Search Documents

By George P. Schivley

When drilling blast holes, with roller cone bits, a phenomenon known as drilling vibration can occur. It is characterized by either axial or lateral modes of periodic motion of the drill pipe; superimposed on the time-average angular motion of the drill pipe provided by the drill rig rotary head and the vertical motion associated with the penetration rate of the tricone bit into the rock being drilled. This periodic motion can be very severe and, if appropriate action is not initiated by the drill rig operator, could lead to structural damage to the drill rig. Ultimately, the occurrence of drilling vibration limits the productivity potential of a rotary drill.

Jan 1, 1997

By G Alan Foster

This paper discusses the cause of air blast and modern techniques to reduce this at the source. In addition it raises the problem of their marked variability due to prevailing weather conditions and how weather data can be obtained and used in the control of air blast.

Jan 1, 1975

By R Keller, R Law

In the rush to beat the clock before the handover of Hong Kong back to China in June of 1997, an unprecedented amount of infrastructure work is being undertaken at a breakneck pace. In the middle of this construction explosion, on this island of barren granite , stands some of the most concerning and restrictive slope stability measures. So conservative, these measures impact blasting and vibration control to an extent unmatched anywhere in the world.

Jan 1, 1996

By Karl Ingmarsson

A model for drilling productivity and total drilling cost is presented. It specifically addresses down-thehole drilling, but also covers other drilling methods. The important factors are: 1, productivity in tons drilled; and 2, total cost per drill ton. For non-blasthole applications these factors are measured in drill feet and cost per foot. The model focuses on the entire system and allows the operator to optimize the system based on individual drilling conditions.

Jan 1, 1998

By Donald Little, Larry Unger

This paper will give a detailed insight into hard rock, large diameter surface blasting including some practical tips to improve blasting practices. These tips will be non-technical, of the nuts and bolts type, intended to help the man in the boots. The paper will begin with the importance of communication between the engineering department and the blasters. What looks good on the mine development map might not blast very well. Tight inside corners, 90 degree outside corners, too few rows; are a few of these problems.

Jan 1, 2006

By Theodore C. Hile, Floyd P. Henry, Ken Gragg

"Conventional explosive-storage methods usually rely on combinations of earth and concrete barriers, along with sufficient distance between limited explosive loads, to avoid accidental conflagration. However, under many circumstances, Air National Guard (ANG) facilities co-located with civilian airfields have trouble meeting necessary Quantity-Distance (Q-D) requirements for Explosive Hazard Class/Division 1.1 and 1.4 materials. Because of the danger posed by explosives stored in earthcovered magazines (ECMs) too close to civilian activities, ANG units often find itdifftcult to maintain adequate stores of ordnance needed to meet unit mission goals."

Jan 1, 1999

By J L. Jethwa, A G. Gaithankar

The paper deals with a software method developed to design the optimum blast parameters for tunnels and mine roadways for a given set of geo-mining condition without any major discontinuity. The application of the software is presently limited to 8 D-ahaped excavation where inclined hole cut or four-section parallel cut is used with smooth blasting technique.

Jan 1, 1993

By Patricia Mendoza Watson, Lundquist Robert G

The velocity with which the burden moves after blasting is of concern for safety and economic reasons. Models developed for motion velocity by various researchers were reviewed and likely model parameters were used to develop statistically significant models. Regression analysis and residual analysis were used to determine the model coefficients and the accuracy of the models.

Jan 1, 1990

By Jeffrey E. Loney, Andrew F. McKnown

Recovery of contaminated groundwater migrating through bedrock can be very difficult due to the low transmissivity of many bedrock fracture systems. To overcome these difficulties, a system of controlled "trench" blasting has been used on several projects to assist in cutting off and collecting groundwater plumes in bedrock. By using a combination of trench blasting and presplitting techniques, linear "fracture" zones are created in appropriate locations to significantly increase flow into recovery wells and control plume migration.

Jan 1, 1995

By J T. Keim

Members and guests of the Society of Explosive Engineers, it's indeed a pleasure for a longtime practical user such as myself to have the ears of so many explosive experts for a few minutes just to express my feelings and concerns on blasting as well as the feelings and concerns of many other users and operators.

