Search Documents

By Kot F. Unrug

Since the introduction of longwall systems, the prediction of roof behavior and support requirements have become the major issue referring directly to safety as well as productivity. In more recent times, and especially in the USA where longwalls are exclusively equipped with costly hydraulic self- propelled support systems, a decision whether a longwall is applicable in a given condition, and when so, what kind of equipment should be selected, is of primary importance. There are numerous examples where lack of experience, and subsequently wrong selection of supports or winning machines, resulted in considerable losses. It should be emphasized that careful studies of prevailing geological and mining conditions, especially in a new area, are required to assure a successful operation. An evaluation of the conditions can be carried out in different ways utilizing such methods as: - Theoretical approach. applicable when geological conditions comply with the theoretical assumptions. - Empirical relationship which gives satisfactory results where the coefficients could be adequately determined. - Structural geological studies which must be undertaken in all cases, since the frequency of fractures and their orientation have a prevailing influence on roof behavior. - Scale model study on equivalent material for determination of failure conditions in the roof and mechanism of movement (flow) of broken rock matter. Coefficients for empirical formulas can be determined by these types of studies, as can boundary limits for mathematical modeling. - Mathematical modeling, e.g., finite element analysis. - Measurements and observations taken underground during the development period end utilization of experience for previous longwall panels in the area. Usually it is the most practical method where mining and geological conditions are comparable. An application of me or more of the above approaches remains to be a matter of judgement for particular conditions, however, the utilization of a practical experience, when available, is usually the safest way for planning a successful longwall operation.

Jan 1, 1982

By Jesse L. Craft

Field investigation of surface subsidence events associated with both active and abandoned underground coal mines in the United States has established criteria that enable the prediction and classification of mine-related subsidence. The key was establishing the role of geology in all types of subsidence and the recognition of beam subsidence in specific geologic settings. The classification is based on overburden thickness, variations in stratigraphy, topography and mine plan. Types of subsidence are Pit, Room, Sag, and Beam. Pit subsidence is associated with three geologic settings: shale overburden, seasonally wet unconsolidated overburden, and perched water table in unconsolidated overburden. Room subsidence occurs where the roof across the width of the room fails to the surface and a shallow depression develops. Sag subsidence develops where the pillars are failing in conjunction with roof failure. Overburden thickness is generally greater than 150 feet. Beam subsidence can occur in all terrains. It is associated with retreat mining and room and pillar mining where pillar crushing or pillar compression has taken place and barriers are left inplace. They occur as beam arch or one-sided beam subsidence. Beam arch failure occurs where mining has taken place on both sides of a coal barrier. One-sided beam failure is associated with retreat mining moving from a barrier towards the entry in hilly topography. This type of subsidence occurs where a hard, thick, rock unit is acting as a bridge supporting the overburden and outcrops on the hill side.

Jan 1, 1992

By William G. Pariseau, Michael K. McCarter

"The challenge of estimating mine-wide subsidence and linkages to seismicity over tabular deposits is addressed by a special finite element technique (dual node - dual mesh). Subsidence and mine-induced seismicity begins near the face when caving occurs and propagates to the surface as extraction reaches a critical extent. Thus, the challenge is to obtain details at the face at the meter scale and also at the surface over the whole mine at the kilometer scale. Interactions between old and new sections of a mine are automatically taken into account with this technique. The finite element method is well established technology based on fundamentals of physical laws, kinematics and material laws. With this technique, no empirical ""scaling"" or fitting computer output by input data ""adjustment"" to mine measurements is necessary. Capability is demonstrated for doing practical whole-mine subsidence analysis from first principles. Mine-induced seismicity is shown to correlate well with face advance and element failure.INTRODUCTIONSeismicity associated with coal mining has been under study for several years by a team at the University of Utah. Team members include mining faculty, research geophysicists and students from the Departments of Mining Engineering and Geology & Geophysics. Mines in central Utah that have been studied include the Trail Mountain Mine (Pariseau, 2015; Pariseau and McCarter, 2015), the Beehive Mine, also known as the Des-BeeDove (Pariseau, 2014), and the Crandall Canyon Mine (Pariseau, 2015). These mines were developed from outcrops in the Wasatch Plateau coal field west of Price, Utah, where the topography is characterized by . steeply incised canyon drainages and high plateaus with relief of a thousand meters or so.Seismicity associated with coal mining in central Utah has been of interest for many years and includes studies in the Book Cliffs to the east of Price, Utah, where mining is still active (Smith et al, 1974; Agapito, Goodrich and Moon, 1997; Arabasz et al, 2001; Arabasz et al, 2002; Fletcher and McGarr, 2005; McGarr and Fletcher 2005; Maleki, 2005) and to the northwest (Ellenberger et al, 2001). Results of many micro-seismic studies are summarized perhaps best by lannacchione, et al (2005) in stating, ""Deviations from normal strata response can provide useful stability information.""This study concerns a fourth underground coal mine in the southern portion of the Wasatch Plateau coalfield, hereafter referred to as the MINE. Focus is on mining from 2004-2008 with the objective of examining mining in relation to seismicity."

