Search Documents

By M. Barsky, E. Barsky

It is generally accepted that the optimal flow velocity for gravity classification is the final particle settling velocity or, which is the same, the particle spin velocity. However, we have found differences between the settling velocities and the spin velocities of the very same particles. Here we present the results of experiments in a cascading gravitational classifier comprising eleven stages. The feed material was introduced at each stage successively, from the first to the eleventh. The optimal flow velocity was determined for each case. From these experiments it follows that the value of the optimal flow velocity depends to a greater extent on the point of introduction of the feed (i.e., on the design of the device) than it does on the interaction between the solid phase and the flow.

Jan 1, 2003

By M. Nonaka

An attempt to produce fuel from biomass waste by hydrothermal treatment has been made with expectation to effectively utilize a renewable source of energy and an unexploited energy resource. In this paper, we have used empty fruit bunch (EFB) that is a residue after recovery of crude palm oil from palm oil trees in a plantation in a tropic country. A hydrothermal treatment was conducted using a 500 mL autoclave, with alkali (K2CO3) catalyst. EFB was decomposed more by alkali catalyst of lower alkali content and rather polymerized in higher catalytic region. The functional group composition of the solid phase oil is similar independent of alkali content, however its burning characteristic became more incombustible with increasing alkali content.

Jan 1, 2014

By E. V. Leont'eva, V. R. Vafin, A. G. Kladova, N. L. Medyanik, A. P. Ponomarev

"The thermochemical technology for recovery gold, silver from mature flotation tailings of pyrite ores by two-stage sintering with chlorine-ammonium reagents and leaching of bakes with water is developed. The economic effect of the technology implementation is calculated. KEYWORDS Gold and silver recovery, mature flotation tailings, pyrite ores, chlorine-ammonium reagents, leaching INTRODUCTION The relevance of processing the technogenic reserves of ore mining and concentration wastes accumulated over the long operation periods of mineral deposits is beyond doubt. Hundreds of tons of precious and non-ferrous metals that were not recovered during the primary processing are concentrated in the accumulated wastes. For example, tailing storage facilities (TSF) at the mineral processing plants in the Southern Urals region of Russia hold more than one hundred tons of gold and thousands of tons of silver in the mature flotation tailings (MFT) of copper pyrite ores. Secondary processing of technogenic materials is facilitated by the fact that they are preprocessed — ground and compactly deposited on the surface, but complicated by the low (compared to ores) grade, uneven distribution of the valuable minerals, altered and unstable material composition of the mineral feed. This leads to low recovery rates of valuable metals by conventional physicochemical processing methods. It is necessary to develop innovative methods of deep integrated processing of industrial wastes, based on the study of the material composition of specific technogenic mineral resources and based on ensuring the environmental safety of the resulting secondary waste. MATERIALS AND METHODS The object of this study are the MFT of Uchaly Concentrator in the Republic of Bashkortostan, Russia, which processes copper pyrite and copper-zinc ores. According to the data of particle size, chemical, X-ray phase, and optical microscopic analyzes, samples of the MFT are characterized by considerable particle fineness (the fraction of the size class -41 µm is 89-90%), low grade of gold (1.7-2.0 g/t) and silver (18.0-19.5 g/t), comparable grades of iron (23.0-26.8%) and sulfur (28.1-28.7), but different grades of copper (0.12 - 0.73%) and zinc (0.34-1.26%). The most common mineral in the samples is pyrite (50 - 56%), found in intergrowth with grains of other sulfides (0.1-4%) - sphalerite, tennantite, chalcopyrite, covellite. Quartz and aluminosilicates are the dominant rock minerals (21-36%). Based on the results of the phase analysis, it was established that approximately 70% of the gold in the samples is found in a form that is resistant to cyanidation — it is locked in sulfides (52-56%) and quartz and coated by films. Along with sulfides and rock minerals, common gold and silver minerals (chalcogenides, intermetallides, native gold) in the form of submicro- and nano-sized precipitates are also associated with intergrowth of a complex structure. These features of the material composition allow classifying the MFT of the pyrite ores as a mature feed material and emphasize the need for chemical non-cyanide methods to recover gold and silver from the mature minerals and associations they are found in."

