Search Documents

A wide-ranging base of jig data was collected from various types of commercial jigs in 9 coal preparation plants in China, and a complete data analysis was made. It was found that the sharpness ofseparation was very variable, which demonstrates the complex interplay of the many factors which influence jig performance. Tests showed that there exist optimum frequency ranges in each compartment of a jig. Stepwise regression analysis indicated that the sharpness of separation is most sensitive to the intake fraction ofthe air cycle, the frequency, and the feed rate. By means of non-linear curve fitting techniques and statistical analysis, several mathematical models were developed to describe both partition curve and the jig performance, for simulation purposes.

Jan 1, 1986

By Hewitt Wilson

Until recent years the term "whiting" was applied exclusively to the water-ground chalks of certain north European countries. In many industries these are still considered superior to the whiting made from domestic limestone and marble. However, the latter material has replaced much of the European whiting in the American market, largely due to improvements in grinding and classification by American manufacturers.4 To encourage the domestic industry, the Bureau of Mines in 1931 undertook a study of the preparation of whiting from American raw materials and a comparison of the finished products with European whitings.

Jan 1, 1937

By B. Das

Hematite floatability from two low grade banded iron ores of India, namely banded hematite quartzite (BHQ) and banded hematite jasper (BHJ) using fatty acids and amine as the collectors is investigated under identical physico-chemical conditions. The results indicated that hematite present in BHQ ore is easy to float using both the collectors, compared to BHJ ore. The difference of flotability between the two banded iron ores is that quartz grains are coarser and well liberated below 100 micron size in case of BHQ compared to BHJ ore. In case of BHJ ore, fine hematite and quartz grains are intimately inter-grown and are dispersed in thick jasper bands leading to liberation problems. Besides that, dusty jasper particles coat over hematite surface in case of BHJ ore during the process of grinding, which hinders specific adsorption of collector on hematite or quartz surfaces. This is substantiated by scanning electron microscopy (SEM). The flotation studies have indicated that it is possible to achieve ~64% Fe with ~67% recovery from a BHQ ore using both anionic and cationic collectors from a feed containing around 38% Fe. In contrast, the hematite recovery in BHJ ore was poor. Differences in the ore characteristics that affect the flotability of hematite present in both the ores are compared. Keywords: Banded hematite quartzite, banded hematite jasper, flotation, oleic acid, dodecylamine, QEMSCAN, Scanning electron microscope

Feb 27, 2013

By J. G. Haymes

This report by the Bureau of Mines is the first of two proposed papers on evaluation of spectrophotometric, spectrographic, polarographic, and other analytical methods for quantitatively determining impurities in high-purity tungsten. Some of the methods described are standard methods that have been successfully applied to determine low-level impurities, several are modifications of known methods, and some procedures are entirely original. The Bureau of Mines is actively engaged in tungsten research because tungsten has an extremely high melting point, in fact the highest of any known metal. The metallurgist must know the content of impurities in tungsten because of the marked effects even micro amounts of impurity elements have on its physical properties. The Bureau procured a number of analyzed samples of above-average purity from research laboratories of companies engaged in production and fabrication of tungsten. These samples were investigated by the analytical procedures of those companies for several metallic impurities. Subsequent analytical laboratory determination of impurities in these samples agreed with the analyses as reported. With this assurance that analytical methods were basically accurate for metallic impurities, procedures for the determination of several of these elements were modified to lower the limits of detection and increase the sensitivity of methods. Carbon and the gases hydrogen, nitrogen, and oxygen were determined by standard instrumental methods, modified to provide greater sensitivity for reliable determinations when content of these elements was low. After the reliability of the modified procedures was affirmed, they were used as a product evaluation guide in the development of a vapor-plating technique for the production of high-purity tungsten. The following list of elements can be determined by one or more of these methods: AI, B, Be, Ca, Co, Cr, Cu, Fe, Mg, Mn, Mo, Ni, Pb, S1, Sn, Ti, V, and Zn. In addition, a vacuum-fusion method for the determination of H, N, and 0, and a conductometric method for carbon are described. Lower limits of determination and detection for each element listed are given.

