Search Documents

By Ekin Güngor, Berkant Ozdemir, Erkan Bayrak, Serdar Ergün, Sedat Esen

"This paper presents the final wall blasting practices at Eldorado Kisladag Gold Mine in Turkey. Benchmark and improved wall control designs were explained in detail. Kisladag Mine has been implementing a high quality slope stability program on-site. The quality of pit walls is generally considered excellent, with very few wall failures being evident and with presplit hole barrels prominent in most areas of the pit. However, a minor scale slope failure occurred recently at the north-east section the pit. A project was initiated to diagnose the cause of the crest loss and evaluate ways to limit its effect on final walls. Final wall blasting practices and geotechnical designs were evaluated. The work presented in this paper showed that changes to the blasting and geotechnical parameters are required atthe north-east section of the pit. Geotechnical design changes were 10 m bench heights with 70 ° slope face angle at that specific area. Having implemented several geotechnical and blast design changes (elimination of the subdrill for the catch bench, appropriate primer location, more favorable blast tie-up and delays), the crest loss was minimized significantly (<1.5 m) (<5 ft)."

Jan 1, 2017

By Ching-Liu Wu, John Hawley, Andrew H. Liu, James Chai

The Hatch Mott MacDonald/Bechtel Joint Venture team is designer and construction manager for the 5.25-mile Tunnel Segment of the overall 16-mile Silicon ValleyRapid Transit Project, which extends the existing Bay Area Rapid Transit (BART) system southward from Fremont to San Jose. The Tunnel Segment includes twin boredtunnels, mined cross passages, and three deep station excavations situated in highlyvariable ground, high ground water table, and a dense urban setting with high-risebuildings adjacent to the largest excavation. This paper will discuss design challengesthat have arisen with the excavations and the proposed solutions.

Jan 1, 2007

By C. Laughton

Construction of a Deep Underground Science and Engineering Laboratory(DUSEL) is proposed under the auspices of the US National Science Foundation(NSF). DUSEL will provide scientists and engineers with a research facility capable of supporting a broad spectrum of fundamental and applied research deep in the earth’s crust. Research partners are physicists, biologists and geoscientists. DUSEL research calls for the construction of a network of shafts, tunnels and caverns that will provide laboratory facilities at depths of up to approximately 2 kilometers. The Project is still in the planning stages but, the initial experimental program is taking shape and conceptual designs have already been developed at two hard rock mine sites. This paper discusses the overall program and key engineering tasks being developed to support the construction of deep, large-span caverns. These caverns will house a new generation of physics experiments. As currently scoped, the experiments call for the excavation of permanent caverns with spans of up to 60 meters, sited at depths in excess of a kilometer.

Jan 1, 2007

By Max F. Lee, Warren A. Peck

The applicability of the Q-system [Barton et al. 1974] to Australian underground metal mines is discussed with reference to two common design issues: ground support for horizontal mine development, and assessing the stability of bored raises. Installed ground support in mine development is com-pared to empirical estimates using the Q-system and associated support capacity calculations. Data are graphically presented from 59 specially selected sites at 15 contributing mines. The actual performance of large-diameter raise-bored shafts is also compared to empirical stability assessments using a modified version of Q (Qr, after McCracken and Stacey [1989]). Lower-bound Qr values are plotted against raise diameter for 47 selected sites at 23 mines in Australia and Papua New Guinea. The influence on Q and Qr of some geotechnical aspects of the Australian landscape, the dynamic nature of mines (compared to civil construction), and occupational health and safety regulations are discussed. Stability and support assessments that are based just on Q or Qr are not always conclusive. It is often necessary to consider other rock mass parameters, the regulatory environment, and risk issues. These results are interim; further data collection and analysis are required with regard to comparing actual performance versus empirical assessments.

