Search Documents

By E. Molobi

"Studs are rods threaded on both ends and are used as mechanical fasteners for two or more components. Stud finds usage in industries such as automotive, construction and aviation. The advantage of studs is that they allow for disassembly of components during maintenance. Studs are continuously subjected to both tensile and shear stresses, depending on the application, therefore they should be manufactured from suitable materials that are capable of withstanding all these external forces. Studs are sometimes manufactured from re-sulphurized steel due to its improved machinability; however, there is a certain limit on the amount of sulphur, above which failure may occur. Premature failure of studs has been a common problem, but failed studs are commonly replaced with new ones without conducting failure investigations. The present work investigates the premature failure of two re-sulphurized steel studs used on a rocker arm assembly and recommends alternative materials. The investigation was carried out by conducting visual examination, microstructural analysis, hardness measurements, chemical analysis and a detailed scanning electron microscopy (SEM) investigation on the fracture surface.IntroductionTwo rocker arm studs used on a 16-cylinder diesel locomotive engine failed prematurely after being in service for less than 5 months. The rocker arm studs had a life-cycle of 5 years. The studs were manufactured from resulphurized steel. The paper aims to establish whether re-sulphurized steel is applicable for the manufacture of studs in the automotive industry.BackgroundLocomotives are classified as either electric or fuel-powered. Diesel locomotives are an example of fuel-powered locomotives. This type of locomotive uses a diesel engine as a means for propulsion. An engine converts chemical energy into mechanical energy required for traction. In an internal combustion engine a rocker arm is an oscillating lever that conveys radial movement from the cam lobe into linear movement to open and close poppet valves of cylinders (Husain and Sheikh, 2013). The rocker arms are secured on to the cylinder head by rocker arm studs."

Jan 1, 2016

By Luis Rudolphy, Pekka Tähkiö

"Flotation plant design, construction and start-up can be challenging tasks, because multiple factors and disciplines have to be combined in an efficient manner, in order to execute a project that meets the technical, financial and timeframe expectations. Key considerations that need to be addressed when designing a flotation plant are process requirements, equipment integrability, automation, and up- and downstream processes/designs. Furthermore, several other lifecycle factors need to be considered, such as servicing and maintainability, operational costs, future expansions and decommissioning, among others. To address these challenges, Outotec has developed a new approach to designing flotation plants that targets eliminating most of the inherent risks that can be found in these types of projects. The new Outotec® plant is a fully modular approach in which the above-mentioned challenges have been taken into consideration in the design phase. As a result, the cPlant concept can give several benefits for new and experienced companies involved in the minerals processing business, such as lower risk investments, fast and cost-efficient flotation plant delivery, faster ramp-up period, easy plant expansions, fully automated processes and operation and maintenance ease. As well, dismantling and transportation of the cPlant to a new location is easy and fast, hence the new cPlant concept makes possible to exploit small, short-lifespan ore deposits and also retreat old tailings ponds that might contain valuable minerals and where the ore quantities are limited. Furthermore, cPlant is easily implemented for brownfields and temporary expansions during bigger expansions."

Jan 1, 2015

By E. J. Magri, A. Couble

Kriging estimates of geological resources are sometimes conditionally biased because the kriging plan contains too few samples. This may be done purposely in order to match the variance of the estimates to the true block dispersion variance. This work aims at evaluating the influence of conditional bias over the ultimate optimum pit design in relation to its shape, size and NPV (Net Present Value of profits). It has been restricted to two real case studies: a ‘carrot shaped’ gold porphyry in northern Greece and a manto-typeexotic copper deposit located in northern Chile. The methodology applied to each deposit consisted of generating a ‘real block model’ and four resource estimates by the use of conditional simulation and the application of four different kriging plans to the drillhole databases respectively. The estimation models vary in smoothness and conditional bias. Ultimate optimum pits were determined for the ‘real’ and the four different kriging models. Pit comparisons lead to the following conclusions: •In the worst case, conditional bias overestimated the project's NPV by 32% and 5% for the gold and copper deposits respectively. •The overestimation of high grades is more relevant than the underestimation of low grades. This resulted in a tonnage over-extraction of 148% and 1% for the gold and copper deposit respectively. This difference was attributable to the vastly different geometry of the deposits. •The smoothing effect of kriging, without or very little conditional bias, produced open pits that were different to the ‘true’ (ideal) ones and furthermore, underestimated the project's NPV by 10% and 6% for the gold and the copper deposits respectively. •Other factors that influence the optimum open pit design and to some extent control the effect of conditional bias are: the cut-off grade, the orebody geometry and distribution of grades within it and the amount of over-burden. Keywords: conditional bias, ultimate pit design

