Search Documents

By Robert H. Richards

(Pittsburg Meeting, March, 1910.) THIS is in part a review paper, indicating the various steps that have been taken in developing hindered-settling apparatus, some of the standard data that have been obtained, and some of the conclusions one is led to as to the effect of it in improving concentrating-methods and machinery, and in part it brings in some unpublished work. CAUSES OF LOSS IN ORE-CONCENTRATION. In making a study of the separation of valuable minerals from the waste gangue, particularly by water concentrators, it is necessary to define, first of all, what are the causes of-loss that are likely to interfere with the concentration. Having made this definition; we can then study to see in what way the machines make their losses, and plan remedies for them in an intelligent way. Losses may be stated to occur as included grains, as flat or long grains, as fine free mineral, and as absolute slime. We will take, these up one by one, as follows: Included Grains.-Fig. 1 shows by a set of diagrams how included grains may occur: first, where the heavy mineral grains attached to the quartz are of large size; secondly, where they are of small size ; and thirdly, where very fine particles of heavy mineral are included in the quartz. We have to decide in regard to included grains whether they are rich enough to go direct to, the furnace, or poor enough to throw away, or whether they lie between these two points and require recrushing as the only means of severing the values from the waste. This last case is the only one requiring special treatment at our hands. We will therefore consider that next. * By mutual consent, this paper has been presented also before the Colorado Scientific Society, and the Canadian Mining Institute, Montreal.

Feb 1, 1911

By W. D. Sylwestrowicz

In tests on polycrystalline copper and aluminum, the ratio of the yield stress to modulus of elasticity was found to be strongly dependent on tempemture. Also, it was shown that the change of the yield stress with temperature of a material at a given temperature and deformed to a given yield stress, but not necessarily to the same strain, does not depend on previous mechanical thermal history. Likewise, for a material at a given temperature and deformed to a given yield stress, the rate of work hardening is independent of the temperature of prior stressing. It has been shown by Los and Orowan1 and by Dorn, Goldberg, and Tietz2 that the temperature dependence of the yield stress-strain curves of crystalline materials reflects two effects: not only does the yield stress of a material in a given structural state depend on the temperature, but the structural state (and the corresponding strain hardening) after a given amount of plastic straining also depends on the temperature at which the pre-straining has been carried out. Thus, for instance, if a specimen of a ductile metal has been strained along the stress-strain curve 1 at room temperature to point A, Fig. 1, and then the straining continued in liquid nitrogen along curve NR, the yield stress A' immediately after lowering the temperature is lower than the yield stress A" of a specimen that has been strained by the same amount in liquid nitrogen (along curve 3). AA' represents the effect of the temperature change upon the yield stress of the specimen pre-strained at room temperature; A' A" is the excess strain hardening acquired if the pre-straining has been carried out in liquid nitrogen instead of at room temperature. The dependence of the yield stress (i.e., of the structural state acquired during preceding straining) upon the conditions (speed, temperature) of a pre-straining is the reason for the nonexistence of a so-called "mechanical equation of state" for plastic deformation. A 'mechanical equation of state" is a relationship of the form F(s,E, e, T) = 0, or s = f(E, E, T) [1] It was first suggested by Ludwik3 that plastic deformation might obey such an equation; this, however, was conclusively disproved by experiments of Kochendorfer.4 Additional disproofs were given in

Jan 1, 1959

By Walter V. Knopp, Laurence Delisle

The aim of this work was the preparation of nickel-steels from elemental metal powders by powder metallurgy techniques. It was known that plain carbon steels could be made from a mixtufe of iron powder and graphite and that the effect of carbon on iron in powder form was of the same nature as that produced in fusion metallurgy. The problem in making nickel steels from elemental powders consisted therefore in finding out whether sufficient diffusion of the nickel and other incidental metals . normally present in such steels could be induced in the solid state to modify the properties of plain carbon steels made from powders and produce the beneficial effect of alloying. The composition selected originally was that of an S.A.E. 2330 steel. Metal powders, in the proportion correspending to that composition, were mixed with graphite, pressed, and heated at different temperatures for different periods of time, to produce bonding of the metal particles and mutual diffusion of the various elements without melting. Temperatures up to 1325°C and sintering periods as long as 6 hr were first investigated because it was expected.that such conditions would produce maximum diffusion with an accompanying improvement in the properties of the alloy. It was found that, although diffusion proceeded to a large extent under the conditions investigated, it would not be complete unless sintering were carried out at a high temperature for much longer than 6 hr. Relatively high temperatures and long sintering times are objectionable from a practical point of view, particularly when a low COSt material is to be produced, because they necessitate the use of special, costly equipment. Work could be done to improve the diffusion of iron and nickel by changing conditions other than the sintering temperature and time, that is, finer primary or alloy powders could be used. However, a marked change in the properties of the steel had been observed even with only partial diffusion. It was thought, therefore, that instead of trying to improve the diffusion, advantage might be taken of its incompleteness to produce a special structure consisting, in the unquenched condition, of a hard constituent, rich in nickel, dispersed in a tough pearlitic matrix. Steels with such a structure, not readily obtainable by fusion, should have desirable mechanical properties. Besides, it should be possible to prepare them from elemelltal powders under economical conditions. This latter alternative was therefore adopted for the second phase of this work. This report is divided into four parts: I. General Procedure. 2. Effect of Sintering Temperature. 3. Effect of Varying the Nickel Content. 4. Effect of Alloying Elements. General Procedure The general technique of cold pressing as used in powder metallurgy was applied.

