Search Documents

By Will H. Coghill

The scope of this paper is such that it was deemed advisable to group the contents into several main sections. They are: Section 1. Geography and Geology. Section II. Historical Review. (a) Mining and Smelting in Alabama. (b) Milling. (c) Summary of Milling Research. These two sections are primarily a bibliography and summary of the research on the Birmingham Red Mountain ores up to the middle 1040's. Section III. Status of the Birmingham Iron Industry. This sect ion points out the extent to which the findings of the iron-ore research have been applied on a commercial scale. Also, a very brief description of the dependent and allied industries is included. The value of the Birmingham iron ore is greatly enhanced by the proximity of coal and dolomite. Thus the coal and coke industry and the dolomite industry are closely allied with and to a large extent dependent upon the possibilities of economic utilization of the Red Mountain iron ores. Section IV. Beneficiation Investigations of the Red Mountain Iron Ores. This is a record of the most recent, hitherto unpublished work of the Southern Experiment Station of the Federal Bureau of Mines, Tuscaloosa, Ala., on the chemical and physical composition not only of the Big seam but of most of the iron-bearing rock strata of Red Mountain.

Jan 1, 1946

By R. L. Grant

[p(,ton~to'rs 'ar-IV uscG.. to explode 9crnli .... sible c}:plosivcs, dynamites, or other hiGh uxplosives. This ?,...!xplosion or detr)nation is brought about by th\.:J energy which i liberated as a cOl":"Lb' nation of concusBion and heat wl1en the ? detonator is fired. 'm Ot:18t? I'l(jrds~ liThe detonator is the key VI: ich unlocks the enerGY of a llgh? explosIve""? (8) :1/. Being sensitive nd latently dangerous, detonators ITl.ust lTIeet t\V0 primary requirerDentr: They must be ..;.afe to handle and IT. list? detonate' when (l,esired, the ... eby iIr.parting deton:l.tion to the explo8ivc cJ.1Cire-e.]

Jan 1, 1941

By C. W. Elder

"INTRODUCTION This report describes a method of horizontal drilling in an oil-producing formation underlying a 400-acre, approximately square plot of land in the Franklin Heavy oil field in Sugar Creek Township, Venango County, Pa. The method, which was developed on two previous projects in Ohio, 3/ consists of sinking a shaft to the bottom of a shallow oil sand and drilling holes in a general horizontal plane outward from the chamber in a pattern similar to that of the spokes of a wheel. The project was undertaken by the Venango Development Corporation in an attempt to find an efficient method of recovering oil from partly depleted sand formations.The Venango Development Corporation is composed of the following oil-producing and oil-refining companies and individuals: South Penn Oil Co., Forest Oil Corporation, Kendall Refining Co., Minard Run Oil Co., Quaker State Oil Refining Co., The Pennzoil Co., Alliance Oil Corpo¬ration, United Refining Co., Franklin Creek Refining Corporation, Canfield Oil Co., Pennsylvania Refining Co., Page Oil Co., Freedom Oil Co., D. W. and D. S. Grant, and J. P. Herrick, C. M. Davison and N. V. V. Franchot. Engineering features of the project were supervised by a committee off three engineers A. J. Saxe, chairman, W. M. Shoemaker, and C. N. Pfohl, who supervised the excavation of the shaft and the drilling of the first two holes by alternately spending a week at a. time at the project. The drilling method was under patent license from Leo Ranney, who served as technical advisor to the Venango Development Corporation; in addition, he furnished the design for the shaft and work chamber."

