Search Documents

By T. G. Sitharam, P. B. Choudhury

Prediction of ground vibration (peak particle velocity, PPV) and frequency is an important task in geoscience. Till date, many empirical equations are derived from conducting trial blasts in the mines, to arrive at attenuation predictors. These predictors are usually site dependant and hold good for one particular type of rock/strata. These predictors cannot be used for geologically different rocks/strata. This paper presents the application of support vector machine (SVM) model, for predicting blast induced ground vibration and frequency, using a one comprehensive model for three different types of rock. Inputs to the SVM model formulation involve twenty one parameters consisting of geotechnical properties of the rock mass, blast design geometry and explosive properties, and the output of the formulated model is peak particle velocity and its associated frequency. The data has been acquired from eight limestone mine, five coal mine and two manganese mines. The comprehensive SVM model is formulated using 400 datasets and tested with 143 datasets. The performance indicators to the model not only justify its formulation but also the advantages it has over site specific predictor models. The SVM model not only predicts PPV, with higher correlation coefficients as compared to predictor equations, but also the associated frequency.

Jan 1, 2010

By James Rowland, Marcia Harris, Richard Mainiero, Michael Sapko

All explosive materials produce a cloud of reaction products, the most toxic of which is nitrogen dioxide (NO2). In the study reported here, 4.5-kg (10-lb) charges of blasting agent confined in either thin-wall 10-cm (4-in) diameter galvanized pipe or 10-cm (4-in) schedule 80 seamless steel pipe were detonated in a closed chamber. The detonation gases were analyzed for NO2, nitric oxide (NO), ammonia (NH3), hydrogen (H2), carbon monoxide (CO), carbon dioxide (CO2), nitrogen (N2), oxygen (O2), and methane (CH4). Data were evaluated to determine the kinetics of the oxidation of NO to NO2. Analysis revealed that the only mechanism for NO loss for the conditions existing in the chamber was the reaction 2NO + O2 6 2 NO2. The rate constant was 2.08 ?? 10-38 cm6 molecules-2 sec-1 for the rate equation -??d [NO]/dt = K ?? [NO]2 ?? [O2] for NO concentrations up to 100 ppm. The rate constant is in agreement with that recommended by Baulch, Drysdale, and Horne (1973).

Jan 1, 2006

By Noel Dent

The Electrodet@ Electronic Detonation System Wilere are we going with regard to Accurate, Reliable, Easy to Use and Cost Effective Initiation using electronic initiation techniques? Improvements and applications in theJierd

Jan 1, 1995

By Jack Eloranta

"This paper compares energy requirements for blasting, crushing and grinding. By tracking electricalconsumption for various powder factors, a general trend has appeared. This study involved over 100million tons of ore and powder factors ranging from .5 lbs/L,T to .8 lb&T. Actual energy usage iscompared to predicted energy based on the Bond equation."

Jan 1, 1998

By John Brown

Let’s talk about things that you, the driIl boss, the pit boss and the driller can do to eliminate the trend in drilling related accidents that have come to plague our industry in recent years. My paper will focus on reaI issues, problems and solutions that will affect our everyday outlook and attitudes about our jobs and lives. There are some real hard facts we must address if we are going to reverse this terrible killing trend.

Jan 1, 2000

By Russell D. Melton, Gary A. Kanelos

A construction company performed blasting operations to break up limestone bedrock for excavation of residential basements. The owners of an existing residence located approximately 400 feet from the operation claimed that vibration damaged the structure and created foundation subsidence by lowering the moisture content of the foundation soils.