Jan 1, 2003

By Q. G. Reynolds

The problem of direct-current plasma arc behaviour, interaction, and dynamics is considered in the context of metallurgical DC arc furnace applications. Particular attention is paid to the transient flow behaviour of arc systems. A mathematical formulation of the physics used to describe the arc system is presented, and includes the spatial and temporal evolution of fluid flow, heat transfer, and electromagnetism. Based on this formulation, a numerical model is developed using a finite difference approach on a regular cartesian grid in both two and three dimensions, with a special focus on robust stability, high resolution modelling, and high performance. A collection of results produced using the numerical model to study pilot plant-scale furnaces is then presented. These address a range of process and design variables and their effect on the numerical model?s results. Where possible, the qualitative behaviour of the model is compared to available experimental data. A number of novel effects and phenomena are seen in the dynamic behaviour of the DC plasma arc model for both single and multiple arc systems, which may lead to improved understanding, control, and manipulation of such systems where they occur in industrial applications. Keywords Pyrometallurgy, direct-current furnace, plasma arc, modelling.

Jan 1, 2010

By R. Hewer

Transition metals have been widely used in medicine throughout history. The medicinal use of metals extends back to the earliest recorded history when the Chinese used gold as treatment for a variety of ailments. The ancient Egyptians used copper to sterilize water and mercury was reportedly used by Hippocrates in 400BC. Thereafter, numerous other metals have been used as treatment throughout the centuries. For example, zinc sulphate was used as an emetic in the 17th century and zinc oxide was used to treat epilepsy in the 18th century. This use of metals, and numerous other instances, which have been well described in Sneader 2008,1 make for interesting reading but largely occurred prior to the advent of rigorous scientific method. Therefore, although there are exemptions, most therapeutic applications of metals prior to the modern age lack scientific grounding and have been found to be mostly ineffective. Of more relevance are metal-based medicines approved by regulatory bodies (i.e. Food and Drug Administration; FDA) that are in current use as therapeutic drugs. There are presently a large number of metal-based drugs that are approved for use by the FDA ranging from over the counter medicines, such as bismuth subsalicylate for gastrointestinal problems, to prescription drugs such as lithium carbonate for the treatment of manic depression. The list of metal-based medicines approved by the FDA not only incorporates base metals but also includes precious metals. Platinum complexes have been found to be potently active against several different types of cancers while gold complexes have shown application as treatment for rheumatoid arthritis (RA). With the well-established foundation that exists for metal-based medicines, it is imperative to continue exploration into new therapeutic areas. The precious metals; gold, ruthenium and platinum, continue to attract scientific interest in the field of biomedicine and have been widely researched. Scientific studies conducted on gold complexes have demonstrated the potential of this metal for the treatment of HIV/AIDS, cancer and malaria. These diseases are also specific health concerns for developing nations; countries where disease has devastating impact. Within South Africa alone, an estimated 5.7 million people are infected with HIV/AIDS,2 approximately 7 000 new cases of malaria are reported annually, and it is projected that 1 in 4 persons will develop cancer. Continuous development of therapeutic drugs to combat these diseases is therefore apriority, and the exploration of gold-based compounds for this purpose is warranted.