Jan 5, 2007

By J. J. Forbes

This publication is a revision of the first of a series of four Miners&apos; Circulars originally prepared and issued in 19&apos;29 for use in a course of training designed to prepare mine officials to organize men for rescue and recovery operations. These circulars were revised in 1937 and 1938 and again in 1948. This circular (Miners&apos; Circular 33) discusses mine gases and methods for detecting them. The second of this series (Miners&apos; Circular 34) gives instruction in Bureau of Mines methods of sampling and analysis of mine gases; the third (Miners&apos; Circular 35) describes methods and equipment used for protection against mine gases; and the fourth (Miners&apos; Circular 36) explains procedures used in sealing and unsealing mine fires and in recovery operations after mine fires or mine explosions.

Jan 1, 1954

By J. F. T. Agapito

OCI Wyoming mines two flat-lying trona seams that are 3- to 3.5-m- (10- to 11.5-ft-) thick, about10 m (33 ft) apart and 250-m- (820-ft-) deep at its Big Island Mine in Wyoming. Continuous miners and a yielding-pillar system have contributed to improvements in resource recovery and productivity. The use of yield pillars minimizes the stresses transmitted from the upper to the lower seam. However, yielding must not impact the good, long-term stability needed to prevent subsidence for a large portion of the mine beneath the Green River channel.

Jan 1, 2000

By R. Schulz, K. King

Concentrating Line 6 just went down again. The control room operator checks the graphic display. Only one piece of equipment shows an alarm. Clicking on the ball mill icon, he discovers the culprit was the low flow lube switch. The flow looks okay now, but it is the third time this week the switch has stopped the line. Maintenance is called, the switch replaced and the line is up running again. Sending the right person to the right spot immediately can save hundreds of hours of downtime every year. This paper discusses the principles behind implementing smart First-Out Fault Detection to dramatically reduce equipment downtime in new, or existing control system architectures. Methodologies are presented to maximize the system benefits, while minimizing development costs. Case histories are presented for a number of successful implementations in mineral processing plants.

Jan 1, 2001

By D. E. Andrews

The objective of this study was to investigate the environmental effects of slaking of surface mine spoils. To accomplish this, both field and laboratory programs were undertaken, supplemented by a thorough literature search. The field program consisted of drilling the highwall as well as test pitting in recent, two-, five, and ten- year-old spoil piles at four active mining sites in the eastern bituminous coal fields. Pertinent observations were made and samples collected for laboratory analyses which consisted of several standard geotechnical, agronomic, and geochemical tests. Durability tests utilized included jar slake, cyclic wet-dry, rate of slake, and slake durability tests. Correlation between field and laboratory portions was made- and results presented. The report is concluded with a discussion of the slaking process and associated environmental impacts, proposal of a preliminary classification system for use in premine planning, and presentation of management techniques to optimize the slaking process.

Jan 1, 1980

When it comes to safety in the mining and extractive industries, success is literally a matter of life and death. Anything short of perfection is not acceptable. In recent years, the mining industry in the United States has made tremendous strides in terms of health and safety for its workers. Part of that success has come with an increased focus on the issues of safety, an intense examination of procedures, liberal sharing of best practices and a focus on the synergy between safety, reliability and environment. During his closing keynote address of the Safety Management & System Reliability Conference in Minneapolis, MN on Nov. 15, Joe Driscoll, vice president of Great Basin Gold, showed a calendar from the coal fields in Pennsylvania from the early 1900s. The calendar marked the number of mine-related deaths each month. Some months, the number was as high as 50. It was an illustration of how far things have come, but there is still much more work to be done.

