Search Documents

By Li Huimin

In this paper the step of determining the property index and the program of mixture ratio design of stabilizing agent in deep foundation construction are presented. According to the principle of computer simulation, the model and the method of computer simulation for optimum mix design are set up. Also, the precision of simulation results has been estimated and verified experimentally.

Jan 1, 1991

By George G. Goble

The use of augercast piles has been limited by the engineer's concern for the structural quality of the installed pile. The nature of the pile is such that its final structural continuity is very dependent on the skill of the personnel that do the installation. Thus, NDT methods have been used to verify integrity and when problems are indicated the available solutions are usually quite costly. If information were available during the pile installation so that immediate steps could be taken to correct perceived problems, the concerns of the engineer could be addressed and the system would gain increased reliability. Pile Dynamics, Inc. has developed a quality control system, the Pile Installation Recorder for Augered Cast-in-Place piles (PIR CFA). This system consists of the following devices as shown in Figure 1. 1) The Control Unit powers the sensors, conditions the signals from the sensors, records all measurements, takes input information from the operator, displays the results, and stores the recorded data on a flash card for later permanent storage and processing. During the use of the system all of the results obtained during a test are seen during recording and can be reviewed on the screen again after completion of the installation. The ability to review the measured information makes it unnecessary to print a copy in the field. Since printers often give difficulty in the construction site environment the ability to review the results quickly after completion of the installation is an important capability.

Jan 1, 1997

By Bora Okumusoglu, Devon K. V. Mothersille

"AnchorTest is an innovative software package, specifically developed for tablets, that permits ground anchor test data assessment and management in real time. The solution has two components: a front-end tablet app runs on the Apple iPad platform, and a back-end Cloudbased system running on Amazon Web Services with an online cross-platform website, which can be accessed from any PC, tablet or even mobile smartphone. This tool provides full data analysis and data management capabilities and portability to create greater efficiency in the anchor testing process. AnchorTest is programmed to accommodate the major international anchor testing codes and incorporates an intuitive user interface, which is revolutionary compared to conventional engineering software designs. The use of this tool creates an environment where the testing of ground anchors has effectively become a paperless exercise with greater efficiency and access to instantaneous feedback on the performance of anchors in relation to established acceptance criteria.Historically, project personnel record and analyze the results from anchor load tests using spreadsheets and a laptop computer and/or on predesigned paperbased test sheets (usually as a backup of the testing). In addition, the processing of the test results is not typically performed in real time as the testing progresses — the calculations and analysis are performed either afterward while still on site (if a field office is available) or after returning to the office. Undoubtedly, on larger projects containing numerous anchors where multiple anchor tests may be performed at the same time, processing, analyzing and accepting the load test data and results can be especially time consuming, which could cause delays to the construction schedule.DevelopmentThe need for a more automated and digitized approach to record, process and analyze the data from anchor load tests was highlighted at a deep basement project for a mixed-use development complex in Moscow, Russia. The diaphragm wall supporting the structure was approximately 1,970 ft (600 m) in perimeter length and about 148 ft (45 m) deep, with an excavated depth of about 82 ft (25 m), which required six levels of single bore multiple anchors (SBMAs). This project provided a challenge to recording, processing and signing off on the data generated from some 3,600 3-unit SBMAs. More specifically, for this project, three hydraulically synchronized stressing jacks were used to stress and proof test each 3-unit SBMA, which resulted in nearly 10,800 data plots of the load-extension tests being generated. This project served as the main impetus in the conceptual design and optimization of AnchorTest."

Jan 1, 2017

By Per Eriksson

For light buildings on clay, foundations on L/C-columns is in many cases a competitive alternative to piles when the thickness of the clay is moderate (<20 m). The method is applicable for the above mentioned depth when the clay is normally consolidated, and for thicker deposits when the clay is overconsolidated at depth. This case study concerns a shopping mall in Nordby, Sweden, founded on L/C-columns (5-15 m in length) and generally spaced 1.45-2.0 m (spacing 0.7 m was used below pillars). The base slab was built as a raft foundation, using fibre reinforced concrete.