Jan 1, 2009

"Pressure leaching is an option for copper recovery from chalcopyrite. Leaching takes place at high temperatures and pressures in the presence of an oxidizing agent. This work shows how the performance of pressure leaching circuits may be improved by optimizing the configuration of autoclaves and the heat removal method. The objective was achieved by creating an autoclave model that combines mass balances, energy balances, and population balances. A base case circuit consisting of a single autoclave was chosen, and this base case was compared with options for increasing capacity by adding more autoclaves to the circuit. These capacity increase options include circuits in which the additional autoclave is added in parallel, in series, and in series with thickening between the two autoclaves. The copper extraction, productivity, and cooling requirements for these options are compared. The series circuit with interstage thickening has the highest extraction and productivity; however, the cooling duty in the first autoclave is high. In addition to comparing circuit options, three options for heat removal were investigated: cooling coils, quench water, and flash recycling. The flash recycle option results in the highest copper extraction, and the quench water option the lowest copper extraction. IntroductionBackgroundCopper sulphide ores and concentrates containing chalcopyrite are typically hard to leach under atmospheric conditions. Smelting of these ores may also be a challenge, due to the inability of smelting processes to handle low-grade ores, as well as impurities such as arsenic and antimony. Alternative hydrometallurgical routes to treating chalcopyrite are therefore required. One option is pressure leaching, which is the focus of this work.In the pressure leaching process, sulphide ores and concentrates are leached in autoclaves at temperatures of 200 to 220°C and a pressure of about 3000 kPa (Schlesinger et al., 2011). An oxidizing agent, usually oxygen, is required to oxidize sulphide ions to sulphate ions. The oxidation of sulphur to sulphate is exothermic; consequently, a method of heat removal is necessary in order to maintain the temperature in the autoclave."

Jan 1, 2016

By M. Kumral

One of the most significant elements in solving the co-kriging equations is the matrix solver. In this paper, the singular value decomposition (SVD) as an equation solver is proposed to solve the co-kriging matrices. Given that other equation solvers have various drawbacks, the SVD presents an alternative for solving the co-kriging matrices. The SVD is briefly discussed, and its performance is compared with the banded Gaussian elimination that is most frequently used in co-kriging matrices by means of case studies. In spite of the increase in the memory requirement, the SVD yields better results.

Jan 1, 2012

By S. C. Essack

"Tenova Pyromet has designed a slag flow control valve that throttles the flow of slag in order to control the tapping rate. In addition, the valve has proved to be a reliable tool for closing the furnace during normal operation as well as emergency conditions. The valve makes use of a water-cooled copper element that is hydraulically operated and attached directly to the slag tap-hole. The equipment is compact, simple to maintain, and cost-effective to purchase and install. It can be retrofitted to most existing slag tapholes with minimal modifications.During the development phase, finite element method (FEM) and computational fluid dynamics (CFD) software was extensively used to model predicted operating conditions and to optimize the design. By using CFD, it was possible to understand the flow patterns inside the copper and to optimize these to improve overall performance.The slag valve was installed and commissioned in 2011/2012 on a 12 MW furnace as part of a new mineral wool plant in the USA. It has performed well since its installation despite operating under conditions in excess of the original design criteria. During the first 6 months of operation it quickly became the preferred method of closing the furnace, although the design intent was for occasional use during emergency shutdown conditions only. Since replacing the mudgun as the main method of closing the tap-hole, a few minor changes have been made to the installation in order to cope with the increased heat load and much higher frequency of use."

Jan 1, 2014

By H. Edinger

China?s engagement with the African continent has increased impressively in the past decade. Even though China is not the African continent?s largest stakeholder, the rapidly increasing engagement is evident in the huge number of Chinese migrants that have come to Africa in the wake of unprecedented trade and investment levels, as well as in increasing diplomatic and political interactions, which has taken most other commercial partners by surprise. All but four countries in Africa have adopted the ?One China?1 policy stance; and in so doing opened the door for new or strengthened commercial dealings with China, including increasing investments into Africa?s extractive industries. This has been particularly evident since the turn of the century, with a clear shift in China?s policy towards Africa elevating the continent in China?s foreign policy objectives. As such, Africa has become a strategic focus2 for Chinese outward bound and internationalizing companies, especially in the extractive industries. This planned shift in focus is based largely on geo-strategic and commercial needs and interests, rather than previous ideological ones.3