Jan 1, 2018

By Amir Hajizadeh Omran, Mehdi Irannajad, Sima Mohammadnejad, Fardis Nakhaei

"This study presents an experimental program performed to investigate the effects of flotation variables including gas flow rate, froth depth, slurry solids percent, frother/collector dosage and pH on the froth bubble size during desulfurization of an iron ore. These conditions were varied using a central composite design (CCD). Image analysis techniques have been developed and used successfully to characterize the froth bubble size. Results of the CCD experiments showed that the flotation variables have different effects on the froth bubble size. The froth height, air flowrate, pH and solid content had the most important influence on the froth bubble size. The interaction between the collector-frother, pH-collector, frother-air flowrate, solid content-froth height, pH-froth height and solid content-pH were also significant. Process state can be accurately deduced from the froth surface appearance, providing a convenient way to quantify the parameters as a function of the process control. INTRODUCTION Flotation processes are subjected to a wide variety of process disturbances, some of which are made by the change in mineral features and others to variation in operating procedures. Feed and air flow rates, densities, size distributions and shapes of particles, surface properties, and reagent dosages and compositions can all change, often with significant effect on the performance of the plant (Moolman et al., 1996a). Flotation process efficiency is governed by the wettability of the solid as well as the surface tension at the liquid-gas. Both of these properties are influenced by operational conditions encountering in a flotation process. The structure of froths developed on the pulp surfaces of flotation cells has a remarkable effect on both the grade and recovery of minerals in the concentrate (Shean and Cilliers, 2011)."

Jan 1, 2018

By Hillary Williams, Ronghao Li, Christopher Marion, Kristian E. Waters, Devin Hundt

"Zircon is an important mineral for ceramic, foundry, casting, and refractory applications; and it is the worlds primary source for zirconium. Zircon can also contain large and valuable proportions of other valuable metals, such as rare earth elements and hafnium. The Nechalcho deposit (Northwest Territories, Canad), is a hard rock REE deposit, which looks to recover zircon for its Zr and REE content. In this deposit, zircon is finely disseminated and associated with predominately silicate gangue minerals. Most of the work to date has focused on the beneficiation of mineral sand deposit, which typically remove silicate gangue minerals through physical separation steps. Therefore, the separation of zircon from silicate gangue, such as quartz, by flotation, has received little attention. This work used zeta potential measurements and microflotation experiments to understand the interaction between zircon and six different collectors (sodium oleate, sodium dodecyl sulphate, dodecylamine, SM 15, K-octyl hydroxamate and Florrea 7510). The results were compared with those of quartz. This study indicated that selective separation of zircon from quartz without the use of selective depressants or activators is likely challenging. The findings suggested sodium oleate and SM 15 only offered selective flotation of zircon in highly acidic conditions. Separation by the flotation of quartz is possible using sodium dodecyl sulphate, dodecylamine and K-octylhydroxamate. However, selective separation is highly dependant on collector dosage, for dodecylamine, and the selective activation of quartz, for sodium dodecyl sulphate and K-octyl hydroximate. Florrea 7510 offered poor recoveries for both zircon and quartz.INTRODUCTIONZircon (ZrSiO2) is a nesosilicate mineral which has a wide variety of applications, due to its hardness, opaqueness and resistance to heat and corrosion. Its major end uses are in ceramic, foundry, casting, and refractory applications (Bedinger, 2017). Zircon is also the most abundant zirconium (Zr) bearing mineral in the earths crust and is the principal economic source of Zr (primarily used in alloys for heat and corrosion resistance) and zirconia (ZrO2) (primarily used in ceramics) (Bedinger, 2017; Milnes and Fitzpatrick, 1989). Zircon forms in silicate melts and can often contain large proportions of other valuable metals such as rare earth elements (REE), and hafnium (zircon is the primary source of hafnium) (Bedinger, 2017; Belousova et al., 2002; Orlova, 2007). A common chemical formula showing the range of substitution in zircon is (Zr,Hf,Th,U,REE,Ca,Fe,Nb,Ta)(Si,P)O4 (Orlova, 2007)."