Jan 1, 2016

By Tom Barczak

Early in my career, while giving a presentation on shield design for longwall mining at one of the International Conferences on Ground Control in Mining, the late Jim Scott told me that I was finally getting it, because ?I was starting to think like a rock!? Although I didn?t realize it at the time, those few words changed my career forever. At the start of my career, I did a lot of laboratory testing, taking advantage of the unique capabilities of the Mine Roof Simulator to study the performance and design characteristics of longwall shields. I had a pretty good handle on what made shields work and what made them fail, but I was still struggling with how and why they develop their in-service loads and what they were actually controlling as opposed to being passive bystanders in a world beyond their control. It became clear to me that the simplistic models of dead weight loading could not explain the behavior I saw and measured underground. The problem did not go away when I started studying standing support systems. Again, I learned much about the strength, stiffness, and stability of these supports and helped the industry develop several new support products that attempted to provide more efficient support designs. But here, too, the simplistic models of dead weight loading did not seem to fit for me. That?s when I began to incorporate the ground reaction concept as a way of integrating the support response and the ground behavior into a cohesive design methodology. The concept has its limitations, no doubt, but I believe some form of it will be the future of not only designing supports but also, in the broader sense, enhancing the engineering aspects of ground control. The paper presented at the International Conference on Ground Control last year by Esterhuizen (2010) on pillar behavior is evidence of this. Think like a rock. Jim Scott was right. It takes two to dance. You can?t dance alone and you will never understand ground control by thinking like a support! ?Dumb as a box of rocks?? I don?t think so. The answer lies in the rocks!

Jan 1, 2011

By Behdeen Oraee

Constructing tunnels underground is generally described as a high-risk activity because conditions in the surrounding area tend to be unpredictable. This would and can create unique dangers in every situation. It is important to gain a deep understanding of the risks associated with tunneling in order to reduce the likelihood of their occurrence and severity of their consequences should they occur. For this to be achieved, different risks should first be evaluated and ranked according to their relative importance and criticality. The Amir Kabir tunnel is considered one of the most dangerous tunnels in Tehran, Iran, in terms of the risks involved in its excavation and their potential consequences. In particular, part T4 of the tunnel passes through a zone of different strata and also a compound of various soils. This paper studies part T4 of the Amir Kabir tunnel from a risk analysis and risk management point of view. In doing so, factors increasing total cost, causing delay in the project completion time, decreasing the operation rate and downgrading project quality were identified and ranked according to their importance using the aggregate primary index risk method. For this purpose, a comprehensive questionnaire was designed and completed by tunneling experts. By responding to the questionnaires, the experts determined the relative likelihood of occurrence of the studied factors and their potential consequences. As a result, the experts suggested several alternatives to reduce the risks involved in this particular study. Moreover, the experts completed new questionnaires whilst taking into account different alternatives. In the next step, the risks before and after applying the alternatives were compared. As a result of performing the said analyses, it was concluded first that the aggregate primary index risk is an effective tool in identifying the risks involved in such projects. Second, it was concluded that, by taking into account different alternatives when analyzing and ranking the risks, severity of the said risks can potentially be reduced. Also, by considering such matters when analyzing tunneling risks, the projects? efficiency can greatly increase as a result of reducing risks that threaten financial and human resources. The approach introduced in this paper, together with the methodology described, can be adopted by the mining design engineer in all similar situations. They will be of particular advantage in such methods as room and pillar mining, where the number of similar tunnels required is high.