Jan 1, 2011

By M. J. Kanda

"The design of rock slopes in the planning and operation of open pit mines and for road and rail cuttings requires the evaluation of their stability. This is commonly done using two well-established methods – limit equilibrium and numerical modelling. The research described in this paper compares the outputs of analyses using these two methods with regard to factor of safety and probability of failure, taking into account technical factors associated with each method and other factors such as material parameters and their variabilities. Results show that technical factors such as number of slices and slip circles, number and type of finite elements, and the stress reduction factor can all affect the results of stability analyses. Factors not taken into account in limit equilibrium analyses, such as dilation, in situ stress, and locked-in stresses can affect the outputs significantly. The research has focused particularly on the predicted location of the failure surface, the resulting volume of failure and, most significantly dependent on this volume, the predicted risk associated with slope failure. The results presented show that there is good agreement between the outputs of the two methods regarding factor of safety and probability of failure. However, the same is not the case with regard to volume of failure and hence risk, which can be very dependent on the methods of analysis and their input parameters. The research is not exhaustive, and there are many other factors that could affect the results of slope stability analyses that were not investigated. Some such factors are mentioned in the paper.IntroductionThe design of rock slopes in the planning and operation of open pit mines and for road and rail cuttings requires the evaluation of their stability. The traditional method of stability analysis used limit equilibrium (LE) methods, and this approach continues to be used. Numerical modelling (NM) packages are now also commonly used in slope stability analyses. The outputs from these analyses provide the factor of safety (FOS) and probability of failure (POF) of the slope. Since the capabilities of the two approaches are different, there can be some variations in FOS and POF outputs and in the predicted location of the failure surface. These variations can affect the predicted volume of failure, and this could in turn have a significant effect on the risk associated with the potential failure (Read and Stacey, 2009). Researchers such as Chiwaye and Stacey (2010) have found that LE analyses underestimate the predicted failure volume, unlike NM methods."

Jan 1, 2016

By L. Lorig

"Two types of extreme event, earthquakes and rainfall, potentially affect open pit slope stability. In the case of earthquakes, there are rather well-developed analysis procedures and acceptability criteria. The analysis procedures relate mainly to selection of the dynamic loading either through design earthquakes and/or pseudo-static seismic coefficients. The acceptance criteria are typically expressed in terms of a minimum safety factor in pseudo-static analyses. The acceptance criteria are often promulgated by governments despite the fact that no open pit slope has ever been adversely affected by an earthquake. This paper explains why open pit slopes are seemingly more resistant to dynamic loads than natural landforms, which can experience catastrophic landslides.Extreme rainfall events are much more likely to cause open pit slope problems than earthquakes. Two types of problem are common – slope erosion and slope instability. Slope erosion is often mitigated by appropriate surface water controls. Slope instability due to elevated transient water pressures is more difficult to mitigate. Analysis procedures and acceptability criteria are rare. This paper will discuss the mechanisms for rainfall-induced slope instability, as well as analysis methods. Examples will be discussed and analysis methods are proposed. IntroductionTwo types of extreme event, earthquakes and rainfall, potentially affect open pit slope stability. In the case of earthquakes, there are rather well-developed analysis procedures and acceptability criteria. The analysis procedures relate mainly to selection of the dynamic loading either through design earthquakes and/or pseudo-static seismic coefficients. The acceptance criteria are typically expressed in terms of a minimum safety factor in pseudostatic analyses. The acceptance criteria are often promulgated by governments (e.g., Peru, Chile) despite the fact that no open pit slope has ever been adversely affected by an earthquake. This paper explains why open pit slopes are seemingly more resistant to dynamic loads than natural landforms, which can experience catastrophic landslides.Extreme rainfall events are much more likely to cause open pit slope problems when compared to earthquakes. Two types of problems are common – slope erosion and slope instability. Slope erosion is often mitigated by appropriate surface water controls. Slope instability due to elevated transient water pressures is more difficult to mitigate. Analysis procedures and acceptability criteria are rare, but do exist. In Peru, for example, slopes are required by law to be designed for a 100-year storm."

Jan 1, 2016

By J. C. R. van Schoor

In this study the applicability of a batch press to predict the energy consumption and particle size distributions for medium-pressure roller presses was investigated. The relationships between energy consumption, feed size and product size are discussed with reference to Hukki?s interpretation of Bond?s and Rittinger?s laws, as well as the particle size parameter used. It was found that the comminution laws have limited utility for the characterization of the performance of the medium-pressure roller crushers or the batch press used, and also depend on the particle size distribution indicator used. It was also found that the batch press is not a suitable simulator for medium-pressure roller mills as it was notable to predict the energy requirements, or to predict the size distributions that would be obtained for the ores evaluated.