Jan 1, 2018

By K. Saberyan

In this study the extraction of zirconium and hafnium has been investigated by solvent extraction using Cyanex 302 in various media such as nitric, sulfuric and hydrochloric acid has been investigated. Effect of various parameters such as type and acid concentration, extractant concentration, type of diluent, equilibrium time, various foreign ions and finally type and concentration of strip-ping agent have been studied. The results showed that nitric acid was optimum media for extraction of zirconium and hafnium. The extraction of zirconium and hafnium occurred quantitatively in the concentration of higher than 4 M nitric acid but in hydrochloric acid media, quantitative extraction obtains over 8 M HCl. In sulfuric acid media, extraction of zirconium and hafnium is negligible. Stripping studies showed that the optimum reagent for stripping was 0.5M sulfuric acid.

Jan 1, 2014

By Y. Q. Qui

In the bauxite flotation process for desilication, the middling treatment mode is the important factor to raise the flotation recovery of the preparation concentrate. The middling treatment mode mainly depends on A/S and the size composition. However, similar ratio of A/S should not be the single factor of re-dressing, size composition plays an important role also. Re-dressing the middling mixed with the tailings of concentrated to the rough ground for desilication and the concentrate of scavenged to the fine ground for desilication to raise the recovery of 5.83%, when compared two flow sheet schemes.

Jan 1, 2014

By N. Karapinar

Ferrihydrite, a member of iron oxides family, has been used as an adsorbent for the removal of heavy metal ions from industrial wastewater. The success of the operation depends mainly on the efficient removal of ferrihydrite from the aqueous phase. Hence, the emphasis of this study was given on the separation of ferrihydrite by high gradient magnetic separation (HGMS) method to overcome solid-liquid separation difficulties of ferrihydrite. Magnetic seeding technique in which the magnetite mineral was chosen as a seeding reagent was used to make magnetic separation available. The method clearly involves the attachment of ferrihydrite to a magnetic seed material and subsequent magnetic separation of ferrihydrite ? magnetite coagulates. Seeding of ferrihydrite with magnetic particles was achieved by exceeding the solubility limit of the ions in the presence of dispersed magnetite. Magnetic separation results of seeded ferrihydrite showed that maximum seeding performance is obtained in the pH range of 7.0~10.0. Iron/magnetite ratio had a marked effect on the separation of seeded iron oxide precipitate by HGMS. This ratio determines the operation parameters such as magnetic field strength and flow rate. It was concluded that when used with magnetic seeding technique, HGMS can be used to surpass separation difficulties of ferrihydrite used in adsorption-based treatment techniques.

Jan 1, 2014

By J. Roth

The increasing demand of the filler industry regarding fineness and better delaminated products led to the development of a series of different grinding machines, which differentiate basically by the grinding mechanism as well as the kind of classification. Spiral jetmills grind, as it is well known preferably by delamination, therefore a spiral jetmill with integrated dynamic classifier has been developed. Especially the enhancement of the functional properties of the used industrial mineral fillers is a factor of highly increasing importance. These properties are very often bound to the platy shape of the minerals expressed by the aspect ratio. The developed Spiral Jetmill shows sufficient ability for such delamination and therefore increases in aspect ratio. In a series of comparative tests the suitability and advantages of this system regarding achievable fineness down to the submicron range as well as the conservation or even improvement of the aspect ratio of different minerals has been studied. As an emphasis on the results application tests with certain materials in the plastics field have been conducted. Due to the fact that in this range the required specific energy for achieving the necessary fineness increases exponentially another target is to optimize the grinding efficiency. A special feed control system provides on one hand a sufficient load inside the mill to obtain maximum utilization of the applied energy and on the other hand to prevent the mill from overfilling and coming with this a poor classification. The integrated classifier is a combination of a high speed motor with directly attached classifier wheels. This unit on one hand grants the necessary high circumferential speed of up to 190 m/s for providing an exact top cut of the ultrafine products and on the other hand gives the required operational reliability for continuous operation. Hard grindable impurities, which enrich inside the mill chamber, can be rejected from the process leading to an even cleaner product. Comparative tests on a talc product with certain free quartz impurities showed a significant improvement of the final product with respectively low loss on rejected material. This effect again had a beneficiary impact on the suitability of the final product when used in plastics application.

