Search Documents

By Saieb Haddad, Henry Pate

"Building retaining walls in an urban area is becoming more difficult due to right-of-way restraints. Using standard concrete cantilever walls requires a construction easement behind the walls for installation, which for the most part is unavailable. To install these types of walls in a limited right-of-way requires extensive temporary walls to minimize the construction easement. Top-down construction walls utilizingtie-back anchors for support require either the purchase of the right-of-way or underground easements in the area of the anchors.These problems faced the Department on Interstate 75 widening in Knoxville, TN in an area of a large cut. A multi-story Insurance Building and a large commercial Retail Center were located at the top of the cut. To prevent any impact on the buildings, the walls had to be placed within a limited area. The option of buying the properties was prohibitively expensive. Due to the height of the two walls and the variability of the underling rock line, contiguous caisson pile cantilever walls were contemplated as the only wall type that would be appropriate. The cost of the two walls was estimated to be very close or even higher than the cost of purchasing the two buildings. The Department believed that there must be a better way to deal with the problem. A vertically tied-down pile frame wall constructed from the top-down with a concrete facing was developed. This allowed the construction of the walls to be restricted to the available limited area and provided substantial savings for the State.INTRODUCTIONThe widening of I-40/75 has been a major transportation project in the Knoxville area which is being constructed by the Tennessee Department of Transportation. The project includes 18 Retaining Walls and 13 Bridges.Two of the 18 Retaining Walls, refer to Figure 1, are to support two valuable properties, one being an insurance company housed in a multi-story office building and the other a suburban shopping center which were appraised at $13.0 million and $5.0 million respectively. Due to the 31 ft. (9.5m) maximum height of each of the two Retaining Walls and the limited Right-of- Way of 15.0 feet (4.6m), a contiguous caisson pile cantilever wall was proposed for each of the two retaining wall sites with an estimated cost of $12.0 million each. The contiguous pile cantilever Wall is comprised of a line of caisson piles socketed into underlying competent bedrock. The design required that 4 ft. (1219mm) dia. piles be installed at 6 ft. (1.83m) centers, socketed into rock in order to provide lateral stability and restrict lateral wall movement to acceptable limits. The line of caissons would be fronted with a cast-in-place concrete face wall"

Jan 1, 2007

By Saieb Haddad, Henry Pate

"Building retaining walls in an urban area is becoming more diffi cult due to right-of-way restraints. Using standard concrete cantilever walls requires a construction easement behind the walls for installation, which for the most part is unavailable. To install these types of walls in a limited right-of-way requires extensive temporary walls to minimize the construction easement. Top-down construction walls utilizing tie-back anchors for support require either the purchase of the right-of-way or underground easements in the area of the anchors.These problems faced the Department on Interstate 75 widening in Knoxville, TN in an area of a large cut. A multi-story Insurance Building and a large commercial Retail Center were located at the top of the cut. To prevent any impact on the buildings, the walls had to be placed within a limited area. The option of buying the properties was prohibitively expensive. Due to the height of the two walls and the variability of the underling rock line, contiguous caisson pile cantilever walls were contemplated as the only wall type that would be appropriate. The cost of the two walls was estimated to be very close or even higher than the cost of purchasing the two buildings. The Department believed that there must be a better way to deal with the problem. A vertically tied-down pile frame wall constructed from the top-down with a concrete facing was developed. This allowed the construction of the walls to be restricted to the available limited area and provided substantial savings for the State. INTRODUCTIONThe widening of I-40/75 has been a major transportation project in the Knoxville area which is being constructed by the Tennessee Department of Transportation. The project includes 18 Retaining Walls and 13 Bridges. Two of the 18 Retaining Walls, refer to Figure 1, are to support two valuable properties, one being an insurance company housed in a multi-story offi ce building and the other a suburban shopping center which were appraised at $13.0 million and $5.0 million respectively. Due to the 31 ft. (9.5m) maximum height of each of the two Retaining Walls and the limited Right-of- Way of 15.0 feet (4.6m), a contiguous caisson pile cantilever wall was proposed for each of the two retaining wall sites with an estimated cost of $12.0 million each. The contiguous pile cantilever Wall is comprised of a line of caisson piles socketed into underlying competent bedrock. The design required that 4 ft. (1219mm) dia. piles be installed at 6 ft. (1.83m) centers, socketed into rock in order to provide lateral stability and restrict lateral wall movement to acceptable limits. The line of caissons would be fronted with a cast-in-place concrete face wall."