Jan 1, 1962

By François G. Bernardeau

Cement-bentonite (C-B) slurry walls have been used for ground water cutoff in deep excavations, contamination containment, and other applications. Hydraulic conductivity is of great concern for cement-bentonite slurry walls. The quality control program usually specifies permeability and strength tests to be performed in a laboratory on samples cast in the field and cured for a certain time. Currently there is no widely accepted in-situ test method for the performance of the constructed slurry wall. A recently constructed cement-bentonite slurry wall in South Carolina included a 200-foot-long test section done in advance of the production of an 8,300 foot-long wall. Intensive tests and investigation were conducted during and after the test section construction: Monitoring piezometers were installed using wet insertion method and packer tests were conducted in boreholes drilled in the post-28-day-cure slurry wall. The permeability measured from the packer tests was about two orders of magnitude higher than the design and the laboratory test values. Additional investigation was performed using a video camera to inspect the borehole walls especially the packer test sections. Test pits were excavated to observe both sides of the cement-bentonite slurry wall. A thorough inspection was conducted to evaluate the integrity of the wall. The lessons learned and issues regarding the disturbance effects of in-situ testing of cement bentonite slurry walls is presented and discussed.

Jan 1, 2008

By BUREAU OF MINES

This report is submitted in accordance with provisions of the Synthetic Liquid Fuels Act of April 5, 1944 (30 U. S. C. 321-325, as amended), which require that: "The Secretary of the Interior shall render to Congress on or before the first day of January of each year a report on all operations under this Act." Owing to the broad scope of the content and the diversity of interests represented, the Annual Report for 1954 has been divided into two separate publications. Each is being published by the Bureau of Mines as a Report of Investigations, and the respective titles follow: R. I. 5118, Part I - R. I. 5119, Part II - 011 From Coal. 011 From 011 Shale. The introduction, identical in both reports, summarizes research progress in 1954 under the entire Synthetic Liquid Fuels program. A free copy of either publication may be obtained by writing to the Bureau of Mines, Publications Distribution Sec- tion, 4800 Forbes Street, Pittsburgh 13, Pa. The R. I. number and title of the publication desired should be indicated.

Mar 1, 1955

Gas-liquid contacting in the packed bed is a common operation in metallurgical reactors. Research has shown that, unlike wetting flow, non-wetting liquid flows in the form of discrete droplets or rivulets. Thus, modeling of the liquid phase as a continuum is in contradiction to the observations. Also, for the non-wetting case, continuum models have failed to describe liquid flow path when the liquid source is a point source. The aim of the current work is to put forward a combined Lagrangian-Eulerian approach to model the liquid and gas flow in the packed bed. Liquid is assumed discrete and modeled using a force balance approach. Gas is assumed to be interpenetrating continua and modeled using k-emodel for turbulent flow. Structured packing is assumed and x- ray imaging technique is used to visualize liquid flow lines in the bed. Simulation results for liquid flow path compared with the experiments.

Jan 1, 2006

By Otto L. Schumacher

The Overthrust Belt in portions of Montana, Idaho, Utah, and Wyoming, an area that has contributed generously to the Nation's mineral supply, is one of the few remaining oil and gas frontiers on the North American continent. Determination of the oil and gas potential and development of mineral resources of the area have been affected by a variety of land withdrawals and other restrictions, The purpose of this study is to determine the extent of these withdrawals and restrictions and to discuss the mineral resource potential within the study area. Statistics in this report refer to land status on January 1, 1979. At that time, of the 27.3 million acres of Federal mineral lands within the study area, applications tor Federal oil and gas leases for more than 4,4 million acres (about 16 percent) were pending; the average length of time was 2 years. Federal oil and gas leases covering 8.8 million acres were also on record. Although drilling has occurred on some of these leases, others are subject to restrictions that discourage or prevent development. Some in fact contain stipulations disallowing any development.