Jan 1, 2000

By Patrick J. Hannigan

A comparison of 40 statically and dynamically load tested piles was performed to evaluate the variation between testing methods. This evaluation indicated an agreement of 10% to 15% could be obtained when the available static resistance is fully mobilized by both methods and when time dependent capacity changes are minimized. Dynamic pile testing recommendations for minimum induced impact force, ram weight to pile weight ratio, and considerations for time dependent capacity changes are presented.

Jan 1, 1987

By Charles H. Dowding

Whenever piling vibrations are significant, construction activities associated with pile driving and/or excavation can produce permanent displacement. These permanent displacements are more detrimental to structural performance than the hair sized, cosmetic, plaster cracks that might be produced by slightly exceeding reasonable vibration controls. Case studies are presented which demonstrate the relative importance of permanent displacements compared to directly produced transient vibration displacement within a horizontal distance of one pile length. Special attention is paid to settlements produced by densification of liquefiable sands. SOURCES OF TRANSIENT AND PERMANENT DEFORMATION DURING CONSTRUCTION Confusion over multiple sources of facility deformation caused by adjacent construction complicates the discussion of the relative importance of vibration induced cracking. None of the recent scientific investigations of vibration induced cracking (Siskind et el, 1980), involved deformation other than that produced by ground vibration from rock blasting. Thus these studies carry the implicit assumption that no ground deformation occurred other than that produced by the transient vibration. In other words there is no permanent deformation other than that which is typical of the older residential structures investigated.

Jan 1, 1991

By George Koenig

I have been granted the outstanding privilege... and pleasure to introduce you this evening to the Grand-Duchy of Luxembourg and to tell you in a few words how this country came into existence, how it managed to survive and what role it nowadays plays in the International Community. Luxembourg, situated between Belgium, Germany and Prance is a small, a very small country... just a dot on a map. After all, it is only a matter of 62 miles from top to bottom and 37 miles across at it&apos;s widest... barely covering some thousand square miles... so be careful about stepping on the accelerator... you might be in and out without having realized it... which would be a real shame as the Grand-Duchy enjoys a fairly unique geographical feature in so far as it provides the visitor with an outstanding variety of scenery concentrated in a minute spot.

Jan 1, 1987

By Pierre Gouvin, Michael Oakland

"This paper covers the rapid response methods used to monitor the emergency response to damage to an historic structure. An architectural gem, the latest incarnation of the old south Church was completed in 1875, utilizing local conglomerate (pudding stone), combined with brownstone and other materials to make an incredible showcase for priceless stained glass and other details epitomizing the height of the American Industrial Revolution. As part of required American with Disabilities retrofits to the adjacent Metropolitan Boston Transit Authority Station (MBTA), a support of excavation system was implemented with tradition sheet piles. During excavation (SOE) it was determined that Jet Grouting would need to supplement the sheeting to close openings in the SOE. During Jet Grouting, the eastern side of the structure was bisected, and lifted over 2 inches up and to the south. The movement occurred rapidly, within minutes, and subsided when Jet grouting was discontinued. The paper will describe the nature of the immediate response to get a real time monitoring program established, and the follow on monitoring program that ensued to provide the needed information to the stakeholders about this critical structure to evaluate stability, safety and to develop a long term remediation plan. The real time systems and instruments used consisted of Automated Motorized Total Stations (AMTS) and Automated Crackmeters. The Paper will describe the techniques used to control construction in safe manner.INTRODUCTIONThe Old South Church of Boston was constructed in 1875 and is one of the best examples of High Victorian Gothic Architecture in the Northeast. (Fig. 1) shows the newly constructed Old South in 1882. The Roxbury Conglomerate used to construct the church combined with large stained glass window by Clayton and Bell of London provides its unique appearance. Like most of the structures constructed in Boston’s Back Bay at that time, the church is founded on timber piles which penetrate the fill and organic soils to bear in the upper Boston Blue Clay. The churches interior includes high vaulted plaster ceilings and a 1920’s E. M. Skinner organ with exposed pipes as long as 32 ft. in length. The Church was added to the list of National Historic Landmarks in 1970 and is a featured Boston attraction."

Jan 1, 2017

By O&apos, M. W. Neill

Mini-piles have been found to be a practical, technically correct remedial underpinning method. They can be constructed in limited access areas with very little disruption. Experience indicated that mini-piles installed using a down-the-hole soil displacement hammer would be particularly effective in the "bottomless" Beaumont Clay formations in the Houston, Texas, U.S.A. area. The University of Houston Foundation Testing Facility was ideally suited to perform tests on mini-piles. The availability of extensive geotechnical data and previous pile test results was invaluable in evaluating the mini-pile test data. As expected, the mini-pile test results were consistant with test results from large sized driven piles in the same soil formation.

