Search Documents

By Eugie Kabwe

The velocity of detonation (VOD) is a significant property considered when rating an explosive. It may be quantified as a confined or unconfined velocity. The confined velocity is the rate at which the detonation wave propagates through an explosive within a blast hole or any restrained space. The unconfined velocity emanates when an explosive is detonated in the open. However, the confined velocity is more significant as explosives are usually employed under a definite degree of confinement. This paper evaluates the increment of air deck volume and its effect on the VOD. The air gap (air deck) volume is increased stepwise from 10 to 30% of the total blast hole volume by reducing the stemming height in the collar zone. Thereafter, the VOD estimation in the 172-mm-diameter explosive column is conducted using the Dáutriche technique. It is observed that the VOD reduced with the increasing air deck volume and detonation failure is high when 30% of the blast hole volume is replaced with air deck. It is deduced that the increment of the air deck volume has an effect on the attenuation of the steady-state VOD.

By R. L. Grayson

For the years 1990 and 1991, West Virginia's underground coal small-mine fatality rate « 20 employees) was approximately ten times higher than the national coal industry rate. Although the total number of fatalities decreased to 17 in 1992 (from 22 in 1991), West Virginia still led ,the nation in coal mining fatals. A team of mining and safety professionals from West Virginia University studied the problem over the past year, interfacing with the Mine Safety and Health Administration and the West Virginia Office of Miners' Health, Safety and Training. A clear path for 'formal intervention was determined and is presented here.

Jan 1, 1994

By K. Chief

American Indian lands contain a vast amount of renewable and non-renewable resources that have consequently been mined (Smith and Frehner). Therefore, it is understandable that tribes are concerned about environmental impacts from mining and their ability to minimize and mitigate these impacts. This has created a need to better understand mining and its environmental impacts. The University of Arizona Superfund Research Program Mining educational modules developed educational modules for tribal colleges focusing on environmental impacts of mining, remediation of mining wastes, and sociocultural impacts of mining. Educational modules are independently packaged units of study designed to enhance the learning process and can be modified and adapted to different learning scenarios and objectives. In addition to providing specialized knowledge, the modules feature hands-on activities, incorporation of technology, student involvement, discussion, and exchange of ideas. Modules will aim incorporate traditional ecological knowledge and approaches that promote effective science learning for native students. Modules are designed to augment existing associates of science programs (e.g. biology, chemistry) currently offered at tribal colleges and can be modified for use in K-12 education and for non-tribal audiences.

Feb 23, 2014

By C. R. DeGennaro, Yongjun Zhang, J. Bickson, J. L. Carr, Chenming Zhou, J. R. Srednicki, B. Lambie, M. Girman, J. A. Galanko

Between 2005 and 2021, surface mining haul trucks were involved in 54 fatal incidents in the United States [1]. Collision warning and avoidance systems (CXS) can help haul truck operators navigate their route safely. The evaluation of CXS object detection performance for surface mining haul trucks relies on the positional accuracy of the ground truth instrument. As part of a holistic approach, researchers from the National Institute for Occupational Safety and Health (NIOSH) characterized the accuracy of a global navigation satellite system (GNSS) that serves as the ground truth instrument to determine object position and velocity in CXS object detection performance testing. We used precision surveying equipment to establish ground truth points for comparison with GNSS data collected for static positional measurements and reduced-scale straightline vehicle dynamic tests. We conducted these tests with real-time kinematics (RTK) and then satellite-based augmentation systems (SBAS). For the dynamic tests, we measured a distance error of 1.34 m (4.40 ft) using RTK and 1.50 m (4.92 ft) using an SBAS. This research will provide CXS manufacturers and CXS researchers a basis for evaluating the positional accuracy of CXS. Note that we did not evaluate any CXS in this experiment.