Jan 1, 2014

By S. Dwarapudi

Pelletizing of Indian chromite ores is more challenging due to their high refractory nature. High Cr/Fe ratio and high MgO content in these ores demand high firing temperatures and longer firing cycles but often result in low strength fired pellets. Aim of this study was to develop cold bonded chromite pellets for smelting in submerged arc furnace (SAF) from chromite fines using suitable binder that induce less gangue into the pellets but cures quickly. Different binders were studied through laboratory pelletizing experiments for their suitability for cold bonding the pellets. As result, a composite binder comprising organic and inorganic binding agents was found to be suitable and pellets made from the same were tested for their low and high temperature behavior. High temperature reduction studies revealed that pellets were resistant to disintegration up to 1200 °C.

Sep 1, 2012

By M. Paymardi, A. Foroutan, T. P. Oladele, M. Abbaszadeh

"Reducing the amount of zinc and iron in lead concentrate is one of the important aspects of processing in lead and zinc flotation plants which results in improvement of lead concentrate quality and prevents zinc loss. In mineral flotation industries, lignin sulfonates are known for their depressant properties for both non-metallic and sulfide minerals such as pyrite and pyrrhotite.This paper investigates the effect of lignin sulfonate on flotation of galena, sphalerite and pyrite in sulfidic lead and zinc bearing ores. Batch flotation tests were carried out on a high pre-activated zinc samples. The feed contains 0.9% lead, 2.3% zinc and 7.5% iron. The dosage of all reagents such as sodium cyanide, zinc sulfate, ethyl xanthate and methyl isobutyl carbinol (MIBC) were kept constant for lead flotation step except calcium lignin sulfonate (CLS) that was varied between 0 and 80 gr/ton.Results for lead rougher concentrate showed that the grade of lead increased by 2.7% while the recovery decreased around 4 % at the highest dosage of CLS. Furthermore, zinc recovery decreased by 6.3% with no significant change in grade. Iron recovery in lead rougher concentrate decreased by 2.3 % while the grade changed around 1%. In sphalerite flotation step, CLS dosage was changed in the range of 0 to 80 gr/ton while the dosage of other reagents such as copper sulfate, lime, amil xanthate and MIBC were kept constant. In this step, no decreasing in grade and recovery of zinc was observed, while iron recovery decreased. It was suggested that CLS has a depression effect on sphalerite in conjunction with other zinc depressants such as zinc sulfate and sodium cyanide. CLS was further used in plant with non-pre-activated zinc minerals. Similar trends were observed in plant.INTRODUCTIONlead-zinc sulfide minerals play an important role in the production of lead and zinc metals in the mineral processing industry (Luo, Feng et al. 2016). Due to complexity of the lead-zinc ores mineralogy, in some situations, their flotation properties vary significantly from one deposit to another one even in itself (Bulatovic 2007)."