Jan 1, 1949

By IRVING H. WENTIVORTII

(New York Meeting, February, 1912.) THE little town of San Nicolás, Tamaulipas, Mexico, lies approximately 60 miles east of Linares, situated in the State of Nuevo Leon, and 150 miles SE. of Monterey, as shown in the sketch-map. Fig. 1. The place is reached from Monterey by the Tampico train as far as Linares, a distance of 92 miles, and then by coach the rest of the way. It is situated in a narrow valley between low hills, the houses forming one main street and a plaza. It is peopled by about 500 inhabitants. The climate is temperate, the thermometer ranging from 90° in summer to a few degrees below freezing-point in winter; but this severe weather only lasts a day or two at a time, when the " northers " blow. There are no streams in the vicinity, but water sufficient for the use of the people is obtained from wells. The rainfall is about the same as that in the rest of NE. Mexico. The rainy months are July, August, and September. The rest of the year is practically dry, with an occasional showery day or two during the winter, when a " norther " is blowing. Timber is abundant in many localities. There are two varieties of oak, besides mesquite, ebony, "maguira," "patol," and a number of other kinds of trees indigenous to this region. I. HISTORY. On the discovery of the silver-lead hearing veins occurring in this district, the mining-camp of San Nicolás was founded in 1767 by the Spaniards, and numerous mines were opened and worked for a distance of abort 3 miles east and 5 miles west of the town. At the western extremity and near the Carrolena mine, a small town called San Pedro was built. The ruined walls of the houses form a single street, and all is over-

Aug 1, 1912

By Robert M. Grogan, Gill Montgomery

Fluorspar, the commercial name for fluorite, is a mineral composed of calcium fluoride, CaF,. Its valuable properties are due to its content of fluorine, and it is the principal commercial source of that element. The name is derived from the Latin word "fluere," to flow, because the mineral has a low melting point and is used in metallurgy as a flux. Cryolite is a sodium aluminum fluoride, Na,AlF,. It is a rare mineral which has been found in commercial quantities in only one place in the world, Greenland. Small amounts of it are shipped from stock in that country, and its place in industry has been taken over almost completely by synthetic cryolite. Because of the relative unimportance of cryolite, discussion of it has been relegated to a short section at the end of this chapter, which is principally concerned with fluorspar. History Fluorspar was used for ornamental purposes by the Greeks and Romans, who fashioned such things as vases, drinking cups, and table tops from it. Various peoples including the Chinese and the American Indians carved ornaments and figurines from large crystals. Its usefulness as a flux was known to Agricola (1564), who wrote about it in 1546. Mining began in England about 1775 and at various places in the United States during the period 1820 to 1840. Production became substantial following the development and widespread adoption of the basic open hearth method of making steel, in which fluorspar is used as a flux. After that, production and usage were stimulated by growth in the steel, aluminum, chemical, and ceramic industries and were accelerated by World Wars I and II. Fluorocarbons entered the picture in 193 1 and the use of anhydrous hydrogen fluoride (HF) as a catalyst in the manufacture of alkylate for high octane fuel blends began in 1942. The development of the froth flotation process in the late 1920s, a differential flotation scheme for separating fluorspar from galena, sphalerite, and common gangue minerals in the 1930s, and the application of heavy-media concentrating methods to the treatment of low grade ores in the 1940s were outstanding technological contributions that enabled increased production of fluorspar concentrates. In recent years the development of pelletizing and briquetting processes for making flotation concentrates into gravel-size particles for use in steel furnaces and the development of more efficient and selective flotation schemes for treating crude ores containing abundant dolomite and barite have been major improvements in the industry.

Jan 1, 1975

By J. W. Mills

This paper's aim is to demonstrate, by reviewing findings and conclusions of earlier authors and through recording and interpreting the outcome of recent laboratory study of the ores, that the ores around the Gem stocks are metamorphosed equivalents of common siderite-sulfide ores far from the stocks, as was first proposed by Hershey (1912, 1913). That is, all the ores probably have the Precambrian age of 1250 million years reported by Long et al. (1960). Those near the Gem stocks, however, were extensively metamorphosed in Cretaceous time during the emplacement of stocks so their resemblance and relation to other veins in the district are camouflaged.