Feb 1, 2024

By Pratima Meshram Abhilash

In this review, availability of germanium in primary and secondary resources and its recovery from these resources are presented. With nearly 40% germanium consumed in fiber optics and scarcity of resources, the global consumption outplays the primary production. Germanium exists as a substituted element in zinc sulfide matrix of lead–zinc sulfides and lignites. Nearly 60% of the germanium supply is met by zinc refining residues, and about 20–30% of germanium is produced from coal and its by-products. Germanium recovery from various resources such as zinc plant residues, coal and coal plant waste, spent optical fibers, and copper flue dust has been examined. Bioleaching was exploited by few researchers to extract germanium from zinc sulfides, sulfide tailings, jarosite, coal fly ash, and flue dust. This review covers the various work carried out by different chemical separation processes, viz., chemical precipitation, solvent extraction (SX), ion exchange (IX), and membrane processes, as well as biological approaches.

Jan 16, 2022

By Nikhil Dhawan, Shrey Agrawal, Ashwini Kumar

The current study investigates sericite clay as an alternative source of potash and alumina. The alumina and potash content in the sericite is approximately 35 and 10%, respectively, compared with 50–55% in bauxite ore. Muscovite and illite phases are stable, and direct leaching is found to be ineffective. Here, planetary ball milling was performed, which provided dissociation of stable phases to relatively reactive phases. The milling led to a five-fold increase in the surface area, resulting in enhanced leaching kinetics even at low acid concentration. The statistical design obtained optimal conditions of 8 h of milling followed by leaching in 1.73 M HCl at 75 °C, yielding 82% alumina extraction in precipitate with 85% purity in γ-alumina form and 63% potassium dissolution in sylvinite phase. The yield of the precipitate was ~65–68%, and the acid leach residue contained primarily silica.

By Sandeep Kumar Jeripotula, Govinda Raj Mandela, Aruna Manglapady

Dumper operators are frequently exposed to whole body vibration (WBV) in surface mines. Surface mining activities involve the amalgamation of comparatively high intensity of vibration and extended exposure durations. Efficient risk reduction mandates knowing of important phases of a task that poses a threat to health of dumper operators. So far in India very limited studies have been reported on WBV exposure with regard to surface mines. This paper evaluates WBV of dumper operators based on ISO 2631-1:1997 Standards and European Union (EU) Directive 2002 for different phases of job cycle. Six dumpers were considered for this study and the vibration measurements were made for all the four phases of the job cycle by placing the triaxial accelerometer on the operator’s seat-surface and at the seat-back, independently. The findings of the study revealed that the haulage task (loaded travel and empty travel) remains the chief contributor to vibration exposure according to seat-surface and seat-back measurements. Maximum frequency weighted root mean square (RMS) of 1.12 m/s2 and 1.09 m/s2 were reported for empty travel task for seat-surface and seat-back measurements, respectively. For seat-surface measurements based on RMS, Z axis remains as the dominant axis of vibration for all the dumpers during haulage task, whereas for seat-back measurements, the dominant axis varies between X and Y. Exposure action value (EAV) based on RMS has exceeded the threshold value of 0.5 m/s2 for all the dumpers during loaded travel and empty travel for seat-surface as well as for seat-back measurements.

By R. Brändle, R. Luis-Fonseca, R. Cornejo, G. Fischer, G. Von Rickenbach, J. Jarufe

Rock damage around underground excavations has been an important hazard in mines and tunnels. Rock dilation generates buckling that needs to be contained before it causes damage to equipment or safety concerns to mine workers. In seismically active mines, rockburst occurrence has been widely recognized as one of the most important hazards in deep mines and tunnels. While there is a wide range of cases where rockburst hazard can be mitigated through dedicated excavation sequences, reentry procedures or exclusion zones, there are still many situations where large unexpected rockbursting may occur, relying only on rock support as the last mitigation measure to prevent production and safety losses. Considering the previous situations, surface support as mesh, plays a major role containing the failed/ejected rock and providing a safe working environment to the underground operations. While there have been considerable achievements in improving mesh resistance, with more than 26Kj/m2 of energy dissipation capacity, there is still a lack of research in the overlapping mechanism and load transfer between contiguous mesh elements. This paper presents the state of the art in static and dynamic analysis of welded and rolled mesh overlaps, based on experimentation carried on by Geobrugg in their Research Center, leaving clearly established that the difference in meshes is not only in levels of energy absorption, but also concluding that in the case of high resistance rolled meshes overlapping is not necessary and the transmission of stresses can be fully guaranteed by using suitable connecting elements. All these characteristics, supported by operational advantages as light weight and mechanized mesh installation, provides a considerable improvement in safety and productivity, improving the economic value of the project