Jan 1, 2013

By V. Ross

"Bench-scale flotation tests play a major role in the geometallurgical process value chain. Despite their apparent simplicity, these tests pose pitfalls in terms of operation, as well as the interpretation and modelling of results. In this paper we highlight key aspects to consider in generating accurate and reproducible experimental results, and critically review some assumptions relating to the estimation of entrainment and froth recovery. We subsequently focus on first-order equations to model kinetics and propose a method that accounts more realistically for the decay in kinetics over the duration of a float, and the contributions of froth stability and hence mass pull. The method was applied to three case studies on platinum group metal (PGM) ores and matched or outperformed first-order, two-component models. Also, it allows for a deeper analysis of the integrity of the bench-scale flotation results. IntroductionGeometallurgy is a structured, multidisciplinary approach that integrates key data from the geological, mining, mineralogical, and metallurgical aspects of the value chain to construct spatial models of an ore deposit such that the overall economic benefit and sustainability of an operation can be optimized. Process geometallurgy is aimed primarily at enhancing metallurgical efficiency and plant throughput by the application of appropriate mining and processing strategies, as well as supporting production planning and operational strategies to reduce the impact of highly variable ores. With flotation being the dominant concentrating process in the mineral value chain, the bench-scale flotation test is an important characterization tool – a relatively cheap, simple, and rapid way to obtain key information about the ore and its amenability to economic extraction of valuable minerals. This includes the evaluation of different ore types and the implications of mineralogical composition and texture for comminution and floatability, the effect of the grinding environment on the liberation of minerals, the electrochemical environment in the pulp (Bradshaw et al., 2006), the screening of reagents to improve floatability (Ekmekci et al., 2003), and the role of hydrodynamics in the recovery of valuables and the entrainment of gangue (Amini et al., 2016; Wang et al., 2016). It is also a critical tool in auditing the performance of a flotation plant by hot floats, paving the way for concept and feasibility studies and providing essential data on kinetics for the purposes of scale-up, optimization, and simulation of flotation circuits."

Mar 1, 2019

By L. F. Willmott

The Bureau of Nines at Morgantown, W. Va., has been investigating, on a pilot plant scale, various methods of gasifying bituminous coal with oxygen and superheated steam to produce synthesis gas, as part of the broader program of finding new uses for coal. Differences in the pressure gasification methods used have depended on differences in the manner in which the pulverized coal is fed to the gasifier. One of the methods of feeding the coal that was investigated was the continuous, integrated coal-water slurry system. Goal and water were first mixed to produce a slurry; then the slurry was pumped through a heated coil. to evaporate the water fraction; the resulting steam was superheated, and some of it was separated so as to adjust the ratio of the residual steam to the coal fraction and make the resulting mixture suitable for partial combustion with oxygen in a pressure gasifier. Both before and during this reported3 developmental work it was necessary to make an extensive literature search into the technology of aqueous slurries in order to establish design criteria for the pilot plant and to correlate results of various phases of the work with that of other investigators, The pilot work coincided with the commercial development of a long-distance pipe- line for the transportation of coal as a coal-water slurry, and this fact tended to broaden the scope of the pilot plant work and the extent of the literature search. This bibliography is the compilation of the material that was collected.

Jan 1, 1963

By P. Walford, C. Mealin, D. Good

"The geology of the Ore Fault Ni-Cu deposit has been reinterpreted in the light of recent studies of the geology of the Neoarchean Bird River Sill Complex and the occurrence of economic Ni-Cu and Zn-Cu-Ag mineralization. The Ni-Cu sulfides are hosted by the lower of two parallel NNW-trending and moderately W-dipping mafic-ultramafic intrusions related to the Bird River Sill Complex. The bod¬ies intruded a bimodal volcanic suite consisting of weakly deformed mafic flows and felsic pyroclastic rocks. The mafic volcanic rocks are geochemically related to the MORB-type rocks of the Lamprey Falls Formation, and the felsic volcanic rocks are related to arc-type rocks of the Peterson Creek Formation. The original pyroxene- and olivine-dominated mineralogy of the sills has been replaced by variable ser¬pentine-amphibole-talc-carbonate assemblages.The Ni-Cu sulfide assemblage exhibits textures and geochemical signatures typical of orthomagmatic sulfide mineralization. The sulfide minerals are associated with cumulate layers of magnetic ferrochromite that range in thickness from a few to tens of centimeters. A later event of Zn-Cu-Ag sulfide mineralization associated with quartz veining and garnet-chlorite alteration along a fault that strikes north, dips vertically, and cuts all rock types. The mineralized fault is cut by the NE-trending Peterson Creek shear zone. Where the Ni-Cu and Zn-Cu-Ag mineralized zones intersect, remnant magmatic features such as amphibolite or cumulate ferrochromite bands occur within quartz veins or local chlorite alteration. The mixed zones contain a very unusual polymetallic assemblage of Ni, Cu, Zn, Ag, and platinum group elements (PGE)."