Jan 1, 1985

By Arthur Taggart

THE major portion of the work described in this paper was performed by R. W. Young,+ a graduate student in the department of Mining and Metallurgy, Sheffield Scientific School, Yale University, working under a cooperative agreement between the Hardinge Conical Mill Co., the Sheffield Scientific School, and himself. Since this cooperative scheme is at present in effect in the case of a considerable number of other students in the department and since it is the hope of the school that the privilege thus extended may be utilized even more freely in the future by mining and manufacturing companies, it may not be amiss at this point to give a summary of the general plan. Briefly it is as follows: A graduate student, whose undergraduate work in this or other universities shows promise of ability to handle research work, is chosen by conference between the company and instructor involved. The aim of the company in the agreement then entered into is to obtain the solution of one or more of the technical problems with which it may be confronted, or, at the end of 1 or 2 years, to obtain as an employee a man especially trained in its work. As. a means to accomplish one or both of these ends, the company furnishes the machine, apparatus, or material to be tested and pays the student during his graduate work a small salary, usually just sufficient to cover his living expenses, tuition and fees. The aim of the student is special training along a line in which he is particularly interested, the attainment of his advanced degree, and the chance to show to his future employer ability to handle such problems as may be presented to him. In return for the financial aid which he receives he agrees to devote at least half of his working time to the special problem submitted by his company. The other half is devoted to study of the collateral subjects required by the department for the granting of the degree which the student seeks. The student further agrees to enter the employ of the company in question at a wage not greater than that paid in like positions to recent graduates not specially trained and to remain with his employer at such wage for at least 1 year. If the student is to obtain a degree, the special work forming the basis of his investigation must be such as will involve real research and not mere routine manipulation. The subject is chosen by conference between the three parties to the agreement. The work is carried on under the direct supervision of the instructor involved. The school furnishes the general laboratory and library equipment essential to the pursuit of any extended investigation, In

Jan 4, 1917

By G. Caetani

I. INTRODUCTION. WE owe to the courtesy of Mr. R. M. Raymond, Manager of the El Oro Mining & Railway Co., Ltd., the permission of publishing in this paper the results of a series of experiments and tests made in view of determining the economical limit to which the fine grinding of the ore by tube-mills could be carried on. For the sake of clearness, the following definitions are given of certain terms used in this paper, as well as of the units and screens in the experiments. Slime : In a general way " slime" is that mill-product, of which from 90 to 95 per cent, will pass a 200-mesh screen (0.067 mm. aperture), and which is treated as one class of material in the El Oro cyanide-plants. As a screen-product, slime constitutes all material that *ill pass a 200-mesh, screen. In sizing, the following products are distinguished:- Coarse Sand : That material remaining on a 100-mesh (0.111 mm. aperture) screen. Fine Sand : That passing through. 100-mesh and remaining on a 200-mesh (0.067 mm. aperture) screen. Slime: That passing through 200-mesh. Fines, which pass through 200-mesh and settle in 30 seconds, and silt, which does not settle in 1 minute. Sand-index : The number proportional to its total fineness considered from the economical point of view, as explained on page 93. Absolute extraction : The percentage of values actually brought into solution. Actual extraction: The percentage of values actually brought to the ziuc-boxes. Units : Dollars, U. S. Currency; pounds; and short tons (2,000 lb.). Gold is valued at $20.67, and silver at $0.50 per ounce. Screens : In the sizing-tests the screens used were:¬ Mesh (per 1 in.), . 24 30 40 60 80 100 150 200 250 Aperture (mm.), . 0.740 0.515 0.424 0.250 0.159 0.111 0.090 0.067 0.058 Strengths of solution : Strengths are expressed in the percent- . age of KCN contained, though the sodium cyanide, which is

Jan 1, 1906

By K. A. Natarajan, I. Iwasaki

With a platinum electrode the Eh-pH response in aqueous systems follows an empirical relation [Eh = E- 0.059 pH](1) where E usually carries a value between 0.8 and 0.9 v. The same potential (E) is observed with a number of other noble metal electrodes in the absence of surface poisoning and of other well-defined redox couples. Many sulfide mineral electrodes also respond in a similar manner in solutions containing their respective ions over wide pH ranges, especially in the alkaline pH region. Such a parallelism between noble metal and sulfide mineral electrodes points to certain implications of their surface conditions, and the flotation and leaching behaviors of sulfide minerals under aerated conditions may be inferred with respect to the foregoing Eh-pH response. Comparison of Sulfide Mineral and Noble Metal Electrodes [Fig. 1] shows the Eh-pH response of pyrite, galena, chalcocite, and pyrrhotite electrodes, reported by Sato, and some experimental points obtained with a platinum electrode in distilled water. [Eq. 1] is seen to be followed by all these electrodes. It is interesting to note that the response of the pyrite electrode as shown is identical to

