Search Documents

By E. H. Skinner

An abandoned mine shaft near Omar, in Logan County, W, was permanently sealed through a cooperative agreement between the West Virginia Department of Commerce, Labor, and Environmental Resources, Division of Environmental Protection, and the US. Bureau of Mines (USBM), Abandoned Mine Lands (AML) Program. An engineered shaft seal design was developed and demonstrated that featured lightweight concrete as a key material component at a wet density of about 45 lb/ft3. A reinforced concrete cap designed for 5 psi live load was placed over the shaft seal. Applicable new concrete technologies relating to a 100-yr design life were utilized to assure future integrity of the shaft seal. Waterproofing methods were included in the shaft seal design to provide protection from ambient moisture and corrosive mine waters and to increase the long-term durability of the shaft seal. All construction methods used in the field trial are fully adaptable for the mine-reclamation contractor, The USBM research objectives were to develop a broad generic design that will be widely applicable to other adit-sealing and shaft-sealing problems throughout the mining industry.

Jan 1, 2010

By Thomas L. Vandergrift

To significantly increase the stability of underground excavations while exploiting the full advantages of confined rock strength, methods must be developed to actively control the distribution of stresses near the excavation. This U.S. Bureau of Mines study examines theoretical and practical aspects of rock pres¬surization, an active stress control concept that induces compressive stress in the wall rock through repeated hydraulic fracturing with a settable fluid. Numerical analyses performed by incorporating the rock pressurization concept into a variety of boundary-element models indicate that rock pressurization has the potential to improve underground excavation stability in three ways: (1) by relocating stress concentrations away from the weak opening surface to stronger, confined wall rock; (2) by inducing additional stresses in a biaxial stress field to reduce the difference between the principal stress components near the surface of the opening; and (3) by counteracting the tensile stresses induced in the rock around internally loaded openings. Practical aspects of the rock pressurization concept were investigated through a series of hydraulic fracturing experiments. The use of sulfur as a settable fluid for hydraulic fracturing was demonstrated, although problems related to sulfur viscosity suggest that other molten materials, such as wax, may be better suited to practical field application of the rock pressurization concept.

Jan 1, 2010

By J. Ritchey

This report describes the engineering feasibility and economic advantages of using a mobile bridge-type cross-pit belt conveyor system in conjunction with a large dragline to excavate and transport spoils in a typical Western surface coal mine. The studies show that such a system could be built to survive operational and climatic mining conditions, and that its implementation would offer a reduction in both acquisition and operating costs versus conventional mining units of comparable rapacity. Reclamation costs can also be significantly reduced, and the total reclamation process accelerated, making the cross-pit conveyor system attractive to mine Owners and environmentalists alike.

Jan 1, 1976

By L. C. IlsLey

In January, 1922, a conference relative to trailing cables for use with permissible mining machines was held at the Pittsburgh Experiment Station of the U. S. Bureau of Mines. At this conference it was recommended that the bureau take steps to investigate the rubber-sheathed type of cables and to bring about the establishment of a list of approved cables. Effective until such time as a complete investigation could be made, the bureau asked the several manufacturers holding approvals for mining machines to recommend cables for use with their machines. In general the cables recommended were tentatively approved. Due to the lack of available personnel, no actual tests of cables were made until mid-1927. Meanwhile a field investigation of trailing cables was made at 20 mines of three coal companies in western Pennsylvania, and samples of cables were obtained from the manufacturers for laboratory tests. Twenty-five samples of the concentric-type cable, representing the product of five manufacturers, were obtained for the tests. These cables were of four sizes, as follows: 3 cables of No. 2 B & S gage, 17 cables of No. 3 B & S gage, 3 cables of No. 4 B & S gage, and 2 cables of No. 6 B & S gage.

Jan 1, 1929

By V. Ferrari

This report documents the three-phase program to design, fabricate, test, and demonstrate economical and practical methods of reducing noise levels on underground coal mining portal buses (mantrip vehicles). The noise-control treatments applied to a production-model portal bus were as follows: ? Wheel/rail vibrations were isolated from the vehicle frame by inserting elastomeric materials between suspension components. ? Vibration-induced noise was reduced by replacing all large sheet metal panels (except floor plates) with damped steel panels. ? Motor noise was reduced by tight-fitting covers made from damped steel and lined with sound-absorbing material, and by elastomeric motor mounts. ? The standard spur gears used in the traction drive system were replaced with helical gearsets. The program achieved the goal of reducing the average sound-level to below 85 dBA for typical operating conditions.