Jan 1, 2007

By R. A. Fraser

Large diameter (1.0 to 2.5m) bored piles have been widely used to support buildings and elevated roadways in Hong Kong. Most of these piles are founded on a hard bearing stratum such as granitic or volcanic bedrock, in the newly reclaimed areas along the water-front, the bedrock stratum can be as deep as 70-80 metres below ground surface, and construction of bored piles to bedrock in this case is difficult and unjustified. Nevertheless, Building Ordinance Regulations in Hong Kong require piles to be founded on bedrock. To overcome this problem for elevated roadways, trial piles have been designed founded on dense, completely decomposed granite. A number of piles have been constructed and subsequently load-tested to allow the rate of mobilisation of skin friction to be measured. This paper outlines the design, construction and testing method, and comments on the test results from several trial piles. GEOLOCICAL CONDITIONS The geology of Hong Kong consists predominantly of acid volcanic rocks intruded by granite. The granite has been deeply weathered, and variations in sea level have produced a drowned coastline with sequences of alluvial, colluvial and marine deposits overlying the weathered bedrock. Reclamation has extended this coastline. Typical site conditions are described later in the paper.

Jan 1, 2010

By Bernhard Bruggaier

Outside the oil and gas industry there is an increasing demand to install big piles for the foundation of ports, bridges, and wind-energy plants. This article introduces the design and techniques in using large MENCK pile driving hammers to install big foundation piles. Piles with a length up to 120 m, an outside diameter of 1.0 m to 3.15 m and weighing between 25t and 400t are being driven for these types of foundations. The required energy lies between 200 and 1700 kNm. Pile driving hammers that bring this amount of energy weigh from 38 to 300t and have a length between 10 and 20 m. Handling these big pile driving hammers requires a crawler crane on land or cranes on floating pontoons or jack-ups when working in water. Possible are either vertical or inclined piles, using a leader for inclinations up to 1:1.7 or up to 1:3 in a free riding version. Project descriptions demonstrate the versatility and practical use of the equipment under diverse operating conditions.

Jan 1, 2002

By Abolfazl Eslami, Fatemeh Valikhah

"Complexity in soil-foundation interaction and subsoil nonlinear behavior cause difficulties and uncertainties in evaluating the actual values of foundation design factors such as settlement. The acquired continuous records of Cone Penetration Test (CPT) can be used to determine the soil profile and characteristics those are applicable in the geotechnical design. In this paper, it has been attempted to present a new non-linear stress-strain approach to estimate the foundations settlement by using CPT data in the form of soil behavior classification charts. This new approach is based on Janbu method (1960s and also 1998). Instead of using fixed and constant values for stress exponent (j) and modulus number (m), continuous coefficient variations can be used. The proposed approach also can be used as a new method to predict pile group settlement. A data bank has been compiled containing twenty-two practical case histories to investigate the accuracy of the predictions made by the proposed and available common methods. The comparisons indicate that the proposed approach is relatively able to predict the settlement close to their real values. Therefore, it can be considered as an alternative method based on valuable CPT data and nonlinear stress-strain approach for foundations and pile groups settlement estimation.INTRODUCTIONComplexity in soil behaviour for settlement analysis is the result of non-linear and time dependent stressstrain behaviour of soils, their elasto-plastic performance under loading and unloading situation and also effects of stress history (Holtz et al., 2011; Fellenius, 2015). Hence, many relations and equations have been proposed to predict foundation settlement, where most of them are based on typical different parameters such as soil stiffness (E), foundation width (B), contact pressure (q) and pressure developing in depth (Janbu, 1967 also 1998; Briaud and Gibbens, 1999; Uzielli and Mayne, 2012).The Janbu approach for settlement estimation, proposed by Janbu in the early 1960s, combines the basic principles of linear and non-linear stress-strain behaviour of material. The method is applied to all types of soils. The relation between stress and strain is a function of two non-dimensional parameters which are unique for any soil: a stress exponent, “j”, and a modulus number, “m”. The Janbu relations are derived from the definition of tangent modulus by the following expression:"