Sep 1, 1944

By Stephen C. Tadolini, Thomas E. Marshall, Cecil Banta, L. J. Prosser, Anthony T. Iannacchione

The Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) endeavors to provide national and world leadership in the prevention of work-related illness, injury, and death. This is accomplished by using a scientific approach to gather information, assemble and create knowledge, then translate the knowledge and results into products and services. These products and services are then delivered to all personnel who can effect prevention. Obviously, the development and use of instruments to monitor mine roof conditions provides an opportunity to execute that mission. In the late 1990’s, based on observations at a number of underground limestone mines, only a few used roof monitors. Subsequently, NIOSH introduced the Roof Monitoring Safety System (RMSS) as an aid to roof inspection beyond traditional visual and sounding techniques. Initial expectations were that by gaining roof movement information, ultimately roof sag rates could provide indications of eventual failure. During this investigation, RMSSs were installed in 13 underground limestone mines in six states and this paper analyzes the data obtained at three of these mines. This paper also provides an overview of the system, data, analysis, and applications relevant to the RMSS.

U.S. Minerals Coordinating Council Advised. -The Critical Materials Act of 1981, H. R. 4281, introduced on July 27, would create a Council on Critical Materials in the White House Executive Office to oversee Federal materials programs involving $1 billion committed to research by 14 agencies, and to serve as the President's focal point to evaluate materials policy. It was introduced by Congressman Fuqua (D-Fla.) whose Committee on Science and Technology has over-sight over the implementation of P. L. 96-479, the National Materials and Minerals Policy, Research and Development Act of 1980. Bulgaria's Mineral Bank. -Recently Bulgaria established a mineral bank to facilitate receipt of foreign credits for exploiting Bulgaria's mineral raw materials. The bank has wide powers to enter into business arrangements with foreign creditors. Bulgaria's main interest in trading with the West is to import the technology for developing energy and mineral resources.

Jan 1, 1981

By Charles Vaught, Jeff Duncan, Michael J. Brnich, Lisa J. Steiner

This document contains most of the materials needed to use the exercise. The main part of the document is the instructor's copy. It tells how to use the exercise, presents the objectives, the master answer sheet, the scoring key, and discussion notes to be used following the exercise. The next section summarizes results from field tests of the exercise, and reports the miners' evaluation of the activity. The last part of this document is three appendices. Appendix A is the exercise problem booklet. This booklet can be duplicated locally. The booklets are reusable. One is needed for every person in the classroom. Appendix B is the answer sheet. Copies of this answer sheet must have the latent image (invisible) ink answers that appear in Appendix C printed on them.3 Answer sheets are consumable. One is needed for each person or each small group of persons who work the exercise. Exercise Summary Read this section first. It determines if the exercise is appropriate for your classes. If you choose to use the exercise, examine the table of contents and review the remainder of this document. Type: Latent image Audience: Remote control and extended cut miner operators and face crews Length: Eight questions (30 minutes for administration plus 30 for discussion) Skills: Remote control mining procedures including remote control mining, taking extended cuts, resetting breaker on mining machine, and setting timbers. Communicating mine conditions, influencing safe behaviors when mine conditions are less than stable Location: Underground coal mine, four section continuous mining operation Average seam height is 48 inches Problem: Your regular job is on the general labor crew at Cripple Creek #9 mine, a four section continuous mining operation. The mains are 9 entries wide and panels are 5 entries across. You and the rest of the crew had annual refresher training about 3 months ago. For the past few days you have been sent to 2 South panel to fill in as the third shuttle car operator. This morning, however, your buggy is down. The face boss asks you to get the scoop and take seven or eight timbers to the number 5 entry because the last shift got off sight line. The miner will be working in entry 5 while the bolter crew pins entry 4. When you get up to the face you see that Mo, the remote control continuous miner operator, has rounded off the left inby corner in order to make his first cuts in the right hand rib. Now, he has squared around enough so that you and Red, the miner helper, can set some posts on the corner. The two of you set posts along the left inby rib of #5 entry while the shuttle car operator waits. You are in a tight spot when Mo decides to start mining. You must decide where the best place is to stand for safety and to be out of the way.