Jan 1, 2009

By S. A. Bortz

This report presents the results of an extensive laboratory testing program to determine the physical properties of shotcrete including the use of fast-set agents, controlled set cements, and both wet and dry shotcreting equipment. Shotcrete was placed under simulated field conditions using the dry and wet processes. Mechanical properties obtained for accelerated and nonaccelerated shotcretes include compressive, flexural, and shear strength, elastic modulus and Poisson&apos;s ratio, and shear and tensile properties of shotcrete bonded to coal, sandstone, and shale. Physical properties measured were unit weight and permeability to methane gas. The data show that rapid setting shotcrete has the potential for improved coal mine ground control. There is no clear evidence that either wet or dry process shotcrete is superior to the other; however, indications are that regulated set cement is preferred to cement containing fast-setting admixtures.

Jan 1, 1973

By J. Leinart

As is readily apparent, the reliability of the early-stage costs estimated for any mining project are critical to the viability of that project. An estimate too high might leave a potentially profitable deposit undeveloped or worse yet, available to a competitor. One too low might waste investment dollars in a project not yet economically ripe. There are two aspects critical to any estimate: 1. The cost data used to represent the values of the wages, salaries, supplies, and equipment. 2. The design used to determine the engineering parameters upon which the above estimated values are based. Given that all of the information contained in Mining Cost Service is provided by suppliers, equipment manufacturers and mine operators, one wonders why there is any question as to the reliability of cost estimates developed using this information. Given that it is all actual (as opposed to statistically derived) data, where do the problems with estimate reliability lie and what is the impact of the data on that reliability? The following presents a series of analyses designed to assess the reliability of the cost estimating process. Both the actual cost data and the engineering parameters upon which they are based are examined in an attempt to quantify and understand the importance of each. While several sources of cost information are available (Means, Richardson, Primedia?s Equipment Watch, and individual suppliers and manufacturers), the following rely solely on data contained in InfoMine USA, Inc?s, Mining Cost Service and in its Sherpa Mine Cost Estimating Software.

Feb 27, 2013

By J. C. Reid

Pre-cambrian scheelite deposits in Northeastern Brazil are widespread in a high grade metamorphic terrain. Previously these deposits had been interpreted as contact-metasomatic. In this paper, a volcanigenic model is invoked based on the volcanic setting (proximal to distal) and the absence of associated felsic intrusives and spatially associated metasomatic skarns. The tungsten was introduced into sediments by volcanic- exhalative processes and subsequently remobilized and further concentrated by heat and metamorphis fluids associated with high-grade metamorphism and migmitization. An alternative syngenetic - diagenetic model is discussed which requires the transport of tungsten by heteropoly acids and deposition of the tungsten as a function of Eh and Ph conditions and different clastic depositional environments. While such stratabound tungsten deposits are considered rare in North America, the hypotheses developed in this paper may open new areas for exploration.