Jan 1, 1981

By Will Jansen

When Enron rocked the United States with its Titanic-sized financial accounting scandal, miners and metallurgists were probably too busy on the mine sites in remote locations to wonder about its ripple effect. But then Enron sank, Arthur Andersen tanked and the list of scandals, costing billions of dollars, continued to ripple. Followed by the Public Company Accounting Reform and Investor Protection Act of 2002 (Sarbanes-Oxley), the recent credit crunch and weak economy, the currents from Enron?s collapse eventually washed right into the mine and the mill. These events placed intense scrutiny on metals production accounting processes as traditional semi-qualitative metal accounting practices provided insufficient credibility and transparency. ?There is growing intolerance of organizations that are unsure about the location of thousands of tonnes of ore, which will typically lose 10 to 15% of their notional value on the way to the concentrator,? Rob Morrison wrote in the opening chapter to An Introduction to Metal Accounting and Balancing. ?If the measurement and forecasts also contain qualitative (fudge) factors, a very real suspicion might emerge about just how much metal might disappear (by theft or misplacement) before detection becomes likely.? Metallurgical accounting, put simply, is the tracking and reporting of the quantity and quality (tonnage and grade, usually) of materials entering or leaving each stage from source to product for a specified accounting period. Lacking an accounting standard, metals accounting in precious metal operations has been performed in an ad-hoc, informal manner, leading to numerous errors and unidentified potentially significant inefficiencies and financial losses. As a result, mining companies are beginning to examine the quality of their metals accounting systems since they form the basis of mining company?s financial accounts and reports. As part of an effort to create that accounting standard in the mineral industry, University of Queensland?s Julius Kruttschnitt Mineral Research Centre published the textbook An Introduction to Metal Accounting and Balancing in 2009. While development of a textbook and standard are significant steps forward, the challenge in the precious metals industry is in the application of some of these suggested practices. Though improving process transparency and precious metals accounting reporting accuracy is a key driver for change from the financial side, perhaps even more important is the potential benefit to operational performance that comes with better measurement, accounting and reconciliation systems. Loss of precious metals, processing of waste and inefficient mining and processing systems are all problems that are faced in an operation on a daily basis that can help be resolved through improvements in metal accounting and reconciliation. The financial consequences of such operational inefficiencies and bad decisions based on poor information are arguably greater than consequences of fraudulent accounting. Large discrepancies between mine and mill measurement systems that measure the quantity and quality of valuable material currently exist. Some of these are expected because of statistical variation, but inherent random measurement variation is sometimes an insufficient explanation. Though the mill can usually make much better production estimates through their measurement systems (that is, less variation), this knowledge rarely benefits the mine. 3 Moreover, even if the mine does a reasonably good job of estimating expected production at the grade control level (in situ), issues such as blast movement, poor mining practice and inefficient ore/waste classification make for a disconnect between the in situ estimates of the mine and the estimates from the concentrator. This inhibits effective evaluation of the reserve and grade control models using concentrator estimates. Linking the two ends, mining and concentration, is a neglected area sorely in need of an overhaul. Hence the need for improved mine to mill reconciliation ? the area of comparing, balancing and adjusting production estimates between mine and mill for consistency in reporting.

Jan 1, 2009

By S. E. Phillipson, P. L. Tyrna

Lineament analysis, a remote sensing application for geological structures, has been criticized for reliance on subjective interpretations. The Mine Safety & Health Administration’s Roof Control Division performs lineament analyses with a technique that removes much subjectivity. Study areas are viewed on satellite images with software that allows examination under artificial sun azimuths and elevations. Extraneous lineaments are removed through successive steps of superposition, resulting in selection of the most robust linear features. Field investigations revealed a strong coincidence of joint and fault zones that were parallel with projected lineaments. The Roof Control Division’s successful identification of lineaments associated with roof falls and highwall failures has prompted some mine managers to incorporate lineament analysis as a mine-planning tool. The identification of potentially hazardous ground conditions will allow mine operators to obviate safety concerns that might otherwise adversely affect miner health and safety.

Jan 1, 2002

By G. R. Hopkins

"Refiners are generally considered solely as fuel producers, but actually they also comprise a group one of the largest consumers of fuel. For example, during the year 1929 the refineries-burned 51,544,000 barrels of oil as fuel, or the equivalent of over 5 per cent of the crude oil processed in that year. In addition enough other fuels - coal, natural gas, refinery or still gas, and petroleum coke - were utilized to raise the total fuel consumption based on B. t. u. equivalent to more than 10 per cent of the heat value in the total crude oil run to stills. Refineries utilize fuel chiefly as the heat-forming element distillation, but also under-boilers in the formation of steam used in refining, for the heating of buildings, and in the generation of electricity.In the early days of refining, the problem of fuel utilization and fuel economy was of scant importance to the refiners. Margins of profit were comparatively high and the major portion of the operatros1 attention was directed toward increasing their throughput. However, the keen competition that has prevailed in the refining industry over the past five years or more has taught the refiners that their expenses, one of the largest items of which is the cost of fuel, must be curtailed. Thus in 1925 the refiners used an average of 829,000 B. t. u. to refine a barrel of crude oil, wheras by 1929 this average had been reduced to 639,000 B. t. u., a decline of 23 per cent (see fig. 1)Since 1925 oil has ranked first as a refinery fuel (see fig. 2). The use of natural gas increased during 1926 and 1927 but declined in 1928 and 1929. On the other hand, the use of refinery gas has grown rapidly in importance. Coal has shown a steady decline in use at refineries since 1925. Petroleum coke has never supplied more than a very small fraction of the total fuel requirements, although there has been a steady increase in its use."

