Search Documents

By Steven W. Hunt

Appropriate seals, portal ground improvement, and compatible shaft construction techniques are vital elements for launching and receiving tunnels effectively in urban areas where adjacent property requires protection from excess ground movements. This paper focuses on seals and ground improvement along with shaft wall types, required to launch or receive tunnel boring machines within wet, permeable ground at the portal zone. The paper also discusses probing to verify suitability before the tunnel eye is cut. Methods addressed include: rubber gasket seals; soft eyes; double walls; top hats for reception; and, portal zone ground improvement (permeation grouting, jet grouting, un-reinforced slurry diaphragm wall panels, ground freezing, deep soil mixing, dewatering, and over-excavation and backfilling). This paper focuses on challenges with launch and reception of pressurized-face TBMs with precast concrete segment linings. Challenges related to pipe jacking are discussed in a separate paper titled ?Mitigating Microtunnel Launch and Reception Challenges? (Hunt and Finney 2008).

Jan 1, 2008

By P. Dhar, H. R. Kota, M. Thornhill

Precipitated calcium carbonate is used as a filler and coating material in the manufacturing of paper because of its high brightness and light scattering characteristics. However, beneficiated calcite has similar potential, given the fact that the industrial specifications are already achieved. For paper industries, the requirement is that the desired product should be pure and have a brightness of 93 to 95 percent. A very-high-grade calcite deposit of around 92 percent is located in the north of Norway, which is used as the raw material for ground calcium carbonate (GCC) feed for the paper industries. There is a substantial amount of calcite resource, which has pyrite and pyrrhotite as major impurities. These sulfides, even when present in minor concentrations, impart color to the end product (paper). Removing these minerals is estimated to increase utilization of the deposit by 10  percent, which represents several million tonnes of calcite marble. Due to the requirement for environmentally friendly reagents and chemicals by the mineral industry, fatty di-amines are being tested for pyrite and pyrrhotite flotation. The interaction mechanism of diamine with the main components of the ore were studied and optimum conditions for removal of sulfide impurities are outlined.

By Jack Parker

Critical width Before we go further into pillar design, we should look into the matter of "critical width," because of its effect on pillar behavior. Critical width refers to the greatest width that the rocks above the mine can span before failure or, if there are pillars, the width to which we must mine before the pillars accept the full weight of the overlying materials. There are theories to help calculate that probable width, and they usually boil down to one-quarter or one-third of the depth of cover; but they don't always fit, and it would be better for us to understand the factors that control local conditions. Critical width may be controlled by the thickness or strength of one or more of the strata above the mining horizon. In a gold mine, we might have a thick granite or basalt above us, perhaps capable of bridging across most or even all of a small ore body. In that case, pillars might have to support nothing, or perhaps just the weaker or damaged rock below the strong main roof. Obviously it would be wrong to design for tributary load on pillars based on some lab-determined rock strength. In some coal mining districts in Utah, huge steps can be seen in the mountain sides, with slopes on weathered shales and vertical cliffs 100 or 200 ft high in thick, hard sandstones. The sandstones are capable of bridging across hundreds of feet, often making mining deceptively easy at first, but it becomes more difficult as greater areas are opened. Sometimes such a mining sequence leads to violent bumps and bursts as the wide spans of sandstone sag and bear down on the working faces, like giant nutcrackers, or as bridges eventually fail, releasing much pent-up energy.

Jan 1, 1993

By Richard M. Chamberlin

Perlite is an altered rhyolitic glass with 2 to 5 wt % water that expands or "pops" when heated quickly to plasticity while evolving steam to form lightweight, glass foam. Commercial perlite deposits in New Mexico are well-developed zones of chemical weathering (hydration) superimposed on highly permeable and thick glassy zones at the chilled upper surface and toes of high-silica-rhyolite lava flows and lava domes. The maximum tonnage of glass in these volcanoes was predetermined by their unique eruptive histories. New Mexico perlite production (80% of US production of 571,00 st) is mostly from the 3.9 Ma high-silica-rhyolite lava flows at the No Agua Peaks volcanic center. The primary vent at No Agua is defined by a 900 ft-high rubidium-rich composite lava dome, known as West Peak, that contains minor perlite reserves. Slightly less rubidium-rich lava squeezed out from under the west flank of the dome to form relatively thin (250 ft) but highly vesicular lobate flows that now consist of about 50 % recoverable perlite. Finally, rubidium-poor lavas were extruded from a radial dike on the northeast flank of the dome. These thicker (400 ft) flow lobes contain about 20 % recoverable perlite. The largest mass of lava does not always contain the most perlite. The thinner (west) flow at No Agua yields the largest perlite reserves rather than the large composite lava dome or thicker (east) flow.

