Search Documents

By S. M. Copley, M. Yankova, E. Y. Yankov, J. A. Todd

"Nanophased coupled growth structures, with spacings of -10 nm, have been observed in banded microstructures produced by laser melting hypoeutectic Ag-Cu alloys. These coupled growth structures comprised a Cu-rich phase of width - 1 nm and a Ag-rich phase of width - 9 nm. In this paper, microstructural observations of nanophased coupled growth structures in hypo eutectic AgCu alloys are presented. Laser beam velocities for the transition from banded to microsegregation free microstructures are modelled and compared with experimental values. Models are presented to show that, at a critical undercooling, initial growth of a Ag-rich, metastable, extended solid solution is rapid but slows to a halt as copper is partitioned into the liquid at the solid/liquid interface. Following nucleation, the coupled growth structure then grows until the partitioned copper is consumed, at which point growth of the Ag-rich solid solution is again accelerated. This cycle then repeats resulting in banded microstructures comprised of 750 nm of the Ag-rich extended, metastable solid solution, followed by 250 nm of the coupled growth structure.1. Structural Studies of Laser Melted and Resolidified TrailsPresented here are observations of laser melted and resolidified trails in Ag-Cu alloys obtained at beam velocities ranging from 0.7 to 34 cm S·I. When the laser beam is scanned along the surface (positive x-direction) with a velocity Vb a melt pool with the shape given in Fig. 1a moves with the beam. The isotherms move with the velocity, Vi,. = Vb cos.p. Calculations employing the thermal analysis of Kou, Hsu and Mehrabian [1] for the beam velocities of this investigation and for the thermal properties of AgCu alloys, indicated that, .p, the angle between the isotherm velocity and beam velocity should be small at the surface where microstructural studies were made. This prediction was supported by observations of trail cross-sections. Based on these observations, and the calculations which include latent heat effects, the isotherm velocity for observations near the surface in our investigation was taken to be 27 cm S-I."

Jan 1, 1994

By S. P. Marsh, M. E. Glicksman

"The effect of capillarity-driven diffusion on the recalescence of mushy zones is studied in pure materials. The solid-liquid mixture is formed by rapid partial solidification of an initially undercooled melt, and the ratio of the two phases is subsequently maintained constant by an externally imposed adiabatic constraint. A novel technique has been developed that permits tracking of the kinetics of the diffusion-controlled evolution process in situ using precision temperature measurements averaged on a length scale larger than that of the microstructure.The mean ""temperature of a mushy zone is slightly below the bulk equilibrium melting point, and is related to a characteristic length scale of the microstructure through an appropriate statistical average of the GibbsThomson equation. Theoretical considerations indicate that the diffusion controlled recalescence will progress as t- l / 3, where t is time. This behavior is experimentally verified for both succinonitrile (SCN) and ethylene carbonate (ETC), which have markedly different morphologies. The kinetic rate constant is observed to increase monotonically with increasing volume fraction of solid in the two-phase mixtures, although a firm theoretical foundation for this result has not been developed.INTRODUCTIONA dispersed multiphase system seeking equilibrium will generally contain variations in the local .free energy density. These density variations arise from such factors as variations in the bulk free energies of the phases and the distribution of interfacial energies. In this study, we examine the kinetics of diffusion-controlled recalescence in 1 solid-liquid mixture of a pure substance at its melting point. This type of two-phase system is particularly convenient to analyze because of the well-characterized physical properties of pure phases (crystals and their melts) and their interfacial energies, and the absence of any solutal effects."