Jan 1, 1978

By David Davison, Richard Johnson

Metal-oxidant blends are ordinarily unsuitable as diiect replacements for explosives, because the reaction occurs too slowly. Oxide coatings protect metals, preventing or delaying reaction. By contrast, the electrically-activated reactive composites described below are configured as metal fibers or foils in close proximity to oxidants, with continuous electrical paths from one end to the other. By quickly vaporizing the metal component with an electrical pulse, a reactive composite will be activated, and the reaction will occur rapidly.

Jan 1, 1999

By Roger L. Keller

This paper covers the design and test blast procedures for several drop shafts and edits leading to the completion of a recent Rochester Pure Waters Expansion Project . Due to the projects "in-town" presence, and its close proximity to many sensitive vibration sites, very stringent ground vibration limitations and guidelines for blasting were places on each site.

Jan 1, 1991

By K Ramachandra Rao

This paper explains the methodology for assessing the efficiency of rockmass fragmentation by explosive blasting, from ground vibration frequency spectrum analysis of the blast event. Explosives are used in the mining, quarrying and construction industries for fragmenting rockmass to a suitable size. When an explosive charge is detonated, in addition to fragmenting the rockmass, it will also generate ground vibration and air vibrations. Efficiency of a blast depend upon percentage of blast energy wasted in generating ground vibrations and air vibrations.

Jan 1, 1994

By Kamal Wadhwa

Liquid oxygen explosives have been used in India for well over 5 decades now. These are being extensively used both for shallow and deep hole blasting in the various opencast mines and quarries for mining of coal, limestone, ironore, bauxite, magnesite etc. IOL Ltd., are the pioneers in the introduction of these explosives in India and are marketing these under the brand name 'LOXITE'.

Jan 1, 1991

By G Dean Barrett, Ed Jr Smith, Calvin J. Konya

The purpose of the project was two fold: 1. To determine whether Pyrodex, a propellant, manufactured by the Hodgdon Powder Company, could be used as a substitute for high explosives for presplitting in granite and other materials. 2. To determine if Pyrodex, a slow reacting propellant which produces no stress waves in rock because it reacts subsonically, could cause the rock to crack similar to the results achieved with high explosives.

Jan 1, 1986

By T Michael LeBlanc

Drill trajectory deviation is a recurring problem in vertical retreat stoping operations. As a result of this deviation, 60 kilogram (165 millimetre diameter) and 103 kilogram (302 millimetre diameter) explosive charges are routinely detonated beyond ore/waste contact zones. Consequently, there follows a reduction in finished stope wall stability and an increase in ore dilution.

Jan 1, 1996

By Curtis Garner

Griesemer Stone located in Springfield, Missouri has supplied aggregate in Southwest Missouri since 1946. In 1954 the decision was made to mine the formation and utilize the mined out area for warehouse space. As advancement proceeded, entrances and small diameter air shafts for ventilation were needed and had to be added. It was decided in 1989 to sink an 8' diameter air shaft designed to move 200,000 cubic feet of air per minute with the help of (4) four 50,000 CFM Loren Cook Fans.

Jan 1, 1991

By Curtis G. Kremer, Jeffrey L. Brummert

Blue Circle Cement's Ravena, New York quarry mines approximately 6.7 million tons of limestone per year. Blasting occurs approximately twice a week on three separate benches. Shots average 60,000 tons but can range up to 140,000 tons. Ongoing scrutiny of the drilling and blasting program allows for maximum blast efficiency which results in lower overall mining and crushing costs. Close cooperation between management and explosives supplier assures Blue Circle Cement's objective, "To develop, implement, and continuously improve a measurable drilling and blasting system that will optimize the total mining and crushing costs while ensuring compliance to safety and maintaining or reducing the environmental impacts of blasting".

Jan 1, 1994

By Erik K. Lauritzen, Jorgen Schneider, Niels Madsen

From 1986 to 1988 Kalaallit Tunisassiorfiat (KTU)/Gronlands Hjemmestyres Produktionsvirksomhed (the part of Greenland's own governing body which is in charge of production activities) has been responsible for blasting projects in the following 4 towns: Ilulissat/Jakobshavn, Qasigiannguit/ Christianshab, Qeqertarsuaq/Godhavn, Sisimiut/Holsteinsborg

Jan 1, 1989

By Sharon K. Reamer, Yvan Sifre, Klaus-Gunter Hinzen

"Three case studies are presented that illustrate the successful application of firing timeoptimization (hybrid modeling) in the quarry environment and for a construction site. In allcases, the method requires the measurement of at least one in situ, single hole explosion asa representative model of the desired blast design."

Jan 1, 1993