Jan 1, 1996

By Ray Jambakhsh, Gabrielle Bourget

In the summer of 1998, Ontario Hydro awarded a contract to demolish an obsolete and inefficient chimney by blasting. The Ontario Hydro Thunder Bay Thermal Generating Station (T.G.S.), is a fully operational hydro thermal generating station located in Thunder Bay, Ontario, Canada. The Chimney was a 356 ft (108 m) high freestanding structure constructed of reinforced concrete with a brick liner. Falling the chimney required careful planning due to the highly sensitive structures and equipment which surrounded it. Damage either sustained to the existing systems through ground vibrations or direct contact would have resulted in expensive power outage and/or lost production. The role of Explotech Engineering Ltd. on this project was to provide and evaluation of the proposed demolition procedure, defme the predicted and maximum seismic vibrations at sensitive structures including underground services, conduct pre-blast / post-blast inspections and recommend various safety precautions. The general contractor for the project, LeBrun Northern Contracting Ltd., of Thunder Bay, Ontario was responsible for all site preparations and post-blast clean up. All demolition blasting calculations and operations were conducted by Dykon demolition experts from Tulsa, Oklahoma. On September 13, 1999, the chimney was successfully demolished. Extensive analysis of the vibration records and visual post-blast inspections of the surrounding structures concluded that the demolition event induced no damage to any of the Ontario Hydro facilities.

Jan 1, 2000

By C. Adcock, R. Farnfield, G. Adderley

The use of explosives to create special effects in the film industry is a well-known past time. A recent production required simulation of a large scale water splash from the effect of a statue falling from a cliff edge and impacting on an open body of water. This was to be achieved through the use of precisely delayed explosions detonated near the surface of the water. A survey of the area revealed a breeding farm for sea bass approximately 250 metres (273 yards) from the intended blast area. It was initially thought that the water pressures produced for the detonation of the explosives may cause harm to the fish. Much work has been carried out over the past few decades on the effect of open water blasting and its effects on aquatic wildlife; this includes water pressure modelling techniques which can be used as predictive tools.

Jan 1, 2010

By Ali Kahriman, Abdulkadir Karadogan, Alper Celtikci, Ahmet Varol, Ertugrul Kaya, Turgay Ozat

This paper presents analysis of environmental effects induced by cautious blasting during the construction of the Istanbul Subway 4 Levent - Ayazaga Darulsafaka Metro Tunnel Project carried out by the contractor, located at Northern Istanbul in Turkey. Within the scope of the study, for the prediction of the peak particle velocity and to determine the slope of the attenuation curves together with the maximum charge per delay for the S6-7-8 shafts of this tunnel route, ground vibration components were measured carefully by using five vibration monitors during the construction of the tunnels which required blasting. The particle velocities and frequency values of all blast events are evaluated according to the United States Bureau of Mines (USBM) and German DIN 4150 Norms in order to predict, and compare the influence grades to the neighboring buildings, and structures. Also, data pairs of scaled distance and peak particle velocity obtained from 107 records belong to 51 shots were analyzed statistically. Empirical relationships with correlation at the 95 % confidence interval were established for these tunnel excavations and suggested for the test sites in order to estimate particle velocity of the ground vibrations. As a result of the studies, some practical charts are created in order to minimize the psychological effects of the shots, and simplify the authorities of shots’ job. And last but not least, make sure that the shots will be done in a controlled way.

Jan 1, 2011

By Dale S. Preece

A Discrete element computer program named DMC @istinct Motion Code) has been developed for modeling rock blasting. This program employs explicit time integration and uses spherical or cylindrical elements which are represented as circles in 2-D. DMC calculations have been compared with measurements on bench blasts in the field with relatively good comparison. Structural rock mass characteristics have a significant impact on any blast and DMC has not, until now, included these effects. This paper discusses a recently added DMC capability for treating joints and bedding planes in bench blast simulations.

Jan 1, 1995

By G K. Jorkenson

The SABREX Blast Modelling Program was developed joinlly by the companies of the ICI Explosives Group. of which C-I-L Inc. is a member. SABREX (Scientific Approach to Breaking Rock with Explosives) is a modular computer program which incorporates new technology with a number of tested programs that have been in use world wide.