Jan 1, 1994

By John H. Bassarear

The never ending search for lower unit costs led Pima Mining Company's management to study various alternatives shortly after Expansion III was completed. It soon became apparent that a considerable amount of ore assaying 0.35% copper had to be moved in order to maintain mill feed at the desired 0.54% copper content, which is the overall grade of the ore reserves. Detailed investigations revealed that for a period of 8 - 10 years, about 14,000 tons per day of 0.30 - 0.40% copper ore would pass by the crusher en-route to the low grade stockpile. This ore is very hard, very clean and has to be mined at a relatively uniform rate. A six month pilot plant run testing autogenous and semi-autogenous grinding gave very encouraging results. Since no mining costs need to be charged to the extra tonnage (it had to be mined anyway) the only major costs would be against milling. The decision to proceed was made in August 1970 and Fluor-Utah was retained as the prime design construction contractor. Ore was first put through the new mill on December 29, 1971. By March of 1972 design tonnage of 14,000 TPD had been attained. The first three expansions at Pima Mining Company, 20 miles south of Tucson, increased mill capacity from 3,000 TPD to 36,000 TPD. These expansions included a separate, conventional, three stage crushing plant plus additions to the existing concentrator that primarily duplicated the then current flowsheet. Expansion IV, however, consisted of an entirely new and separate primary crusher and a completely new mill building located about 2,000 feet southeast of the 01 d concentrator. The new mill, using semi-autogenous grinding, produces scavenger and rougher flotation concentrates that are pumped to the old mill for regrinding, cleaning, thickening and filtration.

Jan 1, 1973

By Jennifer B. Leinart

Sixty percent of the mines responding to the sixth annual Mining Cost Service labor survey reported increases in wages averaging 3.4% over the preceding 12 months. Only one mine reported a decrease in wages and this was accompanied by initiation of a substantial profit-sharing plan. Thirty-nine percent reported no change in wages. Thirty-seven percent reported using some form of incentive bonus plan. Mining Cost Service annually surveys coal, metal, and industrial mineral mines throughout the United States. Information about wages, benefits, and incentive bonus plans is part of an extensive data collection program to monitor cost areas of significance to the mining industry. This year, 131 mines responded to the survey. The data is collected by sending questionnaires to personnel managers at active mining operations. The information included in this article was taken from the returned forms, from labor contracts provided by some of the mines, and from followup telephone calls. This year's data was collected between November 1988 and February 1989.

Jan 1, 1990

By Ann L. Backstrom

The Apex Tunnel is part of the Southern Nevada Water Authority?s proposed Clark, Lincoln, and White Pine Counties Groundwater Development Project. The project is intended to develop unused Nevada groundwater for meeting the water needs of Southern Nevada and would involve over 322 km (200 mi) of water transmission facilities. The Apex Tunnel, as currently conceived by ongoing planning and environmental analyses, would extend 2804 m (9,200 ft) through a structurally complex terrain of Paleozoic carbonate rocks and younger basin fill deposits and will traverse both public and private lands. Several faults cross the tunnel study area, juxtaposing rocks of varying lithology and degree of folding, and creating intervals of differing rock conditions along the tunnel alignment. This paper discusses how the geotechnical program was developed to be flexible and allow for rapid implementation of revisions based on new knowledge that became available during program execution, resulting in more effective decision making and enhanced value from the geologic investigation during the planning phase of the project.