Sep 1, 1930

National Energy Technology Laboratory ?Only DOE national lab dedicated to fossil energy -Fossil fuels provide 85% of U.S. energy supply ?One lab, five locations, one management structure ?1,200 Federal and support-contractor employees ?Research spans fundamental science to technology demonstrations

Jan 1, 2006

By James D. Noll, Jon A. Hummer, Shawn E. Vanderslice, Aleksandar D. Bugarski, George H. Jr. Schnakenberg, Steven E. Mischler, Larry D. Patts

The National Institute for Occupational Safety and Health designed and conducted a study in an underground metal mine to assess the effects of selected diesel emissions control technologies on the concentrations of diesel particulate matter and gases in underground mine air. The control technologies studied included diesel particulate filter (DPF) systems, filtration system with disposable filter elements, diesel oxidation catalytic converter, and biodiesel blends. Each technology was tested on a mining vehicle operated in an isolated area of an underground mine supplied with fresh air. These isolated zone tests allowed for the operation of vehicles under conditions and over duty cycles that closely mimic actual duty cycles of production equipment. The DPF systems reduced the elemental carbon (EC) concentrations in mine air between 88% and 99%. The same systems reduced total particulate matter (TPM) concentrations in mine air by approximately 75%. The biodiesel blends B20 and B50 caused a reduction in the EC concentrations of 26% and 48%, respectively. Those blends also reduced TPM concentrations by 9% and 24%, respectively. The use of #1 diesel fuel reduced EC concentration by 13% compared to #2 diesel fuel. An increase in nitrogen dioxide concentration of up to two times was seen when platinum-catalyzed DPF systems were tested.

Jan 5, 2006

Flotation Circuit Optimisation - Towards More Sustainable Practice

Sep 13, 2010

By N. S. Petersen

As part of the Demand Evaluation Program of the Bureau of Mines to determine future needs for minerals, a study was instituted to develop and describe a methodology for approaching the problem of substitution between mineral commodities and between mineral commodities and other materials. The report comprises three sections: A review of general factors relative to substitution, a case study of the effect of substitution on zinc die-casting markets in recent years, and a general methodology for reviewing materials substitution with specific emphasis derived from reviewing substitution in the domestic zinc die-casting markets.

Jan 1, 1971

By David Preece

The Thirlmere aqueduct was constructed over 110 years ago to provide water from the Lake District (in the north-west of England) to the city of Manchester some 60 miles (100 km) away. The aqueduct remains, to this day, a key piece of infrastructure in the distribution of raw water in the north-west of England. A short section of the aqueduct was identified as being in poor condition during routine inspections by the owner. Subsequent investigations attributed the conduit damage to the movement of unstable ground over the conduit. Bachy Soletanche Ltd was subsequently appointed to carry out the design and construction of the slope stabilisation works and to undertake repairs inside the damaged conduit. The works were undertaken on an existing slope which, in places stands at a gradient of up to 40º to the horizontal. Strict limitations on plant and equipment were imposed by the client (United Utilities) to ensure that slope and conduit loading and associated vibrations were kept to an absolute minimum during construction. An intensive instrumentation system was installed to monitor surface movements, ground movements at depth, conduit movement and strains across existing planes of weaknesses within the conduit. The solution comprised the installation of spaced piles up-slope and down-slope of the conduit. Restrictions were imposed on the minimum stand-off distance between the outside face of the conduit and the piling works so targeted permeation grouting was undertaken to improve the ?connection? between the conduit and the down-slope piles. The presence of existing sub conduit groundwater flows was suspected and the permeation grouting was focused in areas to minimize disruption to the groundwater regime. The paper presents the basis of the design and highlights the combined construction and instrumentation methods adopted to minimise damage to this valuable asset.

Jan 1, 2011

As the surface reserves are being depleted, more and more stone operators are seeking underground mining options. Stability of underground openings is a major concern for the safety and productivity. This paper relates to a field study conducted at a large underground limestone mine in Central Pennsylvania. Identification of hazards leading to ground failures and assessment of roof fall risks are important in mitigating injuries. Field observations at this mine were integrated with Roof Fall Risk Index (RFRI) mapping software recently developed by West Virginia University. The system is designed to combine field study data related to geologic factors, mining-induced damages, roof profile, and ground water influx to generate RFRI maps. The mine has adopted a proactive ground control program consisting of comprehensive examination of drilling and bolting logs; precision surveying of roof and rib; accurate mapping of cutters, falls, and geologic structures; and installation of extensometers and microseismic monitoring systems. Investment of time and resources has eliminated fatalities and lost-time injuries due to ground fall. This paper presents the geologic settings, mining conditions, ground control issues along with risk management and control techniques adopted at the study mine.