Jan 10, 1999

By E. P. Youngman

Zirconium, formerly distinctly a rare element, is rapidly becom- ing of rather extensive commercial importance. Economic features of the zirconium industry, together with general information regarding the metal and its compounds, are discussed in a separate paper, to which this paper is a supplement. In addition to giving a brief discussion of the four or five de- posits that so far have proved to be commercial sources of the element, this circular summarizes available data (including some hitherto unpub lished material from the files of the Bureau of Mines) upon other occur- rences, including many of scientific interest only, of the two commercial. minerals, zircon and baddeleyite, and also data upon some of the minor minerals, such as eudyalite and cyrtolite, which have attracted addition- al interest in recent years because they are frequently richer in hafnium than the more common zirconium minerals.

Jun 1, 1931

By Ronald M. Hays

The Duluth Gabbro Complex in Northeastern Minnesota possibly contains a significant domestic copper resource and the nation's largest nickel resource. Exploration has discovered large low-grade copper-nickel (Cu-Ni) deposits between Hoyt Lakes and the Boundary Waters Canoe Area (BWCA). The mining and processing of Cu-Ni will have environmental, economic, and social impacts. The purpose of this study is to relate major environmental, economic, and social considerations to various aspects of Cu-Ni extraction. An open pit and two underground (block caving and open stoping with backfilling) models were developed to generate information on the impact of Cu-Ni extraction. Important considerations having environmental, economic, and social impacts (luring various aspects of Cu-Ni extraction are identified and defined. These aspects are exploration, development, mining, beneficiating, smelting, transportation, and termination of operations. Considerations are grouped into the general categories of site, industrial, energy, climatic, resource, water, air emission, waste disposal, employee, tax and royalty, transportation, and community considerations. Cu-Ni extraction in Northeastern Minnesota presents major environmental, economic, and social risks. Decisions are required on trade-offs between adverse and beneficial impacts. The approach used in this study assists in assessing environmental, economic, and social impacts. It will aid in the examination of potential and projected short-term and long-term advantages and disadvantages and will aid in the development of Minnesota's Cu-Ni resource for the maximum benefit to society.

Jan 1, 1974

By Jeffrey Shawn Peterson

The testing procedures of the U.S. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break- flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 2002

By Dana C. Reinke

A job analysis is a written list of the tasks associated with doing a particular job. In drilling, describing the steps associated with adding rod to the drill steel would be an example of a task associated with the job. How to hammer casing or fish a lost drill bit out of a hole would also be job tasks. Develop a written list of job tasks. Ask drillers in your company if the tasks listed are correct and accurately reflect how to perform the job. While each driller may do the job a little differently, some tried?and?true methods are required to perform certain tasks safely and correctly. You may find a separate analysis is needed for different drilling jobs (e.g., a residential well or a monitoring well). Also remember to include the tasks of both the helper and the driller.

Jan 1, 2005

By K. M. Connor, O&apos

Variations in overburden geology must be considered in applying subsidence prediction methodologies developed by the U.S. Bureau of Mines (USBM). To characterize rock mass overlying high-extraction coal mines, the USBM utilizes a computer spreadsheet program and modified Rock Mass Rating (RMR) system. The spreadsheet calculates an RMR based on a bed's engineering properties determined from core logs and laboratory tests. An in situ deformation modulus and a bending stiffness are computed for each bed. Stiffness-versus-depth plots identify groups of beds with similar stiffness. Large variations in stiffness between adjacent beds are considered significant horizontal discontinuities where slip is likely. Time domain reflectometry (TDR) is used to verify this hypothesis by measuring shear displacement along such discontinuities. A model of the overburden is built by assuming that a near-surface laminated beam exists above a transition zone in which large plastic slip occurs along horizontal discontinuities. Increasingly thicker groups of beds are modeled to determine the most probable beam thickness based on a comparison with measured deflection profiles. The inverse of maximum beam deflection is an index parameter known as "bridging potential," a single value that incorporates both overburden geology and mine geometry.