Apr 26, 2022

By William D. Cassity, Batric Pesic

Introduction Gold mining on an industrial scale is becoming increasingly dependent on low-grade refractory sulfide ores that contain large amounts of pyrite (FeS2) and arsenopyrite (FeAsS). Gold is usually present as sub-microscopic particles dispersed evenly throughout the sulfide matrix. Without some form of preoxidation, efficient recovery of this finely disseminated gold through cyanide leaching is hampered because the surface of the sulfide particle becomes passivated and impervious to penetration of the cyanide. Traditional methods for recovery of refractory gold from arsenopyrite ores include roasting and autoclave leaching. A modem alternative method is to preoxidize the mineral using the bacterium Thiobacillus ferrooxidans prior to attempting to re- cover the gold through cyanidation. The bioleaching of arsenopyrite ores presents a problem in the mobilization of large quantities of arsenic, present both in the +5 and +3 ionic states. Dissolved arsenic species pose a dual problem: they are -1 to the bioleaching process itself through inhibition of bacterial activity, and they also pose an environmental threat. The arsenate anion (AsO2) has been shown to be more toxic to living organisms, including Thiobacillus ferrooxidans, than the arsenate anion (AsO43) (Collinet and Morin, 1989). There is some disagreement as to the fate of arsenite in bioleaching solution. Mandl, Matulova, and Docekalova (1992) reported that dissolved arsenite concentration was constant during a long-term bioleaching study of chalcopyrite using Thiobacillus ferrooxidans. Torma and Oolman (1992) report that Thiobacillus ferrooxidans has been found capable of oxidizing As3+ to As5+. The solid products of arsenopyrite/pyrite bioleaching include jarosite (MFe3(SO4)2(OH)6 where M can be K+, Na+, NH4+ or H3O+), scorodite (FeAsO4.2H2O), ferric hydroxides, and ferric hydroxysufites (Carlson et. al., 1992; Van Breemen, 1982; Lazaroff et. al., 1982). The particular species formed is a function mainly of pH. Little study has been performed on the effect of solid products on bioleaching. Pesic and Kim (1993) showed that Thiobacillus ferrooridans cells served as a nucleation sites for jarosite particles, which grew rapidly and eventually killed the cell. Most bioleaching studies are performed at low pH&apos;s (<2.0) under uncontrolled conditions. By studying bioleaching of arsenopyrite under controlled pH conditions and at higher pH&apos;s (2.0 to 3.0), the distribution of iron and arsenic between the solid and liquid phases can be controlled, and their effects studied. The objective is to develop a bioleaching process that operates at high efficiency while keeping amounts of dissolved heavy metals low. Pesic, Stohok, and Torma (1993) demonstrated the usefulness of this approach in the leaching of cobaltite (CoAsS) concentrates. Materials and Methods The focus of this study was the bioleaching of arsenopyrite ore by Thiobacillus ferrooxidans. The parameters studied included the effects of pH, and the effects of arsenate (AsO43 and arsenite (AsO2). pH studies included pH set initially but not controlled, and pH controlled continuously with NaOH or LiOH. Bioleaching results from two strains of Thiobacillus ferrooxidans with different adaptation histories were compared. Bioleaching experiments were conducted in 150 ml stirred glass reactors using a strain of Thiobacillus ferrooxidans adapted to arsenopyrite ore, supplied by the U.S. Bureau of Mines. These bioreactors were innoculated with stock cells grown on arsenopyrite ore for 14-16 days. Typical elemental breakdown for this ore was: As, 9.90%; Fe, 18.60%, Stot, 9.26%; Suifide, 7.50%; SiO2, 25.90%. Mineralogically, the ore contained both arsenopyrite and pyrite. Bioleaching efficiency was measured by withdrawing bioleach solution samples at selected intervals, filtering, and measuring the amount of dissolved cobalt, iron, and arsenic by atomic absorption spectroscopy. Because the precipitation of iron and arsenic at higher pH&apos;s would lead to unreliable results, a 100 mg tracer of cobaltite concentrate from the Blackbird mine in southern Idaho was added to solution. Dissolution of the cobaltite tracer was used to indicate bioleaching of the bulk arsenopyrite ore. Cobalt has been shown to be stable in solution even when iron and arsenic were precipitated (Pesic, Storhok, and Tonna, 1993). The pa-