Jan 1, 1981

By Lowell Stroud

Since 1929, the Helium Activity of the Bureau of Mines has operated a helium-extraction plant at Amarillo, Tex. The natural gas that supplies this plant is obtained from the Cliffside geologic structure 12 miles to the northwest and over the years, has become known simply as "Cliffside gas," There is need for published data on the low-temperature phase equilibria of helium-bearing natural gases. To date, little information has been published on the equilibrium phase compositions, solution of helium in condensed natural gas, condensation characteristics, or equilibrium vaporization coefficients for methane, nitrogen, and helium in helium-containing systems. A windowed phase equilibrium apparatus (8)6 was used to obtain 105 equilibrium samples, representing 35 experimental conditions of condensed Cliffside gas at pressures of 100, 200, 300, 400, and 500 p.s.i.a. and temperatures from 0° to -270° F. Data on equilibrium vapor-liquid composition for Cliffside gas are presented in both tabular and graphic form and are discussed in detail to show their relationship to certain criteria that must be met to effect an efficient separation of helium from natural gas by means of low-temperature processes. Facts about condensation characteristics and solution of helium in the liquid phases are included, The important relationship of these two factors in decreasing the percentage of total helium lost by solution in the liquid phase is discussed.

Jan 1, 1961

By Anthony M. Opyrchal

This Bureau of Mines study assesses the economic significance of the Florida phosphate industry to selected counties in Florida, the State of Florida, and the Nation: it also includes a brief survey of the industry's international impact. Based on forecasts of Florida phosphate production in 1981, and using constant 1977 dollars. estimates are given for 1981 for regional and national output the value of this output, income, and employment created by the phosphate industry in Florida, Federal, Stale, and county tax revenues generated by the State's phosphate industry are also estimated for 1981. The concentrated impact of the phosphate industry on certain areas of Florida and on the State?s regional industries is examined using economic base analysis complimented by an industrial complex approach. The industry's impact at the Stare and national levels is examined through input- output analysis. In addition, an attempt to forecast for 1990 the effects of constraints on phosphate rock mining as a result of economic conditions and other factors is included as an appendix to the report. Also discussed is the phosphate industry's importance to the U.S. balance of trade: U.S. agricultural production. Including forward linkages; the U.S. sulfur industry; and the phosphate industry's importance to the production of fluorine and uranium by- products from fertilizer manufacturing.

Jan 1, 1981

By J. K. Whyatt

During the past 2 years, U.S. Bureau of Mines (USBM) researchers reviewed an in situ stress investigation conducted in 1977 at a test site on the 4250 level of the Lucky Friday Mine, Mullan, ID. Although the field measurements of over core strain were found to be useful, significant deficiencies were found in the stress field estimation procedure. The stress field estimate was then updated to incorporate recent progress in statistical capabilities and new understanding of stress concentration factors for doorstopper cells, as well as to correct an error in the original stress solution procedure. Simple models were used to examine the possibility that systematic variations in material properties and stress fields existed at the site. These models succeeded in reducing the sum of squared error somewhat, but fell short of completely describing stress variations throughout the test site. This overcore measurement will be supplemented by two other measurements described in the second and third reports of this series. Other observations of stress field characteristics are discussed in the fourth report The final report will also characterize the natural in situ stress field in the vicinity of the Lucky Friday Mine. This work was undertaken to support USBM research on mining method design and rock-burst control for deep mines.