Jan 1, 1986

By O. P. Pandey, Rama Arora, Gurmel Singh, Suresh Kumar

The tribological behavior of Dual Particles Size (DPS) rutile reinforced LM13 alloy composite was investigated under varying applied pressure from 125 kPa to 625 kPa at a constant sliding speed of 1.6 m/s. In the present studies, 15 wt.% of rutile particles of different sizes (50-75 μm and 106-125 μm) are reinforced in the Al-12Si alloy (LM13) by liquid metallurgy route. Microhardness of the prepared samples was measured in different phases. Microstructure, wear mechanism and surface morphology of the wear surfaces and debris was observed under optical and scanning electron microscope. The change in wear behavior has been explained with reference to the observed EDS analysis of the wear track and debris. However, an interesting change in wear feature, mild to severe wear transition at critical pressure was noticed in wear behavior of the composite. The Al-DPS composite has immense potential to be used as a component material for tribological applications.

Jan 1, 2015

By Yotamu Stephen Rainford Hara

"The aim of our work is to investigate a low energy and clean route for the recovery of copper and cobalt from complex sulphide mineral concentrates. The mineral concentrates were roasted in air, in the presence of CaO (MS + CaO + 202 =MO+ CaS04) at temperatures below 973K. The roasted products containing CuO, CoO and Fe203 were carbothermically reduced at 1073K within an hour to preferentially reduce copper and cobalt. The kinetics of reactions were studied using the thermogravimetric technique and by characterisation ofreaction products using the XRDSEM-EDX techniques. The effects of MS:CaO ratio, roasting temperatures and physical nature of the mineral concentrates were analysed. The method for capturing S02 by forming CaS04 was analysed for reuse in the process. The energy balance for the above process is compared with that of conventional continuous smelting/converting process.1.0 IntroductionCopper sulphide mineral concentrates from Zambia contains substantial amouot of cobalt. The cobalt metal content in the concentrates ranges between 0.7 and 2 % weight, which corresponds to 3 and 9 % weight copper, based on the spot price of copper ($7 386/tone) and cobalt ($31 000/tone). Although the traditional approach using a combination of roasting-leaching-electrowining steps can be applied to recover copper and cobalt from sulphide mineral concentrates [1-4], there are two major draw backs of the traditional process: (i) the S02 emitted during roasting is too lean for economical conversion for sulphuric acid manufacture, which causes serious environmental pollution. (ii) silver and gold which are normally present in the sulphide concentrates are lost out [5] because they are not leachable by H2S04 or HCl which are the common leachants. The above two problems have been overcome by adopting flash smelting in which a rich S02 gas above 20% is produced [1, 5] and successfully converted into sulphuric acid. The precious metals tend to partition to blister copper and recovered during refming. However, nearly all cobalt is lost into the slag phase uoder oxidising condition which prevails during flash smelting. It is important to note that the cobalt content in the slag can be up to 2.6 % weight [6]. The recovery of cobalt from the slag is a process which requires huge amouot of energy since the slag is smelted above 1873K [6]. With a view of minimising the amouot of energy and S02 emission during metal recovery, our investigation involves roasting the sulphide concentrates in the presence of lime and reducing the roasted samples with carbon."

Jan 1, 2013

By Jim Hardy, Tim McKnight

"The thermal mass flow controller, or MFC, has become an instrument of choice for the monitoring and controlling of process gas flow throughout the materials processing industry. In the semiconductor industry, these MFCs are used on over 70% of the processing tools. Reliability and accuracy are major concerns for the users of the MFCs. Calibration and characterization technologies for the development and implementation of mass flow devices are described. Sources of inaccuracy in process gas handling are described, and a model to correct for these inaccuracies is outlined. A gravimetric calibrator is described that allows flow sensors to be calibrated in corrosive, reactive gases to an accuracy of 0.3% of reading, at least an order of magnitude better than previously possible. All described capabilities are implemented in a Department of Energy User Facility which is available to industry and universities to test and develop gas flow sensors and controllers and evaluate their performance related to environmental effects, reliability, reproducibility, and accuracy.IntroductionMaterials processing is at the heart of semiconductor manufacturing. To make today's advanced integrated circuits, silicon wafers are subjected to over 200 process steps. Most of these steps involve processes such as etching, implanting, diffusion, annealing, deposition, and lithography (resist deposition and hardening). Often one or more process gases are used to complete the process step. To achieve the quality and performance required in the micro devices, accurate measurement and control of these gases is essential. The Oak Ridge National Laboratory (ORNL), in conjunction with the semiconductor industry, has been working to improve process gas measurement and control accuracy and reliability. Standardized test methods have been developed to characterize and benchmark the performance of mass flow controllers (MFCs), the method of choice for monitoring and controlling gas delivery. Testbeds have been designed and fabricated to produce repeatable and accurate data using these standards. Baseline testing was performed along with development of a unique mass flow instrument, the gravimetric calibrator."

