Search Documents

By Gregory Yates

INTRODUCTION Project Description The Silver Line is a Bus Rapid Transit (BRT) Line and is Boston?s newest transit service. Silver Line Phase I extends along Washington Street entirely on the surface in priority bus lanes from Dudley Station in Roxbury through the South End and Chinatown neighborhoods to downtown Boston. The Phase I opened in July 2002. Silver Line Phase II consists of an underground transit tunnel from South Station to the South Boston Waterfront with underground stations at Courthouse and World Trade Center to Silver Line Way east of D Street. Phase II continues through the Ted Williams Tunnel to all the terminals at Logan Airport, and on the surface to the Boston Marine Industrial Park and City Point. Phase II opened in December 2004. Silver Line Phase III is a one mile tunnel connection to the existing Phase II tunnel in the vicinity of South Station and will eventually portal on Tremont Street just north of Marginal Road. After leaving the portal, the buses will use dedicated bus only lanes on the surface roadway network to connect to the Phase I service. Figure 1 shows the alignment of the Silver Line upon completion of the Phase III project.

By Y. Luo

"It is generally known that spontaneous combustion potential is a function of coal rank, with low-rank coals having high susceptibility to self-ignition and high-rank coals having low potential. To establish this functional relationship and use it as an engineering tool to identify the propensity of coal to self-heat, both rank and spontaneous combustion potential should be quantified. ASTM D388 is normally used to classify coals by rank, but this classification system can only serve a qualitative analysis. To classify coals by their potential for spontaneous combustion, the self-heating temperature (SHT) method originally developed by the U.S. Bureau of Mines (USBM) was used by Litton and Page (1994) to correlate coal rank with spontaneous combustion potential. In that method, the SHTs of coal determined by an adiabatic experiment are linked with proximate analysis results through a proposed concept known as the “moist fuel ratio.” This ratio is a function of moisture, volatile matter and fixed carbon, all of which have widely different content percentages in different ranks of coal and have strong relationships with coal rank. However, the method is highly empirical, and there is large standard deviation between experimental data and calculated results. The equation correlating the coal quality parameters to determine SHT should be improved with more experimental data.This paper reports on the development of a new system for predicting the spontaneous combustion potential of U.S. coals, based on coal composition data from the U.S. Geological Survey’s coal quality database. First, the user is provided with a quantified classification of coal rank. Second, based on experimental SHT data covering a wide range of ranks from lignite to low-volatile bituminous coal, the original USBM correlation for predicting SHT is improved for the respective rank of coal. The relationship between the rank and SHT of U.S. coals was developed and plotted. The plot diagram can be used for a quick estimate of the SHT of a U.S. coal and as a cost-effective tool for the initial risk assessment of a new mine development."

Jan 1, 2015

By R. D. Peterson

As underground mine operations expand, the ventilation systems supporting them become complex. Complexity increases with periodic ventilation changes. New diagonal connections require a rebalance of resistance to maintain airflow in affected splits in the system. Incidents of mine fires and explosions have occurred in U.S. coal mines when diagonal connections resulting from ventilation changes have resulted in changing airflow directions. MSHA regulations prohibit the reversal of airflow and poor ventilation practice in general, but regulations cannot stipulate or recommend proactive preventative measures because every situation is different. This paper discusses the phenomenon of diagonal branches and recommends practical precautionary measures that can be taken to prevent airflow reversal in planned ventilation changes.

Jan 1, 2012

By J. Hollow, D. Walsh

The Fort Knox Mine is located in Alaska’s interior, where the average ambient air temperatures range from -24oC in January to 16oC in July. The mill processes a free milling gold ore utilizing both a gravity recovery circuit and a conventional cyanide leach/carbon-in-pulp circuits. Mathematical models have been developed to accurately predict the impact of leach circuit slurry temperature on gold leach, carbon adsorption and cyanide destruction kinetics. Additionally, an energy balance approach has been used to model the seasonal variations in slurry temperatures throughout the Fort Knox mill. The energy balance model, combined with the kinetics models previously developed to predict plant performance, was used to justify a tailing thickener installation at the Fort Knox Mine. This paper describes the development of the energy balance model and its prediction of plant performance assuming a tailings wash thickener to reduce heat loss from the mill. Also presented is an analysis of the post project plant performance that validates the model and shows the mine produced an additional 596 kg (19,155 ounces) of gold, while reducing mill reagent costs by $6,302,000 during the first 38 months of operation.