Jan 1, 2010

By D. Harrington

"Up to the last 10 or 15 years, responsibility for accidents in mines was generally, though not universally, placed upon the person or persons immediately involved. Present-day thought is rapidly veering toward holding the industry responsible for accidents, with ultimate payment of the bill by the consumer, if financial expenditure should be necessary. While it is undoubtedly correct in principle that responsibility for accidents in and around mines should be shouldered by the employer and while it is probable that as time passes the burden will become even more definitely than now that of the mining companies, on the other hand it is an undeniable fact that large numbers of accidents occur through acts of omission or of commission of some person, very frequently the victim of the accident being the offender.Out of about 3,000 persons killed every rear in our -mines and quarries, nearly half or approximately 1,500 of the fatalities are due to falls of overlying material or of persons, about 500 to haulage, about 350 to fires and explosions, about 125 to explosives, approximately the same number to electricity, and about 300 to various miscellaneous accidents.Generally the accidents from falls involve but one or two persons at a time, and the tendency is now as it always has been to charge the victim or possibly a coworker with the responsibility. Usually this sort of accident occurs at or near a working face (statistics indicate that about 80 per cent of fatalities from falls of roof or rib occur near the face), and as it is Generally agreed that it is the duty of the worker to keep his working place safe, the worker and especially the face worker is given the blame in case of accident."

Apr 1, 1930

By Charles T. Holland

ANALYSIS of 117 occurrences of bumps in coal mines shows that 67.6 percent are associated with pillar-line points.4 Slabbing and splitting pillars, development, and other unfavorable milling practices in abutment areas may be a contributory or the primary cause of bumps. The cure for pillar-line bumps is to recognize areas that can be expected to become highly stressed and to project the mining plan and operations to eliminate such areas insofar as possible. If such areas cannot be eliminated, then the mining plan and operations should be projected to avoid the necessity of disturbing these areas before the stresses have been dissipated.

Jan 1, 1954

By W. L. Hunter

This report describes results of beneficiation and smelting studies conducted by the Federal Bureau of Mines on chromite samples from the Emma Belle and Seiad Creek prospects in the Seiad Creek area, northern California. Samples were chosen from this area because the ore is typical of disseminated types that represent a sizable domestic reserve. The two samples were similar in composition, and both responded in like manner to gravity beneficiation. As the ore was banded, considerable coarse gangue was rejected in laboratory sink-float from a minus-3/4-inch, plus-6-mesh fraction without excessive chromium loss at a medium density of 3.32. An average of 85.6 percent of the chromium was recovered in the sink product, which analyzed 35 percent chromic oxide (Cr203). Tabling yielded concentrates containing 49 percent or more Cr203; however, recoveries, ranged from only 33 to 45 percent. A combination of tabling and electrostatic separation of the table middlings showed that the chromium recovery could be increased to about 73 percent; the composite concentrate averaged 53 percent Cr203.

Jan 1, 1960

By David A. Summers

Coal is increasingly viewed as one of the major fuel resources of this country for the remainder of this century. The need to extract a greater percentage of the coal in a given seam, together with advantages of improved safety, indicates that longwall mining will become more widely used within this time frame. A novel method of mining coal on a longwall face, utilizing high pressure water jets, is herein described. The mining machine proposed will exploit the stress conditions which exist on a longwall panel in order to achieve the required productivity while at the same time reducing respirable dust and methane ignition hazards. The water jets will excavate only the boundary of the extracted seam section, and thus the energy requirement of the machine will be minimized. The action of the machine is similar to that of an existing coal plow, except in that the wedge teeth of the plow are replaced by oscillating high pressure water jets. The machine can, therefore, cut to the depth and at the speed of existing shearer units at equivalent power levels. The removal of impact stresses from the machine will reduce downtime required for maintenance and replacement of picks and lower the load on the haulage motor of the system. The ability of the machine to increase the depth of cut without an increase in horsepower will further improve productivity when transportation systems to remove the greater production are in operation.

Jan 1, 1974

By Robert M. Busche

[Recent developments in the gasification of coal, both by the Bureau of Mines and American industry, have intensified interest in the thermodynamic and kinetic principles necessary for understanding the reaction mechanism and rates and the physical changes that take place. In the course of a Bureau of Mines study of the kinetics of coal gasification at the Synthetic Liquid Fuels Demonstration Plant, Louisiana, Mo., a bibliography of approximately two references was compiled. They are listed n this publication and refer both to American and foreign sources.]