Jan 1, 1995

By W. G. Pariseau

Face and pillar bursts, bumps and bounces are violent failures that occur in underground coal mines in response to a complicated interplay of face and pillar geometry, seam depth, coal strength and moduli and interactions between roof, seam and floor strata. Additional complications arise from the presence of gas, mainly methane, and associated pressure and flow that vary with time and are further influenced by the rate of face advance. Numerical models provide a means of quantitatively accounting for the various complications of mining geometry, the stratigraphic column, mechanical properties, gas flow properties and associated interactions. A fully coupled hydromechanical finiteelement code, utAH4, serves the purpose well and allows study of the important interaction between stress concentration and gas pressure in determining safety and stability of the face during the advance of a longwall panel in a deep underground coal mine in central Utah. Face advance is relatively fast compared with gas flow and depressurization in coal seams of low gas permeability. Consequently, gas pressure is high at the face. When a longwall is stationary, depressurization occurs at the face, so effective stress and strength increase. thus, when gas flow at the face is high and requires a pause in face advance to bring gas concentration to an acceptable level, a second benefit occurs because of timely depressurization. However, quantitative analysis of a deep coal mine shows that regardless of gas pressure, high stress concentration is more likely to pose a threat to face and pillar wall stability.

Aug 1, 2013

By Lee R. Kump, Sarma V. Pisupati, Peter L. Rozelle, Alan R. Larson, Timothy S. White, Nicholas A. Crescenzo, Maureen D. Feineman

The Mercer Clay bed in central Pennsylvania has produced feedstocks for the refractory industry in the USA and has also been investigated as a source of alumina and lithium. Developments in global markets for these commodities, as well as rare earth elements, have led to their classification as critical minerals in the USA, in turn renewing production opportunities for the Mercer Clay resource. The work reported here includes a review of the clay types and minerals involved, as well as past mineral processing and extractive metallurgy test work, and reports new research results from renewed investigation of the deposit as a polymetallic resource. This renewed work has found lithium contents that exceed 1,000 ppm, lying directly below the overlying Mercer coal, where the alumina content ranged from 32 to 34 wt%. Total rare earth concentrations were somewhat lower than have been found elsewhere in the region, and the highest contents were also found to be stratigraphically close to the coal. Further work is required to establish the mineral hosts for lithium and rare earths and to define the extent of enriched alumina, lithium, and rare earth concentrations.

Jul 22, 2021

By J. T. Crawford

A comprehensive strategic planning model has been developed for the phosphate strip mining and chemical operations at White Springs, Florida. The computerized model covers ore body modeling, production simulation and financial analysis. Several innovative features in the model include using NPV techniques in ore body block economics, adapting the floating cone method to a floating template for generating dragline mining units automatically, using interactive graphics for designing mining units, and a dragline move economics algorithm for automatic scheduling of mining unit assignments and moves. Simulation of chemical plant production uses linear programming and concentrate inventory levels control mine operating schedules.

Jan 1, 1997

By R. W. Smith

The electrokinetic and flotation behavior of the green alga Chlorella vulgaris was studied in the absence and presence of Pb(II), Al (III) and flotation collectors. It was found that the presence of Al (III) is necessary for good flotation of the organism whether or not Pb(II) is present when dodecylammonium chloride or sodium dodecylsulfate is used as collector. Best flotation using dodecylamine is at about pH 8 and best flotation when using sodium dodecylsulfate is at about pH 4. It appears because of the small size of the organisms that the Al (III) is necessary for flocculation to enhance bubble-cell contact and C. vulgaris removal from water. When N-dodecyl-2-aminoproprionic acid is used as collector good flotation occurs at about pH 4 without the addition of Al (III).

