Search Documents

By J. L. Green

Virginia-Carolina Chemical Corp., in its Florida Operations, uses both roller mills and ball mills in dry grinding of phosphate rock. The roller mills have been in operation since 1954 in the Mining Department. The ball mills were installed and put in operation in 1960 in the Harding Concentrate Superphosphate Plant. The roller mills in the Mining Department are used to grind phosphate rock for outside customers. This involves short notice orders of varying grinds, grades and types of rock. The ball mills grind phosphate rock for use in V-C's own phosphoric acid and concentrated superphosphate plant. These mills grind generally two types of rock for one grind. In 1959, a 10% speed-up was made in the operating speed of the roller mills. This paper deals with the operational gains and resulting cost savings which evolved from this speed-up, and compares the present operations of the roller mills and of the ball mills in grinding phosphate rock. In January 1959 it was decided to determine the feasibility of reducing the grinding cost on the roller mills, per ton of rock ground, by speeding up the mill 10%. At this time, one mill was completely reconditioned so it would be in top condition. Extensive tests were then run both before and after the mill speed-up to determine the resultant cost savings. These tests showed that, due to this 10% speed-up, the mill capacity was increased approximately 20% and grinding power costs per ton were reduced approximately 10%. Table I shows the results of these tests. Each test run actually represents several of the same type rock and grind, averaged together. Each test run lasted approximately three hours. The validity of these runs has been confirmed by subsequent operation in grinding over 1,000,000 tons of phosphate rock. Accurate records have been kept on power consumption and repairs as well as tons produced. Two types of feed rock were used for the tests — pebble phosphate rock and flotation phosphate concentrate rock. The pebble phosphate rock size is approximately 80-90% plus 20 mesh. The flotation concentrate phosphate rock size is approximately 15% plus 20 mesh and 95% plus 100 mesh. The same two types of rock feed were used for all the test runs. Test Nos. 1, 2, and 3 were run at the original mill speed of 85.5 rpm on the vertical shaft. Test No. 1 was run with a feed of high grade flotation concentrates; the desired fineness attempted was 70% passing 200 mesh. Tests No. 2 and No. 3 were run with a feed of low grade pebble. Test No. 2 was run for a desired fineness of 70% passing 200 mesh. Test No. 3 was run for desired fineness of 50% passing 200 mesh.

Jan 1, 1963

By D. H. Gurinsky, D. G. Schweitzer

The empirical equilibrium constantsd the heat of reaction for the reduction have been determined from 300° to 500°C. The mechanisms of the oxidation of uranium and magnesium from dilute bismuth solutions have been investigated. The kinetics of some of the reactions were affected by air adsorbed on the uranium oxides. THE Liquid Metal Fuel Reactor studied at Brook-haven National Laboratory uses a solution of uranium in bismuth as the fuel. Corrosion and stability problems require that the fuel solution contain corrosion inhibitors and deoxidants. Of the additives tested, magnesium has been found to be the best deoxidant and zirconium the best corrosion inhibitor in bismuth. Some experiments1 indicate that magnesium may play a secondary role in increasing the effectiveness of zirconium in inhibiting corrosion. The work reported here was intended to determine the relative concentrations of Mg and U required to prevent oxidation of the uranium fuel in the event of an air leak. In addition, an attempt was made to identify some of the mechanisms of the oxidation and reduction reactions occurring in the liquid bismuth solutions. EXPERIMENTAL Apparatus and Procedure—The equipment shown in Fig. 1 was designed so that the reaction kinetics could be studied as functions of temperature, melt composition, pressure, and flow rate. At the start of a run, the 10-liter bell jar (F) is removed by opening the bottom Dresser fitting (L), and the bismuth and additives are placed in a pyrex crystallizing dish (I). The bell jar is replaced, the system is evacuated to 10-5 to 10-6 mm Hg and then the heater (J) is turned on. When the selected temperature is reached, the oxidizing gas is admitted to the system to the desired pressure as read on the manometer (D). Gas is introduced through the slide tube (Q) which has a pyrex frit (R) sealed to its bottom. Stirring is accomplished by immersing the end of the tube in the melt. To maintain a constant pressure under flow the input and evacuation rates must be equalized. To obtain this condition stopcock (C) is closed and flowmeters (B) are matched. The reaction is "stopped" by closing the inlet flowmeter and quickly evacuating the system. To obtain a liquid metal sample, the system is evacuated with the sampler positioned near the surface of the liquid. The sampler, Fig. 2, is then immersed until its thermocouple reading matches thermocouple (G) Fig. 1. The system is then pressurized with helium which forces the solution through the frit. Twenty to 30 min elapsed between the time the system was evacuated and sampled. During evacuation and pressurization of the system, the temperature variations did not exceed ± 5°C. While bubbling occurred the temperature remained constant to within 1/2 oC. The volume of the equipment was determined by adding a known volume of air at atmospheric pressure to the evacuated system and noting the resulting pressure.

