Search Documents

By J. H. Schubert

Mintek has developed a level-control system, FloatStar, for use in flotation circuits. Instead of controlling levels separately in each unit, the controller monitors levels throughout the circuit. It can thus take account of the global effects of any control actions. A collaborative project between Mintek and Karee Platinum Mine has begun, looking at aspects of flotation control. Karee plant was chosen as the site for this work because of its good existing control infrastructure. As a first stage of the joint project FloatStar was installed. Analysis during installation and running of the FloatStar has illustrated how circuit design and measurement technology can affect process control. Severe interactions have been observed in the levels of adjacent banks. The effect of FloatStar on flotation performance was tested and an improvement in level control was observed. Similarly, a faster settling of the plant after start-ups was observed. Both the improved level control and faster start-ups lead to higher platinum recovery.

Jan 1, 1999

By J. M. Ortiz

Mineral resource evaluation requires defining geological domains that differentiate the types of mineralogy, alteration and lithology. Usual practice is to consider the domain boundaries as hard, i.e. data from across the boundaries are disregarded when estimating the grades within a given domain. This practice may hinder the quality of the estimates when a significant spatial correlation of the grades exists across the domain boundaries. In this paper, several geostatistical methodologies to handle soft geological boundaries are compared through a case study on a copper mine in Chile. The estimation methods considered are: ordinary kriging using hard boundaries between geological domains; ordinary kriging omitting the geological boundaries; traditional and standardized ordinary cokriging of the grades assayed in different domains; ordinary kriging within dilated geological domains, that is, incorporating samples from adjacent domains up to a given radius from the boundary of the domain being considered. The estimations are performed using a set of exploration data (drill hole samples) and are validated using a set of production data (blast hole samples collected for grade control). Results indicate that kriging with dilated domains performs better than ordinary kriging using hard boundaries or no boundaries and better than the ordinary cokriging approaches. It therefore appears as a simple alternative to global kriging (without considering the geological domains) and allows accounting for changes in the grade average, dispersion and spatial continuity with the geological characteristics of the deposit, via the use of grade variograms proper to each geological domain. The maximal distance for searching samples from adjacent domains should be chosen according to the spatial correlation of the grades across the domain boundaries, or via a cross-validation at an early stage of the mine or a jack-knife if production data are available. Keywords: Kriging; cokriging; soft boundaries; hard boundaries; geological control; geological domains.

Jan 1, 2006

By M. D. Lionnet

The Bafokeng Rasimone Platinum Mine (BRPM) is a joint venture between Rustenburg Platinum Mines Limited and Royal Bafokeng Resources (Pty) Ltd (Bafokeng). The mining lease has been granted over Boschkoppie 104JQ and is located approximately 10 km south of the Pilanesberg Alkaline Complex. The Merensky Reef, which constitutes the principal orebody, is geologically complex. A relationship between its geological variability and the associated mineralization has been established by defining a number of facies types. The Merensky Reef has been subdivided into seven distinct facies types: the pegmatoidal facies, contact facies, FW1 potholefacies, FW3 pothole facies, FW6 pothole facies, and FW7 pothole facies. The Merensky Reef, which does not form part of the potholed reef, has a large component of footwall mineralization. The pothole facies, in contrast, has mineralization located in the hangingwall. Statistical analysis of the facies types indicates that they are unique populations and hence need to be evaluated independently. The mining lease has distinct structural domains that have added additional complications to evaluation of the Merensky Reef. The Merensky facies on BRPM exhibit unique geological and statistical characteristics within well-defined structural blocks. Due to the extreme variability of the Merensky Reef on BRPM a unique approach has been developed, within Anglo Platinum, to evaluate the deposit. Mining cuts are defined and composited for the individual facies types, and then modelled individually by applying known geological controls. The resultant grade models are weighted based on statistical and local geological knowledge. The object of weighting the facies is to replicate the variability observed in the orebody. The introduction of stringent geological controls to the evaluation process has resulted in increased confidence in the in situ grades estimated as an input to the mine planning process.

Jan 1, 2007

By B. Friedrich

In a German governmental funded three-year research project, a closed loop recycling process for Nickel-Metalhydride-Batteries (NiMH) is under development. Today the discarded batteries are used in the steel industry as a cheap nickel source. Cobalt and rare earth (RE) are slagged and lost for reuse. The entire value of the metals in discarded Ni-MH is estimated to be 4?-4.5 ?/kg. Spent NiMH-batteries containing 36?42 per cent Ni, 3?4 per cent Co and 8?10 per cent rare rarth (Ce,La, Pr, Nd). The dismantled and processed NiMH-batteries are melted in a DC electric arc furnace producing a nickel-cobalt alloy and a slag phase highly enriched with RE-oxides. The key to success in this process is to find a suitable slag system, which ensures best separation of NiCo-alloy from the rare earth oxides and high concentration of RE in the slag. Different oxidic and halogenic slag systems are investigated in the melting process. So far a slag system based on 65per cent CaF2 and 35 per cent CaO delivers the best separation of the two phases and metal yields. A slag with a composition of 20?25 per cent La, 13-16 per cent Ce, 1.5?2.5 Pr, 4.5?6.5 per cent Nd is obtained and further treated to misch metal hydro-/electrometallurgically. The first results of the influence of rare earth oxides on the density of CaO-CaF2slag system are shown at 1600°C. Keywords: battery recycling, CaF2, CaO, rare earth oxides, slag characterization, density measurement