Jan 1, 2017

By Peter A. Thompson, Richard E. Prust

"The Bangkok Mass Rapid Transit (MRT} Chaleom Ratchamongkhon Line project is the first underground subway to be completed in Thailand. It consists of 22 km (14 miles) of twin-bored tunnels and 18 cut and cover stations constructed within the deltaic deposits that underlie the city. This paper describes the ground conditions, site investigation, including the use of the self-boring pressuremeter and the associated design issues for the construction of deep foundations. The paper also describes a selection of the various deep foundation solutions that were adopted to address particular constraints of the project and the ground conditions, including slurry walls for the cut and cover stations and foundations used for the underpinning of existing structures.INTRODUCTIONThe MRT Chaloem Ratchamongkhon Line Mass Transit Underground Railway comprises approximately 22 km (14 miles) of tunnels and 18 stations. The route is shown in Figure 1.The project was divided into two design and build contracts. The northern section was awarded to the ION joint venture, composed of Italian-Thai Development PLC, Obayashi Corporation and Nishimatsu Construction Co Ltd. Arup were contracted by ION for the design of the northern section. The section comprises 11 km (7 miles) of twin-bored tunnels, nine cut and cover station tunnels constructed within perimeter slurry walls using top down construction methods, and two cut and cover tunnel structures.The majority of the route of the northern contract follows existing highway Rights of Way. This results in the tunnel alignment passing through the foundations of existing highway bridge structures for which a variety of deep foundation solutions were adopted to underpin these structures.An 8-story park and ride building in the Lat Phrao area was also constructed using deep foundations."

Jan 1, 2005

By Allen Cadden

The type of soil we had was a silty fine sand. It had been placed by hydraulic methods in 1904 so it was quite clean I would say less than 10% silt the rest of it was very loose sand. That I'm not certain, I've only done it on sandy soils but it would stand to reason that some sort of a number should apply because you are measuring the amount of work that you are doing to it so if the soil is fairly consistent over the site it should be able to generalize from there but I don't know for a fact that it works. Well, verifying to ourselves that this method actually worked because we weren't certain at first when we were doing it so then we would develop the numbers and then check the results.

Feb 10, 2003

By William M. Camp

Construction-induced earthborn vibrations have long been recognized as a potential problem with respect to the constructed environment and various vibration criteria are in use to prevent damage. A special case of construction vibration control is the protection of early-age or ?green? concrete. Unlike limits for damage prevention to building stock, there is no rational, widely accepted limit for protection of early-age concrete. Numerous criteria have been proposed or reported in the literature and the most relevant and rational proposals are summarized herein. These findings are applied to a case history involving both bored and driven piles. Vibration measurements were made during pile driving activities and the vibration magnitude was evaluated with respect to the exposure of freshly-placed and curing concrete to the earthborn vibrations. The maximum vibration magnitude at the applicable distances from pile driving was on the order of 0.3 inches per second. Based on the most persuasive literature, threshold values of 0.8 inches per second or even 1 to 2 inches per second for the protection of green concrete appear to be well-supported. Consequently, it was concluded that the pile driving activities and bored pile construction could proceed simultaneously.

Jan 1, 2010

By Andrew Baxter

This paper focuses on the design of steel bearing plates to transfer load from tiebacks and tiedowns to a concrete mass. It lists and describes the various available procedures for design of bearing plates as well as explains the design procedure recommended by the authors, which incorporates the Post Tensioning Institute (PTI) recommendations. The paper includes a step-by-step design example following the recommended procedure that captures the most important aspects of plate design. The dimensions of the plate calculated from this example are compared to the design dimensions obtained from various other procedures, including those by American Association of State Highway and Transportation Officials (AASHTO) and VSL International, Ltd. (VSL). The paper also includes the results of numerical modeling of the plate that will help the reader understand important aspects of plate-concrete interaction. The authors envision that this paper will serve to create an understanding in the geo-industry of suitable design methods and help improve procurement of bearing plates for tiebacks and tiedowns.