Jan 1, 1973

By Leo J. Vogel, E. D. Hummer, David J. Akers

INTRODUCTION An efficient refuse-disposal system is a necessary part of the modem cleaning plant. The large-scale refuse system and disposal area, engineered for the lifetime of the plant, has become more important due to the greater tonnages of refuse produced from increased quantities of mechanically mined and prepared coal. Laws and increased government regulations have affected the design and operation of disposal systems. THE EFFECT OF MINE AND PLANT OPERATION Refuse disposal starts at the mining face. The mining system, the type of roof support, the machinery used, and the degree of discipline at the face contribute to the amount and type of refuse that must be removed through the disposal system. Economies gained through modification of the mining system or mining machinery may be partially offset by increased dilution of the mined coal with impurities from associated rock formations. In some cases the change in the mining system and equipment has reduced the dilution. In all cases the ratio of impurities that must be removed from the raw-coal feed to the plant not only affects the maintenance and

Jan 1, 1979

By Ganesh P. Mohanty, James J. Wert

THE brittleness of the intermetallics usually render their deformation studies at ordinary temperatures using conventional techniques inadequate. On the other hand, although X-ray line broadening measurements is not a complementary technique, it provides a means for gaining limited but useful information on the cold worked state of these materials. In the present instance, a study of the effects of cold work in the lead telluride intermetallic compound was carried out by analyzing the diffraction profiles of the deformed and the corresponding annealed samples. An ingot of PbTe was prepared by induction melting high-purity lead and tellurium in a quartz crucible under an atmosphere of argon. After homo-genization, the ingot was ground to -325 mesh at room temperature, and using a polished die the cold- worked powder was pressed into the form of flat faced briquets for diffraction measurements. A spectrometer with 0.125 deg per min scanning velocity, CuKa radiation, pulse height analyzer, and a proportional counter were employed in the X-ray measurements, and the powder peaks were collected from the sample in fully cold-worked state and after it had been annealed to relieve the effects of cold work completely. For reliable estimates of the peak extremities, small angular ranges where the tails merged into the background were point counted. Fourier inversions of the experimental peaks were carried out in an IBM 705 computer using the procedures introduced by stokes.' Both the cosine and sine components of the Fourier series were used to take into account any peak assymetry arising

Jan 1, 1963

By J. T. Eash, N. B. Pilling

As a group, the alloys of iron, nickel and carbon are, in application, one of the most versatile of the ferrous alloy family, and while many investigations have been made of their properties and structure only a few attempts have been made to show the microstructural relation over a wide range of composition. It is necessary at once to be clear about the kind of structural relation with which we are concerned. The equilibrium diagram provides quantitative data regarding structural make-up and its variation with temperature, but equilibrium structures often are far different from the technologically significant ones. This is particularly true of steels and cast irons, and some of the most important components of their structure may have no place in the diagram of equilibrium. The fugitive phases that result from transformation are dealt with in a highly detailed and descriptive manner in the S-curves originated by Bain. The present effort lies in a still different field, which is to portray the relation between sweeping changes in composition and in resultant structure, under controlled but nonequilibrium conditions of thermal treatment. The Guillet1 diagram presented in 1903 was the initial attempt at such a correlation and frequent references to this diagram can be found in the literature even though later work has shown it to require considerable modification. Kase2 published in 1925 a diagram that was based upon observations of furnace-cooled melts. At low carbon contents this diagram agreed fairly well with experience in showing pearlite to exist in alloys containing up to 6 per cent nickel, and completely austenitic steels at 24 to 28 per cent nickel. At high carbon contents, however, irons were indicated as being martensitic at around 2 per cent nickel and austenitic at 12 per cent nickel; these interpretations are open to serious question. Based upon experience with steels and cast iron, Wickenden3 suggested a diagram that agreed fairly well with Kase's in the steel range but which presented a wide departure from it in the higher-carbon, high-nickel regions. In its broad picture, the Wickenden diagram is an approach to "practical" structures. [ ] Reference may be made at this point to the efforts of Marshy to construct an iron-nickel-carbon equilibrium diagram by the coordination of scattered data, which are described at length in the monograph cited. None of these preceding attempts has appeared to meet the need for an exposition of the structural sequence that is encoun-

Jan 1, 1942

By H. H. Campbell

Many attempts have been made to write a formula by which to calculate the strength of steel from its chemical composition, but most of these endeavors have failed because there were too many disturbing conditions. It is idle to collect from the pages of trade-papers, books, or the proceedings of scientific societies, a multitude of observations. The combination of such results will simply show that steel of the same composition will vary in tensile strength through wide limits—a fact that has been known for generations. That cold-working, overheating, and many another form of heat-treatment alter fundamentally the strength of steel, is ancient history, although it is only recently that the microscope has pointed out the road to an explanation of the phenomena. It mag be urged that the microscopic structure must betaken into consideration in any formula giving the ultimate strength, but from the standpoint of the present investigation this is unnecessary. We are trying to determine primarily, not what changes in ultimate strength may be made by variations in the condition of carbon, but what effect is produced by changes in the amount of carbon, when its condition remains constant. For such an inquiry, in order that the condition of the carbon should remain as nearly uniform as possible, it is essential that all testrpieces be made under the same conditions; and it is believed that the tests described in this paper satisfy that requirement. The investigations were made at the works of the Pennsylvania Steel Company, Steelton, Pa.; the ingots from which the tests were made were 6 in. square in every case; they were heated in the same furnace and forged at the same ham-