Jan 1, 2014

By Gennaro G. Marino

As part of the development of a shopping center in West Virginia, a significant bench had to be cut into a mountainside that was over 700 ft. high. As a result, a steeply stepped, over 400-ft.- high wall was created. The high wall exposed old abandoned room-and-pillar coal workings at the toe of the cut. Because of exposure to the elements, the mine openings began to severely deteriorate with significant potential of undermining of the rock cut face and causing a large rock fall(s). Exacerbating this wall problem was a set of fairly planar sub-parallel and sub-vertical joints creating, in essence, thin rock slabs. Also present were stress relief fractures that were observed in the exposed pillars. Given the proximity of the project building to this high rock face, mitigation of the rock fall potential was deemed necessary. In order to prevent continued damage and deterioration of these exposed mine entries, the rubblized openings were filled with bulkhead grout and pressure injected with grout. The total amount of grout installed in these openings was about 3,945 CY. Also, a rock drape was attached to the entire face to mitigate small rock falls from natural causes. There also existed another level of mining below the ground surface and under an existing building at a depth of about 160 ft. Under a portion of the building, the pillars in these old works were second mined, and the building seemed to have been already affected by limited subsidence above this area. Also, calculated pillar safety factors in this high extraction section of the mine were too low. Consequently, these old works were stabilized by saturation grouting. An indication of overall roof distress was the significant fracturing encountered in the bedrock overburden during the drilling of the injection holes and the volume of grout placed in these holes. The total grout installed in the high extraction section of the lower mine was about 6,660 CY. This paper describes the investigation and the grouting techniques employed at the rock cut face and under the existing building to mitigate continued damage to avoid future subsidence problems at the face and the building premises.

Jan 1, 2013

By Andrew Lewis, Amarit Nitaramorn, Alexander Garcia, Peter Altounyan

"Indonesia is a major coal producer, the vast majority being sourced from opencast operations. Underground production to date has been constrained by unfavorable ground conditions and limited local experience. However, an underground trial in East Kalimantan has now shown that it is possible to successfully extract coal and mine safely, despite the technical challenges.A trial drift mine has been worked to a current maximum depth of 160 m (525 ft) in a dipping coal seam. The 3 m (10 ft) thick coal seam is overlain by very weak mudstone and sandstones. The mudstone forming the immediate seam roof strata proved a particular challenge given its adverse reaction to water and overall friability.Rock bolts were used as roadway support, the system being carefully selected to optimize effectiveness. An innovative method of partial extraction was trialed, which demonstrated the potential for productive mining despite the ground conditions. Roof falls have occurred within the working area, and roadways demonstrate reasonable stability over time.Throughout the course of the trial, strata behavior monitoring has been an important aspect, and a comprehensive ground control monitoring system is in place. This has enhanced the ability to increase the level of support where required and to react to deteriorating conditions. In addition, monitoring information has allowed a quantitative assessment to be made of the technical feasibility of future full-scale mining.INTRODUCTIONWith current production at over 200 million tons, much of this destined for overseas markets, Indonesia is the second largest exporter of coal (Ritschel and Schiffer, 2007). The majority of the coal is sourced from the Kalimantan coalfields. Mining is predominately opencast, yet in recent years there have been attempts made to introduce underground operations. This move would permit continued access to good quality seams that are beyond the reach of viable opencast mining."