Jan 1, 1989

By Rick Ellman, Ian Chaney

"The Hampton Roads area encompassing the Norfolk, Virginia Beach and Newport News metropolitan region experiences some of the worst traffic congestion in Virginia. With continued growth of the ports and increasing demand, the Virginia Department of Transportation (VDOT) initiated the Downtown Tunnel/Midtown Tunnel/MLK Expressway Project, a complex undertaking critical to addressing the Hampton Roads area’s transportation needs. The project is a $2.1 billion Design/Build/Finance/Operate (DBFO) endeavor most notably involving the construction of a new two-lane vehicular tunnel utilizing the Immersed Tube Tunnel (ITT) method. The tunnel will pass under the Elizabeth River parallel to the existing Midtown Tunnel between Norfolk and Portsmouth, Va. It will be the largest design-build project constructed in the history of the Hampton Roads District.The New Midtown Tunnel will extend approximately 6,450 ft (1,966 m) along the north side of the existing tunnel where it ties into the existing Midtown Tunnel approaches in Norfolk and Portsmouth. It is being installed in a pre-excavated trench of which approximately 2,250 ft (686 m) required bracing on the Portsmouth side and approximately 1,000 ft (305 m) required bracing on the Norfolk side. The remaining 3,200 ft (975 m) of trench excavation was open cut dredging with laid back side slopes, optimized to reduce dredging, disposal and backfill quantities while also reducing the risk to the existing tunnel. The braced excavation portions of the tunnel alignment were divided into distinct segments which include: Portsmouth Approach Boat Section, Portsmouth Approach Cut-and-Cover Section, Portsmouth Dredge Section, Norfolk Dredge Section, Norfolk Approach Cut-and- Cover Section and the Norfolk Approach Boat Section. All “approach” excavations were performed in the dry and all “dredge” excavations were performed in the wet. Eleven ITT segments are being fabricated in the Sparrows Point Dry Dock facility in Baltimore, Md., and each 14,000 ton (12,700 tonne) segment is being towed approximately 220 mi (354 km) to the site. The ITT segments will extend under the Elizabeth River, with the deepest crossing 90 ft (27 m) at the Federal Navigation Channel. Once beyond the channel limits the ITT rises at an approximate 4.5% slope. Controlled screeding and element lowering operations will be performed primarily from floating barges."

Jan 1, 2014

By Arunsiva R., Sivaranan S., Venugopal B., Kumaran M.

Being a rapidly developing country, India is undergoing a massive infrastructure phase change remarkably. The construction industry is already set to boom, but the time and space constraints necessitate the employment of heavy plants and machinery to take the foundations deeper than ever. Operating such machinery on soft or poor ground conditions without a good working platform leads to uncertainties with massive loss of men and machinery. Plenty of such cases can be observed on construction sites across the globe. Unfortunately, forming a temporary working platform is given least to no importance in the construction industry, particularly ground engineering. This glitch can only be addressed through standard guidelines or codal recommendations on designing and implementing temporary working platforms issued by regulatory bodies. The present paper highlights the importance of providing the working platform, existing design method for working platforms such as TWf 2019:02 of Temporary Works forum, Building Research Establishment BR470 and a brief discussion on the design and construction of the geosynthetic reinforced working platform with a case study is also included. A pitch has been made on the importance of Indian codes/guidelines for the design and construction of temporary working platforms. These guidelines will ensure the safety of the men and heavy machinery and, in addition, increase the productivity of foundation construction irrespective of weather conditions and also become part of the regular construction scope.

Sep 1, 2022

By J. Osterberg

A new device has been developed for load testing driven piles and drilled shafts which consists of an hydraulic jack or bellows which has a telltale rod fastended to the bottom. The rod extends upward to the surface through a pressure pipe. When pressure is applied, the jack or bellows expands, applying an equal upward and downward load at the bottom. The downward movement at the bottom is indicated by the rod and the upward movement is indicated by the movement at the top. Thus, upward and downward load-deflection curves can be drawn. As load increases, failure will occur either in end bearing or friction. Results of field installations are described. Total loads of up to 1,100 tons metric have been used. The method obviates the need for the reaction load required for the conventional pile loading test and separates friction and end bearing. It is especially advantageous for use over water, in crowded spaces and for inclined piles.