Jan 1, 2007

By Michael Gobla

"Since 1994 the Bureau of Reclamation (BOR) has used risk analysis to evaluate dams. Risk considers both the likelihood of failure and the expected consequences should failure occur. Risk analysis relies on the detailed formulation and critical analysis of all possible potential failure modes. Potential failure modes are formulated by describing the sequence of events that must occur to result in failure, where failure is defined as the uncontrolled release of the impounded reservoir. Failure occurs in response to loadings such as water seepage through a dam (static forces), shaking from an earthquake (dynamic forces), sudden flood inflows (hydrologic forces), or accidental overfilling (operational errors). Reclamation has, to a limited extent, applied risk analysis to inactive and abandoned mines to evaluate tailings dams, pit lakes and flooded underground mines. Case histories of potential failure mode analysis, as applied to mine impounded water, illustrate what critical technical information is needed to determine if failure is likely, what the consequences of failure are likely to be, and what are the highest risks that should be addressed first.IntroductionImpounded water and high water content wastes at mining and industrial processing sites are potential threats to public safety and the environment. Recent failures such as the TVA Kingston flyash impoundment failure in Tennessee in 2008 (4.1 million m3 or 5.4 million cu yd) release, the Mt. Poly Tailings Dam failure in British Columbia in 2014 (4.4 million m3 or 5.8 million cu yd) release, and the Samarco Fundao Tailings Dam failure in Brazil in 2015 (59 millon m3 or 78 million cu yd) release have renewed attention to this issue. Potential risks from impounded water at mining and industrial sites originate not only from tailing dams, but also from water in process ponds and conveyance pipelines, sediment retention dams, water retention dams, mine pit lakes and flooded underground mine workings.Conventional water retaining dams also have a record of failure. Notable examples of failure include Vajont Dam in Italy in 1963 (2,600 lives lost), Banqiao and Shimantan Dams in China in 1975 (171,000 lives lost), and Machhu-II Dam in India (10,000 lives lost). After the 1976 Teton Dam failure in Idaho, the U.S. Bureau of Reclamation (BOR) established a Dam Safety Program. By 1984, the agency developed and began using risk analysis methods. BOR operates and maintains an inventory of hundreds of aging dams which were designed and constructed over a period of 100 years. Many of these facilities were designed and constructed prior to the development and adaptation of modern soil mechanics in dam engineering. Diligent observational monitoring, detailed site investigations and the application of risk evaluation to the BOR dam inventory has identified many deficiencies resulting in significant demands on available funding for remediation efforts. The application of risk analysis has allowed the agency to rank sites by risk. By giving priority of remedial efforts to high-risk sites, significant improvements to dam safety have been achieved."

Dec 1, 2016

By H. Lyn Bourne

This is the fifth annual tabulation of mineral royalty information. This tabulation, like the previous editions, includes all of the earlier data. There are also 60 new entries. In addition to royalty information, some entries show the cost of purchased reserves. Two articles relative to the evaluation of minerals reserves appeared in December, 1986. R.H. Paschall (In the Aggregate, ME, p 1139) wrote a good article, although it lacked specific royalty data. However, this author takes exception to two ideas in Paschall's column. Paschall contends that the royalty rate does not affect the mineral appraisal. This present author could not disagree more. Paschall also claims the location of an industrial mineral deposit is the only serious or practical caveat in comparing royalties. Comments received here from readers helped make the list of caveats that are cited each year. The readers will decide which factors influence the mineral value for their commodities of interest. Paschall's point about the relationship of the parties who are negotiating a royalty agreement is important and very well taken. The other article, written by William Vernon (Pit and Quarry, December 1986), gives a step-by-step process on how to conduct a mineral appraisal. The article cites three reasons for an appraisal: transfer rights; collateral for a loan; and taxation. A fourth reason is to establish adequate compensation for reserves lost through condemnation. This author has appeared in several court cases where compensation for loss of mineral reserves through condemnation required a mineral appraisal. Royalty rate becomes an important factor in the appraisal process, although the Pit and Quarry article refers to that part of the valuation equation as "profitability." Both articles were well written and are recommended reading for those interested in mineral valuations. The same caveats that have appeared in previous columns relative to factors that influence the value of reserves are restated. The data in the table serve as a general reference and are not intended to present an absolute scale of reserves costs. Several factors influence the value of any mineral commodity. The factors include: • location/transportation - especially significant for most industrial minerals; • market conditions both for the commodity and the company acquiring the right to mine; • quality or grade of the deposit as it reflects the amount of processing/beneficiation necessary to produce the finished product; and • legislative restrictions and conditions for mining a given material at a given site. These and other factors will significantly influence the cost of reserves. The table shows the range of royalties and the variations in the basis of computing the fees. In a few instances, it gives the cost of acquired reserves based on purchase price and quantitative estimates of the material in place. The table lists the commodity in column 1, and the subsequent columns give: • the location by state, US geographic area, or Canadian province ; • the cost - R for royalty and P for purchased cost; • the year in which the lease or purchase agreement occurred; and • comments or footnotes for more information. The cost column requires more explanation. The units may refer to cubic yards (/cu yd), cubic feet (/cu ft), short tons (/T), or acres (/A). 1 cu yd = 0.76 M2 1cuft = 0.28m3 1 st = 0.9072 t 1 acre - 0.4047 ha or m2