Jan 1, 2010

By Ted Klemetti, Gabriel Esterhuizen, John L. Ellenberger

"Advanced numerical models can be used to evaluate entry support systems in coal mines. However, these methods require specialized software and specialized skills to create the models and evaluate the results. Practicing support design engineers require a method to rapidly assess a proposed support system for a given geotechnical scenario. A prediction equation that can be used to assess roof support systems has been developed from the results of hundreds of FLAC3D analyses that were conducted during recent research. These models were validated against field cases and empirical design approaches and were found to adequately predict entry stability in coal mines. The understanding developed from the model outcomes was used to develop an equation to predict entry roof stability against large roof falls. Least-squares error analysis was conducted to find appropriate parameters for the nonlinear equation. The developed equation can be solved using spreadsheet software, allowing for rapid assessment of alternative support system performance in variable geological conditions. The performance of the prediction equation is evaluated against empirical design methods and against selected case histories of support practices at currently operating mines. Examples are presented that demonstrate the performance of the equation in variable geological settings. The stability factor (SF) prediction equation can be used as an assessment tool to assist in the design of coal mine roof support systems.IntroductionGround falls represent a significant proportion of injuries and fatalities in underground coal mines in the US. During 2013, ground falls were responsible for 4 of the 14 fatalities and 16.6 % of the 1,577 reportable lost-time injuries (MSHA, 2015). In addition, each year about 400 to 500 large roof falls are reported that can extend up to or above the bolted horizon. Large roof falls and associated ground fall hazards can be mitigated through improved support design.The research presented here particularly addresses the problem of large roof falls that extend more than 90 cm (3 ft) above the roof line of an entry and may extend above the bolted horizon. Smaller roof falls that fall out between supports or extend less than 90 cm (3 ft) above the roof line are excluded. These smaller roof falls can be controlled by appropriate surface support such as roof screen or other skin control methods. Also excluded are roof falls that are associated with an individual geological structure such as a slip of fault. Structure-related instabilities can be controlled by strategically locating individual roof bolts or other supports appropriate for the local situation."

Jan 1, 2015

By Mark K. Larson, Douglas R. Tesarik, Heather E. Lawson

"Load transfer distance (LTD) is simple in concept and usually evident in underground coal mines. Many people in the mining industry recognize LTD as the distance from the panel to where the mine ribs and pillars show evidence of renewed spalling, floor heave, or other effects of increased weight due to longwall mining or pillaring. Barrier pillars, in particular, are designed to shield mains and other relatively permanent facilities from this loading. LTD is also important in determining the extent and degree to which mining increases the load on pillars and ribs in the gate roads. Generally, a long LTD reduces loads in gate roads, but may require larger barrier pillar widths to protect mains or adjacent panels from excessive loads. Therefore, a long LTD may make it easy or difficult to meet various objectives of mine layout design . LTD reflects overburden geology in two ways: First, overburden that is weak and readily caves will limit both the amount and distance of load transfer. Second, stronger, stiffer, sandier, and more massive overburden increases both the amount and distance of load transfer. As such, LTD is central to coal mine layout design and calibration of numerical models that seek to anticipate these transfers of load during mining. However, the term does not have a consistent definition in the literature, and various instruments and observational techniques with varying sensitivities and thresholds have been used to indicate the onset of mining-induced stress increase and, subsequently, to determine an LTD. Consistency is important for meaningful comparison of ground response between mining sites and for accurate calibration of models.This paper adds to the body of observed and reported LTDs by presenting cases with relatively sandy and massive overburden at two western coal mines. These two cases include observation and measurement of LTD with multiple methods and provide insight into how distances reported relative to different criteria and instrumentation could be adjusted for comparison against a common base. This base is the criteria used by Peng and Chiang (1984) to determine their empirical equation. In one of these two cases, LTD was recently measured at a western U.S. coal mine (Mine A) to be approximately four times that calculated using the Peng and Chiang empirical equation. LTD measurements were examined using various instruments at Mine A and at adjacent Mine B. The measurements at Mine B showed that LTD was significantly greater than that calculated by the Peng and Chiang equation. Difficulties with BPC installation and fittings at Mine B permitted only ranges of LTD to be determined from some BPCs. Even so, the LTDs and ranges of LTDs determined were consistent with the LTDs determined at Mine A."

Jan 1, 2015

By Mark K. Larson

Panel-scale modeling of stress changes induced by longwall coal mining is a challenging problem, particularly in deep mines of the western United States. Two common approaches to this problem are the empirical and boundary element modeling methods. One boundary element method, LaModel, was recently calibrated to field measurements at a mine in Colorado (Larson and Whyatt, 2012). However, the calibrated overburden properties were extreme, resulting in very low estimates of gob loading. Next, the empirical method was calibrated to field measurements and applied to the problem, but this approach clearly extrapolated this method well beyond the characteristics of underlying cases. This paper examines a third option, the elastic continuum boundary element program Mulsim. The program was expanded to handle LaModel-size meshes in a version dubbed Mulsim/ Large. Properties for the elastic, homogeneous overburden model in Mulsim were estimated as a thickness-weighted average of typical published elastic properties for each major stratum. These properties, along with a commonly used pillar strength equation and coal properties, produced the measured load transfer distance and reasonable gob loading without further calibration. Given the number of input parameters required for all of these methods, it is not surprising that LaModel and the empirical approach could be adjusted further to incorporate similar gob loads. However, these extraordinary measures failed to bring gate road pillar loading in line with Mulsim results. Differences in pillar load estimates continued to be significant (as large as 65% in this study). These results demonstrate that, for this particular case, the choice of analysis method impacts results in ways that cannot be removed by calibration of input parameters. Finally, the natural fit between the Mulsim model and mine conditions suggests that approximating overburden at the particular site used for this research as an elastic continuum is superior to the alternatives examined.

