Search Documents

By Richard S. Dennis

Acid recovery employs ion exchange (I-X) resin as separation media for inorganic acids from dissolved metallic salts by physical adsorption and without the use of chemicals. This technology has been used for years on spent etching and plating liquors to recover acid for reuse in the bath and to reduce waste acid neutralization costs. It is also used for electrolyte treatment to facilitate valuable metal recovery via acidity reduction. TETRA's ccrxr'" I-X contactor has been used successfully for acid separation from its metallic salt counterpart in a simple, continuous operating mode using strong base anion resins. Efficient separation is enhanced by acid reconcentration to nearly its original strength or as high as 14-20%. Continuous treatment also recovers heat to the tankhouse or bath and improves metal quality due to consistent acid quality. Conventional fixed bed ion exchange (I-X) systems are impractical for acid recovery because of complex control design and large resin inventories needed to process very low liquid-to-resin treatment ratios associated with strong acid concentrations.

Jan 1, 1996

By Ram Avtar

High tensile thick plates (>80mm, weight ~3000 Kg) of medium carbon low alloy steel, when heat treated, manifested higher percentage of crystalline area (>20%) in fractured surface. Such problem was not encountered in thinner plates. The genesis of higher crystallinity in fracture was examined. It was observed that the thicker plate undergone slower rate (Average 0.9oC/Sec.) from soaking temperature to Ms temperature) of cooling after austenising during oil quenching and thereby quenched microstructure had upper bainites. During tempering of as quenched bainite, additional precipitation took place at the lath boundaries of bainite. This led to weakening of grain boundaries and aided easy crack propagation during fracture and resulted in formation of higher percentage of crystalline area in fractured surface. Enhancement in cooling rate (Average 1.8oC/Sec. from soaking temperature to Ms temperature) of austenised plate by switching over from oil quenching to water quenching practice resulted in complete transformation of austenite into martensite and produced ductile fracture (zero Crystallinity). Plates conformed improvement in mechanical properties between 2-5%.

Jan 1, 2009

By Varadajan Seshadri

Keywords: torpedo car, kinetics, physical modeling A 1:6 torpedo car physical model was built to assess the optimum refining conditions for pig iron desulfurization in the torpedo car considering the industrial parameters used in the steel plant CSBM (Companhia Siderurgica Belgo-Mineira, João Monlevade, MG, Brazil). The refining practice in this plant is through injection of a CaO-CaF2-Mg powder in the pig iron melt. Similarity between the model and prototype were established through Froude and turbulent Reynolds criteria. Mixing times were evaluated by pulse tracer addition and the kinetics of metal/slag interactions were assessed from experiments investigating iodine transfer from kerosene to water. The influence of parameters such as level of metal, gas flow rate, lance penetration, lance orientation were also evaluated.

Jan 1, 2005

By F. H. A. Abdalla

A process is described for the recovery of valuable nonferrous metals from steelmaking dust by suiphatizing roasting using ammonium sulphate. Maximum recoveries of soluble metal sulphates achieved at optimum conditions were> 99.0 %. Selective metal separation of the soluble sulphates in the leached liquors were performed either by controlling the roasting temperature or by adjustment the pH values of the leached liquor ranging from 3.6-6.2. Either pure zinc oxide orland tin oxide could be obtained at optimum conditions, and the products were evaluated chemically and by X-ray analyses. The residues rich in iron oxide can be removed and recycled. The mechanism of sulphatizing roasting process was considered. A general flow-sheet for the overall process of treatment the steel making dust to recover its valuable nonferrous metals was suggested, which ca be applied for other nonferrous bearing materials.

Jan 1, 1996

By R. Altman

A Brookfield viscometer fitted with a stainless steel bob was used to measure the viscosity of industrial lead blast furnace slags between 1126 and 1298°c. Slag oxidation state was characterized by first annealing the? slag samples at 750°c in sealed copper tubes in order to precipitate magnetite crystals. The magnetite concentration was then measured on an Outokumpu Saturated Magnetic Analyzer. Using an Arrhenius-type equation, a viscosity model was developed by regression. The equation below accounted for 75% of the variability in the data used to generate the regression coefficients and, on average, could predict viscosity within ± 12% of the measured value. The greatest difficulty encountered in measuring viscosity was due to the occasional presence of solids in the slag which caused, at times, erroneously high viscosity measurements. Precautions to minimize this problem are outlined in the text.