Jan 1, 1962

By E. F. Adkins, R. W. Douglas

The variation of the spectral emissivity of osmium and ruthenium with temperature can be expressed by the following relations: DURING a study of the sintering characteristics of osmium and ruthenium, discrepancies in the previously accepted melting points of the metals were noted. The melting temperatures had not been measured at the time of the work, but were estimated in the literature as 2700°C for osmium and 2450°C for ruthenium.' A recent investigation by Baird2 has shown the melting temperatures of osmium and ruthenium are 3000" and 2250° C, respectively. In the present work, osmium bars sintered at temperatures as high as 2900° C showed no evidence of melting, whereas ruthenium showed definite evidence of melting at temperatures as low as 2250°C. In view of the apparent discrepancies, the melting temperatures of both metals were determined. The spectral emissivities of both metals were determined as an aid to studies of the sintering characteristics of these metals. MATERIALS AND PROCEDURES The materials used in these studies were metal powders supplied by Englehard Industries, Inc., through the courtesy of The International Nickel Co. Analytical data from three laboratories, although not in complete agreement as to the purity of the material or the major impurity elements, indicated that the maximum impurity levels were 0.5 and 1.0 wt pct in osmium and ruthenium, respectively. The metal powders were pressed to 1/4 by 1/4 by 6-in. bars at 20Tsi using carbon tetrachloride as a lubricant. The pressed bars were presintered 1 hr at 1200°C after heating 1 hr at 400°C. The presintered densities of the several bars of the metals ranged from 65 to 80 pct of ideal density. Specimens were self-resistance heated in a vacuum sintering bell. Temperatures were measured with an L&N, disappearing filament optical pyrometer. True temperatures were read at the base of an 0.30-in.-diam, 0.150-in. deep hole drilled into the center of a presintered bar. Apparent temperatures were read from the surface of the bar adjacent to the hole. MELTING POINT DETERMINATION The melting temperature of the metals was determined as the temperature at which a slight additional increase in current through the specimen resulted in a reduced temperature at the base of the hole. The apparent reduction in temperature is a result of the liquid metal filling the hole, thus altering the black-body conditions. The melting points of osmium and ruthenium, based on three deter-

Jan 1, 1962

By Herty, C. H.

Three distinct processes take place during the conversion of iron ore to steel. First: the raw ore is reduced to metallic iron in the blast furnace and during this reduction certain constituents are dissolved in the iron, either through the solution of a solid into a liquid phase, as in the case of carbon, or by reduction of an oxide existing in the slag to the metallic element of that oxide, with subsequent solution of the metallic element in the iron. Thus by the process of solution and reduction, a pig iron results which contains about 4 per cent carbon, 1 per cent silicon, 1 to 2 per cent manganese, 0.1 to 0.4 per cent phosphorus, and 0.03 to 0.10 per cent sulfur. To obtain a sufficient yield of iron from the ore it is necessary that the reducing process be carried as far as possible, with the result that the impurities mentioned accompany the reduced iron. Second: to convert this iron into steel it is necessary to oxidize a part of the iron in eliminating the impurities to the extent desired for the particular product being made. In eliminating these impurities by oxidation a certain amount of iron oxide (FeO) dissolves in the steel. This dissolved FeO reacts with the metalloids, except sulfur, and to eliminate them to the desired extent it is necessary to leave a considerable amount of FeO in the metal. The reaction of iron oxide with silicon, manganese, and phosphorus results in the formation of the oxides of these elements. The oxides enter the slag and the extent of elimination of the elements depends on certain equilibria between the slag and the metal. The reaction of FeO with carbon results in the formation of the gases CO and CO, which, after saturating the metal, pass into the furnace gases. Third: after the iron has been purified to the desired extent as far as the elements listed are concerned, it is necessary to deoxidize the bath to remove the FeO, which is the vital factor in gas formation as the steel solidifies.