By G. Avolio, M. Gilbert

INTRODUCTION The city of Alexandria, Egypt is located on the Mediterranean Sea at the northwestern edge of the Nile River delta. The city is approximately 26 km long and 3 km wide bounded by the sea to the north and Lake Maryut to the south. The Alexandria Project is split into 2 phases: phase one included designs to update two existing primary wastewater treatment plants, five pump stations and over 75 km of sewer pipe, 18 km o f which is tunneled, (1500mm to 2750mm ID pipe). Currently the pipeline and pump stations are under construction. Phase two of the project includes expanding both the capacity of the treatment plants and the limits of the collection system. Included in this system expansion is the 3.5 km long, 2250mm ID Central Zone Conveyance, which is the subject of this paper. The project is under the direction of The Alexandria General Organization for Sanitary Drainage (AGOSD). It is an USAID funded joint venture of two American firms, CH2M - Hill and Metcalf & Eddy who share equally the major portion of the work and two Egyptian firms, Engineering Consultants Group (ECG) and Wairth Associates who are also partners. The venture, which is both design and construction management, worked under the name Wastewater Consultants Group, WWCG. Michael Gilbert was Chief o f the Geotechnical Department and Project Engineer for the Central Zone Conveyance. Gennaro Avolio was Geotechnical Exploration Manager for the Alexandria Wastewater Project.

Jan 1, 1987

By John E. Newby

Washington?s King County is constructing a new regional wastewater treatment facility, called Brightwater, in response to growth in the greater Seattle region. Planning conducted in the late 1950s identified the need for two regional treatment facilities. Constructed in the 1960s, these plants have served the region well. However, an eventual need for a third facility was also recognized. The Brightwater project implements the final phases of the long-term plan. The project includes a new treatment plant and an extensive conveyance system. When completed in 2010, the Brightwater facilities will treat sanitary sewer flows from growing populations living in northern King County and southern Snohomish County. The new system will fulfill commitments to provide wastewater services to local jurisdictions and sewer service providers in the King County Service Area. It will also provide more flexibility in the operation of the King County regional wastewater system. The Brightwater wastewater treatment plant will provide secondary treatment capacity using membrane bioractor technology in 2010 for 36 million gallons per day (mgd), with anticipated expansion in 2040 to 54 mgd, using membrane bioreactor technology. These capacities are for average wet-weather flows. The plant will also accommodate peak hourly flows of 130 mgd by 2010 and 170 mgd by 2040. The Brightwater Conveyance System consists of more than 8.1 km (13 miles) of tunneled influent and effluent conveyance lines, five tunnel portals/shafts, microtunneled influent and outfall connec-

Jan 1, 2007

Many states rely upon the Pennsylvania 1957 “Gas Well Pillar Study” to evaluate the coal barrier surrounding gas wells (Commonwealth of Pennsylvania, 1957). The study included 77 gas well failure cases that occurred in the Pittsburgh and Freeport coal seams over a 25-year span. At the time, coal was mined using the room-and-pillar mining method with full or partial pillar recovery, and square or rectangle pillars surrounding the gas wells were left to protect the wells. The study provided guidelines for pillar sizes under different overburden depths up to 700 ft. The 1957 study has also been used to determine gas well pillar sizes in longwall mines since longwall mining began in the 1970s. The original study was developed for room-and-pillar mining and could be applied to gas wells in longwall chain pillars under shallow cover. However, under deep cover, severe deformations in gas wells have occurred in longwall chain pillars. Presently, with a better understanding of coal pillar mechanics, new insight into subsidence movements induced by retreat mining, and advances in numerical modeling, it has become both critically important and feasible to evaluate the adequacy of the 1957 study for longwall gas well pillars. In this paper, the data from the 1957 study is analyzed from a new perspective by considering various factors, including overburden depth, failure location, failure time, pillar safety factor (SF), and floor pressure. The pillar SF and floor pressure are calculated by considering abutment pressure induced by full pillar recovery. A statistical analysis is performed to find correlations between various factors and helps identify the most significant factors for the stability of gas wells influenced by retreat mining. Through analyzing the data from the 1957 study, the guidelines for gas well pillars in the 1957 study are evaluated for their adequacy for room-and-pillar mining and their applicability to longwall mining. Numerical modeling is used to model the stability of gas wells by quantifying the mining-induced stresses in gas well casings. Results of this study indicate that the guidelines in the 1957 study may be appropriate for pillars protecting conventional gas wells in both room-and-pillar mining and longwall mining under overburden depths up to 700 ft but may not be sufficient for protective pillars under deep cover. The current evaluation of the 1957 study provides not only insights about potential gas well failures caused by retreat mining but also implications for what critical considerations should be considered to protect gas wells in longwall mining.