Jan 1, 2013

By Peng-Fei He

CT scanning tests were used to detect the pre-existing fracture systems of 36 cubical coal blocks. Systematic procedures were developed to construct the pre-existing fracture geometry of the cubical coal blocks from the CT images. Based on the constructed fracture systems, the fracture tensor components were calculated to capture the directional effects of the fracture system of the cubical coal blocks. The effect of the pre-existing fracture system and different combinations of confining stresses on the strength and deformability of coal masses was investigated at a preliminary level using some true triaxial test results and the computed fracture tensor components. The strength of the cubical coal blocks in the loading direction was found to be closely related to the summation of the fracture tensor components in the two perpendicular directions to the loading direction and the level of the confining stress system. The deformability of cubic coal blocks in the loading direction was found to be correlated to the fracture tensor component in the same direction.

Jan 1, 2014

By Essie Esterhuizen, John Ellenberger, Dennis Dolinar

"Underground stone mines in the United States use the room-and- pillar method of mining. The stability of the roof between pillars determines the mining dimensions and size of equipment that can be used. The findings of a survey of roof span stability issues and design practices are presented, and the observed factors contributing to roof instability are discussed. Identified stability issues are evaluated, such as maximum roof span, horizontal stress, and roof beam stability. The results of field observations, roof monitoring, and numerical analyses are used in the evaluation. The importance of the first roof beam thickness and its impact on roof stability and support requirements is presented. An evaluation of the current experience with stone mine roof spans relative to international experience is presented. A step-by-step design procedure is suggested which emphazises the need to collect adequate geotechnical data, understand the immediate roof stability, select a mining direction, and meet support requirements.INTRODUCTIONIn room-and-pillar mines, the roof between the pillars is required to remain stable during mining operations for haulage as well as access to the working areas. Roof and rib falls account for about 15% of all reportable injuries in underground stone mines (Mine Safety and Health Administration, 2009). Therefore, the stability of the roof is an important safety consideration. The size of the rooms in underground stone mines is largely dictated by the size of the mining equipment. Large mining equipment is used, requiring openings that are on average 13.5 m (44 ft) wide by approximately 7.5 m (25 ft) high to operate effectively (Esterhuizen et al., 2007). The dimensions of the roof spans are largely predetermined by the equipment requirements, and design is focused on optimizing stability under the prevailing rock conditions. If the rock mass conditions are such that the desired stable spans cannot be achieved cost effectively, it is unlikely that underground mining will proceed. In addition, large roof falls can extend across the full width of a room and may extend more than 5 m (16 ft) above the roof line. These large falls are a safety hazard and can have a significant impact on mine access and production. The National Institute for Occupational Safety and Health (NIOSH) research into stone mine roof stability has focused on identifying both the causes of roof instability and techniques to optimize stability through design."

Jan 1, 2010

By G. P. Neobutov

The near surface inclined gold ore deposit is mined out at freezing temperature. The replacement of ore pillars by artificial freezing rocks during the rock pressures control in this conditions presented no difficulties. At the present, the mining operations are maintained at a depth of more than 300 meters. The exploration of mining conditions showed partial warming of rock mass and unstable ground conditions. Analytical calculations using a mathematical model of heat exchange predicted undesirable duration of freezing of artificial pillars. Practical techniques and recommendations for mining with ice pillars as an artificial support system using a new freezing method are discussed.

