor and mobility solution, are completely unique features that are not available elsewhere in such a field personnel-friendly manner.CITATION:Bhandari, S, Parihar, C, Garg, R and Bhandari, A, 2015. An integrated technology solution for optimised and environmentally-controlled blasts, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 393–400 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Leroy G. Hagenbuch

"IntroductionAn integrated Truck Management Information System (Truck MIS) evolves as seemingly separate functions combined to yield a single homogeneous result / product. The concept of a computer integrated Truck MIS includes truck dispatch, truck maintenance management and truck weighing.A truck management system is only as good as the information / data bases input to it. The concept of an integrated system works best with automated data gathering. Automated data gathering provides timely and normally, the most accurate historical information/data bases. Data bases are, however, historical, which is a problem to be overcome in a computerized truck management information system, especially in regards to a truck dispatch system as loading sites / loading conditions and some dump site conditions continually change. As these changes occur, data base s must change as well, and thus the need for the continual update of data bases that the computer uses for a Truck MIS.For a truck dispatch system to achieve reliability / viability, dispatch decisions need to revolve around real time data gathered in an automated way. Integration of all truck management function s through automated data gathering lead s to the best over-all system.An integrated system is a combination of many different factors and is only as good as each factor / building block put in the system. With the proper building blocks, an integrated Truck MIS is very feasible - an MIS System that includes weighing, time and motion study, truck maintenance and maintenance management, as well as truck dispatch.Truck MISAn integrated Truck MIS provides for truck dispatch as the ultimate end result, a truly automated /integrated truck dispatch system (to function non-operator-dependent). The following comprises its central building blocks:-Time.- Haul Cycle Segments.Truck Status, i.e. Load on truck,- being loaded,- loaded,- unloaded,- in service,- out of service.- Vehicle Location.Loading Equipment Status.- in service,- out of service.Optional- distance travelled in each haul segment.With this data provided on a non-operator dependent basis, it is possible to build good data bases so a computer can make truck dispatch decisions. Knowing what information is needed as the central core to a good Truck MIS, how can this information be automatically gathered and fed into a central control computer?"

Jan 1, 1986

By Barber S

The Golden Cross Mine is located within the Waitekauri Valley near the southern end of the Coromandel Ranges, eight kilometres north-west of Waihi, North Island, New Zealand. The mine is owned and operated in a joint venture by Coeur Gold NZ Ltd (80 per cent) and Viking Mining Ltd (20 per cent). The underground mine produces gold and silver from low sulphidation epithermal quartz veins which developed in the shallow parts of a meteoric water dominated system during the Upper Miocene (7.36 - 6.67 Ma). The Empire Vein System is hosted within a dilational structural environment which developed at the lithological contact between acid intrusives, rhyolitic-dacitic tuffs and reworked pyroclastics, and undifferentiated andesites. The formation of the Empire Vein System was controlled by the rheological properties of the host rocks and variable displacement along a series of normal, right lateral, easterly-dipping faults. These faults represent sub-parallel zones of master shearing within a Riedel shear model. Underground mining extracts ore from the steeply dipping hangingwall and the complex footwall veins of the Empire Vein System. Initially sills are driven along the hangingwall vein on ten to fifteen metre sublevel intervals. In the footwall zones where significant mineralisation adjacent to the hangingwall sill drives has been identified, a series of cross-cuts and footwall drives (sub-parallel to the hangingwall sill) are also developed. Where continuity of mineralisation and ground conditions permit a combination of post pillar flatbacking and AVOCA longhole benching methods are used. Detailed underground mapping of lithology, quartz veining and major structures provides the information for designing ground support and footwall pillars, planning mine development and ore extraction sequencing. Sectional interpretation displays the vertical extent of faults, fractures and the vein system. The mining methods used underground at the mine have evolved through a thorough understanding of the structural complexity and the systematic geological mapping of the Empire Vein System.