Jan 1, 2010

By Alfred Petrick

This report analyzes the byproducts systems of lead, zinc, uranium, rare earths, iron, aluminum, titanium, and lithium. Specific byproduct metals covered are cadmium, germanium, indium, and thallium from the zinc system; antimony and bismuth from the lead system; vanadium, radium, and scandium from the uranium system; rare-earth oxides from the rare-earth system; and cobalt, gallium hafnium, and rubidium from other systems. The report discusses various metallurgical systems, marginal and incremental production costs of byproduct subsystems, industry structure and organization, and historical data on price, consumption, and supply.

Jan 1, 1973

By Edward A. Metz, R. Larry Grayson, Douglas F. Scott

We describe inconsistencies in disease and illness reporting in U.S. mining, identify under-reporting of disease and illness in U.S. mining, and summarize selected disease and illness in U.S. mining from 1983 through 2001. Methods: We summarized information on mining-related disease and illness data for the years 1983-2001 from the Mining Safety and Health Administration database (MSHA). Results: Discrepancies exist in types of information collected by the Centers for Disease and Control, the National Institute for Occupational Safety and Health, and the Mining Safety and Health Admin¬istration database. Several factors, including a worker's fear of losing his or her job, health insurance, or other job-related benefits contribute to under-reporting of disease and illness information in the US mining industry. Conclusions: Since 1997, both number of workers employed in mining and disease and illness rates have decreased; however, the highest disease and illness rates in mining continue to be coal worker's pneumoconiosis and hearing loss.

By John J. Sammarco

The mining industry has the highest average annual fatality rate among major U.S. industries. To address this, the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory (PRL), is conducting major research programs to reduce the hazard exposure of miners. One of the recently concluded programs at PRL developed the enabling technology for remote-controlled mining. An application involves the manual process of extracting and hauling coal where operators, in the tight confines of a mine, can be struck or caught by mobile machinery. The approach to remedy this problem uses a guidance system on the continuous haulage equipment so that it follows the continuous mining machine that extracts coal. This, in essence, involves sensor-based docking of the machines. Sensors functioning in the hostile mine environment of dust, methane gas, and water play the key role. Computer analysis of the mining machine's movements and empirical machine characterizations established operating requirements and spatial limitations to ensure proper loading of coal into the haulage equipment. These data served in the selection of a guidance sensor. Technologies such as scanning laser systems and ultrasonic sensors have frequently been used in other applications, but were found unacceptable. However, a near-infrared sensor employing active targets met the requirements. The sensor has a nominal 75b conical field of view and a range from 0.1 to 18.0 m. For the single-target mode, nominal range accuracy was 4.3% at a distance of 3.65 m. Correction algorithms were generated, which reduced the error to 0.6%. Airborne dust testing showed less than an additional0.8% accuracy (worst case) degradation at dust levels up to 15 mg/m3. Using four targets, the nominal range accuracy was 0.4% without correction algorithms. Analysis of dynamic testing of a continuous miner and haulage showed that accuracy was maintained and total target loss did not occur. A guidance system for the haulage system to follow the mining machine does not exist commercially. Such a system can reduce fatalities, injuries, and exposure to dust and noise.

Jan 11, 1998

By K. L. Paciorek

The aim of this program was to develop a reliable and meaning-ful basis for assessing certain safety aspects, namely fire and, in particular, toxicity hazards of articles employed in underground coal mining operations. The present investigation was concentrated on the thermal oxidative degradation of representative hydraulic fluids. To achieve this goal all products formed on thermal oxidative degradation of the fluids studied were analyzed, identified I and the amount of each individual species present was determined quantitatively on a weight of product per weight of material basis. The weight/weight data thus obtained can then be factorized to reflect the relative toxicity of each individual species present, using for example the Threshold Limit Values adopted by the American Conference of Governmental and Industrial Hygienists, whereby an overall "toxicity index" can be arrived at which makes it possible to compare the different fluids and/or classes of fluids in a quantitative manner insofar as their toxicity is concerned.