Jul 28, 2020

By Narendra N. Khatri, Michael Deutscher, Jozef F. Zurawski

Five sewer connections were required to divert Combined Sewer Overflow (CSO)from existing outfalls to an old underutilized large diameter brick sewer (the Easterly Interceptor). The connections were part of an on-going CSO control program by the Northeast Ohio Regional Sewer District (NEORSD) in the City of Cleveland, Ohio. Each connection was made by pipejacking and hand-mining a fiberglass-reinforced polymer (FRP) pipe through soft glaciolacustrine clays and silts. Jet grouting was utilized to stabilize the soils and fill the voids surrounding the interceptor prior to making the underground connection. Reinforced concrete liners were constructed inside the aging brick sewer to provide structural stability during ground improvements and connection work. The project also involved micro tunneling two approximately400 foot lengths of FRP pipe through soft ground using a slurry pressure balanced machine.

Jan 1, 2005

By T. W. Beck

Drilling into coal mine roof strata to install roof bolts has the potential to release substantial quantities of respirable dust. Due to the proximity of drill holes to the breathing zone of roof bolting personnel, dusts escaping the holes and avoiding capture by the dust collection system pose a potential respiratory health risk. Controls are available to complement the typical dry vacuum collection system and minimize harmful exposures during the initial phase of drilling. This paper examines the use of a bit sleeve in combination with a dust hog-type bit to improve dust extraction during the critical initial phase of drilling. A twisted-body drill bit is also evaluated to determine the quantity of dust liberated by comparison to the dust hog-type bit. Based on these laboratory tests, the bit sleeve may reduce dust emissions by one-half during the initial phase of drilling before the drill bit is fully enclosed by the drill hole. Because collaring is responsible for the largest dust liberations, overall dust emissions can also be substantially reduced. The use of a twisted-body bit has minimal improvement on dust capture compared to the commonly used dust hog-type bit.

Feb 27, 2013

By William X. Chavez

The Mantos Blancos copper-silver district, a major copper-producing area since 1961, is located on the Tropic of Capricorn about 45 kilometers northeast of the northern Chile port city of Antofagasta, as shown in Figure 1. Copper oxide minerals occurring as atacamite (Cu C1(OH)3) and chrysocolla (copper silicate-hydrate) were discovered in the district in the early 1900's (Knobler and Joseph, 1962). The mine is situated in the northern Atacama Desert, one of the most arid regions on earth, and presently receives less than 1 cm per year of precipitation. The extreme aridity of the Atacama Desert is thought to have prevailed since at least Middle Miocene time (Mortimer et al., 1978) when development of important supervene copper enrichment was slowed in many areas of northern Chile (e.g., Chuquicamata, Exotica). Despite the paucity of precipitation, landform development is mature, with large alluvial fans and alluvial-filled valleys covering much of the region. In addition, the aridity and presence of salts have led to the formation of a sub-surface cementing of alluvium and colluvium by halite-rich caliche ranging from a few centimeters to over 3 meters in thickness. These factors, resulting in poor outcrop exposure, make even reconnaissance mapping difficult.

Jan 1, 1983

By M. Okido, W. Wei, L. Chai

The kinetics on the growth of Thiobacillus ferrooxidans was studied by use of series piezoelectric quartz crystal ( SPQC ). Arsenic ioninhibits the growth of Thiobacillus ferrooxidans, which is consistent with the previous results by other measuring method. This further demonstrates that the SPQC can monitor the chemical activity of the growth of Thiobacillus ferrooxidans. Cupric ion accelerates the growth of Thiobacillus ferrooxidans. The mechanism was discussed, it was considered that copper promotes the protein enzyme of Thiobacillus ferrooxidans, rustic yanin, to form over the range of cupric ion concentration studied. There action order of cupric ion in accelerating the bacterial growth is 0.067. The growth of Thiobacillus ferrooxidans is dependent on temperature, the apparent reaction activation energy decreases from25.56 kJ / mol to 18.32 kJ / mol because of the addition of 10 mg / L Cu(II) to the bacterial growth solution of pH 2.0 at initial inoculum of 10%.