Jan 1, 1983

By S. J. Schatzel

In order to better understand the effects of longwall mining on the methane reservoir overlying the panel, the National Institute for Occupational Safety and Health/Pittsburgh Research Laboratory (NIOSH/PRL) designed and implemented a vertical borehole monitoring experiment (BME) on an active longwall panel. The mine operates in the Pittsburgh Coalbed in Greene County, Pennsylvania. The BME site was located away from either end of the panel to avoid mechanical influences caused by the draping of overburden in this region and was positioned at the same distance from the tailgate gateroad as the mine?s gob gas venthole sites. The borehole drilling depths and monitoring intervals were chosen to address a different stratigraphic zone in each of the three planned holes. The monitoring boreholes were positioned perpendicular to face advance using a close spacing pattern of about 15 m (50 ft) between collars. Boreholes were instrumented downhole and on the surface for various measurements. It was observed from the field data that the gob gas venthole fracture network formed 24-46 m (80-150 ft) ahead of the mining face. Overburden permeability?s within the same test zones increased 100 to 500 times following undermining. The borehole test interval within the fractured rock responded to overburden gas pressure while the test interval in the caved zone responded to mine ventilation conditions. Eight months after the boreholes were undermined, slug testing indicated permeabilities had increased further in the fractured rock zone. Measurements of surface movement indicate that the permeability development observed in the boreholes is a product of vertical subsidence without lateral movement within the tensional rock mechanics zone on a supercritical longwall panel. Results from this study suggest that maximum permeability in the longwall panel overburden is achieved 58 to 190 m (190 to 620 ft) behind the longwall following maximum compaction of the overburden.

Jan 1, 2009

By W. O. Kerr

As in other industries, companies engaged in mining and extraction use and develop intellectual property (?IP?) in the form of new technologies or production processes. The development of IP assets in mining may occur as a byproduct of ongoing operations, or result from investment in dedicated R&D efforts. New technology may lower costs, increase quality of output, and/or increase operational efficiency or safety. Key business questions with respect to any new technology are how best to use IP assets, how to protect them and how to derive value from them. IP assets can provide a competitive advantage to a developing firm that uses the technology to improve its operating results. The developing firm can preclude others from using the technology if it believes that is the best way to exploit the technology?s value. Or, it can be shared with others taking care to ensure rights are maintained, thereby generating royalty income or strategic value through cross licensing or other business relationships. Either way, in order to fully realize the maximum economic benefit, innovators must protect the IP assets and control their dissemination.

Jan 1, 2012

By S. Sinha, S. Ganguly

"In an opencast mine explosives are used for fragmentation of rock. Inefficient use of explosive energy in an opencast operation produces excessive ground vibration, which is measured by peak particle velocity (PPV). To mitigate ground vibration, it is essential to develop a model to predict PPV. At present empirical models are used. These models are based on only a few input variables, hence they fail to take into account the effects of the myriad factors that cause ground vibration. Due to lack of explicit knowledge about the complex mine blasting system the scope of application of mathematical and statistical modeling techniques is limited. The artificial neural network (ANN) technique is a learning algorithm that can remove some of these limitations and can be applied to predict PPV. In this paper an ANN model is developed for prediction of blast vibration using 248 data records collected from three coal mines with diverse geomining conditions. The correlation coefficient between measured PPV and model output was found to be 0.96 and the average error percentage 11.85. The ANN model output was compared with the output of three empirical models that are widely used for prediction of PPV. The correlation coefficient between the PPV predicted by an empirical model and measured PPV data was 0.63 and the relative error percentage 38.47. This result demonstrates the superiority of the ANN model compared to empirical blast models. By using site-specific structural discontinuities as input the model performance can be further improved. Sensitivity analysis and 3D plotting were used to gain further knowledge about blast-induced ground vibration. IntroductionIn an opencast coal mine explosives are used for fragmentation of coal and overburden. If the explosive energy is not fully utilized it causes blast-induced ground vibration, which may damage nearby structures. Ground vibration is expressed as peak particle velocity (PPV). During different stages of mine planning and operation, it is necessary to use a ground vibration prediction model for blasthole design. Selection of the modelling technique is crucial. Mathematical and statistical modelling techniques have limited application because of the lack of explicit knowledge about the complex mine blasting system. Vogiatzi (2002) highlighted the problem of multicollinearity in case of statistical modeling techniques. Mutalib et al. (2013) stated that mathematical models are unable to capture the nonlinear relationship between several blasting-related parameters due to the complexity of the model input data. However, the difficulty involved in modelling complex blast vibration problems can be removed by adopting an alternative soft computing modelling approach. One of the soft computing techniques is the artificial neural network (ANN). Ragam and Nimaje (2018) developed an ANN model for predicting PPV using six input variables. Kosti et al. (2013) stated that the conventional predictors fail to provide acceptable prediction accuracy. They showed that a neural network model with four mine blast parameters as input could make significantly more accurate on-site predictions. Sayadi et al., (2013), using a database from Teheran Cement Company limestone mines, found that a neural network resulted in maximum accuracy and minimum error. Khandelwal and Singh (2009) developed an ANN model using 150 data records from an Indian coal mine with site-specific rock characteristics and geomining setting. Khandewal and Singh (2007) built a ground vibration prediction model for a magnesite mine using four prediction variables with 20 data records. Kamali and Ataei (2010) predicted PPV in the structure of the Karoun III power plant and dam using an ANN. El Hafiz et al. (2010) evaluated ground vibration predictors using data from a single-station seismograph at a limestone quarry in Egypt."