Jan 1, 1989

By T. Bernard, P. Dozolme

Electronic initiation devices appeared on the market more than 15 years ago and have definitely changed the rules of blasting. It becomes clear that this technology represents a powerful alternative to the traditional accessories. Electronic Delay Detonators (EDD) have attained solutions that were difficult and even impossible to achieve with the previous technology, thanks to the accuracy, usually inferior to one millisecond, and flexibility of the programmability range offering thousands of timing possibilities. Technological progress is long awaited to represent a step ahead compared with the last generation of products. In the case of electronic initiation, some limits nevertheless rapidly appeared, leading to the paradox of loosing operative and safety benefits, compared with the traditional technology it was supposed to outclass.

Jan 1, 2006

By D T. Froedge

With successive generations of the Iso-Seismic System, we are acquiring more and more information about the actual behavior of blast induced ground, and airborne vibration, as it propagates through the environment. Some of the original “truths” that have been long accepted may have to be \revised.

Jan 1, 1995

By Robert Hopler

It is the nature of the initial detonation to the powder around the cap which governs the greater or less effect of the explosion of the whole charge. The cap communicates to the first particles of powder a disruptive impulse, which, according to the nature and strength of the cap, more or less completely overthrows their equilibrium and decomposes the powder with great energy, setting up sympathetic vibrations that explode the particles of powder in turn by the violent disturbances or friction between them in a regular succession of impulses and decompositions, which, if started with sufficient energy, are of such intense heat and velocity that the rupturing force of the explosive is developed practically instantaneously. This detonation has already been shown to be not only the result of mechanical force, but a combination of extremely sudden chemical and dynamical reactions which set up vibrations to which different powders are more or less susceptible, and these explosive reactions will be propagated through the mass of the powder according to the intensity of the vibrations and the resistance with which their motion is opposed by the nature and consistency of the powder, whether it be difficult or easy to oxidize, soft and plastic like dynamite, or hard. If the initial detonation of the powder surrounding the cap is of the highest degree, the vibrations will be most intense and will be propagated further through the mass than by a poorer detonation. Hence the different degrees of detonation. Unless the first particles of powder are so thoroughly decomposed by a detonation of high order, or first degree, as to convey the necessary heat and energy to detonate the whole charge, the greatest force of the powder will not be developed. There will frequently be unbottomed holes or pieces of unexploded powder scattered about, or both, and the air in the mine will be contaminated with some obnoxious gases that have not been completely oxidized.

Jan 1, 2007

By A. K. Mishra

The mineral industry is leading towards a technology driven optimization process. Drilling and blasting are such unit operations in a mine, which can alter the balance sheet of the mine if not planned properly. The development, improvement and utilisation of innovative technologies in terms of blast monitoring instruments and explosives technology are important for cost effectiveness and safety of mineral industries. The ever-growing demand of mineral has compelled the industry to adopt mega opencast projects with big equipments. This has necessitated use of few hundred tonnes of explosives in each blast. The bulk delivered fourth generation explosives has solved the problem of explosive loading to a large extent. The priming of bulk delivered explosives in Indian mines uses the conventional PETN/TNT based cast boosters. As the conventional cast booster possess safety problems in terms of handling and use, so Indian Explosives Ltd., has developed an emulsion based cast booster (Powergel Boost).

Jan 1, 2005

By Fumihiko Sumiya, Shinya Tanaka, Yukio Kato, Kenji Tanaka, Tetsuya Sawada

When explosives are heated under an acidic environment due to metal sulfide and sulfuric acidity, their decomposition temperature falls remarkably and decomposition reaction occurs quickly, and then explosives have the risk of the deflagration to the detonation transition. Heat resistant commercial explosives which can be used under conditions of high temperature of 200ºC and an acidic environment were studied. We developed the explosive composition consisted of ammonium perchlorate (AP) as oxidizer, saturated hydrocarbon oil as fuel and binder, and calcium carbonate as decomposition inhibitor. The characteristics of this explosive composition show a heat resistance over 24 hours at 200ºC, and a detonation velocity over 2,500 m s-1. This explosive composition has a cap-sensitivity at temperature higher than 100ºC. Cost effective heat resistant commercial explosives were created by the optimization of the grain size of AP as a main component, the addition of saturated hydrocarbon oil and calcium carbonate, and the control of bulk density by the addition of micro-balloons.