Jan 1, 1997

By Kazuteru Tozcwa

The oxidation of several sulfide minerals in aqueous ammoniacal solution is discussed thermodynamically. The region in which Cu(NH3)2 4+ is stable has been estimated as a function of pH and concentration of total ammonia, {[NH3) + [NH4)}. In ammonia leaching when copper in sulfides is assumed to be extracted in the form of Cu(NH3)2 which will be rapidly converted to cupric ammine, thermodynamic data predict that such minerals are oxidized readily in the following order, CuS, Cu2S, CuFeS2, ZnS, NiS, Ag2S. This agrees with investigations on ammonia leaching of sulfide minerals, reported previously. The leaching of copper sulfide concentrate has been examined experimentally. Copper in a copper sulfide concentrate, in which the main constituents were chalcopyrite and pyrite, was effective¬ly extracted. The copper extraction was affected by factors such as (1) agitation intensity, (2) oxygen partial pressure, (3) NH3/Cu molar ratio, (4) leaching temperature and (5) addition of ammonium sulfate. From the results obtained in this work, it is concluded that mass transfer of oxygen plays the most important role in ammonia leaching of copper sulfide minerals.

Jan 1, 1976

By F. J. Hogan

In early 1982 Atlantic Cement Company, a wholly-owned subsidiary of Newmont Mining Corp. will come on line with a new water granulating grinding facility at Sparrows Point, Maryland to produce 800, 000 tons a year of separately ground granulated blast-furnace slag. The process and product will be unique to the United States. This paper will review some initial investigations undertaken to evaluate the cementitious properties of granulated slag. The effect of slag fineness on strength development is discussed and data is presented showing a relationship between glass content and hydraulicity and grindability of slag.

Jan 1, 1982

By Julie M. Melluish

The metallurgical response of the Point Leamington deposit has been studied. Two series of bench tests were conducted and various ore samples and flotation products were examined using image analysis techniques. The majority of sphalerite and chalcopyrite grains in this texturally complex ore were found to be smaller than 10 micrometres. Copper recoveries were low with losses mainly as fine inclusions in pyrite. Sphalerite recoveries were somewhat better due to a generally coarser habit. Gold and silver recoveries were also low and only solid solution silver was identified in the ore. The deposit shows poor economic prospects unless additional tonnage of high grade zinc ore can be delineated.

Jan 1, 1989

By Ryokichi Shimpo, Akio Fuwa

"The process-measurements of copper smelters in Japan were investigated for the summary of the latest technique and for the fundamental study of process control. The smelters investigated are those employing flash smelting furnace and P.S. converter, one reverberatory furnace and P.S. converter, and one continuous smelting converting furnace (M.I. process). Respective process is then considered, consisted of several reactors of different functions. The measurement methods were summarized in each reactor, including the measurement points. The methods of chemical analyses of the samples in each reactor were also investigated.IntroductionAn investigation on the process measurements, chemical analyses, and system control in copper smelters in Japan were carried out for understanding and summarizing the technique of the pyrometallurgical copper smelting operations. The typical seven processes in six copper smelters were investigated in the period from 1985 to 1987. The smelters investigated were Touyo Smelter of Sumitomo Metal Mining Co., Ltd., Kosaka Smelter of Dowa Mining Co., Ltd., Saganoseki Smelter of Nippon Mining Co., Ltd., Tamano Smelter of Hibi Kyodo Smelting Co., Ltd., Ashio Smelter of Furukawa Co., Ltd. and Naoshima Smelter of Mitsubishi Metal Co., Ltd. They include five flash smelting furnace and P.S. converter systems, one Mitsubishi continuous smelting and converting process (M.I. process), and one reverberatory furnace and P.S. converter system.The investigation was performed by making inquiries about the measurements, chemical analyses, system control, and their future prospects to the engineers in each smelter and by summarizing up in each item. The system control and future prospects were summarized in another paper titled ""Process Control Scheme of Copper Smelting Processes in Japan and Future View."