Jan 1, 1952

The objective of this study was two-fold: 1. To perform a world literature search pertinent to the analysis, selection and design of hoisting systems and their components and to codify the search into a literature compendium. The search resulted in a technical data file of over 1500 hard copy items. The compendium index was also suitable for establishing a comprehensive computer-loaded data base on the subject. 2. To develop a comprehensive system of guidelines to cover salient aspects of analysis, selection and design of electrical, mechanical and structural components of a hoisting system with a view to establish parameters for maximum safety and efficiency of operation, installation and revision of the system. 3. Major mechanical components in the hoist and mechanical drive train are considered. Design and specification criteria based on American standards and practices are developed as they apply to typical mine hoist arrangements.

Jan 1, 1988

By E. P. Youngman

Before the World War the use of zirconium and its compounds was largely experimental and confined almost wholly to Germany and Austria . Occasionally small lots of zirconium ore had been produced in the United States ( 1,000 pounds in 1869 , 26 tons in 1883 , and 3,000 pounds in 1903 ) and used (with monazite ) in the manufacture of various lighting devices , especially incandescent gas mantles ; but it was not until 1906 that the discovery of the natural zirconium oxide in large quantities near Sao Paulo , Brazil , first gave promise that a zirconium industry eventually might be developed . Edward Rietz , who worked the Brazilian deposits , interested German chemists in extending the use of zirconium , and by 1911 trade journals were listing German firms as manufacturers of compounds or products derived therefrom . For a time zirconia was one of the various oxides used in the Nernst lamp . It was used also for crucibles and hearths as refractory material ; in the manufacture of chemical utensils ; in enamels ; in the place of bismuth subnitrate for defining Röntgenray pictures of the stomach ; as a pigment ; in medicine ; and in a number of other ways . The Germans were credited also with producing a remarkable zirconium steel , which , it was claimed , was much superior to other alloy steels . During the World War the United States Government investigated the possibilities of zirconium , as well as those of other steel -hardening elements , and a large automobile manufacturer actually purchased a substantial quantity of ore with the purpose of employing zirconium in automobile steels . Immediately after the armistice the Government ceased its investigations ; but despite the difficulties experienced by various investigators in reaching concordant results , interest in the use of zirconium as a steel -hardening agent , as well as in other uses of the element and its compounds , continued . In 1918 the Foote Mineral Co. , which had been interested in zirconium for several years , was exploiting the deposit in Brazil formerly worked by the Germans and was supplying zirconia in the form of ore , brick , and cement for refractory and other purposes . About the same time the Electro Metallurgical Co. , which before the entrance of the United States into the war was experimenting with zirconium alloys , supplied in tonnage quantities the demand for these alloys . In 1919 it was reported that American manufacturers , after several years of research, were producing in commercial quantities pure zirconium oxide , which was finding a place in the manufacture of small refractory articles , scorifying dishes , crucibles , tubes , and one- piece furnace linings . In 1920 the lowering of the price of zirconium metal powder ( because of improved metallurgical methods ) promised the production of the metal on a semicommercial scale . In 1924 the Titanium Alloy Manufacturing Co. introduced a new opacifying agent , " Opax , " made from zircon . A year or two later some of the large pottery manufacturers became interested in the use of zirconium oxide as an opacifying agent , the increased production of titanium pigments having resulted in the production of zirconium as a by-product at a price that could compete with tin oxide . In 1928 it was reported that the industrial use of zirconium oxide was increasing steadily in the manufacture of brick , crucibles , and other refractory products , such as high- temperature cements . However , the reluctance of producers to install additional and more suitable

Jun 1, 1931

By G. L. Oldright

By means of a technique developed in cooperation with the Eagle-Picher Mining & Smelting Co. and outlined in the first report of this series (R. I. 4333 ), it was possible to take many thermocouple readings with base-metal couples at temperatures over 2300° F with unsupported protection tubes for over half the lengths of the Henryetta retorts. -This technique made it possible to avoid the use of the usual optical pyrometer, which gives temperatures dependent upon the luminosity of the flames, and which is not conveniently usable to read temperatures for the lengths of the retorts from the front of the furnace. The temperatures of the retorts themselves were necessary in order to set upper limits for safe operation; the lower limits of operating temperatures are set by the zinc content of the retort residues. The zinc content left in the retort residues for various sections of length also varies with retort temperatures rather than with flame temperatures. The variations in temperature along the retort can then be used as guides to distill more zinc from the residues, to avoid fluctuations in the rates ,of flow of zinc vapor into the condenser and to employ lower temperatures if such rates become high enough to cause losses of uncondensed zinc.