Jan 1, 2003

By Marco Antonio Falquete

A novel spark-generating tube, containing no explosive in its composition, is evaluated and compared with conventional shock tube. The product overcomes a series of problems found in conventional shock tube technology. The technologic development had multiple aims: to avoid transport and storage costs associated with explosives, to be more environmental-friendly, to obtain a high-velocity, hightemperature spark whose thermal performance could overcome poor heat transfer to the delay charge by gas convection at shock tube end, and that could cross barriers such as tight kinks, close knots, cuts, extreme environmental conditions, and long-term hot explosive emulsion exposure. The product of this development is evaluated and compared with conventional shock tube in a series of aspects and performance tests, including spark thermal performance (ignition of tougher, low sensitive delay columns, spark gap test), propagation in critical conditions of use (kinks, knots, cuttings), extreme environmental conditions (long-term exposure to hot emulsion explosive, extremes of cold, heat, moisture, underwater exposure), safety features (ignition through flame, open fire), and security against terrorist acts. Due to the safe characteristics of the tube, a series of demonstrations will be performed during the presentation. In nearly all tests and aspects, the spark-generating tube exceeds conventional shock tube, and in the rest equals shock tube, making it a more reliable alternative.

Jan 1, 2005

Blast vibration analysis under relatively near-field conditions has been carried out in a narrow-vein underground operation. The objective was to characterize the vibration signal (particle acceleration and velocity) from carefully controlled stope blasts. The limitations of such analysis in deriving design guidelines for reducing dilution has been elucidated. It has been shown that identification of each individual hole with specific explosive types can yield explosive-specific predictive equations for particle velocity. This has been coupled with measurement of actual overbreak to arrive at a limiting vibration level to generate a realistic design tool for controlling dilution in narrow-vein mines.

Jan 1, 2003

By Steve Dillingham

PHYSICAL BLAST DATA Pattern Description All measurements related to the description of the physical blast pattern must be made with the mind-set that it has to tell a powerful factual story enabling a future accurate reconstruction of the event. A case has never been lost because too much factual information was available to assist investigators. An accurate physical description of the pattern must be provided based on the blaster’s observations of the pattern actually loaded. The blaster must measure the pattern size, depth, face heights, etc., recording only accurate results. All too often, a blaster records simple pattern sizes and information relayed to him or her from the driller, or from a phone call into the office the night before for powder pre-load inventory purposes. If a pattern was actually measured on the job site by the blaster to be 8.5 x 9.5’, it may, in fact, originally have been ordered at 9’x9’, 8’x9’, or 9’x l0’. In a claim situation, particularly flyrock, recording a “generalization” of what was loaded could result in an interpretation of a blaster’s negligence due to “not knowing or caring” what the actual pattern was, and not loading appropriately for conditions. It is important to remember that other documentation exists such as a drill log from a contract driller or mine records that may provide a different interpretation of the loaded pattern.

Jan 1, 2002

By X Meng, W. A. Hustrulid, M. K. McCarter

Rock excavation in both surface and underground mining is largely accomplished using the drill and blast technique. At the perimeter of such excavations, cautious blasting procedures are often employed to minimize unwanted damage to the remaining rock. Of the several different techniques available, the use of explosive charges with a diameter smaller than the holes in which they are introduced (so-called decoupled charges) is the most common. In spite of the long and widespread use of the technique, a technically sound basis for relating the borehole wall pressure to the explosion pressure is still lacking. Such a relationship is required for optimal design

Jan 1, 2005