Jan 1, 1905

By W. L. Fink, H. C. Stumpf, L. A. Willey

VERY few studies of the aluminum-sodium system have been reported. Heycock and Neville1 were unable to detect any solubility of sodium in liquid aluminum. Mathewson2 prepared an equilibrium diagram consisting of two horizontal lines at the melting points of the two metals. He was unable to detect solubility at either end of the system. Scheuer3 first developed a method for the chemical determination of sodium in aluminum and then studied the solubility of sodium in liquid aluminum. His method involved heating aluminum with excess sodium under hydrogen until the two liquids were at equilibrium, chilling the melt, and analyzing the aluminum-rich layer. He reported the solubility to be 0.l0 pct sodium at 700°C, 0.115 pct at 750°C, and 0.128 pct at 800°C. This paper on the aluminum-sodium system is the twenty-first in a series from the Aluminum Research Laboratories describing equilibrium relations in aluminum alloy systems. MATERIALS The alloys for this investigation were prepared from electrolytically refined aluminum (99.99 pct) and sodium of reagent quality conforming to specifications of the American Chemical Society.4 Chemical analysis of the aluminum showed the following impurities: 0.002 pct Si, 0.002 pct Fe, 0.002 pct Cu, <0.001 pct Mn, 0.002 pct Mg and 0.001 pct Na. The sodium content of all alloys was determined by either chemical or spectrographic standard procedures5 No. IIA and No. SII respectively. DETERMINATION OF LIQUIDUS The boundary of the miscibility gap was determined by a modification of the method of Scheuer3 and of that used by Henry and Cordiano.6 As finally developed the method was as follows: A fused alumina crucible 25 mm id with 75 mm depth and 1.5 mm wall thickness was placed on the bottom of a container made from a 4-in. length of 1 ½ -in. iron pipe and pipe caps. The space around the sides of the crucible was filled with 40 mesh crystalline alundum. A charge of 60 g of aluminum and 10 to 15 g of sodium was placed in the crucible, the sodium first being trimmed and rinsed with iso-pentane to remove kerosene. The container was tightly capped, filled with argon (99.6 pct pure), and heated to the desired temperature (between 670 and 800°C). A positive pressure of argon (about 8 mm of mercury) was maintained through a small pipe to the upper cap. After soaking for from 2 to 5 hr, the container was quenched by directing a stream of water onto the base, so that solidification of the aluminum-rich layer was rapid and essentially unidirectional. Analyses were made on drillings taken from the bottom of the ingots after machining off the surface layers. Pre-