Jan 1, 1990

By Hernan Fernandez, Khalid Saif F S Al- Khayareen, Volkan Salepciler, Jacek B. Stypulkowski

Wakrah and Wukair Drainage Tunnel, WWDT is 13 km long with a 4.5 m ID sewer water tunnel about 50 to 60 m below ground surface. Integral to the project are several adits with provisions for future connections as well as four work shafts, four intermediate access shafts, ancillary hydraulic structures, and an Odor Control Facility. The shaft depths range from 50 to 60 m. The project is constructed in aggressive ground with aggressive ground water. The construction activities require years of pumping and disposal of the ground water during tunneling operations as well as construction of permanent structures in shafts. Grouting of the corrosive rock mass in corrosive groundwater for the WWDT has been described in detail.

Jun 23, 2024

By Harold J. Schock

The cases of no auxiliary ventilation and ventilation with tubing were mathematically modeled, using a turbulent dispersion model. The scooptram that is used to load is modeled as a variable-speed, variable-strength source of pollutants moving in and out of the dead-ended drift. Model predictions are compared to experimental measurements. A parametric analysis was performed to determine the effect of exhaust pipe location and time spent out of the drift, as well as to determine if a relationship existed between CO2 and NO levels. It was concluded from this analysis that when modeling a load-haul-dump cycle, it is necessary to use a model that has the capability of predicting changes in source strength as well as source location. It was also determined that four relevant factors include effective heading height, apparent longitudinal diffusion coefficient, transverse concentration gradient at the face, and average dispersion width of the exhaust jet. As these factors change with heading geometry and ventilation configuration, they were determined experimentally, Carbon dioxide was used as a tracer to calibrate the model; since, knowing the fuel flow rate, it is possible to calculate CO2 production. The above four factors in the computer model were calculated using a regression analysis, comparing predicted local concentrations to measured local concentrations. The model was then verified after this calibration process using additional experimental results. With the calibrated model, it is possible to predict pollutant concentrations at any location in the heading using an engine map and the previously calculated flow field. A parametric analysis shows that the exhaust pipe location can have a significant impact on operator exposure to exhaust gases. It was also shown that NO concentration varies directly with C02 levels. Predictions using the dynamic model are contrasted with constant source strength (pollutant flow rate) results. An analysis of these predictions for computing time-weighted average NO shows the dynamic model predictions of operator exposure to this pollutant to be less than one-half of the value predicted using a constant source model.

Jan 1, 1981

By K. L. Boyd

"Can the ever-increasing tonnages of ore and waste being mined today be accommodated simply by using bigger and better crushers? This paper reviews the latest primary crushing and large cone crusher designs. It highlights how—in addition to using the larger crushers now available—maximizing the utilization percentages in each of the four stages of the rock size reduction circuit will assist in meeting the larger production requirements of existing and new mining operations. Its goal is to help consultants and operators select the optimal equipment and custom-designed items in the material handling flowsheet from the mine to the mill, maximizing operating hours per year. INTRODUCTION Are larger crushers the answer to meeting the demands of existing or new mining projects for increased tonnage? Boyd (2002) predicted that larger crushers for primary and fine crushing would be beneficial and contribute to the further development of mineral processing. Larger crushers for primary and fine crushing applications are now available. The rock size reduction process from the mine to the selected milling process facility has not changed since man first broke a rock to get at the interesting mineralization within. The rock size reduction process circuit from the mine to the mill can be summarized in four stages: • Stage 1: Mining (rock breakage and fragmentation) • Stage 2: Pre-screening (scalping) • Stage 3: Primary crushing • Stage 4: Fine crushing (secondary, tertiary and quaternary) Plant throughput and ore delivery schedule will form the basis for flowsheet design and equipment selection. Once the project design criteria and the mine plan have been established, the circuit’s utilization percentage (percentage of hours when the circuit is being utilized) can be optimized for each of the four stages. The mining and process departments are the key stakeholders in the selection of the final comminution circuit, and both departments should be familiar with and contribute to the design of the circuit. This paper focuses on the four stages of a rock size reduction circuit from the mine to the mill, equipment selection, various ore and waste handling flowsheets, and improvements in crusher station design, all with the purpose of maximizing availability and plant utilization percentages. What is a large tonnage? From 1907 to 1914, the American Panama Canal excavated 300 million tonnes of material in 7 years (History of the Panama Canal, Wikipedia). Today’s large mining operations can move the same material in 10 months, using large crushers or multiple crushers for ore processing and large crushers and a mixture of truck haulage and conveyors for handling the large waste tonnages. Some examples include:"

Jan 1, 2017

By Ronald B. DeDiemar

It is generally held that cone crusher application technology is strictly an art and thus subject to the vagaries of emphirical and/or trial and error judgments. While this is basically true, certain factors have been identified which, when properly defined, can significantly reduce the element of chance. This paper will bring out these factors as well as pointing out other technologies available to predict and/or analyze cone crusher performance.