Jan 1, 1997

By I. Sanchez

The development of the recent generation of large mining projects in South America has been challenging in many ways, but especially in the management of water in all its aspects. As a result, a number of projects have experienced difficulties and in some cases significant delays due to a lack of a clear and approved definition of the supply, use and discharge of water from mining and processing sites. The development of the recent generation of large mining projects in South America has been challenging in many ways, but especially in the management of water in all its aspects. As a result, a number of projects have experienced difficulties and in some cases significant delays due to a lack of a clear and approved definition of the supply, use and discharge of water from mining and processing sites.

Feb 23, 2014

Oil sands processing generates huge volumes of slurry, known as tailings, that is being stored in tailings ponds. The volume of produced tailings is a very important factor in oil sands surface mine planning, because the available area for dam construction is limited to the lease areas. On the other hand, oil sands operators cannot leave mine sites without reclaiming the tailings ponds. Since most of the reclamation material is generated in either oil sands mining or processing, it is reasonable to include reclamation material requirement as part of long-term mine planning. In this paper, an integrated optimization framework is proposed to maximize the net present value (NPV) of the produced oil sands, with respect to tailings capacity constraints and reclamation material requirements. A mixed integer linear programming (MILP) model is developed to find the optimal solution for long-term mine planning problem. A sample bitumen processing flow sheet is used to formulate the volume of produced tailings, based on Clark hot water extraction method. To verify the proposed model, it is coded in Matlab and run using CPLEX. Run results for real-case oil sands dataset show that the optimal production schedule meets material requirements for reclamation, tailings volume is within tailings capacity range in all periods and the production schedule follows the predetermined horizontal direction.

Feb 27, 2013

By F D Durao, Muge F. H, Rogado J. Q

In the scope of the project named CAPUME II (EEC BRITE/EURAM contract - project MA2M-CT90,-0042(SMA)) for the development of an integrated mine planning system for underground mines, two of the main tasks were the development of a short-term mining planning procedure (module) and a numerical simulator of the mineral processing plant of Pirites Alentejanas - PA. The short-term mining planning module defines the mining sequences by solving a constrained minimisation problem. The ore grade variability is the objective function subject to the geometrical constraints of the mining method and to the maximum of `internal blending'. The optimisation problem is solved by applying a dynamic programming algorithm. The plant simulator is an essential tool of the planning system allowing the preview of metal grades/recoveries of copper, lead and zinc of concentrates streams, given the corresponding metal assays of the run-of-mine ore, defined by the short-term mine planning module. This way, the management can plan the short-term mining operations (the weekly sequence of exploration blocks and the internal planning) in order to fulfill given required conditions, based on a shipment schedule and on a purchaser's formula. In this paper, after a short description of the short-term mining planning module and of the simulation package named SIMUL, a synthesis of the main model development steps and the results of some simulation runs are presented and discussed.

Jan 1, 1995

By Hutchinson IN

In order for the Australian underground coal mining industry to achieve the high productivity rates demanded of it without compromising its good safety record, improved geotechnical monitoring systems are required. One of the main problem areas affecting underground coal mining is the deterioration of previously stable roadways.CSIRO Division of Geomechanics has been working on a NERDDC funded project to develop an instrument to monitor coal mine roof deformation. The instrument which has been developed, Roof Alert, is a self contained, battery powered, intrinsically safe device. It can monitor the magnitude and rate of deformation and give multiple, variable visual alarm signals where preset levels ate exceeded.

Jan 1, 1991

By M. A. Nadar

Harsh and dynamic construction sites are generally equipped with cranes in order to rapidly and conveniently move heavy loads from one location to the other. If not properly inspected and managed, this operation can be very hazardous and lead to accidents. As such, a reliable and self-contained monitoring system that can update construction and safety personnel about the status of the crane, the weight of the load lifted, the location of the boom with respect to nearby buildings and other tower cranes, and the weather conditions under which the crane is operating, is deemed necessary. This can lead to significant time and cost savings as well as safety and productivity improvement due to the accuracy and immediacy of relevant on-site crane information delivery. This paper takes the initial steps and presents research targeted at evaluating the capability of wireless sensor networks (WSN) for monitoring tower crane operations in construction environments. A reliable long range WSN system is implemented and information is obtained from various special-purpose sensors (temperature, wind, proximity, etc.) mounted on special motes that relay data to and from each other and a central hub. The latter continuously monitors and manages network performance and relays incoming data to the host application. This application, in turn, displays the received data, and maps it onto a user-friendly visualization scheme, triggering alarms when a set of pre-programmed rules and safety conditions are crossed. The components of the proposed system have been tested through proof of concept experiments and preliminary results highlighted the potential of WSN systems for improving monitoring of tower cranes and reducing related accidents on construction sites, especially in Lebanon and the Middle East region where safety precautions are usually not properly implemented.