Jan 1, 1989

By Patrick Bermingham

This report presents the results of six STATNAMIC loading tests that were carried out on four different pile types at the CALTRANS 280 Test Site (Bridge No. 34-46) in conjunction with the Tension Pile Test Program. The STATNAMIC testing was performed by Berminghammer Corporation at the request of the California Department of Transportation, Office of Geotechnical Engineering. Others performed the static tension (uplift) and compression loading tests which werecarried out on the piles tested using the STATNAMIC method. A summary of the STATNAMIC test results is presented and discussed, and the appropriate results are compared with the static test results

Jan 1, 1993

By Anil Bhandari

Using subsurface data collected at each drilled shaft location is an ideal approach for conducting drilled shaft design. However, conducting subsurface tests at each drilled shaft location and subsequently performing the drilled shaft design can be a daunting task for a noise barrier wall that is divided into six (6) sections and stretches for approximately four (4) miles. In addition, having individual drilled shaft designs complicates the construction process. Grouping the subsurface conditions into broad categories and performing the design for each of those categories is an attractive alternative to the design per boring approach. Currently there are no existing guidelines to aid a designer on grouping the subsurface conditions for the drilled shaft design for the noise barrier walls. Therefore, a method was developed based on the Standard Penetration Test (SPT) N values of the near surface soils to categorize the soil profiles into distinct categories. Since the soil engineering properties of the near surface soils are known to be critical for drilled shaft lateral capacity, these soils were emphasized in the methodology. This method was successfully implemented for the design of drilled shafts supporting the noise barrier walls along the I-20 in Columbia, SC. For this project, two distinct soil profiles, labeled as ?strong? and ?weak?, were used. An overview of the soil profile grouping methodology is presented as well as the vertical and lateral drilled shaft capacity analyses for this project for the two general soil profiles. The analyses indicated that the axial capacity governed the design in the ?weak? soil profile and the lateral capacity controlled the design in the ?strong? soil profile. However, this is not a generalization and whether the axial or the lateral capacity governs the design of drilled shaft depends on the soil profile and design loads. Nonetheless, our findings emphasize that both lateral and axial capacity should be checked for drilled shaft design even when the vertical load are minor.

Jan 1, 2011

By Zia Zafir

Design of the deep foundations for the loads imposed by lateral spread include the estimate of the pressure applied by the liquefied material as well as amount of anticipated displacement. In the absence of a non-liquefiable cover over a liquefiable layer, it is possible to design the foundation system just for the additional pressure applied by the flow slides. On the other hand, if a non-liquefiable layer exists above the liquefied zone, the foundation should be designed for anticipated movements. To completely account for liquefaction and/or lateral spread and their interaction with the deep foundation system, a coupled soil-structure interaction (SSI) analysis should be performed. However, a complete SSI analysis may not be feasible for most of the projects. This paper will present recent advances in analysis techniques and simplified methods to design deep foundations for liquefaction and lateral spreading. In addition, a case history of the Rancho California Bridge in southern California located within 1 km of the active Elsinore fault will be presented. One of the bridge abutments is underlain by potentially liquefiable layers. The pressure applied by the liquefiable layer was estimated to be greater than the shear capacity of the 36-inch CIDH piles designed for the abutment. However, with limited ground improvement and more careful analyses incorporating structural effects of CIDH piles, resulting design and construction resulted in a factor of safety greater than 1 against slope failure. The recommended approach was generally consistent with the recently published, and AASHTO sponsored, NCHRP 12-49 project regarding seismic design guidelines for new bridges and the effects of seismic displacements against bridge foundations.