Jan 1, 1957

By N. A. D. Parlee, I. D. Shah, W. C. Phelps

THIS note reports on a continuation of a program on the thermodynamics of Fe-S-X systems in the "steel-burning" temperature range begun by Bock, Barloga, and parlee.' Small coils of 0.039-in.-diameter pure iron (Ferrovac-E) wire were equilibrated with Fe-S-0 melts in ingot iron crucibles under argon at 1324°C in the assembly shown in Fig. 1, the lower part of which was heated in a large Globar furnace. Fig. 1 shows (R) the coiled iron wire sample, (M) the Fe-S-0 melt prepared from desired proportions of ferrous sulfide and ferric oxide, (K) the iron crucible, (I) a mullite guide tube, (J) an alumina crucible, (L) alundum sand, (N) crushed mullite, (Q) hollow cylinders of K30 brick, (C) a steel rod, (B), (El, (F), (G), (P), and (O), details of brass water-cooled head, and (H) a mullite tube 2-3/4 in. ID and 26 in. long. The rod (C) bearing the sample could be removed at will and be replaced by a tube for sampling the melt, or by a thermocouple for comparing the melt temperature with a control thermocouple not far from the 2-3/4-in. mullite tube. After equilibration the iron coils were treated with acid to remove the outer layer of metal and then they were analyzed for sulfur by a standard combustion method. The melt samples were analyzed for oxygen by a variation of Lander's2 hydrogen-reduction method for mattes, and for sulfur by the ASTM combustion-iodometric method NO. E 30-47. When the results of some forty-two runs were examined it was found that the sulfur and oxygen contents of the equilibrated melts showed good consistency, in that the plotted compositions fell along the smooth curve shown in Fig. 2. The points on this curve represent the experimental compositions of melts in equilibrium with ?-iron (Fe-S-0) solid solutions. These solid solutions are saturated with sulfur and oxygen with respect to the melt and therefore have the same sulfur and oxygen activities as the melt. The curve drawn through the points therefore delineates the ? liquidus. It falls in such a position as to roughly confirm the liquidus curves of Hilty and crafts3 at 1200" and 1300°C which are

Jan 1, 1965

Jan 1, 1967

By M. W. BERNEWITZ

ALL live producers and manufacturers of metals and alloys are investigating new uses for their products. The tin and tin-plate industry is no exception. One-third of all the new tin mined and refined is consumed in making tin plate. Several billions of cans are each year made from tin plate for the preservation of nearly 200 kinds of food. There are more than 500 tin-plate mills or individual stacks in the United States, which country makes more tin plate than all other countries combined and exports large quantities. As much as 1,800,000 tons of till plate has been made in a year in this country, and 28.000 tons of tin has been used in this period for this purpose. In sonic years a third of the till is so consumed; in 1933 it was half of the supply.

Jan 1, 1935

By A. M. Gaudin

THE purpose of ore dressing is to separate the rough ore into one or several valuable concentrates and a discarded tailing. The first step is to crush the ore so that the resulting particles may be individually valuable or worthless. The next step generally has to be a sizing operation, because the property by which concentration is effected depends on the size of the in-dividual mineral particles as well as on their physical properties. These two effects may cancel each other if a preliminary sizing is not resorted to. Sizing is accomplished by screening or classifying. Screening depends almost solely on the dimensions of the particles; classifying depends also on the specific gravity of the particles and the viscosity of the settling medium in which the classifying operation is conducted. Classification, therefore, is to a certain extent a con-centrating operation as well as a sizing operation. Before the days of concentration by flotation, the available screens were mechanically poor. As a result classification was employed for sizing in the range. of comparatively coarse sands (table feeds). In recent years, the advent of stage-grinding to flotation size has brought about the development of good screens, which are more economical than classifiers down to about 20, -mesh. With decreasing size at which separation is to be made, screens become increasingly uneconomical, while classifiers become increasingly economical. The line of demarcation between the respective fields of screening .and classification is, therefore, fairly sharp. With the development of processes of concentrating finely comminuted ore, the need for classifiers or other sizing devices operating so as to make efficiently a split at a very fine size has become increasingly apparent. Such classifiers might be termed de-slimers, from the fact that they separate a material having a slimy ap-pearance from one having the characteristics of a sand. Sizing-tests are carried on by means of testing sieves, the finest of which have apertures of about 1/500 of an inch. The 200-mesh sieve, which has an average open-ing of 0.0029 linear inches is generally considered the limit of practical test-sizing. As a result, little is known of minus 200-mesh material and the advantages of classifying concentrator feeds within the minus 200-mesh range has been overlooked. An extension of the -present sieve scale beyond the 200-mesh screen is given in Table 1.