Jan 1, 2009

By John D. Watson

The results of extensive field tests of a new and powerful method of hard rock excavation are presented in this report.* The method, known by the acronym REAM (Rapid Excavation and Mining), employs high velocity, smooth bore cannons to efficiently deliver energy to the rock and has been demonstrated for underground tunneling, drilling, surface benching, scaling, and secondary breakage in hard granitic rock at the Hope Valley Mine test site in California. Solid projectiles made from inexpensive materials such as concrete or steel, and weighing from 8 to 12 pounds, are launched by conventional high speed cannons and impact the rock at velocities of 5000 feet per second--an impact energy of about 4 million foot pounds (Figure 1). The energy applied at peak pressures of nearly 2 million psi over a period of tens of microseconds breaks down the rock by a complex mechanism of crushing, spalling, and initiation and propagation of fractures produced by the interaction of successive impacts and free surfaces. The main objective of the tests during 1973 was a demonstration of controllability of the underground operation of a silenced cannon. To accomplish this objective a 90-mm cannon

Jan 1, 1974

By Jr. Gabler

The U.S. Bureau of Mines (USBM) has developed a computerized commodity flow model for strategic and critical materials This flow model is generic and applicable to most commodities and amenable to updating supply, demand, and/or production data change. The original model, with slight modifications, was used to track the flow of chromium. This report follows the flow of chromium through its metallurgical, chemical, and refractory applications, and highlights areas where significant losses occur because of downgrading, export, or disposal. The study indicates that materials containing 451,769 mt of chromium were consumed, including 99,221 mt of chromium from recycling, Chromium losses from all causes in 1989 were estimated to be 345,347 mt from a variety of areas. These areas and their chromium losses are as follows: processing losses, 38,825 mt; processing-downgraded scrap, 18,227 mt; manufacturing losses, 18,128 mt; manufacturing-downgraded scrap, 56,595 mt; prompt scrap exported, 1,531 mt; obsolete scrap exported, 43,443 mt; recovery losses, 155,529 mt; and recycling losses, 13,069 mt. Recycled chromium-containing material accounted for 22 pct of the apparent consumption of chromium in 1989.

Jan 1, 1994

Prier to the date of this contract, Ocean Energy had developed and demonstrated a high efficiency fluorescent caplamp which operated from a standard 4 volt miner's caplamp battery. This unit produced about five times the light output of the standard incandescent miner's caplamp. The Company believed that the major market for this unique caplamp was in the industrial and municipal applications. Because of the additional safety requirements for coal mining use, and in conjunction with the much smaller market in the mining industry, the additional expense and difficulty of modifying this caplamp to comply with the Federal and State coal mine regulations were not considered at that time. Recognizing the potential of this lamp for improving illumination conditions for underground coal mining, the US Bureau of Mines contracted with Ocean Energy to make the required modifications to this lamp to bring it into compliance with the Federal and State of Pennsylvania regulations, and thereby, make this lamp available to the anthracite and bituminous coal mining industry. At the outset of the contract, the injection molds for the caplamp housing were being completed, and only prototype, hand fabricated, units were available for tests. The Bureau evaluated these prototype units and formulated a performance specification for the miner's version. Light level and distribution, weight, size, angle of tilt, and operating duration were all specified. In addition, it was required that the caplamp be com¬patible with existin charging equipment at the mines and that the final design be in full compliance with MESA Schedule 6D and he ultimately approved by MESA, Approval and Testing, as well as by the Pennsylvania Bureau of Deep Mine Safety. The scope of this contract covered the modifications required to achieve these objectives. It was agreed by the Bureau that all rights to the lamp, including design, material combinations, circuitry, etc. would remain with Ocean Energy. The charger/adapter system and components, which were developed under contract funds, are disclosed hero and become public knowledge and property. Patent applications have been filed by Ocean Energy to protect the mechanical and electrical design aspects of the lamp. It should be noted that this report contains details, designs and data which may be covered by one or more Ocean Energy patent applications, and disclosure herein is made only to provide better understanding of the contract results.

Jan 1, 1975