Jan 1, 2018

By V. I. Ryaboy, V. P. Kretov, S. E. Levkovets, I. V. Ryaboy

"Using the flotation of a gold-containing ore from a deposit in Kazakhstan as an example, we have conducted a study designing dialkyldithiophosphate collectors, in addition to xanthates, for the flotation of hard-toenrich gold-containing ores to increase gold recovery.The increased flotational ability of the dialkyldithiophosphates was determined by their surface activity at the liquid-gas interface and their hydrophobic ability, the changing of which allowed us to control the collecting power and selective ability of the dialkyldithiophosphates. The studying of the surface activity of aqueous solutions was done using the stalagmometric method and the evaluation of the hydrophobic ability was done in percentage of the relative value of the zinc ion binding in the solution in standard conditions.Studying the influence of surface activity in our designed dialkyldithiophosphate collectors, with their close hydrophobic ability, showed that even with a small increase in surface activity in their aqueous solutions, gold recovery increased by 2-3% in laboratory conditions. Using this enabled us first to apply the dialkyldithiophosphate collector BTF-161 at a plant in Kazakhstan, and then to introduce the specially designed dialkyldithiophosphate collector BTF-163, which has been in use since. Further study of dialkyldithiophosphate activity based on this concept showed us that for the range of short-chain dialkyldithiophosphate collectors with a chain length of up to ?5, the effectiveness of ore processing became lower the higher their surface activity got, with relatively small differences in their hydrophobic ability. For long-chain dialkyldithiophosphates with a chain length of over ?5, ore processing effectiveness increased with the increase of their hydrophobic ability.Based on these studies, a new effective dialkyldithiophosphate collector, BTF-1517, was designed. Using this reagent in continuous gold recovery tests allowed us to reach an 84.21% recovery with a concentrate quality of 15.66 g/t, while using the applied collector BTF-163 in similar conditions led to the recovery of 82.87% with a concentrate quality of 15.65%. As a result, the Kazakhstan processing plant decided to conduct industrial tests with the BTF-1517 collector."

Jan 1, 2018

By A. L. Hinde

The steady-state and dynamic behaviour of semi-autogenous grinding (SAG) mills are arguably best described using a population model that caters for the breakage kinetics and the material trans-port of rock and pulp inside the mill. Breakage kinetics are usually expressed in terms of a specific breakage rate function and a separate primary breakage distribution function. Material transport usually invokes the concept of a specific discharge rate function. Unfortunately, the breakage rate and breakage distribution functions for SAG mills are very difficult to estimate uniquely from plant data alone. Simplifying assumptions must be made to over-come this problem, which leads to many unresolved dilemmas with regard to whether or not the de-rived functions are accurate, precise, and reflect reality. For example, it is sometimes assumed that the breakage distribution function for a SAG mill treating run-of-mine ore can be derived from laboratory dropweight and tumbling tests on small rocks in narrow size ranges. Such tests hardly reflect the environmental conditions likely to be encountered in a pilot or production SAG mill where there is a wide spectrum of particle sizes. It is shown that the dilemmas associated with standard population balance models (models that utilise separate breakage rate and breakage distribution functions) can be overcome by expressing breakage behaviour inside a SAG mill in terms of a single function. This function is an energy-based cumulative breakage rate function defined as the fractional rate at which particles and rocks coarser than a given size break to below that size per unit specific energy input. A model for SAG milling is formulated, which invokes the concept of a cumulative breakage rate function. Comparisons are made between the mathematical structure of this ?simple model? and standard population balance models. Perhaps the most attractive feature of the ?simple model? is that the cumulative breakage rate function can be uniquely estimated from measurements of size distributions and mass flows of the feed and discharge streams together with the size distribution and holdup mass of the mill charge. Such measurement can easily be made at pilot scale. It is concluded that this simplified approach to SAG milling may turn out to be the quickest way to fully describe and quantify the performance of these very complex mills.