Jan 1, 1977

By R. C. Gilmore

Computational fluid dynamics (CFD) has been used to model gas compositions in underground longwall coal mine gobs to study oxygen ingress and the development of potentially explosive methane-air mixtures that may form in the gob. The scenarios studied involve various headgate and tailgate ventilation and inertization schemes and controls. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at Colorado School of Mines have used an innovative meshing approach, allowing easy adaptation of the CFD model to adjust to a variety of bleeder and bleederless mining geometries, with gob porosity and permeability scalable over a wide range. This paper presents the methodology of the meshing and scaling approach along with recommendations for using CFD modeling in longwall gob ventilation applications. The new meshing technique was utilized to evaluate the function of a back return in a progressively sealed gob. The back return was successful in maintaining sufficient oxygen concentrations in the tailgate corner of the longwall face.

Feb 23, 2014

By Nick Hasenack

In the pelletizing plant of Hoogovens, Estel BV, a varying mixture of hematites and magnetites is used for the production of acid and (occasionally) fluxed pellets. Optimum results regarding productivity, quality and process control are obtained with mixtures containing 30-40 % magnetites. A decrease of the magnetite ratio or an increase of the basicity has a great influence on both productivity and heat and power consumption. Tests have been carried out to find the extent to which magnetite can be replaced by b.f. dust, mill-scale and coke breeze. Pilot plant tests show that about 80-100 % of the production loss due to a decrease in magnetite content or to the increase in basicity can be regained without damage to the quality by adding coke breeze. The amount of coke breeze should be limited tot 1,5 %; if this percen¬tage is chosen higher, the quality of the pellets deteriorates rapidly. The amount of coke breeze to be added should be about 30 % above the theoretical value, based on heat balance considerations. The results achieved by incorporating b.f. dust and mill-scale into the pelletmix were also encouraging, but as some types of mill-scale are very difficult to grind and the supply of b.f. dust is limited, the research has not been carried out extensively in this field. The pilot plant tests on replacement of magnetite by coke breeze have been followed by industrial tests, during which the breeze was added to the ore feed before the dry-grinding system.

Jan 1, 1977

By C. Bryce

Rhenium is primarily recovered as a byproduct from molybdenum roasting circuits. However, rhenium is also present in copper heap leach solutions at very low concentrations, and this represents a potential new rhenium source. Freeport-McMoRan (FCX) has developed a new process using carbon adsorption followed by ion exchange or solvent extraction to concentrate rhenium from less than 1 ppm to 15 g/L. The product is compatible as a feed to an existing rhenium processing plant. A pilot plant operated at Freeport-McMoRan?s Sierrita Mine has demonstrated the technical and financial feasibility of this new process. Copper heap leaching dissolves more than just copper from the copper ore. Several metals can be identified in leach solutions at concentrations of financial interest, rhenium in particular. Rhenium spot prices ranged from a yearly average of $1,070/kg ($483/lb) in 2005 (Magyar, 2008) to $10,400/kg ($4,706/lb) in 2008 (Polyak, 2013). The spot price in September 2013 was approximately $3,000/kg ($1,357/lb) of rhenium (Metal Bulletin, 2013). Several facilities at Freeport-McMoRan have very low rhenium concentrations in their copper leach solutions, ranging from 0.1 to 0.7 mg/L. The large quantity of solution available, if coupled with an attractive rhenium price, means that the rhenium contained in leach solutions may represent a significant value if a method of extraction could be developed. Testing has confirmed that rhenium adsorbs onto activated carbon much more selectively than other metals in the pregnant leach solution (PLS). A 100-gpm pilot plant was constructed to verify the lab-scale results on a larger basis and establish operating parameters for a full-scale operation. This report summarizes the initial technology development and pilot plant operation.