Jan 1, 2012

By L. Gunnewiek

An advanced real-time monitoring system called the tapblock diagnostic system (TDS) has been developed. The purpose of the TDS is to help furnace operators manage the safe operation and economical maintenance of furnace tapblocks. This system is an evolution of the current practice of using historical records and operator interpretation to assess the ?health? of a tapblock. The main parameters affecting tapblock health are heat removal capacity and refractory wear, and these are currently difficult to assess in situ except in a global way. By using monitored and operating data together with predictive numerical modelling and multivariate statistical methods, real-time tapblock performance is assessed relative to expected performance. A state indicator in the form of a green, yellow, and red light is used by furnace operators to monitor the tapblock performance and health status during operation. Access to historical operating data and the provision of diagnostic functions allow for probable health degradation events to be deeply investigated. A recent opportunity to evaluate the actual performance of a first generation TDS installed in the KIVCET furnace at Teck Cominco?s Trail Operations showed that a reasonable estimate of tapblock health was made. However, the evaluation also found that some areas of refractory wear were missed, and a new mechanism affecting refractory wear was discovered that was not previously known. This has reinforced the belief that there is a need to develop improved methods of monitoring so that data used to define the health of the tapblock is more comprehensive and accurate.

Jan 1, 2008

The key functions of project evaluation are to assess potential profitability and to develop an effective operational design. For mining projects, design aspects include mining methodology, ore treatment methodology and production rates. All of these characteristics impact on project economics and overall value. Resource models, which form the ultimate basis of project evaluation, typically consist of tonnes above cut-off, grade above cut-off and the spatial distribution (connectivity) of tonnes/grade above cut-off, for one or more variables. Dilution, ore loss and metallurgical recovery are all modifying factors applied to the resource model during evaluation and determination of profitability. A key issue is: how is the value determined? In addition to traditional combination of in situ tonnes/grade, the following merit serious consideration: the concentration of deleterious elements, throughput rates, mining/processing costs and - importantly - metallurgical recovery. Geometallurgy is an emerging field targeted at integrating these issues by identifying either direct measures or proxies for throughput (hardness, grindability), recovery (liberation, mineral shape/texture, etc) and concentrate quality from easily collected macro-, meso- and microscopic data. These 'geometallurgical variables' drive project costs and revenues in a fundamental way. For geometallurgical characterisation to have a real impact on business design, it must enable improved mine planning. When creating spatial estimates for such variables, it is preferable to find proxies that can be measured as close to the intact rock mass as possible. However, spatial estimation of proxies for geometallurgical properties and responses is complex and requires special consideration. Unlike grades, both proxies and absolute measures of geometallurgical variables are not necessarily linear or additive and therefore require very careful geostatistical consideration. In some cases, models must predict extreme values of geometallurgical attributes rather than averages. Incorrect characterisation of metallurgical recovery/throughput can (and has) led to misspecification of the scale of projects, and thus can be seriously value destructive. Aspects of geometallurgy have long been important in iron, bauxite, manganese and coal deposits and are increasingly on the radar for base and precious metal miners. However, as more metallurgically complex deposits are developed and mining of large-scale, low-grade deposits becomes more commonplace, the importance of characterising the metallurgical response in order to generate properly optimised projects will rapidly increase. It is possible that in many `traditional' (ie grades and tonnes) reserve models, the variables that drive the project are missing!