Jan 1, 2004

By D. Chetty

Process mineralogy forms an integral part of geometallurgy, with ore body characterisation being but one piece of the puzzle in optimising value derived from ore. This value is not only financial, but importantly speaks to sustainability from environmental and social standpoints. The reactive approach of traditional process mineralogy is increasingly being replaced by predictive methods in the geometallurgical sphere, for which mineralogical information must be timeously acquired on judiciously selected sample sets to understand ore variability and its impact on orebody processing. Such processes are not only metallurgical, but must incorporate mining and waste management protocols. Dwindling resources like water and energy also demand innovative approaches for lowering consumption and/or promoting recycling along the value chain. Addressing such challenges relies on appropriate characterisation of ore behaviour under different process regimes. Coupled with this, emerging characterisation tools are increasingly applied to understand the mineralogy of unconventionallypresented and difficult-to-process ores to meet societal and technology demands. Such tools are often accompanied by the generation of large, computationally intensive datasets, for which data management and storage are key requirements, particularly when deciphering temporal trends in ore and process variability. This paper will elaborate on these themes with examples that highlight the importance of process mineralogy throughout the minerals value chain. Keywords: Process mineralogy, ore characterisation, geometallurgy

Jan 1, 2020

By A. Chagnes

This paper presents a modelling tool that can be used to predict the behaviour of solvent extraction processes. In particular, this model allows calculating metal extraction efficiency as a function of pH, solvent flowrate, stripping flowrate and aqueous feed flowrate in the mixers-settlers. This model is applied to the recovery of cobalt from acidic chloride media by using CYANEX® 272 as extractant diluted in kerosene. Keywords: Cobalt, mixer-settler, modelling, solvent extraction

Jan 1, 2020

By W. Breytenbach

Traditionally, dithiocarbonates (xanthates) have been the preferred collectors for the flotation of platinum-bearing sulphides. However, collector development has led to trithiocarbonates (TTC), which have proven to be very effective bulk sulphide collectors. The interest in TTC flotation behaviour is currently focused on the interaction of these collectors with other collectors, specifically the dithicarbonates. Batch-flotation research has shown synergism to exist among dithiocarbonate, dithiophosphate and trithiocarbonate collectors. Increased sulphide recoveries, both for the first-minute and final concentrate, were realized using mixtures of these collectors relative to the standard.

Jan 1, 2003

By B. Samanta

This paper investigates the performance of the neural network technique in a placer deposit situated at the Nome district in Alaska. Initially a single neural network model was constructed to estimate the gold grade. However, at a later stage, an ensemble model consisting of multiple networks was also constructed via the Adaboost algorithm. The reason behind the use of the ensemble model of the Adaboost algorithm was to examine if the ensemble model provided superior performance to the single neural network. As indicated by other studies, Adaboost did not have a better performance than a single neural network in this specific application. This may be due to the high noise inherent in the gold data used in this project. Consequently R2 values of gold prediction are also poor for both the single and multiple networks.

Jan 1, 2005

By M. J. Nicol

Mr Vegter has analysed, in some depth, the approximations made in the treatment of the kinetic data presented in the original by ourselves (ref.1) and has come to the conclusion that ?under the experimental conditions used by Adams and Nicol (1986) the steady-state assumption was inaccurate?. We are acutely aware of the fact that the experimental method adopted does not permit the attainment of a true steady-state in the elution reactor. However, this does not eliminate the attainment of a pseudo steady-state by a suitable choice of the experimental parameters with the accompanying simplification of the analysis of the data with the aim of drawing the reader?s attention to the most important objective of the paper viz. the effect of various operating parameters on the rate of elution of gold.