By Scott A. Walker, Gabriel J. Alcantar, Brian Zuckerman, Ramin Golesorkhi

"The new San Francisco 49ers Levi’s Stadium is part of the next generation of sporting facilities. Constructed in Santa Clara, Calif., the new structure has 68,500 open-air bowl seats and includes a 7- story tower housing more than 150 suites. The overall project includes the stadium structure, elevated open pedestrian walkways, commercial community space, three new pedestrian bridges and improvements to the adjacent light rail station. Sustainable design for the project includes a green roof, photovoltaic panel and a ground source geothermal system. Stadium-wide next-generation Wi-Fi capability is another feature. The design-build project team included HNTB (project architect), Magnusson Klemencic Associates (MKA, structural designer) and a joint venture of Turner Construction and Devcon Construction (TDJV, general contractor).During preconstruction, the 49ers’ original design team and the design-build team formed later worked together to facilitate communication and provide continuity. This helped to meet the project’s aggressive schedule. Working directly for the 49ers, with the design-build team, Treadwell & Rollo (T&R) served as the geotechnical engineer of record for the project from preliminary to final design and through construction. Although not contracted directly to TDJV, the stadium ownership encouraged direct interaction between T&R and TDJV and improved responsiveness to geotechnical issues during design and construction.Subsurface ConditionsThe new stadium lies within the Santa Clara Valley, a deep alluviumfilled basin resulting from historic movement on the active and potentially active strike-slip and thrust faults that bind the valley. The valley is filled with Holocene age (approximately 11,000 years old to present) alluvium, consisting of levee and basin deposits, with bedrock more than 750 ft (229 m) beneath existing ground surface. The stadium site is between two of the highly-active faults in California, the Hayward Fault 6.8 mi (11 km) northeast, and the San Andreas Fault about 11.8 mi (19 km) southwest."

Jan 1, 2014

By Deepak Pappusetty, Miguel A. Pando

This study is motivated from the increased interest in recent years to explore use of Ocean Energy Converters (OEC’s).OEC’s can be tidal or generate electricity from wave or current action. Design of foundation systems for these OEC’s is a key consideration as it can represent about 35% of the initial installation cost. The primary focus of this paper is related to foundation systems involving monopiles where a key design consideration includes gradual accumulation of pile head deformations beyond serviceability limits of the OEC. This design consideration is important since these foundation systems are often subjected to more than 108 low amplitude repetitive dynamic load cycles during a normal 30 year design life. Research on single model piles installed in sand and subjected to over 104 low amplitude lateral load cycles have shown that pile head displacements and rotations tend to increase gradually with increasing load cycles. This gradual development of pile head deformation is related to plastic strain accumulation in the soil in the vicinity of the monopile. Analytical methodologies based on conventional p-y curves typically cannot predict these accumulated pile head rotations and displacements. Even 3D dynamic Finite Element Analyses may not capture this response for several conventionally used soil constitutive models. This manuscript presents predictions using p-y based methods as well as 3D dynamic finite element analyses. The different numerical predictions are compared to available experimental data. Results from this study show that conventional p-y methods do not predict the gradual pile head displacements observed experimentally. Modified p-y curves, developed for cyclic loading, do a better job than conventional p-y curves but tend to greatly under predict deformation. This is believed to be related to the cyclic load test data used to develop these cyclic p-y curves which involved at most up to 500 cycles and did not include high frequency contents or partial unloading cycles. The 3D FEA captured reasonably well the general observed trends of gradual accumulation of pile head rotation and lateral deformation with increasing constant amplitude lateral load cycles.