Jan 2, 1927

By H. C. Meister

THE zinc-smelting industry of the United States has grown very rapidly in recent years and bids fair to outrival that of all other countries in the future. On account of the geographical situation of the chief ore-supplies, the industry may be divided into two main groups, the eastern and the western. The eastern and older group includes the works of Pennsylvania, New Jersey and Virginia, which practically control their own ore-supply. The western group includes the works of Illinois, Missouri, Kansas, Wisconsin and Indiana, which do not control their own ore-supply, but are compelled to buy the ore in the open market. It is for this reason that the western zinc-smelting industry has been undergoing continual changes since its inception 40 years ago. During the early discoveries of lead- and zinc-ore in the lead- and zinc-districts of Wisconsin and northern Illinois, the zinc-ore (sinithsonite or " bone " as the miner calls it) had no value and was considered waste; but later, when this ore was found in large quantities, it attracted the attention of metallurgists, which finally resulted, during the early sixties, in the building of the Matthiessen & Hegeler Zinc Works at LaSalle, Ill., the pioneer zinc-works of the West. A few years later, zinc-ore was discovered associated with the lead-ore in Jefferson county, southeastern Missouri, which started the industry at Carondelet or South St. Louis. Still later, the discoveries of zinc-ore in the lead-ore region, first' at Granby and then around Joplin, lead to the introduction of the industry in the southwest Missouri and Kansas districts. At first the development of the industry was slow, but it progressed steadily and it is now one of the leading metallurgical industries of the middle West.

Jan 1, 1905

Jan 1, 1970

By C. E. Gerity

Near Bunker, Mo., in the New Lead Belt, Ozark Lead Co. operates a 6000 tpd lead-zinc mine. Mined ore is transported to the surface in three mechanized and automated steps. The mine is developed by a rectangular-shaped sublevel haulage drift 15 ft high by 28 ft wide, driven on strike below the ore zones. Ore transfer raises were driven from the sublevel at locations near the shaft, 1500 ft distant, and on subsequent 1000 ft centers. These 6 x 5-ft raises are slashed to obtain maximum storage below dump points. These dump points are located on each mining level and are of steel and concrete construction. Spiral 12 X 24-ft inclines driven from the sub-level provide access to these levels for equipment and mine utilities.

Jan 11, 1972

By Dunbar D. Scott

The development in the perfection of mine-surveying instruments has been by no means rapid, as it has depended somewhat on the details of construction borrowed from astronomical and geodetic theodolites, largely on the restrictions laid down by mining companies and the prejudices of mine managers themselves, but more than all on the methods used in conducting surveys and the importance attached thereto. Mine-surveying, in some form or other, has been practiced from the very earliest times; but it has never kept pace with the other branches of surveying, or even with the art of mining itself, and cannot be recognized as an exact science until shortly before the beginning of this century. The works of Hero of Alexandria, who lived in the second century B.C., are still extant, and contain descriptions of a rectangular sighting-instrument, which he invented and called a diopter. His improvement upon this simple construction, which possibly he devised for use in the Greek mines for rough leveling-purposes and for laying out any angle, must be considered, says Hübner," as the origin of the highly perfected theodolite of to-day. Whether this instrument came into general use during the first centuries of the Christian era, is not recorded; in fact, no writer undertakes to tell how mine-surveying was conducted until 1556, in which year Agricola expounds the principles of mining and metallurgy in his De Re Metallica, devoting the entire fifth chapter to the practice of mine-surveying (see Fig. 1). In mediæval times those who possessed any knowledge of engineering skill made strenuous effort to keep their art a secret, partly on account of the miners' proverbial conservatism and partly for their own personal aggrandizement, and were, in