Jan 1, 1985

By S. Djaroudib

Keywords: iron recovery, hematite, hydrolysis, polyvinylpyridine The precipitation of hematite (Fe2O3) from ferric chloride media at ambient pressure and at temperatures below 100°C was studied as part of a program to recover a marketable iron product form metallurgical processing streams and effluents. Hematite was formed in preference to ferric oxyhydroxides (e.g. ß-FeO?OH) by controlling the precipitation conditions, especially by adding Fe2O3 seeds. The extent of the hydrolysis reaction was found to depend primarily on temperature and on the free-acid concentration. As to the latter, the controlled addition of an adsorbent of free acid, in our case the anionic resin polyvinylpyridine (PVP), was shown to allow for the nearly complete removal of iron as readily filterable Fe2O3. The hematite product typically contains = 63% Fe and = 1.5% Cl, and its composition does not change appreciably upon repeated cycling using regenerated PVP.

Jan 1, 2005

By Yoichi Takeda

Copper solubility in Si02-CaO-FeOx slag equilibrated with copper matte in 10% S02 atmosphere at 1573K was estimated. Essential parameters are activity coefficients of copper oxide and sulfide, oxygen and sulfur potentials and activity of copper in the slag-matte system. A large number of experiments provide proper parameters to calculate copper solubility in slag. A classical thermodynamic model postulating CUOO.5 and CuSo.; molecules assists in estimating copper solubility in slag. Additions of Si02 and CaO reduce copper solubility almost in any condition. Copper loss, that is function copper solubility and slag volume, in the silica saturated Si02-FeOx binary slag is minimally equilibrated with less than 66% copper matte while copper loss in the 50% FeOx-SiOrCaO ternary slag saturated with 2CaOSi02 is minimally equilibrated with over 66% copper matte. This slag composition has potential for continuous copper converting, direct copper production or high-grade matte production.

Jan 1, 2003

By Alessandro Navarra, Joël P. T. Kapusta

"The converting cost modeling software introduced by Ng et al. in 2005 [1] has been extended to consider the reprocessing of reverts and copper scrap. The original model evaluated the operational costs of a Peirce-Smith converter; algebraic relationships had been implemented with arrays (to represent matrices, vectors and scalar ratios). The new software brings flexibility to the underlying thermochemical balances, by using linked-lists instead of arrays. It is now possible to consider the blending of several feeds, including reverts and scrap.The software computes the length of the converting cycle from the Fe and S content of the charge together with the blowing rate; the times required for other operations (charging, skimming and idle time) are also accounted for. The costs of consumables such as flux, fuel, oxygen or compressed air are all evaluated. Downtime, labor, and materials for converter lining repairs are also considered. The software is easily extended to examine the costs of alternative operating strategies or injection technologies such as sonic single pipe injection and sonic shrouded injection. The potential cost benefits of alternative operating procedures and technologies are discussed through example calculations."

Jan 1, 2009

By Jeffrey D. Winterton

Keywords: Copper, ion exchange, sulfonic acid, bis-picolylamine, ion exchange modeling, ion exchange kinetics As part of an investigation into the feasibility of using ion exchange resins to recover copper from aqueous waste streams generated during the manufacturing of semiconductor devices, the uptake of copper onto two ion exchange resins was investigated. The resins studied were DOWEX G-26, a standard gel type sulfonic acid resin, and DOWEX M4195, a macroporous chelating resin with a bis-picolylamine functional group. The equilibrium and kinetic behavior of the uptake of copper were investigated over a range of copper concentrations with constant sulfate concentration and different levels of acidity. The homogeneous structure of the G-26 resin yields equilibrium relationships that fit the Langmuir equation, and equilibration times of less than 30 minutes. The uptake behavior of M4195 is complicated by the need to absorb co-ions to maintain electroneutrality, resulting in uptake profiles that change character with increasing copper concentrations, and extended equilibration times.