Jan 1, 2015

By Paul M. C. B. M. Cools, Martin Th. van Staveren

In 2010, the 5-years joint industry programme Geo-Impuls started in the Netherlands. The ambitious goal of this programme is to reduce geotechnical failures in our civil engineering projects by half in 2015. In the Geo-Impuls programme over 40 client organizations, engineering firms, contractors, research institutes, and universities are involved. In a risk-driven way, and based on top risks and dilemmas, the participants defined three central development themes. These themes are (1) contracts, for dealing with legal issues, (2) geo-engineering, for dealing with technical issues, and (3) communication, for paying attention to differences in risk perception by the human factor. In total 12 Working Groups contribute to these themes by producing one or more specific tools. These provide practical solutions for how to deal with contractual, geotechnical, and communication issues. The tools include working processes, guidelines, best practices, as well as some instruments. The development of these tools, as well as the available results, will be presented in this paper. From the start, Geo-Impuls embraced geotechnical risk management (GeoRM) as the risk-driven way of working for geotechnical engineering and construction. Over the past years, GeoRM and its supporting tools were already successfully applied in several projects. Therefore, the paper also describes also the GeoRM implementation process, including the quality assurance and control. Finally, the effectiveness of GeoRM will be discussed, by summarizing an analysis of all published geotechnical failures and accidents in construction projects in the Netherlands, which decreased substantially over the past 4 years.

Jan 1, 2017

By Abid Adekunte

"In recent years, developers have had to deal with complexities associated with numerous cases of deep basement construction in built-up areas. Design and construction of deep excavation support systems in urbanised zones come with many technical challenges. Restricted working spaces often render the use of temporary struts as wall restraint systems unpopular, as working space needs to be maximised. Also, tie-back anchors are often inapplicable due to the existence of adjacent structures. Therefore, developing alternative restraint systems for deep basement structures in builtup areas is becoming increasingly important to the present day basement engineer.This paper is centred on the design, construction and monitoring of enabling works for deep basement structures on three sites in the United Kingdom and Republic of Ireland. Traditional tieback anchorage and propping systems were inapplicable on the sites. As alternatives, separate novel wall restraint systems were developed and adopted, to enable excavation on each of the three sites.Performances of the novel wall restraint systems, as well as the responses of adjacent structures were monitored. Numerical modelling and field monitoring results show the three alternative wall restraint systems to be safe and effective. The paper also highlights the advantages of the novel solutions over conventional methods.INTRODUCTIONRecently, deep basement structures have become popular components of urban building developments. As pointed out by Pearlman et al., 2004, this could be attributed to the inadequacy of surface parking spaces in urbanised zones, while underground parking facilities are also believed to improve both aesthetic and commercial qualities of urban structures.However, while the incorporation of basement structure into new urban development appeals to developers and architects, the engineering design and construction aspects of basement works typically come against a whole lot of complexities and challenges. As highlighted by Wong, 2002, engineering problems associated with basement construction in built-up areas are numerous, some of these include; complicated sub-soil conditions, dealing with excessive active pressures, complex temporary works, proximity of sensitive adjacent structures, high level hazards to construction workmen and surrounding community, inadequate working space, etc."

Jan 1, 2015

By Pierre Gouvin

This paper describes the design, installation and monitoring of a state of the art real time geotechnical/structural instrumentation monitoring system to facilitate tunnel construction under Interstate route I-5 in Seattle, Washington, USA. The project involved removal of existing highway foundation substructures on both North and Southbound lanes as well as the underground reversible high occupancy vehicle lanes. The system utilized state of the art 3-D pulsed laser scanning, wireless sensor networks, automated robotic total stations, tilt beam sensors, narrow angle tiltmeters, and in-place inclinometers. Dedicated real time data loggers, with a web based graphical interface, provided 24/7 access to critical measurements. In addition to the instrumented sections of wall and roadway subsurface which monitored physical measurements at known points, the pulsed laser scanning allowed complete site monitoring coverage where physical sensors were not located. This data allowed post processing at any location enabling the contractor and designer to respond to unforeseen structural responses to construction. Use of the instrumentation system resulted in the early detection of wall movement, and provided feedback to the designers to facilitate construction process changes in order to minimize further movement.

Jan 1, 2010

By F. M. Abdrabbo

Flight auger bored piles are formed by screwing a continuous flight auger into the ground, and pumping cement/sand grout or concrete down the hollow stem of the auger as its withdrawn. The auger is driven at the top by hydraulic or electrical motor and is guided by a vertical crane leader. Loading tests on concrete piles are described. The stability plot method is used to drive the shaft friction and the end bearing load components of the pile capacity. This paper outlines features of crucial construction factors that affect the geotechnical capacity of this type of piles. These factors include, vertical speed of auger during boring, grout factor, grout pressure, number of reborings, type of material, and slump of concrete used to form the piles. Two of these factors are highlighted in this paper. It was found that, shaft resistance is independent of grout factor, whilst point resistance increases as grout factor increases. Nevertheless the engineer should decide the safe pile load associated with the most economical grout factor. High vertical speed of auger during boring of piles may cause disaster for the adjacent buildings, due to soil decompression.