Jan 1, 1996

By Bill A. Kyslinger

"In underground mining, machine design is predominantly dictated by mine conditions and individual customer desires. In partnership with Foresight Energy, J. H. Fletcher & Company was tasked to design and manufacture a new roof bolting machine with six independent drilling apparatus on board capable of drilling and bolting the roof and ribs with material handling. This is the first Fletcher® six-head machine to be designed and built for the mines in the United States. The machine is intended to work in the Illinois Coal Basin.The objective was to produce a machine capable of drilling and installing six bolts simultaneously with a limited number of operators. The goal of the mine is to decrease the time to bolt a cut to improve the safety level of the current roof bolting method, improve efficiency and to improve the bottom line cost of entry development. The customer wanted four mast feed drills at the front of the machine dedicated to installing roof bolts and then another two mast feed drills behind them dedicated to rib bolts. This dictated the requirement of latched controls, which would allow the operator to start drilling one hole and then latch the controls to be able to move on to the next. To accomplish this, we developed a unique hydraulic latch circuit to maintain operator safety and compliance. Guarding was added to prevent an operator from coming into accidental contact with a latched drill.The result of the design is a machine with a single platform and six independent masts with drillheads: four masts strictly for drilling and installing roof bolts on the front of the platform and two masts on the back of the platform for rib bolts. The feed and rotation controls at each operator's station include a latch control for drilling. The latch control will allow the operator to lock in the feed and rotation once the hole has been collared, allowing the operator to move on to the next hole. The rear of the machine is equipped with material handling. There are two material pods with winch controls as well as a mesh rack that includes mesh lift, mesh tilt, and mesh sump.The six-head roof bolter allows fewer operators to drill and install roof and rib bolts, which in tum lowers the miners' roof exposure per cut. This design reduces the operator's exposure from the inherent pinch points and rotary hazards once he has engaged the latch drilling. Therefore, the machine will help to decrease the time to bolt a cut, improving productivity while enhancing the ability to operate the machine safely."

Jan 1, 2016

By Weijia Guo

With the exploitation of coal resources, a large area of land had been affected by surface subsidence, causing conflicts between man and land to become more conspicuous by the day, affecting the life of general public, and constraining further development of the land. This paper predicts the subsidence areas according to the 10-year mining plan of the Jibei mining district as an example. A plan of environmental management was developed based on sciences and practical economics.

Jan 1, 2006

By L. A. Sandbak, Yan Xing

"The purpose of this study is to evaluate the rock mass stability around the tunnels by three-dimensional (3-D) numerical modeling. Complex geological and tunnel features have been included in the model using the software package 3DEC™. Based on the available information on stratigraphy, geological structures, and mechanical properties of rock masses and discontinuities from the underground mine, 3-D stress analyses were performed on various cases with different K0 (lateral stress ratio) values, constitutive models, as well as support systems. Relations between these factors and the distributions of stress, displacement, and failure zones around the tunnels were obtained and discussed. Finally, comparisons between the field deformation measurements and numerical simulations are used as validations for the simulations, helping to determine the appropriate K0 value and material constitutive models for the underground mine.INTRODUCTIONThe case study site is an underground mine in the USA with a monthly ore production between 20,000 and 30,000 tons. The regional geology of the mine is structurally and stratigraphically complex. Rocks in the area include carbonaceous mudstone and limestone, tuffaceous mudstone and limestone, polylithic megaclastic debris flows, fine-grained debris flows and basalts, all part of the Cambrian-Ordovician Comus formation and related dikes. Both the mineralization and faults have general orientations striking N-S to NW-SE with high dip angles. The ore body in the mine has an incline of about 25---45 degrees located in relatively low quality rock; hence, cut-and-fill mining has been used.This underground mine has two vertical shafts used for ventilation, ore hoisting, and for personnel and material transportation. Development drifts were designed and driven to extract and transport the ore, as shown in Figure I. Bolts, mesh, and shotcrete have been applied in this mine for ground control. In order to reach various locations, the tunnel system is designed with different heading directions and inclines, which will be described in detail later. The area selected for modeling is a cubic region including all the tunnels inside the black square (Figure 1)."