Jan 1, 2007

By Z-P. Song, Z-B. Jiang, A-N. Jiang

"In deep excavations under conditions of high ground stress, even hard rock undergoes creep and other time-dependent effects that may result in instability. This study involves an analysis of the typical damage to the surrounding rock in the deep tunnels of the Jinchuan nickel mine in China. In order to understand the creep mechanism, triaxial creep laboratory tests were conducted under high stress. The creep characteristic curves and the Nishihara model parameters of typical rock were obtained from these tests. The numerical simulations, with which the creep model is developed, were performed using Flac3D. The creep model parameters were back-analysed on the basis of field monitoring data. Finally, appropriate support schemes for deep tunnels are suggested. The creep deformation of rock increases with time and axial load. At the same load level, the creep deformation of unloading is greater than that of loading. The simulated deformations of the surrounding rock are coincident with those from in situ monitoring, indicating the applicability of the presented rock creep model in situations of high ground stress. The results constitute a reference for support design in deep mining tunnels.IntroductionThe excavation of underground caverns can alter the natural stress field of the surrounding rock. In deep engineering projects under conditions of high ground stress, even hard rock shows obvious creep properties and time effects (Yao, 2005; Liu, 1994). The time effect of excavation not only causes decompression of the floor and increases sidewall stress, but also leads to stress concentration at the corners of the excavation, which influences the stability of the surrounding rock in a very complex manner.Many researchers have studied the creep properties of rock. ‘Griggs (1939) showed that creep occurs in sandstone, shale, and silty sandstone rock under the load of 12.5%–80% of the failure load.’ Subsequently, much research has been published on rock creep tests, including the uniaxial compressive creep test, the triaxial compressive creep test, the discontinuity rock shearing test, and field tests (Wawersik, 1974; Amadei et al., 1980; Okubo et al., 1991; Jin et al.,1995). A rheological model is used to describe the complex rheological deformation of material. This model is based on various fundamental parameters including rock elasticity, plasticity, and viscous properties, which can be combined into a constitutive model to reflect the rheological properties of various types of rocks. Wang et al. (2014) studied the creep– damage–rupture characteristics of rock salt by applying a creep-damage model. Munson (1997) developed a multi-mechanism constitutive model of creep of polycrystalline rock salt based on steady-state creep and modified it to incorporate transient creep through work hardening and recovery. An elasto-viscoplastic approach was developed to simulate the timedependent nature of the fracture zone (Malan, 1999). Rheological models were proposed to understand the collapse of iron ore mines in Lorraine by Dragan et al. (2003)."

Jan 1, 2016

By J. Bai, C. Zang, W. Yuan, L. Zhuang

"This study evaluates the efficiency of using mechanochemical reduction to assist the extraction of zinc from zinc ferrites by alkaline leaching. The transition of zinc ferrite into a metastable state after mechanochemical reduction with metallic iron contributes to the ready dissolution of zinc from the activated zinc ferrites in alkaline solution. Zinc ferrites were mechanochemically reduced under conditions of Fe:ZnFe2O4 mole ratio of 2:1, using 5 mm diameter stainless steel balls as the activation medium at a mass ratio of balls to raw materials of 25:1. Subsequent leaching in 6 mol/L NaOH solution at 90°C resulted in more than 70% Zn extraction. These results may be used to further develop a hydrometallurgical process for recovering zinc from zinc ferrites in alkaline solution.IntroductionZinc is an important nonferrous metal required for various applications in batteries, solder, dielectric materials, and piezoelectric materials. High-grade, easily concentrated ores are becoming scarcer: to meet world demands for zinc, it is necessary to develop economical and environmentally safe metallurgical technologies that use secondary materials such as leach residues of roasted zinc concentrates and electric arc furnace dusts. The zinc in the majority of these wastes occurs in the form of zinc ferrite (franklinite, ZnFe2O4), which is very stable and insoluble in most acidic and alkaline solutions (Langova and Matysek, 2009; Youcai and Stanforth, 2000).Several pyrometallurgical and hydrometallurgical processes (Jankovi et al., 2014; Langova and Matysek, 2010; Morcali et al., 2012; Shawabkeh, 2010) have been proposed for the treatment of zinc ferrites. Pyrometallurgical methods are costly owing to high energy consumption and their emissions of toxic gases are considered an environmental problem; hydrometallurgical methods are preferred for process economy and environmental reasons (Copur et al., 2004)."