Aug 1, 2013

By K. Kasas, J Kermeci, S. Vujic, S. Secei, P. Kermeci

On the ‘Majdan III’ open pit mine, supplying with brick clays the production plants of the industry of building material ‘Potisje-Kanjiza’ from Kanjiza, a modern ECS (excavator-conveyor-spreader) complex was built, integrating four bucket excavators, six conveyors and one spreader into a whole. This complex connects the mineral-exploitation unit with the final brick-products plant of the company. Monitoring and management of the ECS complex is carried out by modern computer-supported information-management system (IMS) implementing most modern measuring-regulation, computer and GPS equipment. It was concluded that, for safety reasons, the functions of the IMS should be developed by a component of active visual monitoring of the ECS complex. For this purpose, the task of making a project on intelligent system for visual monitoring of the ECS complex was entrusted to the Department of Computer Application at the Faculty of Mining and Geology, University of Belgrade. This paper gives a review of basic project solutions. Keywords: Automation, process management, information management technology, visual system, intelligent systems, TV monitoring, surface exploitation, clay, Majdan III, Potisje-Kanjiza.

Jan 1, 2003

By X. Shi, F. -Y. Wang

Automation and robotics are the keys to new intelligent autonomous mining systems that can remove operators from hazardous and stressful mining environments and provide the tools for greater productivity. This paper presents the components necessary for an Intelligent Task Control System (ITCS) for machine control in dynamic unstructured mining environments. In particular, the design details of a controller for an automated excavator are developed. The excavator controller uses fuzzy logic to interpret forces and torques gathered from a wrist mounted force/ torque sensor during the excavation process. This approach enables the transfer of human heuristics and expert knowledge to the controller. Several excavation tests using the fuzzy logic controller are described. These experimental results represent the first step toward an integrated approach that uses force/torque, vision and other sensor data to perform generic tasks in uncertain mining environments.

Jan 1, 1995

Automation and robotics are the keys to new intelligent autonomous mining systems which can remove operators from the hazardous and stressful mining environment and provide the tools for greater productivity. This pa-per presents the components necessary for a mining Intelligent Task Control System (ITCS) in dynamic unstructured mining environments. The proposed concept is applied to develop the ITCS for an autonomous excavator. The design and implementation of a fuzzy logic controller for an excavator that uses force/torque sensor feedback to complete excavation tasks is presented. Initial experimental results are also given.

Jan 1, 1994

By L. J. Jansen

Techniques utilized to incorporate geological data in computer modeling and ore reserve estimation have undergone considerable evolution during the past fifteen years. Computer analysis and evaluation of two precious metal deposits are presented as examples of innovative computer techniques developed at Asarco. The first is a gold deposit occurring in a steeply dipping Pre-Cambrian greenstone sequence. The second is a manto-like manganiferous silver deposit occurring in a relatively flat sequence of Late-Paleozoic sediments. In both deposits, four sub-horizontal zones of geological influence are evaluated.

Jan 1, 1985

By Louis J. Jansen, D. E. Ranta

Techniques utilized to incorporate geological data in computer modeling and ore reserve estimation have undergone considerable evolution during the past fifteen years. Computer analysis and evaluation of two precious metal deposits are presented as examples of innovative computer techniques developed at Asarco. The first is a gold deposit occurring in a steeply dipping Precambrian greens tone sequence. The second is a manto-like manganiferous silver deposit occurring in a relatively flat sequence of Late-Paleozoic sediments. In both deposits, four sub-horizontal zones of geological influence are evaluated.

Jan 1, 1992