Jan 1, 2005

By H. K. Fouad, L. A. Guirguis

The starting mill strip solution· for this study· is an ammonium uranyl tricarbonate solution of pH 8.2 containing 20g uranium/liter, after a DEPA/TOPO extraction process from sulfuric acid leaching liquor. To the first portion of the concentrated acidified strip solution, hydrofuoric acid is added at 95°C in reduced condition to obtain uranium tetrafluoride. The second portion of the uranyl carbonate strip is subjected to a precipitation step by admixing 0.3 volume of non-solvent precipitating agent such as acetone per volume of uranium. ·Uranium oxide (U30 8) is obtained from this precipitate by calcination for half an hour at 800°C in air. The third portion of the strip solution is neutralized to a pH 6.5 with sulfuric acid to precipitate iron and other contaminants. The solution is further acidified to a pH 1.85 with continuous air bubbling to remove CO2, followed by H2Ch precipitation at pH 3.5 to obtain uranyl peroxide. The latter is reduced by stannous chloride to obtain uranium trioxide dihydrate UO3. 2H20. Identifications, characterization· and purity of these products are carried out by complete chemical analyses, Scanning electron microscope study, tap density determination, X-ray diffraction and infrared spectroscopic investigations. The achieved results agreed well with that of the published data for these nuclear grade purity products.

Jan 1, 2000

The cleaning of copper containing fayalite slag using a CuFe alloy was studied under an oxygen pressure ranging from 10-7 to 5 X 10-11 atm at 1200º c. The reduction of copper from fayalite slags by Cu-Fe alloys was found to be very effective. For example, at a P 02 of 10-7 atm, the copper content in the slag was reduced from 4.1 to 0.402 wt. percent after 90 min. of reaction time using a Cu- 5.27 wt. percent Fe alloy. The copper reduction rates were found to be independent of P02 in the gas phase when using Cu-Fe alloys which exhibit an iron activity of greater than 0.4. A mechanism for slag c1eaning is proposed based on the concept that the Cu-Fe alloy lowers the oxygen potential of the slag according to Eq.1 1, fol1owed by the reduction of cuprous oxide by wustite as shown in Eq.2. Here X represents element X in the alloy phase while (X) represents the element in the slag phase. The copper and iron transfer behaviour obtained in this study are explained by a ?Stepwise equilibrium model.

Jan 1, 1985

By Fuxing Yin, Akira Sato, Yoshiaki Ohsawa, Kohji Kawaharai

"INCRAMUTE alloy (nominally 45Mn-53Cu-2Al wt. %) has a specific damping capacity as high as 0.4, through a solid-solution and aging treatment. The damping behavior of the alloy is highly temperature-dependent and shows a peak near room temperature. The inadequate strength in the high damping condition restrains the practical application of the alloy, as structural components. Ferromagnetic MnB particles are dispersed in the alloy during induction remelting the matrix alloy in an argon atmosphere. Surface modification of the MnB particles by mechanical alloying (MA) and suitable control of the addition process cause a homogeneous distribution of MnB particles in the alloy. In the composite containing 2 wt. % MnB particles, temperature dependence of damping capacity is improved, and higher damping capacity is still retained in the temperatures over 60 °C. Meanwhile, the Young's modulus and tensile strength were also increased by about 20%. The roles of the MnB particles in improving both damping behavior and mechanical properties were also discussed.IntroductionMany viscoelastic materials, such as rubbers, polymers and plastics, have the superior ability to damp vibration and noise. However, in the applications as structural materials the high damping capacities of materials are pursued upon the satisfactory mechanical properties, especially those at elevated temperatures. Damping alloys are finding more and more applications in structures where noise and vibration ·should be ·eliminated. Specific damping capacity (SDC), defined as the ratio of the energy dissipated to the maximum vibration energy stored per cycle, is usually used to evaluate the damping capacity of alloys. INCRAMUTE damping alloy, developed by the International Copper Research Association, Inc., has a nominal composition of 45Mn-53Cu-2Al in weight percent. The high damping· microstructure of this alloy is obtained through the solution treatment at 820 °C followed by a water quench and aging at 400°C for 10 hours followed by cooling to room temperature [1]. With the heat treatment, a SDC peak ·vs. temperature of as high as 0.4 was observed in the alloy at the strain amplitude of about 10-3 while a tensile strength of about 500MPa was sustained."

Jan 1, 2000

By Timo Kankaanpää

Keywords: Solvent extraction, dispersion, phase separation, CFD The liquid-liquid dispersion phases are separated by gravity in a solvent extraction settler. This separation step is made more effective by picket fences. The picket fence geometry and its physical placement have a significant effect on the separation process, because the purpose of a fence is to smoothen and control organic-aqueous dispersion flow in the first part of the settler and achieve a deep and dense dispersion layer in the front end of the settler resulting in a clean phase separation. In this study, physical phenomena in the solvent extraction process and phase separation in a solvent extraction settler with and without picket fences have been examined using a commercial CFX software package. It can be concluded that the used CFD-approach proved to be a complementary tool for optimizing and designing the solvent extraction settler.