Jan 1, 1948

By E. G. King

Thermodynamic calculations involving the oxides of tungsten and molybdenum have been hampered by lack of accurate entropies and high temperature heat contents. This paper presents work by the Federal Bureau of Mines on new low-temperature heat-capacity data leading to the evaluation of the 298.15° K. entropies of tungsten dioxide and tungsten trioxide, as well as high-temperature heat contents (above 298.15° K.) of molybdenum dioxide, molybdenum tri-oxide, tungsten dioxide, and tungsten trioxide. Included are heats of fusion of the two trioxides. The heats of formation at 298.15° K. of these four oxides are tabulated as measured by Mah4 5/ of this laboratory. Included also are the 298.15° K. entropy of Mo02 measured by Kin 6/ of this laboratory, and that for Mo03 according to Kelley and King.7/ These basic data provide a consistent compilation from which to perform accurate thermodynamic calculations involving these compounds. No previous low-temperature- heat-capacity measurements have been reported for tungsten dioxide. Seltz, Dunkerley, and DeWitt8/ measured the low-temperature heat capacity of tungsten trioxide. The only previously-reported high-temperature heat-content measurements for any of the oxides were conducted by Cosgrove and Snyder,9/ who measured molybdenum trioxide to 1,300° K.

Jan 1, 1960

By Joseph J. Wallace

1. The investigation shows that there are 2 coal beds of major importance in Letcher County from the standpoint of present production - Upper Elkhorn No, 3 and Fire Clay - and 5 beds of minor importance - Whitesburg, Flag, Haddix, Elkhorn Leader, and Amburgy, The Upper Elkhorn No. 3 and Fire Clay beds contain the largest remaining known reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,600 tons per acre-foot of coal in place, are estimated at 1,353 million short tons as of January 1, 1952. Of this total, 1,056 million short tons ere in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bad characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1953

By Robert M. Doerr

The purpose of the investigation was to determine the oxidation behavior of selected tungsten-cobalt alloys. Specimens of Wand W-Co containing 0.7, 1.7, 3.4, and 9.7 weight-percent Co were subjected to pure 02 at 1,000° and 1,100° K, and specimens of W-Co containing 29.8 weight-percent Co, at 1,100° K. Reaction kinetics were determined volumetrically. For specimens other than those containing 29.8 percent Co, the reactions proceeded at about a constant rate at either temperature, indicating the formation of a scale of constant protectivity; the reaction rates were essentially independent of the Co concentration. The scales on these alloy specimens consisted principally of WO3 and CoWO4. Specimens of a 29.8 weight-percent Co alloy, consisting primarily of the W6CO7 phase, oxidized with only slight deviations from the parabolic rate law at 1,100° K. The protective scale on these specimens consisted chiefly of Co3O4, CoW04, and W1 8°49; Co3O4 was outermost, and the W18O49 was adjacent to the alloy. The results suggest that the Co-rich outer scale inhibited the inward transport of 0 to an extent sufficient to greatly limit the amount of the nonprotective WO3 formed, so that protective W18O49 formed instead.

Jan 1, 1967

By Robert H. Merrill, James V. Williamson, David M. Ropchan, George H. Kruse

In- situ rock stresses were determined by flatjack and borehole - deformation methods . Estimates of the stress distribution around a flatjack were obtained by a combination of flatjack and borehole - gage techniques . The investigations were part of a study , conducted jointly by the State of California and the Federal Bureau of Mines , to determine the stress in rock at the site of an underground powerplant for the Oroville Dam near Oroville , California . The stress distribution around each of three flatjacks was nonsymmetric ; however , stresses obtained from 9 flatjack and 157 borehole measurements are considered reasonably accurate for engineering purposes . The stress near the edge of the openings is between 800 and 1,600 psi ; the stress in the undisturbed rock is approximately 500 psi , nearly hydrostatic .

Jan 1, 1964