Jan 1, 1948

By L. Seigle, R. Resnick

An inert-marker movement experiment indicates that the ratio of the intrinsic diffusion coefficients DC:DTa = 80:l in TaC at 2500°C. Measurements of the diffmion coefficient of carbon in nonstoichiometric TaC at temperatures from 1700° to 2700°C reveal that Dc increases with decreasing carbon content, but much less than expected from the probable change in vacancy concentration with carbon content. A diffusion process involving two simultaneously operating mechanisms is postulated, and shown to be theoretically feasible. The average value of the carbon diffusion coefficient is given by DC = 0.18 exp[(-85,000 ± 3000)/RT] sq cm per sec over the composition range 46 to 49.5 at. pct C. BECAUSE of their high melting points and hardness, the carbides of the IV, V, and VI group transition metals, along with those of uranium, have attracted considerable interest for applications at high temperatures. In these applications the reactivity of the materials is important, and, since rates of diffusion within the compounds influence reactivity, a knowledge of diffusion kinetics and mechanisms is desirable. While many investigations of the mechanical and electrical properties of these compounds have been made, only two fundamental investigations of diffusion in the carbides are known. Chubb, Getz, and Townleyl measured the diffusivity of carbon and uranium in UC, and Gel&apos;d and Liubimov2 measured the diffusivity of carbon and niobium in NbC. This paper describes an investigation of the diffusion of carbon in tantalum monocarbide and, in particular, the influence of carbon deficiency on this process. Tantalum carbide melts at approximately 3800°C, which makes it one of the highest melting materials known. The compound exists over a rather wide range of carbon Content.3-7 At the peritectic temperature, 3240°C, the phase extends from about 36 to 50 at. pct C. Although the compound can exist with a substantial carbon deficiency, the high carbon phase boundary remains near the stoichiometric composition over the entire temperature range; i.e., no carbon excess is observed. The structure of TaC is the NaCl type wherein carbon atoms normally occupy the octahedral sites in a somewhat expanded fcc lattice of tantalum. Decrease of the lattice parameter with decreasing carbon suggests that the removal of carbon introduces octahedral vacancies into the lattice. I) EXPERIMENTAL DETAILS AND RESULTS Inert-Marker Experiments. In a compound such as TaC the interstitial element would be expected to diffuse more rapidly than the metal. This was confirmed by an inert-marker experiment, following Srnigelskas and irkeendall.8 Ideally, the markers should be placed at the interface between a slab of low-carbon TaC and graphite, and their movement during subsequent inter-diffusion measured. Unfortunately, no solid could be found which is unreactive in contact with carbon at the high temperatures employed in these experiments. In order to circumvent this problem, a specimen was designed in which the markers consisted of several small canals running just below the surface of a tantalum slab. This specimen was prepared by machining grooves on the surface of the tantalum slab and then diffusion-bonding a thin plate of tantalum to the slab over the grooves. The surface of the plate was then ground down until the distance between the canals and surface was as small as possible (about 0.01 cm). Thus, the canals would lie entirely within the TaC phase after a short period of diffusion. The diffusion anneal consisted of immersing the metal sample in high-purity graphite powder and heating for approximately 10 hr at 2500°C under vacuum. At this temperature, the vapor pressure is sufficiently high and the transfer of carbon from graphite sufficiently rapid to allow the surface of the diffusion sample to attain the stoichiometric carbon concentration very quickly. Conclusions regarding the relative diffusion rates of carbon and tantalum in the compound layers (TaC and Ta2C) can be drawn from the location of the canals after the diffusion anneals. If the growth of the layers is governed mainly by the diffusion of carbon, as expected, the canals should remain close to the sample surface. If the diffusion of tantalum contributes appreciably to formation of the compound layers, the distance from the markers (canals) to the surface should increase. Fig. 1 shows, diagrammatically, the appearance of the specimens after diffusion, and Table I presents the depth below the surface at which the

Jan 1, 1967

By G. L. F. Powell, L. M. Hogan

Samples of silver and Ag-O alloy, 0.12 wl pet, have been undercooled to a maximum of 250°C by melting in a slag of commercial soda-lime glass. Grain refinement occurred in undercooled silver samples whet the degree of undercooling exceeded a critical value which varied from 153° to 175°C, depending on the melting conditions. In under cooled Ag-0 samples, the grain structure was fine and equiaxed at degrees of undercooling larger than 50oC. The grain refinement in both silver and Ag-0 alloy samples was the result of recrystallization during or immediately following freezing. When the oxygen content was increased, the degree of undercooling at which recrys-tallization occurred decreased. INVESTIGATIONS of the grain structure of strongly undercooled melts of nickel and cobalt1-4 have revealed a change in room-temperature grain size as a function of undercooling. At large degrees of undercooling the grain size was fine, but samples undercooled by smaller amounts exhibited a much coarser grain structure. The reported undercooling at which this grain size transition occurred in nickel varied between 140° and 175&apos;C undercooling. Walker1 attributed this grain size change to an enhanced nuclea-tion rate. Cavitation at a melt-solid interface was con sidered to generate a high-pressure wave. This, in turn, produced nucleation in the liquid as a result of an elevated freezing point increasing the undercooling in the melt. A similar grain size transition was observed in undercooled silver between 133° and 153°C undercooling.5 The grain size transition in undercooled silver was found to be dependent on oxygen con tent. More recently, the authors5 showed that a simila transition occurred in an undercooled Cu-O alloy, =0.08 pet, but not in oxygen-free copper undercooled more than 200°C. The transition was attributed to recrystallization of the solidified grains after freezing; the greater the degree of undercooling, the more complete the recrystallization. In view of this effect of oxygen content on grain size transition, additional undercooling experiments were carried out with silver. This paper reports the results of these studies on silver and Ag-O alloys undercooled more than 50°C EXPERIMENTAL 1) Materials. The silver was supplied by Matthey Garrett Pty., Ltd., as fine granulate, silver mini&apos; mum 99.9 pet, and contained the trace impurities shown in Table I. The silver originated from two different refineries resulting in the difference in impurity content shown in Table I. However, the variation in composition had no discernible effect on the undercooling behavior. Samples of the silver were melted in an open-ended, vertical, cylindrical resistance furnace, wound with Kantha] wire, the temperature of which was adjusted by means of a variable transformer, 2) Melting and Undercooling. Bulk samples of silver were undercooled by preoxidation and removal of oxidized impurities in a glass slag, as previously described,5 but special precautions were necessary to allow comparison between oxygen-free silver and a Ag-O alloy. Samples free of oxygen were prepared by first melting weights of granulate varying from 200 to 400 g in clean vitreous silica crucibles in air for approximately 15 min. A sample was frozen and a complete glass cover formed over the top surface by adding granulated glass rod. The sample was then melted and frozen several times until no oxygen bubbles appeared in the glass slag. Subsequent thermal analysis indicated that the oxygen content was negligible. The glass acted as an efficient barrier to absorption of oxygen from the air. Ag-O alloys were prepared by melting silver in silica crucibles with only a partial cover of glass, so that the top surface of the melt was in contact with air. The silver was held molten in air for several hours at 1000° to 1050°C, in the expectation that the oxygen in solution would reach equilibrium with atmospheric oxygen. At T - 1000°C the equilibrium oxygen content was calculated as 0.12 wt pet O, using Sieverts law and Eq, [l], derived by Mizikar et a!.7 from the data of Sieverts and Hagenacker8 for 1 atm of oxygen:

Jan 1, 1970

By B. E. Sundquist

The various methods based on solution models for obtaining free energies of mixing from miscibility-gap data have been applied to a number of binary-alloy systems. For nine of these systems there exist experimental thermodynamic data that permit a comparison of the results to experiment. It was found that the method of van der Toorn and Tiedema almost invariably leads to results that are physically unacceptable and that vary drastically with small changes in the miscibility-gap parameters. The subregular solution model is found in all cases, except the Al-Zn, Fe-Cr, and Cu-Pb systems, to exaggerate the free energy of mixing by 30 pct or more. The model developed by Lumsden is found to give results that are often in excellent agreement with experiment and which exaggerate the free energy of mixing by no more than 30 pct. These results and others give evidence that the Lumsden treatment of the effect of unequal atomic sizes and of imperfect configurational randomness due to deviations of AB bond energies from the mean of AA and BB bond energies is adequate for most systems. ANALYTIC expressions are frequently proposed for the dependence on composition of the activities of the components of a solution. Because the development of solution theory is incomplete, these expressions contain parameters which must be determined by experiment. The measurement of activities is often difficult and consequently such measurements are less readily available than are measurements of phase equilibria which, under certain conditions, can also be used to evaluate these parameters. For example, suppose it is known that two structurally dissimilar phases, each of known composition, in an n-com-ponent system are at equilibrium at a given temperature and pressure. n equations can be set up in terms of these parameters expressing the equality of the chemical potential of each component in the two phases. In addition, one can write the Gibbs-Duhem equation for each phase that also contains these parameters. Thus, if these n + 2 equations contain n + 2 parameters, these parameters can be determined (at the temperature in question) from the phase diagram alone. If the average number of parameters in each expression for the activity of a given component in a given phase is V then there will be 2nV parameters involved. Equating 2nV to n + 2 shows that, for n + 2, V = 1. If the temperature dependence of each parameter were to be expressed in some explicit form one could use equilibrium conditions at a number of temperatures to increase V. The situation is much improved when the two phases in equilibrium are structurally similar. It can then be assumed that, stably or metastably, two phases will become one at higher temperatures. Thus the number of parameters involved becomes nV instead of 2nV. Hence, V = 2 for n = 2 using only one temperature. (It is implied here that the activity expressions used are valid over the entire composition range.) In this investigation only the equilibrium of two structurally similar, two-component phases (miscibility-gap systems) will be considered. The various proposed solution models will be applied to a number of these systems and the results compared with available experimental results. All of the analytic expressions that have been proposed for the free energy of mixing of a two-component system are of the form where ?Gmix is the free energy of mixing per mole of solution, N1 and N2 are the mole fractions of components 1 and 2, respectively, and f(Ni, T) is some function of composition and temperature. In the "ideal" solution model f = 0. In the "regular" solution model f = a constant. Since these two models permit only a symmetric equilibrium diagram they will not be considered further here. The simplest model that permits a nonsymmetric miscibility envelope is the so-called "subregular" solution model proposed by Hardy.1 This model gives where the Ci(T) are functions of temperature only. The same expression for f is obtained from the "linear a function" model proposed by Darken and Gurry2 and applied to miscibility-gap systems by Wriedt.3 This model requires that the a function defined by be a linear function of composition (yi is the activity coefficient of component i). This model is not purely hypothetical for it has been found2 to hold true for a number of systems. It is readily shown3 that the f(Nl, T) obtained from this model is of the form given in Eq. [2]. It will be noted that the subregular solution model contains only two parameters and hence both of them can be determined at any desired temperature below the critical temperature, Tc, for a miscibility-gap systems in the manner described previously. At T, the two constants can be determined by equating the second and third derivatives of ?Cmix with composition to zero. Another two-parameter model was proposed by Lumsden4 who set