Jan 1, 1899

By H. E. Elliott, R. S. Busk, A. T. Peters

One of the problems of the fabricator of metals and alloys is the propensity of some composition rarnges toward abnoermal grain growth during certain stages of fabrication. In this respect magnesium alloys are no exception among alloys. Fortunately, convenient foundry control methods have been developed by which the abnormal grain growth possible in certain magnesium-alloy castings can be suppressed. An unusual characteristic of magnesium alloys, however, is that castings of some composition ranges are subject to local grain growth during heat-treatment without the necessity of intentional mechanical stressing of the part prior to heat-treatment. This effect occurs only under certain critical casting conditions, and only in certain alloys of greater than about 8.5 per cent aluminum content, such as C alloy (Mg, 9 per cent A1, 2 Per cent Zn, 0.2 Per cent Mn) and G alloy (Mg, 10 per cent Al, 0.2 per cent Mn). The first observation of this phenomenon in cast magnesium alloys occasioned much surprise, since it is not observed in other meta1s- Jeffries and Archer1 have stated that "the grain size of cast metals, provided they have not been plastically deformed, cannot be changed by heating below the melting point." The study of the conditions leading to abnormal grain growth in cast magnesium alloys, and of the mechanism of this phenomenon, has led to some very interesting observations. Perhaps the most significant of these was the observation that stresses originating from cooling contraction in magnesium-alloy castings are the only stresses necessary, under certain conditions, to cause local recrystallization and subsequent grain growth in the casting during heat-treatment. Before recent developments, this phenomenon of abnormal local grain growth Was a definite problem in the production foundry on C alloy sand castings. Illustrated (Fig. I) is a picture of a casting scrapped because of this defect. A mottled effect is produced in coarse-grained areas by suitable etching solutions. The properties of metal in the affected area are much impaired by such grain coarsening. Ultimate tensile strengths of half the normal value have been measured in metal of this nature. In this paper are described the techniques that have been developed by The DOW Chemical Co. for studying, and in large measure solving, this production problem. Also discussed are studies of the mechanism by which excessive grain coarsening occurs, and the fundamental conditions that produce this effect. The abnormal grain growth discussed in this paper will be referred to as "germinasium since this term has been definedl as any process leading to an abnormally coarse grain size. This paper deals only with abnormal local grain growth that may occur during the solution heat-treatment of certain magnesium-alloy castings, as dis-

Jan 1, 1945

By C. Crussard, R. Tamhankar

It is the policy of The Metallurgical Society to provide, in the TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AIME, a prompt and accurate medium for publication of reports of significant new research in both the scientific and engineering aspects of metallurgy. Papers submitted to the Society are judged by competent reviewers accord-ing to established criteria for technical merit, accuracy, originality, and presentation. STAFF: Editor, Gerhurd Derge Carnegie Institute of Technology Schenley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Staff Coordinator, James J. Burke THE METALLURGICAL SOCIETY: W. R. Hibbard, Jr., President; J. C. Kinnear, Jr., Past-President; John Chiprnan, Vice President; T. D. Jones, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: A. W. Thornton, Chairman; Dennis Carney, John Chip-man, J. C. Fulton, J. H. Hollomon, H. H. Kellogg, A. E. Lee, R. Maddin, J. D. Sullivan, and D. Swan. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division: T. B. King, Chairman; S. J. Dickenson, R. P. Hermsdorf, R. Schuhmann, Jr., and P. T. Stroup. Institute of Metals Division: Robert Maddin, Chairman, F. Lincoln Vogel, Jr., Vice-chairman, W. A. Backofen, R. W. Balluffi, J. H. Bechtold, M. B. Bever, R. S. Busk, C. G. Goetzel, Paul Gordon, C. D. Graham, .Jr., Robert F. Hehemonn, R. I. Jaffee, F. E. Jaumot, Jr., Irving R. Kramer, A. J. Lena, Harold Margolin, C. J. McHorgue, Russell A. Meussner, J. B. Newkirk, H. W. Paxton, G. E. Pellissier, I. S. Servi, Alan U. Seybolt, A. J. Shaler, and Jack Washburn. Iron and Steel Division: J. C. Fulton, Chairman; T. B. King, F. C. Langenberg, W. 0. Philbrook, and T. 0. Winkler. Published bimonthly by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc., 29 West 39th Street, New York 18, N. Y. Telephone: PEnnsylvania 6-9220. Subscription $20 per year for non-AIME members in United States and North, South, and Central America; $25, foreign; $5 for AIME members. Single copies, $4.00, single copies foreign, $5.00. The AIME is not responsible for any statement made or opinion expressed in its publications . . . Copyright 1958 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AIME New York ... Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts... Second class postage paid at New Yark, N. Y., and Ann Arbor, Mich. Volume 212, Number 6.