Jan 7, 1987

By Stuart F. McTavish

Mechanically suitable grinding mills became available to the mining industry in 1908. Since then, mill operators have been searching for the best material and design with which to line the mills. These liner systems had to fulfill several criteria. Most important, they had to last long enough in an operating mill to protect its structure from the abrasive wear of the ore and the grinding media. In addition, they had to be capable of efficiently transferring the energy from the mill to the mill charge in order to facilitate the grinding process. And these liners had to be easy to install and remove. The first liners used were generally made of cast white iron, Hadfield manganese, unalloyed high-carbon steel and composites of steel and concrete or cemented in flint blocks or natural stone. In the early 1920s, pieces of solid rubber truck tires were used as emergency repairs for broken cast metal liners. Thus was rubber first introduced as a mill liner material. The first patent for rubber mill liners was awarded in 1921 to James Denny and Rolla Watson, both of the Coniagas Mine in Cobalt, Ontario, and to Dale Barnum of the Comstock Lode in Virginia City, NV. This original design was covered under US Patent No. 1470597. It had a fabric backed rubber that was bonded to the shell of the mill.

Jan 1, 1990

By A. Davis

Pit lake chemistry depends on the lithology and hydrologic characteristics of the ultimate pit surface, the availability of buffering capacity in the wall rock versus oxidizable sulfide content, and the alkalinity of recharging ground water. In this paper, we assess the geochemistry of 11 existing pit lakes, ranging from the acidic Red Hill and Berkeley pit lakes (pH 2.6 to 2.8) to the alkaline Yerington Pit lake (pH 8.45). Predicted pit lake chemistry is similar to that in existing pits with the long-term pit lake chemistry lying on a geochemical continuum between end members consisting of influent calcium bicarbonate ground water, and naturally occurring sulfate-rich evaporite playa lakes.

Jan 1, 1996

By Mina M. Shinouda

Brightwater West (BT4) represents the state of the art in utility tunneling, namely a long relatively small diameter, soft ground tunnel, with no intermediate shafts, under significant groundwater pressures, requiring very precise survey control in order to hit a small exit window. The tunnel is over 6.4 km (4 miles) in length, is expected to encounter active earth pressures of over 5 bars in glacial geology, and a planned hole through into a shaft eye constructed at 45.7 meter (150 feet) below the water table. Despite the fact that all of these challenges have been previously overcome in larger diameter tunnels, the technical solutions are much more challenging in a smaller diameter due to the lack of space available for implementing the equipment and techniques required. In addition to the technical challenges, the project is faced with many of the constraints designed to minimize the impact of these types of projects on the neighboring community and environment. The work shaft for BT4 is within 15.2 m (50 feet) of Puget Sound and is on a site that was previously occupied by petroleum storage tanks, and all of the tunnel muck has to be removed from the site by barge as trucking is not allowed by contract. The paper addresses the work performed during the preparation for tunneling stage of this project both in assembling the TBM and in preparing the site for its arrival.