Jan 1, 2014

By E. R. Bobicki

"Low-grade ultramafic nickel ores, while representing a large potential nickel resource, are difficult to process due to their serpentine content. Microwave treatment is proposed as a technique to improve the beneficiation of ultramafic nickel ores by converting the constituent serpentine to olivine. The present paper reviews the microwave heating response of ultramafic nickel ores and resultant changes in mineralogy, as well as effects on grinding and slurry rheology. Beyond nickel extraction, microwave treatment improves the mineral carbon storage capacity of ultramafic ore tailings, providing a potential source of additional revenue via the sale of carbon credits. The combined positive effects, considered in the context of the whole operation, suggest an economically viable process is possible.INTRODUCTIONAs high-grade deposits become depleted, the processing of low-grade ores has become increasingly important. One such resource is low-grade ultramafic nickel ores. While representing a large source of nickel, these ores are difficult to process due to their serpentine content. Serpentine is a phyllosilicate mineral consisting of 1:1 stacked sheets of silica tetrahedra and magnesium hydroxide octahedra. There are three primary polymorphs: lizardite (platy), antigorite (corrugated) and chrysotile (coiled, fibrous). The anisotropic nature and non-spherical morphology of serpentine particles leads to complex rheology. Suspensions of serpentine minerals, especially those of chrysotile, exhibit high viscosity and yield stress, which can have a negative effect on comminution, flotation and dewatering operations. In flotation, serpentine is known to slime-coat pentlandite, a valuable nickel mineral, and form bubble-fibre aggregates that report to the froth, reducing nickel concentrate grade and recovery. Methods used to counteract the effects of serpentine in processing include desliming, the addition of chemical dispersants, salts or acid, and dilution (Bobicki et al., 2014a). Microwave pre-treatment has been proposed as an alternative way to eliminate the deleterious effects of serpentine in ultramafic nickel ore processing by converting the serpentine to olivine via dehydroxylation, which occurs at 600-700oC (Reaction 1). Olivine is isotropic, consisting of isolated silica tetrahedra linked by octahedrally coordinated magnesium ions, and has the same surface potential as pentlandite at the pH of flotation (~pH 9). Furthermore, since olivine is more reactive to CO2 than serpentine, microwave pre-treatment creates an opportunity to store more CO2 in tailings, an attractive option for mining operations looking to increase their bottom line where carbon pricing exists."

Jan 1, 2018

By Weiran Zuo, Narayan Krishnan, Frédéric von der Weid, Emmy Manlapig, Fengnian Shi, Klaas van der Wielen

Laboratory study has identified a new application of high voltage electrical pulse technology for pre-weakening ores. In recent years, the Julius Kruttschnitt Mineral Research Centre (JKMRC), Newcrest Mining and SELFRAG AG have conducted joint research in validation of pre-weakening of SAG mill feed through the pilot scale tests and comminution circuit simulations. Ten tons of SAG mill feed with a top particle size 150 mm were tested with two pilot scale SELFRAG machines installed in Switzerland. A simulation study using JKSimMet software was carried out to find where the high voltage pulses pre-weakening technique can be best applied in a gold-copper ore comminution circuit, based on the data of the pilot scale SELFRAG tests. A novel comminution circuit was designed, which incorporated SELFRAG to pre-condition part of SAG mill feed (9.5 to 150 mm) and to treat the circulating SAG mill pebbles. The high voltage pulse technology effectively reduced the amount of ‘critical size’ particles in the SAG mill and pre-weakened particle strength for grinding. Attributing to the nature of bi-modal size distribution and the significantly reduced F80, the simulations showed that the SAG mill had spare capacity to process part of hydrocyclone underflow from the secondary ball mill grinding circuit. The simulations indicated that the novel comminution circuit had the potential to remove two MP1000 pebble crushers and one 10 MW ball mill from the existing 2000 t/h grinding circuit. A 5 kWh/t energy reduction by adopting the novel comminution circuit in a gold-copper operation may be realized. This would result in substantial savings in operation costs.