Jan 1, 1993

By William H. Walton, Joel Dellaria, Jeffrey R. Hill

The City of Chicago has a world-renowned skyline and is known for its provocative architecture. The subsurface conditions in the city have allowed for construction of these significant structures. The skyline is supported on caissons as they are called in Chicago or drilled shafts in other locations. Despite the significant strides the industry has made in advancing the drilled shaft, the use of other specialty geotechnical construction techniques like micropiles has not been overlooked in Chicago and the surrounding areas. Micropiles have been utilized to underpin famous existing historic structures like Orchestra Hall any many others. Engineers have used 200 to 600 kip micropiles to underpin compromised, inadequate, or damaged caissons. The paper will discuss the use of drilled shafts, micropiles, and ground improvement over the last 30 years in Chicago using a curated collection of case histories. It will also examine advancing the industry beyond its current technical limitations using these techniques. INTRODUCTION 20,000 years ago, glaciers from the Chicago region left behind sheets of glacial clay till underlain by dense, over consolidated glacial till below: limestone bedrock, found about 100 ft below street level. An unusual feature in this profile is the soft Chicago Blue Clay. Chicago has been called the birthplace of the Skyscraper and drilled shaft foundation, both of which came about in the 19th century. After the Great Fire of 1871, tall new structures were built rapidly and designing a successful foundation was trial and error. The first deep driven wood pile and caisson foundations bypassed the problem layer and found solid support on hardpan till or bedrock below (Schock and Risberg 2013). Once the drilled shaft foundation became acceptable to the Chicago engineering and construction community, building heights and complexity grew dramatically. As the city grew, building foundations were being repurposed. There was also the need to underpin structures for additional loads and shallow foundations for adjacent construction. Hand-dug drilled shafts were an option for some of these restricted access and low headroom sites but a new technique, micropiles, would prove to be the future of retrofit and hard to construct foundations. Micropiles were introduced on a limited basis to the United States market in the 1970s and 80s. In the early 1990s, the Chicago market began to latch onto micropiles and their use has grown significantly as a solution to the most complex foundation problems a maturing skyline has to offer.

Jan 1, 2019

By Dennis Nottingham

Increased interest in seismic soil liquefaction and preventative soil stabilization sets the stage for improved deep compaction methods using pile driving techniques. In 1971 L.B. Foster Company personnel patented a method of deep compaction using a vibratory pile hammer and pile probe. The technique had some success, but did not produce consistent results and thus found its way to obscurity. Other patents attempted to modify the technique by various probe modifications, but again without measurable improvement from a practical point of view. Solutions to economical deep compaction up to 100-foot depths particularly in saturated granular soils would have a great impact on the construction industry and new bulkhead structures being developed, thus PND was prompted into related research and development. The advent of higher horsepower vibratory hammers, coupled with PND engineers' experiments, observations and measurements, led to an "H" pile probe design which has produced measured soil density improvements up to 250% using SPT "N60" values as a measure. Case histories of two projects involving extensive SPT soil sampling comparative measurements will be discussed along with findings that led to the compaction success. Applications to numerous modern "Open Cell" bulkhead projects will be presented and discussed.

Jan 1, 2004

By Viswanadham B. V. S., Babu K. V

Many refineries are in the process of revamping and expanding their existing facilities. Most of the refineries are located in coastal areas due to ease of transportation and storage of crude oil. Considering the criticality of structures as well as prevailing soil conditions, most of the structures are supported on pile foundations. In depth review of sub-surface investigations data followed by liquefaction assessment of the site, it is noticed that site is prone to liquefaction during the seismic event. Among various techniques, driven cast-in-situ piles were selected to mitigate liquefaction. Static cone penetration tests were conducted during the pre and post installation of driven cast-in-situ piles at identified locations. Analysis of cone penetration test data shows that considerable ground improvement has been achieved post-installation of driven cast-in-situ piles.