Jan 1, 2005

By Regina Maria Pinheiro

This work has for objectives to characterize a waste generated in the form of sludge during the treatment of the effluent of a paper making industry and to evaluate the effect of its incorporation in the amount of 10 wt.% on the properties and microstructure of a clayey body used for brick production. For the characterization of the waste the following techniques were used: X-ray diffraction, X-ray fluorescence, differential thermal analysis and termogravimetric analysis. Incorporated bricks were produced in industrial scale before firing at 750°C in a Modified Caieira type furnace. The physical and mechanical properties evaluated were water absorption and compression strength. The microstructure of the fired ceramic was evaluated by optical microscopy. The environmental evaluation was made by solution test and atmospheric emission by monitoring the release of SO2, NOx and particulate material. The results showed that, in agreement with the characteristics of the waste, its recycling into red ceramic can contribute to decrease the consumption of fuel during the firing stage. The properties of the fired ceramic attend the norms. With respect to the environmental aspect, the incorporation of the waste did not impact the environment.

Jan 1, 2009

By Chen Song

Keywords: Co3O4, Cobalt Compounds, Morphology, Urea, Homogeneous Precipitation Depending on experimental condition, precipitation from cobalt nitrate and chloride solution in the presence of urea yield dispersed cobalt compounds with different chemical compositions and morphologies. The effects of concentration of cobalt solution and urea, agitation, on precipitation morphology were investigated experimentally. Generally in closed systems the particles are identified as cobalt (II) basic carbonate with needle type shape. In open system, spherical and plate-like precipitations of cobalt (II) basic cyanate are formed. The chemical formula of cobalt compounds was confirmed. They are CoII,III(OH)0.83(CO3)0.49 Ay?0.14 H2O (in tightly-capped reactor: A stands for NO3?, Cl?; y[A]molecular weight < 12.9) and CoII,III(OH)0.83(NCO)XAy?0.14 H2O. (in open reactor A stands for: NO3?, Cl?; 42 x + y[A]molecular weight < 44.82). The main reason was that the primary particles had different chemical compositions for the effects of the different kinds of anions and stoichio-chemical compositions of the primary particles. The effect degree of the anions depended on the co-existing anion radius in the reaction solution. According DTA-TG analysis of the cobalt compounds, the latter particles transform to Co3O4 powders on calcining. The shape of the Co3O4 particle with porous character has inheritance with precipitation. In this paper, it concludes that the particle formed by the principle of nucleation-aggregation in aqueous solution. The process of aggregation has played an important role in formation of particles. During calcination, the aggregation would be destroyed partly.

Jan 1, 2005

By He De-wen

The municipal solid waste is a by-product of the daily life of urban residents. The quantity and ingredients of municipal solid waste has exceeded the current management and disposal ability, which has done a great harm to municipal environment and sanitation quality and threatened people?s health. On the basic of analysis on the amounts and main elements of municipal solid waste of Changsha City, the sanitation landfill, incineration, composting, reclamation and utilization technology of household waste were compared specifically in this paper. Based on the concrete conditions of Changsha City, the paper has proposed a disposal proposal combined with reclamation and landfill of municipal solid waste of Changsha City, and the environmental benefit, social benefit and economical benefit of the prepared processing routes were also analyzed in the paper.

Jan 1, 2009

By Nicolas Reynier

The separation of radionuclide during rare earth element (REE) production is an important requirement for developing the Canadian REE mining industry. Separation of actinides from REE is often a large concern in the rare earth industry because of the need to manage the radioactive nuclides. A patented process developed for actinides extraction from radioactive wastes was applied to REE ore. Objectives were to optimize the process for REE leaching from ore, and separate radioactive impurities from sulphuric and nitric liquor by ion exchange (IX). Ore leaching was optimized using a surface response plan to ensure statistical significance. In optimized conditions, solubilization yields ranged from 90–95% for Th, 60–75% for U, 48–55% for LREE, and 59–75% for HREE in sulphuric and nitric media. Both media were compared for radionuclide removal from rich REE-bearing mineral liquor by IX. Actinides separation ranged from 92–97% for Th and 69–96% for U in sulphuric and nitric media.