Jan 1, 1976

By R. S. Dean

This is the fourth of a series; of annual report of the Metallurgical Division to be released in this form and cover the fiscal year July 1, 1937, to rune 30, 1938. This report is not merely a recitation or brief of the year's work; it contains technical information in usable form, although a some of this has appeared or will he issued in greater detail in separate reports. The table of contents that follows fists the principal investigations accomplished and those that are being continued. Other projects are being begun and contemplated for the next year.

Jan 1, 1938

By R. S. Dean

[During the past year the Metallurgical Fundamentals Section gave about an equal amount of time to the experimental determination of fundamental thermodynamic constants and to the demonstration of the application of such data to more directly practical metallurgical problems. The first division of the work - the actual experimental measurements of typical thermodynamic constants - was carried out an two problems, termed ?continuing? programs, namely, (1) measurements of Specific Heats at Low Temperatures and (2) Measurements of Heats of Formation and Free Energies. Specific substances chosen for investigation are classified as (n) those that have been the subject of requests for information from the industry and that, upon examination, seem of sufficient practical importance to justify study, and (b) compounds that are difficult to treat metallurgically, or whose specific thermodynamic properties have not yet been determined satisfactorily and for which accurate data might suggest improved or new methods of Metallurgical treatment, or (c) materials recognized as belonging to a social class with exceptional thermodynamic properties and, hence, of scientific as well as technical importance.]

Jan 1, 1938

By O. C. Blade

Diesel fuel is being used in greater volume than ever before in the United States. During 1950 railroads used 43 percent of the total volume of Diesel fuel sold, smelters, mines, and manufacturing plants used about 13 percent, highway vehicles such as trucks and busses, and equipment such as tractors and bulldozers accounted for approximately 20 percent, about 12 percent was used by water craft, and the remaining 12 percent by gas and electric utilities, the military forces, and oil companies. These figures were calculated from data issued by the Bureau of Mines. 2/ Comparable figures for 1951 and for 1952 to date are not available, but recent information indicates that well over 11,000,000 barrels of Diesel fuel per month are produced by the country's refineries. 3/ More information on this increasingly important type of engine fuel is needed by the petroleum industry, engine manufacturers, and consumers, particularly on the grades and qualities of the Diesel fuels being marketed. To supply this information the American Petroleum Institute and the Bureau of Mines, United States Department of the Interior, under cooperative agreement, are conducting annual surveys of Diesel fuel oil produced in refineries in this country.

Jan 1, 1952

By Parry. V. F., John B. Goodman

"INTRODUCTION The Denver region coal field, covering an area of approximately 7,640 square miles, extends from the Wyoming State line to the middle of El Paso County, Colo. The coal in this region is subbituminous in rank. Much of it is used as domestic fuel. During the last decade the production of coal in this field has remained fairly constant at an average of 2,600,000 tons per year. This production has come from 50 to 60 mines, 88 to 90 percent of the production being from the section of the field north of Denver.According to the Standard Specifications for Classification of Coal by Bank of the American Society for Testing Materials 4/ the coals in this region are classified in the Subbituminous B and C group. On the as—mined basis, they contain about 22 percent moisture and average 9,600 B.t.u. per pound. They are noncoking and slack to a variable extent when exposed to the weather. This is characteristic of subbituminous coals."

Aug 1, 1939

Recent Bureau of Mines research in earth grounding safety is documented in three separate papers. First, guidelines for the design of a 5- ohm borehole ground are presented. Next, an inexpensive practical means to construct a low-resistance bed in high-resistivity soil is described. Finally, a procedure that employs a commercial resistivity meter to measure shock potentials around grounded objects is explained step-by-step. These papers complement the material presented at an earlier technology transfer seminar and published as IC 8767.

Jan 1, 1985