Jan 1, 2014

By S. Banisi, A. R. Hasankhoei, A. R. Ghasemi, E. Razi, G. A. Parsapour

At the pelletizing plant of the Gol-E-Gohar mining and industrial company two parallel dry closed grinding circuits, each with the average throughput of 300 t/h, are used. Each grinding circuit consists of a burner, a dry ball mill (6.2 m×13 m) and an air separator. The ball mill consists of a 2 m-long drying and an 11 m-long grinding chambers. The iron ore concentrate is fed to the drying chamber by a feed chute. The first 1.35 m of the drying chamber consists of 56 flights in two rows to decrease the feed moisture from 5% to below 0.2% and the rest of dryer chamber consists of deflectors to pass the material to the grinding chamber. It was found that when the feed moisture content increased from 1.3% to 3.5%, the throughput decreased by 12% (35 t/h) indicating a low performance of the dryer. Monitoring the wear rate of flights for a period of 12 months showed that the first 0.8 m length of the flights length did not experience any wear. This means that about 59% of flights do not contribute in material distribution and drying. A DEM simulation of feed chute and the drying chamber demonstrated that due to the inappropriate design of feed chute most of materials do not get in touch with the first 0.8 m length of the drying chamber. To overcome this problem, various feed chute designs with different geometries were simulated by the KMPCDEM© software. With the aim of arriving at a proper material trajectory, where the total length of the flights are used, a new feed chute was selected. The simulation results indicated that if the height of the flights is increased from 1.60 to 2.26 m and the slope is increased from 45 to 48 degrees the material arrive at the first 0.48 m of drying chamber. In this manner, the unused part of the drying chamber decreases from 59% to 36% of the length. After installation of the new feed chute, during a period of three months the throughput increased by 36 t/h.

Jan 1, 2018

By M. Lak, M. Asghari, M. Saghaeian, R. Hejazi, A. Haratian

"Magnetic separation techniques are used extensively in mineral processing operations. Magnetic separators are robust and relatively easy to operate. As the ore get hard and low grade, fine grinding must be required mostly to allow for a high degree of mineral liberation. These processes encounter the magnetic separation process difficulty due to a significant change in the separation behavior of particles. This study investigates the effectiveness of a novel proven wet magnetic separator for the beneficiation of Lebedinsky (Russia) iron ore achieved through developing pole arrangement and tank design. Basis on the results of multiphasic simulation of a medium intensity magnetic separator (MIMS) and dense media tank using Magnetic Design Software, a new model of the MIMS separator was developed. The main of the new MIMS separator was focused on improving separation and the decreasing the number of separators in cobber stage of the plant. The new MIMS separator was tested into a pilot plant on the received samples from Lebedinsky iron ore plant. In addition to the basis on the results of the modeling, promising results of test work and previous experiences, it was claimed the unit capacity of new separator is 33.33% more than the existing separator that could decrease the number of separators. In addition, the significant energy saving in the same operational condition could be obtained without any important adverse effect on the final concentrate quality.INTRODUCTION Magnetic separation is a long-established method for the purification and removal of substances from fluids (Augusto et al., 1999; Buck et al., 2015; Hoffmann et al., 2002; Lauda et al., 2016; Lindner et al., 2010; Podoynitsyn et al., 2016; Rashidi et al., 2016), mainly in mining processing industries ranging from steel production to coal desulfurization as commercial technology (Andres, 1994; Augusto, 2002; Svoboda, 1987). High gradient magnetic separation as an effective method for recovering of weak and fine magnetic particles separation has undergone dramatic developments, and has also achieved extensive application during this time (Svoboda and Jujita, 1987). Magnetic separation operations can be categorized into high intensity as electrical (up to 20,000 gauss), Medium intensity (2000-5000 gauss) and low intensity (less than 2000 gauss) techniques. Magnetic separators offer a simple, clean and economic way to sort magnetizable ores and minerals. After pulverization, the material is run through an inhomogeneous magnetic field, where particles of different susceptibility experience different magnetic forces. The force increases with susceptibility, magnetic field and field gradient (Jongst et al., 1984).In magnetic separation, the difference in the susceptibilities of the various particulate materials is used to separate the material flow into two or more products (Wasmuth and Unkelbach, 1991). The magnetic force acting on a particle can be calculated using the following equation:"