Jan 1, 1989

By A. J. Rigby

Current practices employing porous plugs to inject nitrogen into molten copper during primary smelting are described. Nitrogen stirring increases heat transfer to the bath, eliminates temperature stratifications, and improves efficiency during the steps of desulfurization and deoxidation. The opportunity to use porous plugs as the means to introduce reducing gases to deoxidize copper is also discussed. Previously reported laboratory results using porous plugs, which point to very high utilization efficiencies of hydrogen when used as the reducing gas, are again reviewed. Advances in the design of the porous plug, and the introduction of a system enabling external replacement of plugs is also discussed.

Jan 1, 1999

By Thomas J. Keefe, O&apos

The effects of cobalt, B-naphthol, glue and antimony on the polarization behavior of zinc sulfate electrolyte were investigated. It was found that B-naphthol was beneficial in reducing the detrimental effects of cobalt while antimony and excess glue were each harmful. Since the nu cl eat ion over potential was insensiti1ve to coba1t, other regions of the polarization curve were used to indicate electrolyte balance. The low? current density area occurring in the reverse or anodic sweep direction was? often an indicator when an ?unstable condition existed. The two parameters evaluated were the degree of inflection in the polarization curve in the low current density region during scanning and the rate of current rise observed when the sample was potentiostated at -0.781 Volts (SHE). Using this technique, a two-additive system was shown to be desirable to control cobalt and antimony containing electrolytes. The structure of the deposits was examined using scanning electron microscope techniques.

Jan 1, 1985

By Vladimir Mindin

Simulation of complex equilibria is usually done in the P-T-X coordinates, where "Xu is the amount of individual chemical components in the system. This approach is not productive in some very important cases: (i) investigation of "open" systems, (ii) determination of coordinates (trajectories) of mono-variant points, among others. To solve these and some other problems, we use the idea of chemical potentials of elements (CPE) of the system. A system of different coordinates axes (CPE-axes ) leads to a new strategy of simulation, observing the results of the simulation, and to efficient technology of compressing and storage the data of the simulation.

Jan 1, 1994

By M. J. Bagshaw, J. D. Hunt, R. M. Jordan

"Continuous casting processes, and the roll casting process in particular, offer considerable potential to the Aluminium industry, both meatallurgically and economically.The three major limiting process problems that occur during roll casting are Centre Line Segregation', 'Sticking' where metal adheres to the rolls during casting, and 'Heat Line' formation. 'Heat Lines' are localised semi-continuous longitudinal defects, usually a few cms in width, where the cast metal leaves the roll bite partially molten. These defects occur at relatively low casting speeds when the mean slab exit temperature remains several hundred degrees below the solidus temperature. The objective of the work described here is to develop a better understanding of the roll casting process in general, and in particular, to understand the phenomenon of 'Heat Line' formation.A steady state two dimensional finite difference model has been developed to describe the roll casting process, incorporating a variable heat transfer coefficient through the roll bite. In the model the difference equations are formulated using a control volume method and latent heat is incorporated according to the Scheil equation. A Gauss-Seidel type technique is used to obtain the solution. Because the rate of heat evolution is non-linear the temperature in each box is determined by using a Newton-Raphson method. The solution for a box can be multi valued and therefore lead to instability particularly near the vicinity of the front. A stability 'criterion is presented which shows that to obtain a stable solution it is better to have long narrow boxes rather than boxes with small dimensions in both directions.The model explains why heat lines form in terms of the variable slab/roll heat transfer coefficient.Experimental measurements of slab exit temperatures are also presented. These were obtained on a Hunter twin roll caster for the binary AI-Cu system, at two compositions over as wide a range· of casting speeds as possible. The experimental results are compared with the predicted ones."