By P. C. Thakur

In Part I of this paper, it was established that the width of longwall faces in highly gassy mines is primarily limited by the volume of air reaching the tail-end of the face. The ventilation air reaching the tail-end of the face should be not only enough to keep methane concentrations below the statutory limits (generally 1 percent) but also enough to prevent any gas layering. The air volume leaking from the longwall face into the gob should also be able to push the explosive methane-air mixture away from the gob area immediately behind the longwall face where active roof-fall is taking place (typically 30-45 m). The second group of variables that also controls the width of the longwall panel consists of (a) the rate of advance, (b) bleeder air quantities, (c) specific methane emissions for the gob area and, (d) efficiency and cost of gob gas capture. This paper will discuss the second group of variables and its impact on the optimum width of longwall faces in highly gassy coal mines.

Jan 1, 2009

By Andy Davis

The evolution of pit lake water quality depends on the lithology and hydrologic characteristics of the ultimate pit surface, the availability of buffering capacity in the wall rock vs. oxidizable sulfide content, the alkalinity of recharging groundwater and the evapoconcentrative characteristics of the system. This paper assesses the geochemistry of 11 existing pit lakes, ranging from the acid Red Hill and Berkeley pit lakes (pH 2.6 to 2.8) to the alkaline Yerington pit lake (pH 8.45). Predicted pit lake chemistry is similar to that in existing pits, with long-term chemistry lying on a geochemical continuum between end members that consist of influent calcium bicarbonate groundwater and naturally occurring sulfate-rich evaporate playa lakes.

Jan 1, 1997

By Bruce Hebblewhite

This paper focuses on the recent achievements and practices developed through the Minerals Tertiary Education Council (MTEC) initiative of the Minerals Council of Australia (MCA), in conjunction with the three partner universities involved in mining engineering education – University of New South Wales (UNSW), West Australian School of Mines, Curtin University (WASM), and University of Queensland (UQ). The collaboration between these partner universities and industry has led to the development of shared course material, cross-institutional teaching arrangements, and development of a number of flexible, distance-based delivery programs. The paper will then move on to future initiatives. Importantly, the exciting challenge is the future initiative planned to cement this collaboration by the formation of a “virtual” national school of mining engineering – Mining Education Australia (MEA). This will provide a common 3rd and 4th year program to all three universities from 2007, involving innovative teaching and learning arrangements, greater student exchange potential and a more significant input by industry into the education process. Such an initiative is not without its challenges, and has a long way to go, before becoming a reality. However, it offers greater attractiveness and marketing potential to prospective students, as well as economic efficiencies, whilst delivering a better quality, and hopefully greater quantity of graduates to industry. It can also form a launching platform for a much greater level of international collaboration, through a proposed International Mining Education Network (IMEN) which is currently being floated amongst a number of international educators.

Jan 1, 2005

By H. Kinilakodi

In 2008, the authors developed a methodology for identifying underground coal mines at high risk for major-hazard events. It focused on major hazard-related violations of safety standards associated with high-risk conditions. Later, using a sample of 103 mines with 2008 and 2009 data, injury measures and U.S. Mine Safety and Health Administration (MSHA) citation data were combined into a safe performance index (SPI). The SPI was used to assess the relative safety-related risk of mines, including by mine-size category. In this paper, comparisons are made of SPI-associated, normalized safety performance measures across mine-size categories, with emphasis on small-mine safety performance as compared to large and medium-sized mines. Mining Engineering, 2011, Vol. 63, No. 10, pp. 73-77. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By Josh B. Taggart

Some twenty to twenty-five years ago we saw the beginning of mechanization in our coal mines, It has now progressed to the point Chat as instruments of production the pick and shovel are things of the past, They had to give way to better and more efficient methods--so mechanization, followed by and combined with automation, has become common-place in our mines. Our coal could not keep its competitive position without this progress Without it our industry could not look to the future with any degress of confidence. Today we lock back and see cases of regained and salvaged markets. We see better coal products being produced at decreasing costs. We see better utilization of manpower and a stronger, more confident industry, Our hats arc off to those mining men, equipment manufacturers, labor leaders, and others who had the foresight to work toward these ends and the ability to bring them about.