Jan 1, 1967

By G. F. Bolling

Single crystals of each metal were deformed at 77°K and heated at constant rates, variously in the range 0.125" to 4o°Kper min from 77" to -390oK, while being monitored in an X-ray diffractometer. Changes in diffraction-peak heights and line breadths were used to ascertain the temperature ranges of recrystalliza-tion. The results were subjected to the analysis of nicholas&apos; in order to obtain the rate-controlling activation energies,Q. In this analysis no recourse to a separate and distinct nucleation stage is required and the results of studying recrystallization proved consistent with the hypothesis of a constant number of nuclei or equivalent hypotheses. The values Pb = 5.5 ± 0.5 keal per mole Zn ~ 7.5 Sn - 5 Bi - 9. 5 correspond for lead, zinc, and tin to activation energies obtained elsewhere for grain boundary migration, and for bismuth and lead to previous studies of re-crystallization by Barrett.6 This correlation allows the conclusions that interference from recovery was minimal and that the observed recrystallization rates in these pure metals are effectively governed by grain boundary migration. Good agreement was not found between the results of this kind of study in zone-refined aluminum and previous work; and supplementary isothermral experiments involving hardness tests and metallography did not resolve the discrepancy. Nevertheless, at least a range,Q = 11.5 ± 2 keal per mole, can be assigned to the activation energy for boundary migration in aluminum. An experimental study of one aspect of the recrystallization process is presented here for four metals of different crystal structure. The metals chosen for study were all zone-refined to reduce impurity effects, but the attendant high purity presented a difficulty. For any reasonably high driving force a "re-crystallization temperature", TR, is in the range of 0.25 T,, where T, is the absolute melting point, and study was therefore restricted to lower temperatures. An X-ray technique under constant heating-rate conditions adequate above 90°K was devised for the study; in consequence, a newer type of analysis following Nicholas1 had to be used to obtain quantitative information about activation energies. The standard methods of studying recrystallization have involved the comparable analyses of Johnson and Mehl2 and Avrami3 which are reviewed by Burke and Turnbull.* The general analysis4 which is applied only to isothermal studies using any of various investigative techniques states:

Jan 1, 1968

By M. B. Mirza, F. D. Wright

Models of photoelastic material were made to simulate a mine roof that had cracked over the edge of the pillars and at the center of the span. Models were restrained from moving laterally outward so they acted as flat arches. Uniform loading was approximated by loading the models along the bottom at eight points spaced equally along the span. It was found that for models with depth to span ratios of 1:3 to 1:6, the maximum stress at the top of the center crack could be calculated directly by the following formula: Elastic stresses in mine roofs composed of sedimentary beds are usually computed by assuming that the immediate roof bed acts as a fully restrained beam uniformly loaded by its own weight and by overlying strata. Very little work has been done to analyze stresses in roof beds or beams which contain vertical (normal to the span) or nearly vertical cracks. Yet every mining engineer has walked safely under roofs that show such cracks. As far back as 1933, Bucky&apos; made model studies of the effect of vertical cracks on the behavior of horizontal strata. He did not make any analysis of the stresses but did show that a cracked beam will stand safely under certain conditions, and also showed that a beam restrained at the ends can crack over the supports and in the middle without collapsing as long as the ends of the beam are not free to move laterally outward. The beam, or rather, part of the beam, acts like a flat arch and supports itself by pushing outward at its supports. In 1941 Evans2 treated analytically the problem of a beam cracked along so many planes perpendicular to the axis of the beam that no tensile stress can operate. He named this type of beam a "voussoir-beam" by analogy to the voussoir-arch. In 1962 ~a~cocks~ modified Evans&apos;s solution by including the effect of the shear stress component of the resultant force at the abutment. This paper gives the results of a photoelastic study of the stresses in a beam containing vertical cracks in the center of the span and over the supports. A

Jan 1, 1963

By M. R. Geer, J. D. Davis, H. F. Yancey

ALTHOUGH the mechanical cleaning of coal is carried out at plants on the surface, preparation is actually begun at the face in the mine. Here the character of the coal and the amount, character, and distribution of the impurities within the bed may be seen. Blasting methods, dust-allaying procedures, location of mining cut with respect to bands of impurity, and the practice of discarding segregated impurities underground, all have an important bearing on the successful operation of surface cleaning units. The most important single characteristic of both coal and its associated impurities from the standpoint of cleaning is specific gravity. Other characteristics related in one way or another to the preparation , of coal are rank, petrographic composition, structure and hardness, and friability. These and still other coal properties are discussed in the first section of this chapter and impurity characteristics in the second. COAL CHARACTERISTICS RELATED TO PREPARATION Rank As a result of work done over a period of several years by committees of the American Society for Testing Materials and the American Standards Association, standard specifications are now available showing the &apos;classification of coals according to rank and quality of grade.&apos; The term "rank" expresses the degree to which the original coal-forming material has been changed by metamorphism through successive stages from peat to anthracite. Table 1 shows the classification of coals according to rank as devised by the committees of the organizations mentioned. The basic scheme of classification for the higher-rank coals is according to

Jan 1, 1943