Jan 1, 1986

By Hongbo Zhao, Jun Wang, Wenqing Qin, Guanzhou Qiu

Jan 1, 2015

By Pertti Koukkari

The novel Jarogain process combines treatment of the jarosite residue of zinc manufacturing and processing of arc furnace dust from steelmaking to a holistic recovery technology. The new hydrometallurgical approach is targeted to recover the major constituents (Fe, Zn, Pb) as well as valuable components such as Ag, Au, In and Ga from the jarosite-dust mixture as reusable concentrates. The fractionation process proposed by VTT and Aalto University takes advantage of jarosite being readily fine powder and directly available for wet chemical processing. Jarogain process provides an energy efficient opportunity for jarosite utilization as value added products. The experimental proof-of-concept of key stages of the process will be outlined with a comparison of available pyrometallurgical treatments of jarosite waste. The techno-economical assessment is based on estimated investment and variable production cost using the discounted cash flow (DCF) analysis.

By Emanuel Negrao Macedo, Edinaldo Cunha, Mauro Oliveira, Jose Antonio da Silva Souza

"This paper presents the study of the increasing addition influence of the bauxite waste in some properties of polymeric matrices composites reinforced with natural fiber: Curaua (Ananas Erectifolius smith). There were evaluated properties as density, tensile and flexural resistances. The high pH provided by the waste is used as hydrolysis agent, providing the pectin cement dissolution of the fiber bundles, and therefore, improving the mechanical adhesion in the fibermatrix interface and the increase of the fiber bundles aspect ratio. Furthermore, the content of silico-aluminous material in the waste provides increase in the composite abrasivity, which is destined to civil and naval construction. The fact of being a low-cost and highly available waste turns the red mud in a high potential material as polymeric composite filler.IntroductionRed mud is an insoluble residue, originated from the bauxite refining through the Bayer Process [1]. It is an Iron Oxide rich material [2] (substance responsible for the red brick color), it has a complex chemical composition [3], and its composition is highly dependent of the type of bauxite used in the process [4]. It has high alkalinity (pH= 10 - 12.5) and a very small solids size distribution (95% diameter< 44µm) [1], what turns the red mud a serious environmental pollutant.The utilization of fillers on composite materials is done after many necessities; however, one of the major necessities is the cost reduction [5]. Furthermore, mechanical and thermal properties of polymers usually are improved by the addition of inorganic fillers [6], being an example of this improvement the reduction of the flammability of polymer matrixes due to the addition of functional clays [7]. In this way, the red mud becomes potential filler for composites, since cheap and easily available fillers (like red mud) are a good option to reduce costs [8]."