Jan 1, 1962

By H. C. Liang

Reverse osmosis (RO) and nanofiltration (NF) are widely regarded as being best available technologies (BATs) for removing contaminants of concern from water. In recent years, NF or RO treatment has increasingly gained more acceptance in the mining industry for treating mine water to remove a wide assortment of contaminants, either for meeting discharge standards or for internal re-use in mining processes. Consequently, the number of NF or RO membrane mine water treatment facilities has steadily increased. Although NF or RO membrane filtration can be a powerful tool in mine water treatment, especially when multiple contaminant removal is required, it also has many potential disadvantages. Besides the generally higher capital and operational costs for the high pressure membrane processes, organic constituents in mine water may foul the membranes, while inorganic compounds such as gypsum, calcite, or silica are liable to scale the expensive membranes if proper pre-treatment processes are not implemented. Additionally, because these membrane treatment processes generate a substantial reject or brine waste stream in addition to the clean treated water or permeate stream, brine management also needs to be considered carefully when deciding upon the viability of an NF or RO mine water treatment process. Because of these issues, it is important to conduct detailed analyses of the trade-off between selecting NF or RO vs. using chemical treatment processes when designing a mine water treatment facility.

Jan 1, 2012

Most statistical and geostatistical methods of re-source and reserve estimation work extremely well for Normal (Gaussian) well-behaved information. However, most interesting mineral deposits exhibit far from this idealistic distribution of values. It seems that the more valuable the mineral, the less likely the data are to have a Normal distribution. Values tend to be "positively skewed" with a long tail into the high values. Using averaging techniques, such as inverse distance or ordinary kriging may result in consider-able overestimation of grades and tonnages unless such values are cut or otherwise modified. This paper presents some real case studies where distributions are (a) highly skewed and (b) the product of multiple phases of mineralisation. Practical methods are presented for solving such problems including combinations of indicator and log normal kriging methods. The emphasis of the presentation is on developing operational methods which can be used on project evaluation or grade control in producing mines.

Jan 1, 2000

By Gordon T. Clark, James R. Struthers, Celal Kirandag

INTRODUCTION Project Background The Washington State Department of Transportation (WSDOT) hired the Seattle office of Parsons Brinckerhoff to lead a team of consultants to produce an Environ-mental Impact Study and perform conceptual and preliminary engineering. The pur-pose of the Alaskan Way Viaduct and Seawall Replacement project is to replace the existing earthquake damaged and aging viaduct and sea wall, adjacent the downtown waterfront of Elliott Bay, with structures that have improved earthquake resistance and that maintain or improve mobility and accessibility for people and goods along the existing corridor. With an estimated replacement cost over $4 Billion and construction duration exceeding 8 years, it is one of the largest transportation design projects on the West Coast of the United States today. Seattle, Washington is a city of over 2 mil-lion people in the Northwest corner of the United States. Ever since the Klondike Gold Rush in 1897, Seattle has been considered a departure point to Alaska. Because of this, the street along the waterfront was named the Alaskan Way in 1930. Alaskan Way Viaduct and Seawall The Alaskan Way Viaduct (AWV) carries State Route 99 along the shoreline of Elliott Bay through downtown Seattle and is a vital part of Seattle’s highway system. The viaduct carries approximately 110,000 vehicles per day or 25% of all north-south traffic through Seattle (Figure 1). It is 3.4 km (2.1 mile) long with 3 lanes in each direction and was constructed of cast-in-place reinforced concrete between 1952 and 1956. The wear and tear of daily traffic, salty marine air, and several earthquakes have taken their toll on the facility. Studies in the mid-1990s provided early evidence that the viaduct was nearing the end of its useful life. The viaduct’s increasing age and vulnerability was apparent by crumbling and cracking concrete, exposed rebar, weakening column connections and deteriorating railings. In early 2001, a team of structural design and seismic experts began work to determine whether it was feasible and cost-effective to strengthen the viaduct by retro-fitting it. In the midst of this investigation, a 6.8 magnitude earthquake shook the Puget Sound region (the Nisqually Earthquake, located 56 km (35 miles) from Seattle and deep below the surface) caused moderate damage to the reinforced concrete structure. WSDOT closed the viaduct for inspection and repairs intermittently for several days over a period of several months.