Sep 1, 2022

By Monica R. Garcia, Antonio Alberto S. Correia, Paulo J. Venda Oliveira

"The aim of this paper is to analyze the creep behavior of a Portuguese soft soil stabilized with binders in one-dimensional conditions, based on oedometer creep tests. The study focuses on the analysis of the effect of the binder content and binder type on the creep behavior of a stabilized soil. The results show that the best binder type for this soil, in terms of creep behavior, is composed of Portland cement and fly ash with a dry weight proportion of 75/25, as this promotes the development of secondary pozzolanic reactions. The results also show the decrease in the secondary compression index with the increment of the binder content, since it promotes an increase in the cementation bonds between soil particles. The general analysis of the results shows a clear dependence on C??and qu, until values of qu of 1500 kPa; after that this relationship is negligible.INTRODUCTIONThe geotechnical structures (such as embankments, dams and buildings) built on organic soils exhibit notable creep deformations, which increase the maintenance and exploitation costs and can even compromise their functioning. To attenuate the creep effects of the soft ground, some improvement techniques are frequently used, such as preloading or reinforcing the soil foundations with vertical rigid inclusions, like concrete piles, stone columns or deep mixing columns (DMCs). However, the installation of DMCs in the soft ground induces (via the arching effect) a transfer of stresses from the soft soil to the DMCs, which causes an increase in the creep settlement on the DMCs (Venda Oliveira et al. 2011).Notwithstanding the fact that the creep behavior of clays has been the object of several studies (Leroueil et al. 1985; Mesri and Castro 1987; among others), the study of the creep behavior of soil-binder admixtures has been practically ignored by the scientific community. The few studies on this theme have revealed that a stabilized soil’s creep behavior is dependent on: the type of binder (Venda Oliveira et al. 2013), the binder content (Correia 2011; Bobet et al. 2011; and Venda Oliveira et al. 2013), the stress level applied during the creep phase (Venda Oliveira et al. 2013), the organic matter content of the natural soil (Venda Oliveira et al. 2012; 2014), and the curing conditions (humidity, vertical stress applied during curing, and curing time) (Correia 2011; Venda Oliveira et al. 2012).The aim of this paper is to contribute to a better understanding of the creep behavior of a soil-binder admixture, by examining the results of oedometer creep tests. The study focuses on the analysis of the effect of the binder content and binder type on the creep behavior of a stabilized soil. Additionally, the creep behavior is correlated with the effective vertical yield stress and the unconfined compressive strength (UCS)."

Jan 1, 2015

By David Miller

"The biggest concern about using soil mixing is the inability to observe physically the final product, which has led to a lack of confidence about what is in the ground. After all, you can’t see it and you can’t taste it and you can’t smell it, so are you sure it’s soil mixing? In addition, there are variations in techniques, tools and monitoring that have led to additional skepticism and the desire to “elevate” the product. This skepticism is why the industry is so scrutinized even when there are other technologies being used that do not experience nearly the same level of scrutiny. With other techniques, even with a slurry wall, you can see the backfill before it goes into the ground, and drilled piers have careful evaluation of the concrete mix even before placement into and verification of the open hole. Essentially, you get control over the final material. There is less control in soil mixing, and it’s very dependent on in-situ conditions. These factors make it difficult to rely solely upon installation parameters, quality control (QC) and verification tests. At some point, you may need to apply some engineering judgment.Start at the BeginningThe availability of sufficient and accurate geotechnical data (soil type, heterogeneity, shear strength parameters, variability, etc.) is important in establishing the material that will be drilled. This data will also help in determining the proper mix design to achieve the desired soil cement properties. Many factors must be considered when designing the mix and the mixing program, including any debris in the ground, different soil properties and varying moisture contents.Each of the various factors affect the final properties of the soil cement, so it really takes careful planning and evaluation of the mix design through iterations by looking at the soil types and adjusting the mixes. Clay is going to behave very differently than sand in both mixing efficiency and final properties. That is, the presence of clays results in more difficulty in achieving higher strengths and to physically mix the soil and the binder, whereas the presence of sands results in more difficulty controlling the final permeability."

Jan 1, 2017