Jan 1, 2016

By Srisharan Shreedharan, Gang Huang, Hongqing Song, Sijing Cai, Pinnaduwa H. S. W. Kulatilake

"Subsidence prediction due to ore extraction and backfilling during open stoping operations for an underground iron mine in China is reported in this paper. Geologic complexities including faults and interfaces between different lithologies, and the stoping and backfilling sequence adopted from the mine plans are incorporated in building a 3-D discontinuum numerical model. The stoping was simulated in two vertically stacked horizontal layers (Fig. 6), with a total of 16 stopes. Large displacements of up to 50 cm were predicted by the model along the roof of the stopes, and a maximum surface subsidence of 22.5 cm was predicted by the model . Backfilling was found to control subsequent deformation and subsidence. The extraction of the upper orebody led to relatively higher deformations in extracting the lower orebody. Finally, the predicted subsidences at all locations along a subsidence profile on the surface are shown. INTRODUCTIONThe Luohe iron (pyrite) mine, located in Hefei city, Anhui, is an underground mine in China, being mined through the open stoping and backfilling method. The orebody lies at a depth of about 400 m and has an average thickness of 250 m (Magang Steel Company, 2012a). Discovered in the 1960s, the location has a reserve estimate of 300 million tonnes, which have been mined since 2007. The orebody has been divided by the mining company into an east and a west section to facilitate planning for ore extraction.Figure 1 shows the surface above the underground mine, which is seen to contain many human settlements including villages, pastures and other infrastructure. These locations are sensitive in that they need to be protected from potential adversities due to the underground mining, such as surface subsidence. While it may be near impossible to completely eliminate the subsidence due to ore extraction, operations such as backfilling have been adopted by the mine in an effort to substantially reduce it. Hence, this paper focuses on describing the stability of stopes in the mine and estimates future subsidence in a part of the mining region through numerical modeling."

Jan 1, 2016

By R. F. Valene

This paper is not available for inclusion in the Proceedings at the time of printing. but it will be included as an insert

Jan 1, 1984

By Arka Jyoti Das, Prabhat Kumar Mandal

"Coal mining in India has a strategic importance for the energy security of the country. Presently, the majority of coal production is coming from open-cast mining. Due to the fast depletion of reserves amenable to open-cast mining, future coal production will depend primarily on underground production. In conventional bard-and-pillar/room and pillar mining as it is practiced in India, the percentage of extraction is very low. In fact, within most Indian coalfields, a large number of coal seams extract only 15- 20% of coal, but no pillar extraction is done due to the presence of surface or sub-surface structures leading to huge amount of coal being locked-up in underground. Spontaneous heating and fire, the accumulation of poisonous gases, severe stability issues, unsafe workings and environmental hazards are all major problems associated with these developed coal pillars, so there is a pressing need for technology in the mining industry to extract this huge amount of coal locked up under different constraints. In this study, we propose that the locked-up coal be extracted by replacing the developed coal pillars with artificial pillars. The paper briefly discusses the extraction methodology designed for this and its evaluation through numerical modeling for applied suitability underground.INTRODUCTIONDriven by rising populations and urbanization, an expanding economy and also a quest for improved quality of life, energy usage in India is expected to increase manifold in the coming years. As for India's energy scenario and its projected future plans, there is no doubt that coal will remain a prime source of energy, even over the next few decades.The majority of coal production in India comes from open-cast mining because of large-scale mechanization, but the coal reserves amenable to open-cast mining are gradually depleting - which may impose adverse impacts on the energy sector if underground production does not increase. Underground coal extraction, meanwhile, is going to become more complicated in near future due to the fast exhaustion of easily mineable coal reserves."

Jan 1, 2016

By Dr. Daniel W. H. Su

t is both an honor and privilege for me to nominate Dr. Daniel W. H. Su for the inaugural Syd S. Peng Ground Control in Mining Award. I can think of no better candidate than Daniel that is deserving of this award ? an award to recognize technical excellence in advancing ground control technologies [and] approaches. Daniel?s education and career spans over three decades. Having graduated from National Cheng Kung University in Taiwan in 1972 with a B.S. degree in Mining and Petroleum Engineering, he spent the next four years in the Taiwanese military and mining industry, before moving to the United States, where he enrolled in West Virginia University?s Mining Engineering Department. He received his M.S degree in Mining Engineering from WVU in 1978; then in 1982 became the first person to ever receive a Ph.D. in Mining from WVU. His thesis was titled, ?Development of Ultrasonic Techniques for the Measurement of In Situ Stresses?.

Jan 1, 2006