Jan 1, 1997

By A. Bhattacherjee

The Shewhart [X]?and R charts are still the most popular control charts in use today for continuous monitoring of quality data. However, for these charts to function properly, the underlying assumption of normality and independence of data must be satisfied. When either independence and/or normality of data are not present, which is a common feature of ore quality data, an application of the conventional Shewhart [X]?and R charts may introduce false alarms in the analysis of the data. To address these issues, a guideline is proposed for construction of appropriate univariate and multivariate control charts for a variety of situations. A use of this guideline to a bauxite mine suggested the construction of special cause control chart for the analysis of individual variables namely, Al2O3% and SiO2%; whereas, the multivariate T2 chart based on residuals is proposed for the bivariate analysis of the variables. The case study clearly revealed that without considering the data correlation, one may be in a state of false impression about an out of control condition while using the Shewhart [X]?and R charts for univariate and the Hotelling T2chart for multivariate analysis. To compare the effectiveness of the control charts, specifically the Shewhart [X]?and the special cause control charts, a simulation study was conducted. It was found that the conventional Shewhart chart provided lower probability of coverage than the special cause control chart. It was also revealed that the quality specification of Al2O3% is met as the variation of Al2O3% is well within the specification limits; whereas, it is difficult to meet the quality specification of SiO2% on a regular basis.

Jan 1, 2002

By J. A. Kromhout, J. Trouw, A. A. Kamperman, M. Kick

Mould powders play an important role in the stability of the continuous casting process. The main functions of mould powders are to provide sufficient lubrication and to control the horizontal heat transfer. Because process control of thin slab casting is more stringent, it is generally assumed that mould powder properties become more critical as well. In 2000, the Direct Sheet Plant at Corus IJmuiden (DSP) was commissioned, incorporating a thin slab caster designed for casting speeds up to 6 m/min. During commissioning, several operational problems with mould powders were encountered i.e. insufficient liquid pool depth and the formation of rims/lumps. To investigate the operational mould powder problems, some of the mould powders were characterized using physical and mineralogical methods. The results were linked to operational experiences. It was concluded that for thin slab casting, a stable slag formation is obtained with a proper choice of free carbon and an even distribution of the carbon particles within the granules. The physical properties of mould powders are not as critical as expected when the additional mineralogical requirements are taken into account. Keywords: mould powder, characterization methods, thin slab casting.

Jan 1, 2004

By D. O’Connor, A. Pytlik, D. J. Corbett

The resistance of yielding rockbolts to multiple impact loads was tested by means of a drop hammer. The methodology was based on the ASTM D7401-08 standard as well as the requirements specified for rockbolts by Luossavaara-Kiirunavaara Aktiebolag (LKAB – a Swedish mining company) and the Safety In Mines Research Advisory Committee of South Africa (project number GAP 423). During the tests, the loading force and bolt elongation were measured with a sampling frequency of fs = 19.2 kHz. In order to analyse the phenomena involved, the tests were recorded using two independent high-speed video cameras (600 and 1000 frames per second) and one thermal camera (128 frames per second). The tests demonstrated that all the samples transferred double the gravitational potential energy of Ep = 50.85 kJ from the impact load of mass m = 2825 kg and impact velocity of v = 6.0 m/s without failure. Damage to the bolt-resin contact in the upper anchoring zone of the bolt in the steel tube occurred after subsequent impacts. As a result, the macro-deformed bolt exhibits additional yield, and its operation following the shearing of the resin bond is similar to that of a ‘cone bolt’. Only one test resulted in damage to the threaded bolt rod-nut coupling, during the fourth impact; however, no damage to the bolt-resin contact zone was observed.

Nov 6, 2023

By S. Dalton

The use of coal for power generation is being questioned in many developed countries, as a result of ever-tightening environmental restrictions and concerns about the potential impact of CO2emissions on climate. Coal will continue to be the fuel of choice for new power plants for many developing countries with large percentages of the world?s population, because of its relatively low cost and broad availability. Even in many of the developed countries that are under pressure, coal will continue to fuel large percentages of power due to the installed base. Using coal efficiently and in an environmentally responsible manner will be a challenge for technology and politics in this new century, with the politics played out on the world stage. Coal use will vary in the next few decades, including short-term changes such as the use of more diverse coals and the increased use of efficient ultra-supercritical boilers to longer term ?refining? of coal to produce a range of energy and chemical outputs. This paper outlines EPRI?s Global Coal Initiative aimed at needed developments and demonstrations that support the long-term vision of environmentally sound and economical coal use for power generation, and discusses some of the forces that are driving this development effort.

Jan 1, 2001

The typical reactions which the reductants undergo during ferroalloy production are reviewed, and identified as reaction with CO2 and with SiO, and dissolution in metal. Available reactivity tests for these three reactions are reviewed. It is proposed that it is worthwhile considering dissolution kinetics as a reactivity parameter. Greater crystallinity of the reductant decreases CO2 and SiO reactivity, but increases dissolution rates.