Feb 1, 2019

By D Laurence, L Ge

This paper demonstrates use of remotely sensed imagery in promoting sustainable mining. Remote sensing technology can be used during all phases of a mining project û from evaluating the resource, to making extraction more cost-effective, through to monitoring, mine closure and remediation. Use of the new generation of satellite platforms with the capability of acquiring satellite data with higher spectral and spatial resolution have the capability to emerge as essential indicator for sustainable development in the minerals industry. A life cycle approach to satellite imagery is discussed. The use of an imagery of the site prior to mining activity establishes the environmental baseline, guides mitigation measures and eventual help in suggesting remediation. Remote imagery provides the cost-effective means of monitoring reclamation, including the growth of planted vegetation, of the mine site and surrounding area. The latest advancements in satellite remote sensing are highlighted to meet the newer challenges of sustainable mining practices. Some of the worldwide successful remote sensing applications for the measurement and evaluation of the sustainable development impact of mining operations are described. Presently available source of imagery and its comparative advantages and disadvantages are provided as a guide. Finally, the limitations of this tool are indicated.

Jan 1, 2009

By K. Sugawara, H. -S. Jeong, Y. Ishiguro, J. Otani, Y. Obara, A. Hirata

A series of measurements of induced stress by the Compact Conical-ended Borehole Overcoring (CCBO) technique was performed within rock mass around a tunnel excavated in a region that an underground powerhouse is constructed under high initial rock stress. In the measurements, a phenomenon of core disking was observed during overcoring. The selecting method of strain data uninfluenced by the core disking was proposed, using X-ray CT scanner. Then, the state of induced stress determined from the selected strain data was discussed, comparing with the state of initial stress. Eine Serie von Messungen von induzierter Belastung mit kompaktem konisch-beendetem Überbohrverfahren (CCBO) wurde in Felsmassen um einen Tunnel ausgeführt, der in einer Region gebohrt wurde wo ein unterirdisches Kraftwert unter hoher anfänglicher Felsbelastung gebaut wird. Bei den Messungen wurde beim Überbohrverfahren ein Phänomen des Core Disking beobachtet. Die gewählte Methode der Belastungsdaten, unbeeinflusst durch Core Disking wurde vorgeschlagen, unter Verwendung von Röntgen-CT-Scanner. Dann wurde der Zustand der induzierten Belastung aus den gewählten Belastungsdaten diskutiert, unter Vergleich mit der ursprünglichen Belastung. Une série de mesures de contrainte induite effectuée avec la technique de forage de sur-carottage compacte à embout conique a été exécutée dans la masse rocheuse autour d&apos;un tunnel excavé dans une région de construction d&apos;une centrale électrique souterraine sous haute contrainte de roche initiale. Au cours des mesures, un phénomène de discage de carotte a été observé pendant le sur-carottage. La méthode de sélection des données de contrainte non influencée par le discage de carotte a été proposée, en utilisant un scanneur de tomographie calculée aux rayons X. Il s&apos;ensuit que l&apos;état de contrainte induite provoquée et déterminé à partir des données de la contrainte sélectionnées a été traitée, en effectuant une comparaison avec l&apos;état de contrainte initiale.

Jan 1, 2003