Jan 1, 2006

By Karl A. H iggins, James P. Racine

"Displacement Cast-in-Place (DCIP) piles are not a common deep foundation type in the Washington, DC Metro Area market. As a result, less regional data is available for these foundations compared to other alternate deep foundation types. Displacement cast-in-place piles (DCIP) differ from traditional Auger Cast-In-Place (ACIP) piles in that the pile annulus is formed by pushing a partially-flighted, auger bit to depth via a large mandrel. The auger bit includes a displacing body near the bottom of the tooling. Therefore, little to no spoils are generated during installation and the soil around the annulus is largely densified in-place due to the displacing body being slightly larger than the mandrel it is attached to.Due to this densification, one would expect that the theoretical DCIP capacities (compression or tension) would be greater than an ACIP pile (assuming a pile of similar length and diameter). After 20 static load tests and the installation of over 6,000+ piles on the MGM National Harbor Casino Project, the differences in pile support characteristics between DCIP and ACIP piles of same size and depth was small. The performance of both pile types depended on the density and type of soil within the bearing stratum. In some early cases of DCIP use, the performance exceeded expectations and appeared to be more in line (or better) than typical capacities obtained from driven displacement piles. Other times, the tip elevations could not be achieved or were so difficult to achieve that installation delays occurred and/or significant additional engineering effort was required to address piles short of their requirement embedment.This paper will discuss the limitations of DCIP pile installation in dense Coastal Plain soils and will present the lessons learned during this project. The paper will also compare the DCIP pile type to both conventional ACIP and driven displacement piles utilizing regional and site-specific load test and installation data."

Jan 1, 2017

By Gary Kuhns

Central Florida is among the fastest growing urban areas in the United States, and its rapid development has required the steady construction of various types of civil engineering works. The karst geologic terrain and variable geotechnical conditions, however, present special challenges to the design and construction of deep foundations. The subsurface profile can be idealized as a surficial layer of Pleistocene sands, underlain by the highly variable Miocene-age Hawthorn Group, consisting of various combinations of sand, silt, clay, phosphate and highly weathered limestone. The Hawthorn Group is underlain by Eocene-age limestone that comprises the Floridan aquifer. Vast networks of solution cavities are present throughout the Eocene limestone, sometimes allowing downward raveling of the overlying soils and the creation of sinkholes. In some cases, the relic sinkholes can be filled with soft compressible organic soils extending to depths greater than 100 feet (30.5 m). Driven piles are frequently employed as a deep foundation alternative, although occasionally cast-in-place piles/shafts have also been used. Piles are often driven for bearing in the weathered limestone within the Hawthorn Group, but are sometimes installed as friction piles in the upper soil and intermediate geomaterials. Dynamic pile testing is routinely performed during pre-construction test pile programs, or during production for quality control and assurance purposes. This paper presents discussions on the design and construction aspects of deep foundations unique to Central Florida subsurface conditions and local practice. Foundation issues such as subsurface variability, soil setup, pile damage, negative skin friction, and sinkhole conditions are discussed with the aid of demonstrative case histories.

Jan 1, 2003

By K. Viking

This article deals with some of the civil engineering related problems to be encountered when offshore wind energy projects transform from prototype offshore wind energy converter farms, developed and installed during the 1990&apos;s, to commercial farms that&apos;s currently planned to be built. The offshore wind energy converter (OWEC) installations encounter a wide range of problems, only partial of these are geotechnical. In Europe both onshore and offshore wind farms have, from a historical point of view, usually been founded by using the monopole technique, installed with traditional impact hammers, or by using gravitational foundations. However, the rapid development of bigger turbines and larger wind farms, together with increasing considerations of fatigue aspects, has lead to financial benefits of developing and exploring other foundation techniques. This paper reviews some Scandinavian experiences regarding critical components of the design phase in relation to connecting the superstructure to the ground, and some of the main considerations of how the loads applied to the structure are transferred to the surrounding soil. Keywords: Offshore Wind Turbines, Wind Farms, Foundation, Pile, Gravity Structures

Jan 1, 2005

By Makoto Kimura

Failure tests on laterally loaded single and pile group are analyzed with a 3-dimensional elasto-plastic finite element program. In the analysis, the mechanical behavior of the ground is supposed to be elasto-perfect plastic with Drucker-Prager&apos;s yielding criterion. The nonlinearity of the piles is simulated by assuming a hyperbolic relation between the bending moment and the curvature of the piles. The influence of the axial stress on the cast-in-place concrete piles is also considered in the numerical analysis. It is found that the mechanical behavior of the piles subjected to lateral loading, such as the load-displacement relation up to an ultimately large deformation, and the distribution of bending moment in the pile group can be well simulated.

Jan 1, 1996

Jan 1, 1998