Jan 1, 2002

By J. Kirsch

Keywords: Pyrometallurgy, pneumatic transport, pneumatic transport Dense-phase pneumatic injection has begun to replace more traditional furnace-feeding systems. The paper describes the technology as it is applied to processes where the back pressure at the point of injection is greater than 50 kPaG. It reviews earlier systems of injection and more recent developments that address concerns for instantaneous control in modern smelters. The new technologies fall into two groups, (1) modified pressure-difference control (sub-divided into simple and complex) and (2) mechanical-feeder-based control. Features of current injection systems include feed splitting in two forms, passive and active, and co-current injection.

Jan 1, 2006

By R. P. H. Willis

Uranium is back on the radar. Uranium has always been a controversial metal, from its role in the arms race to its claim to be the only viable alternative to fossil fuel. This paper will cover its properties and use, its occurrence and production in South Africa, the current market drivers and its future role as a primary energy fuel. It will highlight the difference between uranium used to make a bomb and uranium used in a power station. The recent significant uranium price rise will be put into context of the market drivers including geopolitical issues. Planned expansions in nuclear power station capacity will be reviewed, as will new mine production. Future demand will also be speculated on.

Jan 1, 2006

By Y. Mao, D. Xie

The viscosity of TiO2-containing blast furnace slags may increase rapidly (commonly referred to as thickening) under strong reducing conditions in the blast furnace. To elucidate the mechanisms for slag thickening, measurements have been made of changes in the composition and rheological properties of TiO2-CaO-SiO2-Al2O3-MgO slags during the reduction process. The slag composition covered the range of 17–33 wt% TiO2, 9–19% Al2O3, 8–16% MgO and theCaO/SiO2from 0.8 to 1.4. The viscosities were measured using the rotating cylinder method at temperatures up to 1550ºC and the fusibility temperatures were determined from ‘breaks’ in the viscosity-temperature curves. The reduction of the slag was carried out in graphite crucibles at1500ºC for 2–6 hours The rheological properties of the slags during reduction were predominantly influenced by the slag basicity (CaO/SiO2), and the effect of other components depended largely on basic or acidic behaviour of the oxide. The reduction of TiO2in the slag by carbon was initially fast to formTi2O3, followed by further reduction to TiO and TiC. Correspondingly, the viscosity showed initially a slight decrease, followed by a gradual and then rapid increase. The thickening was found to be accelerated by an increase in TiO2content and a decrease in the CaO/SiO2in the slag. In addition to the existence of 1~3 wt% TiC, the thickened slags also had a significant amount of TiO (3~7 wt%), suggesting that TiO may play an important role in the ‘thickening phenomena’ ,possibly by forming solid solutions with TiC to significantly increase the number of solid particles in the heterogeneous slag. Keywords: TiO2slags, viscosity

Jan 1, 2004

By L. Li

The performance of microemulsified diesel and conventional diesel collectors in coal flotation was compared by flotation indicators, including combustible recovery, ash content of the clean coal, and the flotation index. An efficient separation with lower dosage was obtained using the microemulsified diesel collector. Under optimum separation conditions, the microemulsion consumption was 100 g/t less compared with diesel. The saving in diesel consumption using the microemulsion reached about 70%, disregarding the consumption of the surfactant and cosurfactant. Frothing tests showed that the frother dosage was decreased by using the microemulsion collector, because of the surfactant and cosurfactant added during preparation. The microemulsified diesel collector is superior to the conventional diesel collector in terms of diesel consumption and separation efficiency, but the selectivity requires further improvement. Keywords froth flotation, microemulsified collector, coal.

Nov 1, 2013

This paper reviews ore pass practice in some Canadian mines in Quebec and Ontario. In particular it reviews ore pass configuration, flow control mechanisms and monitoring practice. A review of the type of problems encountered and the tools to restore flow is also presented.

Jan 1, 2005

The results of a series of physical model studies of the stability of jointed rock slopes carried out some years ago are described. These models were tested under centrifugal loading. Four ?geological? structures were tested; all had the same joint orientations and strengths, but the relative spacing of the joints was different. The results showed that the mechanisms of failure of the slopes varied for the different models, and the gravitational loads at which failure developed also varied. The following conclusions are drawn from the results of the physical model tests: ?the mechanism of slope failure is by progressive deformations throughout the slope ?the ratio of the spacings between the different sets of discontinuities exerts considerable influence on the slope failure ?in the models tested, the intact material strength had no noticeable influence on the stability of the jointed rock slopes(note that for hard rock, similitude conditions indicate a prototype slope height of 300 to 400 m, and therefore intact rock failure might not be expected under simple gravity conditions, i.e. no tectonic stresses) ?rock slope failures are three-dimensional and in general are not amenable to two-dimensional simplification ?knowledge of the orientations of discontinuities in the slopes does not allow prediction of a unique failure surface, nor of a volume of failure. The volume of failure is determined to a large extent by the plan configuration of the slope.

Jan 1, 2006