Jan 1, 2007

By J. B. Hiskey

Introduction The domestic copper industry has suffered for some time from declining ore grades; rising costs associated with conventional mining, milling, smelting and refining; tightening environmental restrictions; and shrinking markets due to materials substitution. Ore grade depletion is a major problem. It is illustrated by the decline in average copper yield shown in Fig. 1. From 1979, copper grade has dropped 60%, lowering yields from 1.2% to 0.49% (Sousa, 1981). The US copper industry is taking drastic measures to enhance its competitive posture and to guarantee its future worldwide position. In a sense, this involves a general restructuring of the processing philosophy of US copper producers. Judging from recent trends, this restructuring relates to the application of solution mining techniques to the treatment of copper ores and low grade waste material. Recovering copper by leaching techniques has been practiced for centuries. As early as the mid-16th century, some Hungarian copper mines were recycling copper bearing leach solutions through waste heaps (Nash, 1912). In the US, recovering copper from dilute mine waters has been carried out for more than 100 years. There are, however, certain technical innovations that have elevated the importance of solution mining as a process for copper recovery. These include: • Advances in solvent extract-electrowinning (SX-EW); • Developments in acid and acid ferric cure processes for oxide and mixed oxide sulfide ores; • Improvements in heap and dump construction; and • Advances in in situ leaching technology. Generally, solution mining enjoys certain intrinsic advantages over conventional mining and milling. Compared to conventional milling, the combined capital and operating costs of leaching facilities are normally lower, start-up times are faster, and the leaching operation usually has less impact on the environment. Furthermore, solution mining represents an expedient way of extracting metals from small shallow deposits, and is particularly suited to the treatment of low grade sources. And, in the case of waste dump leaching, there is a tremendous resource in-place that has the mining cost already off the books. This paper updates current US copper solution mining trends. Solution mining systems Schlitt (1980) summarized the characteristics of the principle leach systems in the US. He pointed out that the wide variations in copper deposits make solution mining a more site-specific activity than conventional mining and milling. Heap leaching is usually selected for moderate to high grade ores having a copper mineralization that is amenable to acid leaching (oxides, silicates and certain sulfides). Higher grade ores mined specifically for heap leaching are usually treated to optimize copper extraction, therefore, crushing and some pretreatment (acid curing) may be justified. On the other hand, dump leaching practice usually involves leaching low grade waste rock placed on large dumps as dictated by topography and haulage costs. Mine waste is therefore treated in an uncrushed run-of-mine condition. Finally, in situ leaching is appropriate for either very deep ore bodies or for recovering copper from low grade rock left behind in abandoned pit walls, stopes, and subsidence zones from earlier mining activities. True in-situ solution mining should be defined as the leaching of ore in its original geologic setting. Heap leaching Heap leaching has a long history as a hydrometallurgical process for copper recovery. The methodology of heap leaching established at Rio Tinto in Spain more than 300 years ago is basically the same as that used today. Processing concepts, such as solution management (sprinklers and leach/rest cycles) and copper

Jan 11, 1986

By Peter Amelunxen, Brandon Akerstrom

Since its introduction 40 years ago, the compartmental model of flotation has been used to predict the performance of mechanical flotation cells. However, it has found limited success for modeling dual-chamber machines and, as a result, engineers have adopted empirical correction factors usually derived from field audits of industrial cells to predict the performance of dual-chamber flotation cells. This paper introduces an extension of the compartmental model that applies to both single- and dual-chamber cells. The model is tested against pilot test work performed at Capstone’s Pinto Valley concentrator, and then used to evaluate the key operating and design parameters of dual chamber flotation cells. The results suggest that the design of the mixing chamber — for example, whether it is pneumatic or mechanically agitated — is not a significant contributor to overall machine performance. The work also suggests that the highest recoveries are achieved when the froth recovery is high, and longer separation chamber residence times and/or higher internal circulating loads are only beneficial when the froth recovery is low. Lastly, the results show that the single most important driver of the machine performance is the froth recovery of the separation chamber.

Mar 1, 2025

By O. MacIntosh

The Round Mountain gold mine, located 90 km (55 miles) north of Tonopah, Nevada began large-scale production in 1977. During 2008 Round Mountain Gold Corporation (RMGC) relocated the primary crusher facility approximately 300 meters (1,000 feet) to make room for the next phase of open pit mining activities. This facility was installed in 1988 and used a log-crib retaining wall and dump pocket RMGC selected Hilfiker Retaining Walls and Collins Engineers, Inc. to provide design and materials for a new 17 meter (56 feet) high Mechanically Stabilized Embankment (MSE) wall to support the haul trucks at the new location. The construction contractor was EarthTech West Ltd. of Norwood, Colorado. An MSE wall with a cast-in-place concrete face was chosen as a durable, yet less expensive alternative to the reinforced concrete dump pocket that was originally designed for the project. The arrangement of the MSE wall is of an unusual configuration to meet a variety of operational and maintenance requirements. This paper outlines the selection process, design, and construction of the MSE wall.

Jan 1, 2009