Jan 1, 1959

By Malcolm T. Hepworth

RECENT interest in thermoelectric devices has been directed toward studies of the properties of thermoelectric materials of semiconducting solid compounds with little attention given to ionic and semiconducting liquids such as aqueous solutions, fused salts, and mattes. One type of thermoelectric system is the thermocell: a nonisothermal galvanic cell with two identical electrodes at different temperatures connected by an electrolyte bridge. An electromotive force, v, is generated which is a function of the electrode reactions and the properties of the electrolyte according to the Eastman' equation: where S* is the entropy change of the system arising from the electrode reactions and by heat transferred by ion migration and by thermal conduction. The quantity nF is the product of equivalents passed and Faraday's constant. A value of S* of 23.06 cal per "C is equivalent to 1 mv-Faraday per "C. The symbol, a, is used for dV/dT in analog to the See-beck coefficient of solid-state thermoelements. de Bethune2 has calculated the temperature coefficients of the electromotive force of a large number of nonisothermal aqueous cells from measurements on the nonisothermal temperature coefficients of the standard hydrogen electrode, combined with data on the isothermal temperature coefficients of half-cells tabulated in the literature. Values of these coefficients (a) in de Bethune's compilation ranged up to 3 mv per C. In particular he reported a value of +2.059 mv per "C at 25'C for the cell: Fe (aqueous, unit activity) (aqueous, unit activity) written for the hot-electrode reaction. The positive sign indicates that the hot electrode is positive (an "n-type thermocell"). In analog to a solid-state p-n system, it would be possible to couple two thermocells together to form a system in which the figure of merit could be calculated by adding the temperature coefficients according to the relationship described by offee:' where a is the Seebeck coefficient in volts per "C, p is the specific resistivity in ohm-cm, and K is the thermal conductivity in watts per cm "C. Even though ionic systems have rather high electrical resistivities compared with semiconducting and metallic systems, it was felt that a preliminary study of one ionic system should be made to establish some basis for evaluating the possibility of a p-n thermocell for energy conversion. Accordingly the Fe", Fe"' system was studied as a possible component for a p-n system. A glass system was constructed consisting of two vertical water-jacketed tubes connected by a horizontal tube, Fig. 1. Platinum-black electrodes 1 cm by 1 cm in dimension were inserted in each vertical tube with thermometers to register the electrode-compartment temperatures. The temperature of the electrode compartments was controlled by circulating water from thermostatted baths around the electrode compartments. The electromotive force of the cell was then read by a potentiometer for zero current as a function of the temperature of the hotter electrode. Current output of the cell for varying external loads was also measured. The cell resistance was measured by means of a bridge circuit with 10,000 cps signal and oscilloscope. Resistance measurements were converted to specific resistivity by calibrating the cell with a solution of known conductivity.

Jan 1, 1965

Elected Died 1903 * ADAMS, CHARLES C. 1905 1884 *ADDY, MATTHEW 1896 1894 *ALLFN R B 1896 1874 *AMIOT, H 1892 1886 *AMSLER, CARL 1894 1895 *ÅNGSTROM, CARL 1901 1895 *ARMSTRONG, JOHN F 1898 1882 *ARNOLDS, HUGO 1886 1875 *ASHBURNER, CHARLES A 1889 1872 *ASIIBURNER, WILLIAM 1887 1883 *ATKINS, C M , JR 1885 1897 *AYERS, WILLIAM 1898 1885 *BABCOCK, GEO H 1893 1884 *BAILEY, EDWARD 1889 1880 *BAILEY, JACKSON 1887 1900 *BALLOU, FRANKLIN 1903 1886 *BARNES, F W 1892