Jan 1, 2000

By Andrew Kaczmarek

The mining industry is enjoying a much needed and long awaited increase in demand for natural resources. However, consolidations in the mining and mining service industries, along with a generational departure of experienced industry professionals, is challenging today’s mining companies. These challenges are not only in maintaining their existing operations, but also in securing qualified resources for developing new projects. These challenges are compounded for junior mining companies. They oftentimes lack for operating properties to draw experienced professionals from. Also, juniors have to compete with the majors’ “mega-projects” for experienced project personnel from the reduced ranks of engineering companies. This article discusses some strategies developed by Anatolia Minerals Development (Anatolia) in developing its Çöpler gold project in central Turkey.

Jan 1, 2006

By W. Blake, J. Whyatt

Sixty years of rockbursting in the Coeur d’Alene district has taught painful lessons and led to a number of practical advances in controlling rockburst hazards. This paper summarizes those lessons, concentrating on practical measures that have been successfully adopted to reduce hazards. These lessons are explained in the context of district mining history and current understanding of rockburst phenomena. Overall, the paper provides the practicing mine engineer with an appreciation of rockburst hazards and an overview of practical measures that can be used to control these hazards in the context of Coeur d’Alene district experience.

Jan 1, 2002

By Don F. Macfarlane

This paper describes the field application of the NTH fracture classification to rock encountered in the construction of the 9.6 km long, 10m diameter, Second Manapouri Tailrace Tunnel. Excavation of the tunnel was undertaken by TBM between 1997 and 2002, in gneisses, granitic and diorite rocks. The paper outlines an adaptation of the NTH fracture classification used during the geological logging of this tunnel. The NTH fracture classification was primarily applied to assess discontinuity spacing for tunnel support requirement decision-making. The paper includes some general comparison of NTH classes with overall penetration rate.

Jan 1, 2008

By 1980, the U.S. mining community had reached a broad consensus regarding coal pillar design. The pillar load could be estimated from tributary area theory, and the pillar strength from empirical formulas and laboratory coal strength testing. Then the growth of longwall mining required new thinking. Recently, powerful design methods have emerged from analysis of large data bases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark-Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. Sophisticated numerical models have also helped transform the pillar design landscape. In the process, our understanding of pillar mechanics has been greatly enriched. A new paradigm divides pillar failure into three categories:

Jan 1, 1999

By H. Haselhuhn

Filtration of hematite ore slurries can be a bottleneck in some hematite processing plants due to inadequate filtration rates caused by the dispersion of fine particles. Flocculation of fine particles in the slurry decreases the specific cake resistance of the filter cake allowing for increased filtration rates. CO2 sparging of hematite slurry was shown to increase the filtration rate by altering the pH and the surface chemistry of the particles. It was shown that an increase in filtration rate of 278% can be accomplished by lowering the pH from 11 to 6.5 using CO2. This was attributed to increased flocculation of hematite and silica particles in the ore.

Jan 1, 2012

By Miles T. Stephens, Felipe Calizaya, Jacob O. Kingston

Currently, the Bear Canyon Mine is facing the challenge of excessively high coal and rock temperatures in one of its headings. In Mine No.3, the air temperature at the 6th Right panel reached 36.4ºC and the coal 83.9 ºC. Due to these severe work conditions, the mining plan has been altered by changing the mine direction to avoid the high temperatures. To investigate the problem, drill holes were developed from the entries and the rock temperatures monitored using K-type thermocouples. The measurements confirmed the existence of localized “hot spots” in the mine. This paper presents a summary of ventilation surveys that were conducted in this mine. It includes the results of coal and rock temperature measurements from drill holes, interpretation of results using a heat flow simulator and the identification of hot spot areas. It also includes a summary of methods that were developed to reduce the hazard and control the problem.

Jan 1, 2005