Jan 1, 2016

By K. Harlow

"Zircon is a naturally occurring radioactive material (NORM) and as such is subject to a variety of regulations around the world. The regulatory processes and their implementation are summarized and the key issues affecting zircon and zirconia highlighted. Having absorbed the activities of the former Zircon Minerals Committee, the strategy of the Zircon Industry Association (ZIA) is to be the ‘go-to place’ for information on these matters, and its activities in the NORM space are described. Chemical industry regulations such as REACH are spreading around the world, and the paper provides an update of their status in the key jurisdictions. As mineral sands are transported to market in oceangoing vessels, they are subject to the regulations of the International Maritime Organization, which are summarized in the paper. IntroductionFrom a global perspective, zircon is generally not found in high concentrations other than in placer and dune deposits where it has been deposited along with other heavy minerals such as ilmenite, rutile, and monazite. Such deposits have been sorted and concentrated over geological time by the action of tides, waves, and wind to form concentrated deposits of heavy minerals along old coastlines and in river beds and deltas. Consequently, zircon is mostly found in association with the principal titanium minerals ilmenite and rutile. These secondary concentrations in placer deposits provide the commercial sources of zircon.All geological materials contain natural radioactivity, although the term NORM (naturally occurring radioactive material) is mostly used for minerals and other materials with above-average uranium and thorium concentrations. Importantly, the radioactive nature of zircon has not changed, but the way in which radioactivity is viewed by regulators has, affecting the zircon industry throughout the value chain."

Jan 1, 2017

By L. M. Tavares, T. M. Campos, P. M. Faria, R. M. Carvalho

Recent advances in mechanistic ball mill modelling are expected to allow for more accurate predictions that overcome the well-known limitations of phenomenological approaches, including their inability to predict the effect of liner geometry and their wear, in grinding. Although able to describe continuous operation, the UFRJ model of ball mills has only been validated in the past in mills that operate in batch mode, either in laboratory or pilot scale. The present work demonstrates the application of the mechanistic UFRJ ball mill model to predict fine grinding of iron ore in a pelletising plant in Brazil, the first application of such a mechanistic modelling in continuous mode. It shows that the model provides accurate descriptions of flows after iterations in a closed-circuit with hydrocyclones. Keywords: Ball mill, iron ore, grinding, modelling, particle breakage

Jan 1, 2020

By N. C. Joughin

A simplified economic model is derived for the financial return from a new gold mining project. The model is used to analyze the effects of changes in the mining rate, capital costs, working costs, value of the reef and the stoping width. The most effective avenues for improving the return from a new project are indicated. It is shown that those technological innovations which would improve the return significantly, and therefore make it possible to open more mines, are the use of smaller mines, means for improving the mining rate to capital costs ratio for smaller mines, planning and control of mines by computer simulation, an improved mine valuation procedure and means for mining at a decreased stope tramming width.

Jan 1, 2014

By K. B. Owusu, W. Skinner, R. K. Asamoah, J. Karageorgos, M. Zanin, C. Greet

High Pressure Grinding Rolls (HPGR) are mostly used prior to pelletising processes to increase the specific surface area (SSA) of iron ore concentrate. For expressing SSA, the Blaine index is utilised as one of the most important dimensional properties of iron ore pellet feed. ISO 21283 is a standard test method that explains the manual of Blaine air-permeability apparatus for determination of this parameter. In this standard, the disaggregation method is based on passing the minus of 1 mm samples from the 0.150 mm sieve. The disaggregation process has an effective role on the results of Blaine airpermeability test especially for regrinding HPGR products. In this research, firstly the Blaine index of samples was measured without disaggregation. Following this, disaggregation was done by passing the minus of 1 mm samples through three sieves with different dimensions, 0.150, 0.090 and 0.045 mm, separately, and the Blaine index was calculated for each one. Finally, lab-mill with rubber balls, called Jar mill, was investigated as another option. Screen analysis and image analysis with SEM were performed to evaluate the effects of the sample's disaggregation on the size distribution and agglomeration of samples. The results showed that the disaggregation method with sieve size 0.150 mm, according to ISO 21283, was not applicable for HPGR products because the particles were still stuck together. In addition, the disaggregation method with the sieve size 0.045 mm or with Jar mill offered reasonable results. Keywords: Disaggregation, Blaine index, specific surface area, regrinding HPGR, ISO 21283, Jar mill

Jan 1, 2020