Jan 1, 1910

By N. A. Gjostein

From their study of the anisotropy of grain boundary mobility in aluminum, the authors conclude that tilt boundaries have a higher mobility than twist boundaries because the atomic misfit at the pure-twist boundary is relatively small compared to the misfit at a tilt boundary for a given amount of misorientation. If this is true, then one would expect a twist boundary to have a lower grain boundary energy than the corresponding tilt boundary. Fig. 6, taken from the work of Gjostein and Rhines,10 shows that this is indeed the case for [001]-cu tilt and twist boundaries in the high-angle region, thus lending support to the authors' conclusion.

Jan 1, 1968

By Edward H. Williams

IN the middle of the eighteenth century John Frazier and wife, Sarah Ingraham, removed from Boston, Mass., to Philadelphia, Pa., where he was held in such esteem that we find him one of the Committee which arranged the ball at Washington's inauguration. Their son John. Nalbro Frazier, was prosperous in his mercantile career and fortunate in his wife, .Anne West; who was an important personage in the early life of Professor Frazier. This cultured lady brought into the family an atmosphere of religious enthusiasm, of thoroughness and: of unity of purpose. Her son, Benjamin West Frazier, inherited her traits and displayed them during a. short and active life. Like his father, he engaged in mercantile pursuits, and was a member of the firm of Zimmerman, Frazier & Co. In their interests he lived for a short- time in Montevideo, and on his return married Isabella Zimmerman, a daughter of the head of the firm. Their happy married life was cut short by the death of Mrs. Frazier shortly after the birth of the subject of this sketch which, occurred October 3, 1841. Mr. Frazier did not long survive her, and left his orphaned sons to, the care of his mother, from whom he had inherited a lovable and deeply religious nature, an : artistic temperament and a capacity for thorough work. Whatever of these traits fell by inheritance to these children were strengthened by the influence of their grandmother, and. the purity of mind, the delicacy of sentiment, the refinement of honor, which characterized. Professor Frazier, are due to Anne West Frazier, and are generally present in the characters of all of gentle blood who have been under the sole and immediate influence of a mature and refined woman. Professor Frazier was educated at the Episcopal Academy in Philadelphia, and passed thence through the University of

Sep 1, 1905

By AIME AIME

American Institute of Mining Engineers. (Organized in 1871, and Incorporated in 1905.) OFFICERS. For the year ending February, 1906. Directors JAMES GAYLEY (President), R. W. RAYMOND (Secretary), FRANK LYMAN Treasurer). T. A. RICKARD NEW YORK, N. Y. CHARLES H. SNOW NEW YORK, N. Y. R. W. RAYMOND NEW YORK, N. Y. (Terms expire February, 1906.) JAMES GAYLEY NEW YORK, N. Y. FRANK KLEPETKO NEW YORK, N. Y. FRANK LYMAN NEW YORK, N. Y. (Terms expire February, 1907.) JAMES DOUGLAS NEW YORK, N. Y. JAMES F. KEMP NEW YORK, N. Y. ALBERT R. LEDOUX NEW YORK, N. Y. (Terms expire February, 1908.)

Jan 1, 1906

By David H. Browne

(Pittsburg Meeting, March, 1910.) NICKEL has always been a fruitful mother of problems. Previous to the year 1906 nickel was regarded as an element replacing iron in copper-mattes, and it was believed that the same laws which governed the elimination of iron could be applied-to nickel. This conception has lately undergone a complete change, and nickel in all its stages is now regarded as an element replacing copper; in other words, copper-nickel is considered now as two elements, but as one metal. When we commenced our investigations on Monel metal we made a great many experiments on the conversion of mattes, both high copper and high nickel. We studied closely the composition of the mattes and the changes produced by the blow. We found in all cases certain agreements which we believe are due to some law. Briefly stated, our conclusions are as follows 1. Nickel is not an element replacing iron in matte. 2. Nickel-copper alloys act in the matte-blow like one metal. 3. Nickel-copper alloys follow, during the matte-blow, exactly the same laws as govern. the behavior of copper alone. This brings up the question : What are the laws governing the production of metallic copper, and what are the relations copper to sulphur and iron during the Bessemer blow ?

Apr 1, 1910