Jan 1, 2018

By Z. G. Li

The large-scale vibrating screen has been applied widely in coal industry and other industrial areas as a kind of important device. As vibration mechanical device, it works very hardly and works in very bad environment so that the structure of screen is damaged easily. Therefore, it is very important that how to detect the fault of structure as early as possible to make the repair schedule reasonably and economically and to avoid the body hurt and device damage. As a kind of important structure of vibrating screen, the lower crossbeam is the main carrying structure and it is easily damaged, so it is regarded as a researched object in this thesis and it is tested under the load in the laboratory. Based on the test, acoustic emission wave signals can be got-ten by modern acoustic emission testing technique. Then, the ?wavelet packet - energy? from the characteristics of acquiring signals is used as neural network input vector. In the BP network structure design, the design of a hidden layer with variable number of BP network is established. Based on the error by contrast, the best nerve number can be identified in the hidden layer. Through integrated analysis, using Levenberg-Marquard BP study algorithm, network-training errors are relatively small, the acoustic emission signal is used in BP neural network as a pattern of recognition. In Matlab6.5, neural network model identification is created and taking advantage of nonlinearity and the ability of learning and memory of Neural Network, this model is fixed by training structure of network with training samples. The work presented shows that acoustical emission signal processing and research on early fatigue fault diagnosis based on the wavelet and the neural network is viable.

Jan 1, 2014

By S. Koca

Vast amount of fly ash, bottom ash and slags, are produced each year due to coal combustion in thermal power plants. These products consist of mainly unburned carbon and inorganic compound (such as: silica, alumina, iron oxides, magnesium oxide, phosphorus oxide etc.). These are valuable minerals and can be recycled or recovered if properly processed. One third of the material find application as an ingredient in cement and other construction products, the rest is held in dams or similar dumps, which results in a hazardous impact on the environment, polluting soil and ground water. The unproductive use of land, the associated long term financial burden maintenance and negative environmental impacts have led to realization that alternative uses for combustion by-products as a value added product beyond incorporation in construction materials are needed. At present, there is an intensive search to increase their uses. Other uses of coal combustion residues include as raw material in brick and ceramic tile fabrication, as filler in plastics and paints, extraction of valuable mineral materials, production of zeolites and soil and mine waste treatments. Separation of unburned carbon from bottom ashes by means of flotation was conducted in order to increase the possibility of the recycling of coal combustion wastes. In the flotation experiments collector, dispersant and frother amount, pulp density and pH were tested as variables. After first stage flotation experiments, at optimum conditions, the carbon content was reduced down to 5.58 % in the tailings fraction. This fraction meets the industrial specifications and can be utilized as a cement additive. At the same conditions the carbon content of the concentrate increased to 44.72 % at a carbon recovery of 65.81 %. After the cleaner stage flotation experiment the carbon content of the product is enhanced to 62.53 %. This fraction can be blended back into the coal feed to the power plant boilers.

Jan 1, 2014

By K. C. Corin, M. S. Manono, R. M. Manenzhe, J. G. Wiese

"Environmental concerns necessitate the recycling of process water within mining operations. Given that recycled water is chemically different from fresh water, and collectors are added such that they adsorb at the liquid-particle interface, changes in the aqueous phase are expected to affect collector adsorption. A Finnish nickel-copper ore was floated in synthetic plant waters of varying ionic strengths and plant waters obtained at Boliden Kevitsa Mine, with aerophine and sodium isopropyl xanthate as collectors. Of the tested waters, the copper thickener overflow was the least conducive to xanthate adsorption and valuable mineral recovery. The nickel thickener overflow, standard process water, and raw water were the most conducive to xanthate adsorption. For the raw water and nickel thickener overflow, increased adsorption correlated with increased valuable mineral recovery. Further, recycling xanthate retained in water affected the selectivity of the collector and hence the concentrate grades.INTRODUCTIONFlotation is a separation process that exploits the differences in the surface properties of the particles being separated. The efficiency of separation is dependent on the degree of hydrophobicity achieved by the particles meant to be floated, which are, in most cases, valuable minerals. The hydrophobicity is in turn dependent on the adsorption of the chosen collector onto the surfaces of the floated particles (Fuerstenau, 1984; Taggart and Hassialis, 1946). Empirical findings suggest that species dissolved in solution strongly influence collector adsorption and overall flotation response (Fuerstenau and Chander, 1986). Due to environmental concerns, it is becoming more pertinent for mining plants to recycle process water and hence limit the usage of potable water. There is an interest to ensure minimal discharge of plant water into the environment, as this water is typically polluted with process reagents that may render it toxic (Levay et al., 2001)."

Jan 1, 2018