By Preben Ingerslev

Control of the reheating of ingots is based either on surface temperature measurements using optical pyrometers or on furnace set points and reheat time determined empirically. This paper presents a real-time mathematical heat flow model, named BESTT, which calculates the temperature distribution in an ingot cross section when reheated or cooled. The model runs on a 486 PC in less than one minute for a variety of ingot cross sectional shapes such as circular, square and with some considerations octagonal and heavy-cornered square. Initial temperatures can either be uniform or nonuniform while accounting for temperature dependent thermophysical properties. The model was developed and verified using 718 alloy ingots in box type furnaces. When integrated with on-line pyrometric measurements, BESTT can provide for improved feed back in the reheating control loop. The use of BESlT will assist in reducing energy costs, and improving product quality and consistency. EPD Congress 1994 Edited by C. Warren The Minerals, Metals k Materials Sodety, 1993

Jan 1, 1994

By Adam Powell, Salvador Barriga, Matthew Earlam

"The inert anode is a key enabling technology for dramatic energy and emissions reduction in extractive metallurgy. In molten salts, the materials challenge is nearly insurmountable: the anode must conduct electrons at high temperature in a pure oxygen and molten salt environment. A solid electrolyte, e.g. zirconia, between the salt and anode removes the molten salt stability constraint, and can act as a container for a liquid metal anode. This can be liquid silver for oxygen-generating inert anodes, or several metals for natural gas-fueled anodes; it is possible to switch between these modes. The solid electrolyte brings several other benefits: it eliminates molten salt contamination of the anode gas, creates a reducing environment enabling low-cost steel vessels, increases current efficiency, and eliminates carbon contamination of the product. New developments presented here, including current collector and low-cost anode designs, amplify these benefits for producing aluminum, magnesium, rare-earths, and other metals.IntroductionReactive metals such as magnesium, aluminum and rare-earths play increasing roles in efficient transportation and clean energy. In response to new fuel economy standards, automotive OEMs are planning large increases in use of aluminum and magnesium to reduce vehicle weight. Rareearth permanent magnet motors and generators exhibit better power-to-weight and efficiency than induction motors and other designs, making this today's primary motor technology for hybrid and electric vehicles, and for wind turbines. Nickel metal hydride (NiMH) batteries with lanthanum are dominant in hybrids. In 2011, transportation comprised 28.6 out of 103.1 EJ of US energy consumption [1] and 1,845 out of 5,471 million metric tonnes (MMT = 109 kg) CO2e of US greenhouse gas (GHG) emissions [1], creating big targets for economy-wide reductions.Unfortunately processes for making reactive metals for these applications are very inefficient and heavily-polluting. In primary aluminum production, Hall-Heroult cell electricity use [2] is more than double the reaction enthalpy due to heat losses through frozen cryolite side-walls and anode gases, graphite anode plants add significant energy use and GHG emissions [2] (see Table 1). Magnesium is even worse: silicothermic reduction by the Pidgeon process in China produces about 85% of the world's magnesium using coal or coke gas [3]. Chloride electrolysis begins with high-purity MgO and requires carbochlorination or hydrochlorination and costly chloride dehydration [4]—rendered unnecessary for aluminum by the Hall-Heroult cell. Production of neodymium and lanthanum with graphite anodes leads to inconsistent carbon content: small cells make 1 kg batches for analysis, sorting and sale by carbon content, with very high labor and analysis costs. And vertical electrodes give no incentive to reduce anode effect: some reports indicate that China's rare-earth metal industry emits more CF4 and C2F6—with global warming potential (GWP) 6500 and 9200 times CO2 respectively—than China's aluminum industry [5]."

Jan 1, 2014

By Yunnen Chen

This work concerns the removal of zinc(II) and COD by means of sawdust obtained as a by-product from locally used wood. The zinc(II) and COD removal study has been carried out batchwise where the influence of physico-chemical key parameters such as tree species, pH value of solution, temperature and contacting time and dosage of adsorbent have been considered. The maximum percent removal was attained at pH 9 all for Zn(II) and COD after about 60 min. The adsorbent can be effectively desorption using 0.1 M HCl. The experimental results showed that ion exchange maybe the major adsorption mechanisms for binding the divalent metal ions to the sawdust. Sawdust was a potential adsorbent for the removal of Zn(II) from the effluent of electroplating industry.

Jan 1, 2009