Jan 1, 2013

By Jingwei Lou, Bing Li, Suzhen Li, Miao Shen, Jianguo Yu

"As a main impurity in primary lithium metal, magnesium is difficult to remove because of the very close relative volatility of the two metals. Electrochemical refining provides a possibility to completely remove Mg in the LiCl-KCl melt prior to Li reduction. MgCl2 reduction processes in LiCl-KCl- MgCl2 melt were investigated by cyclic voltammetry (CV), square wave voltammetry (SWV), chronoamperometry and chronopotentiometry. Then potentiostatic electrolysis was carried out and Mg (II) ion was reduced onto a liquid lead cathode from the LiCl-KCl-MgCl2 melt at the Mg deposition potential. The results show that Mg ( II ) is reduced in one step with two-electron transfer. The reduction potential of Mg ( II ) was well defined. The reduction of Mg( II) results in Li ( I ) underpotential deposition at 0.2V more negative potential than that of Mg( II) reduction. Therefore, in order to prevent Li ( I ) from codeposition with Mg, accurately controlling Mg ( II) reduction potential during the potentiostatic electrolysis was necessary. Ninety three to 99 % removal rate of MgCl2 was achieved after 8-12 h electrolysis when liquid lead was used as cathode.IntroductionMetallic Li has been widely used in batteries, light weight alloys and in fusion reactors because of its excellent properties. Currently, the only way in industry to produce metallic Li is by electrowinning from molten LiCl-KCl at about 450 °C [l-5]. LiCl-KCl is the only electrolyte used, because they presents a lower eutectic temperature and KCl shows a slightly higher theoretical decomposition voltage than LiCl, as shown in Table l .The produced metallic Li generally contains 1-2 wt% impurities including Na, K, Al, Ca, Mg, Si, etc. [6l, which are derived from the corresponding metal chloride compounds or metal oxide compounds existing in the LiCl and/or KCl raw materials. These impurities have to be removed by subsequent vacuum distillation at high temperatures to meet the requirements for metal Li purity in the final products. Separation of Mg from Li by vacuum distillation is difficult because their relative volatilities are very close, as shown in Table 2."

Jan 1, 2011

By Sumantra Mandal

The hot deformed microstructure of the 15Cr-15Ni-2.2Mo-Ti modified austenitic stainless steel (commonly known as alloy D9) was investigated employing electron backscatter diffraction (EBSD). Hot compression tests were conducted in a Gleeble thermo-mechanical simulator at temperatures of 1173K-1373K (in steps of 100K) with a strain rate of 10 and 100 s-1 to different strains. Various kinds of deformation patterns were observed inside the deformed grains. These were inferred as the development of geometrically necessary boundaries or formation of parallel set of micro-bands. Recrystallized grains were partitioned from the deformed grains employing grain orientation spread approach. Extent of dynamic recrystallization (DRX) was found to be minimal at 1173K. DRX was predominantly found to happen at and above 1273K which increases with increase in strain. DRX nucleation and development mechanisms were discussed with respect to bulging of the parent grains and sub-grain rotation. Special emphasize is given on the role of annealing twins on DRX nucleation and subsequent expansion.

Jan 1, 2009

By P. Felix

A discussion on the need of visualization and animation tools in modelling solidification processes is made. An outline of an approach for the production of a video computer animation is provided. A number of examples including, 2 and 3 dimensional melting, filling, and macrosegregation are presented.

Jan 1, 1993

By Kazuyoshi Sato, Keizo Uematsu, Nozomu Uchida

"Confocal fluorescence scanning laser microscope was applied to characterize the surface flaw of ceramics in great detail. A high potential -of the characterization technique is presented first. Then the technique was applied to clarify the relationship between the flexural strength of ceramics and the surface flaw. This kind of direct information of surface flaw should be essential for the fundamental study in this area, but has been lacking. The examination revealed that large defects are present on the machined surface of ceramics. Their size is consistent to the flexural strength measured on the material. The characterization tool was also applied to examine the formation of surface flaw in machining of ceramics.IntroductionClarification of fracture origin should be the starting point in the study on strength in ceramics. However, this task has been extremely difficult in some ceramics, such as an alumina ceramics. It may break from both internal and surface flaws. The former should reflect the quality of production process and the latter the machining. Examination of surface flaws should be very important for developing a better machining method for ceramics. The knowledge may valuable for establishing a better production process also.ExperimentAlumina Referceram (JFCC) was used as samples. They are cut to size of 3x4x40mm, and the surfaces were ground to meet the requirements of testing method for flexural strength of fine ceramics, JIS R 1601. They were soaked in an aqueous solution of fluorescence dye and evacuated with an aspirator for an hour to allow the solution penetrate into surface flaws. After excessive solution remained on the surface was removed by gentle washing, the specimens were dried at 120°C for 48 hours. The 4 point bending mode was applied to measure the fracture strength."

Jan 1, 2000